MSH Split Case Pump Size (discharge): 1 inch to 32 inch Capacity: 3.4~ 15000 m3/hr Head: 8.6~140m Efficiency:Up to 92% Materials:Cast iron,SS 304,SS 316,Bronze etc MSH Split Case Pump Introduction: MSH Split Case Pump is Horizontal, Split-casing, and Double-suction centrifugal water pump. Double Volute casing is used to contract the axial force due to high head to extend the serve lift time of bearing. Because of the short distance of two bearing, the shaft is shortened to avoid much vibration.. Closed and Circulated cooling system is applied within the sealing house.The Shaft sleeve and O-ring are used to avoid any connection between the shaft and fluid. MSH Split Case Pump Features: Both inlet and outlet of this pump are placed under the axial line,, the pump casing is opened in the middle so it is unnecessary to remove the water inlet and outlet pipelines and motor.if repaired The pump moves CW viewing from the motor side. The pump moving CCW can also be made . Both pump casing and cover form the working chamber of the impeller and there are threaded holes for mounting vacuum and pressure meters on the flanges ant both inlet and outlet have water draining plug on the lower side of flange The impeller is static-balance and dynamic balance tested, fixed by the the side nuts and the Shaft sleeve nuts and its axial position can be adjusted via the nuts and axial force will be get balanced by means of the symmetrical arrangement of its blades, there may be residual axial force which is borne by the bearing at the axial end. This pump shaft is supported by two centripetal ball bearings, which are mounted inside of the bearing chamber on both ends of the pump and lubricated with grease. The double suction seal ring is used to reduce the leakage.. This pump is driven directly via flexible coupling.(V-belt driving will be available if required). The shaft seal is mechanical seal or packing seal . MSH Split Case pump Parameter Selection Table: Pump model Capacity(m3/h) Head(m) Speed(rpm) Power(KW) MSH150 112--220 35--84 2900 30--55 MSH200 160--351 31--100 2900 37--110 MSH250 324--612 8.6--65.1 1450 22--132 MSH300 504--1663 8.7--140 1450--1470 22--680 MSH350 745--1570 10--125 1450--1470 55--630 MSH400 900--1620 32--85.5 980--1480 440--500 MSH500 1150--3800 10.6--108 740--970 110--800 MSH600 2300--4000 13--80 730--970 145--730 MSH700 2111--4896 39.5--99.5 742--980 397--1252 MSHS800 3960--6878 23--84 600--750 450--1600 MSH1000 6600--9900 32--52 600 1250 MSH1200 5832--14400 6--95.7 500--745 710--3450 MSH Split Case pump On-site Application: MSH split case pump is suitable for transporting pure water or liquids with physical and chemical properties to water. Suitable for mine Suitable for water supply and drainage in factory. Suitable for power station. Suitable for urban water supply and drainage Suitable for flood control.
High Efficiency Counter Current Inclined Mixer :- Operation is based on counter current principle. The eccentrically placed high energy agitator rotates in counter clockwise direction within the clockwise rotating pan. In addition, the inclined arrangement 30 degree pan , mixing pan tumbles the material & ensures vertical mixing . A material deflector plate prevents material sticking to pan wall scaper from top to bottom & deflects it into high speed rotor. Further it also accelerates the discharge of material at the end of mixing cycle. SALIENT FEATURES :- Hydraulic actuated central discharge system . Gear and Pinion drive for the mixing pan results in low noise and reduced maintenance, The rotating mixing pan is enclosed in static case resulting dust free operation. For low speed application agitator is directly driven by geared motor whereas for high speed application it is driven by 'V' belt drive. A large hinged door provided on the rotating pan gives easy access to inside of pan. Perfect alignment of mixing pan at high loads/speeds by specially designed slewing ring which guide the pan both in horizontal & vertical direction. All greasing points are connected to a Auto centralized lubrication system thus ensuring high reliability operation. Out side pan cover door & drive arrgt to be provided by soft plastic easy opener ..
As a leading manufacturer, Aeon Brass manufacture and export various types of Copper Componentss which are used to attached elements to concrete. Copper Componentss are manufactured from high quality and standard brass, free cutting brass, steel alloys and other material composition based on custom specification. Copper Componentss are available in various types such as Brass Concrete Anchors, Brass Knurling Anchors, Brass Pool Anchors, Brass Sleeve Anchors, Brass Spring Anchors, Copper Components with Thread, Brass Drop-In Anchor, Brass Plain Anchors, Brass Round Stud Anchors, Brass Slotted Anchors, Brass Wedge Anchors, Brass Expansion Anchors and many more. Copper Componentss are temperature resistant, simple, and easy to apply. They are widely used in wood to Foundation, Load Transference, Tethering, Gym Equipment, Building material, concrete, brick and more. Copper Componentss are widely used for all light and medium duty fixing in Building Industry, automotive industry, Electrical, Sanitary Installation work, Air conditioning, Mounting of suspended ceilings, heating systems etc. We customize dimension upon customers??s needs and requirements. Fabrication: IS 319 Brass Free Cutting. Brass BS 4183, BS 3643, BS93. Brass IS 1367/1366. High-Grade Free Cutting. CDA 360 Brass Alloy.As Per Customers Specified Compositions. Threads: Cutting Punching Bending Plating Coating Sleeving Turning Tapping Twisting Milling Drilling Forging Stud Fixing Ultrasonic Welding Specialized in Cold Forming Applications: Switchgears Power Transmission And Distribution Transformers Electrical Motor And Generator Components Of Electrical Vehicle Wind Power Switchboards Bus Ducts Electrical Panel Transformer Bushing Industries
NO OE # Chevrolet AVALANCHE Base 2003, 2004, 2005, 2006, 2007 12384980 Chevrolet AVALANCHE SUT Base 2003, 2004, 2005, 2006 12584314 Chevrolet Silverado Base 2003, 2004, 2005, 2006, 2007 5170543AA Chevrolet AVALANCHE SUV Base 2003, 2004, 2005, 2006 88962314 GMC Sierra Base 2007 1 GMC Sierra 3500 Base 2007 600-910 Chevrolet Silverado 2500 Base 2003, 2004, 2005, 2006 GMC Sierra 2500 Base 2007 Chevrolet Silverado 3500 Base 2003, 2004, 2005, 2006 Chevrolet Tahoe Base 2003, 2004, 2005, 2006, 2007 Chevrolet Silverado SS 2003, 2004, 2005, 2006, 2007 Chevrolet Tahoe 4DR Base 2003, 2004, 2005, 2006 Chevrolet SUBURBAN Base 2003, 2004, 2005, 2006, 2007 Chevrolet AVALANCHE Base 1999, 2000, 2001, 2002 Chevrolet AVALANCHE SUT Base 2002 Chevrolet AVALANCHE SUV Base 2000, 2001, 2002 Chevrolet BLAZER 1999, 2000, 2001, 2002, 2003, 2004, 2005 Chevrolet K1500 1998, 1999, 2000 Chevrolet K2500 1998, 1999, 2000 Chevrolet K3500 1998, 1999, 2000 2 12384968 Chevrolet PICKUP 2001, 2002, 2003 88962312 Chevrolet S10 1999, 2000, 2001, 2002, 2003, 2004, 2005 600-909 Chevrolet Silverado Base 1999, 2000, 2001, 2002 Chevrolet Silverado 2500 Base 1999, 2000, 2001, 2002 Chevrolet Silverado SS 1999, 2000, 2001, 2002 Chevrolet SUBURBAN Base 1998, 1999, 2000, 2001, 2002 Chevrolet Tahoe 2DR Base 1998, 1999 Chevrolet Tahoe 4DR Base 1998, 1999, 2000, 2001, 2002 Chevrolet Tahoe 4DR CLASSIC 1998, 1999, 2000 Chevrolet Tahoe Base 1998, 1999, 2000, 2001, 2002 Chevrolet TRAILBLAZER Base 1999, 2000, 2001, 2002, 2003, 2004, 2005 Chrysler 05156106AF Jeep 05156106AD Dodge 3 05156106AE 05156106AF 5143477AA CHRYSLER ASPEN 4.7L, 5.7L V8 2007-2009 4 CHRYSLER SEBRING 4.7L, 5.7L V8 2011 DODGE DAKOTA 3.7L, 4.7L V6, V8 2005-2011 DODGE DURANGO 3.7L V6, 4.7L AND 5.7L V8 2005-2012 DODGE RAM 1500 3.7L V6, 4.7L AND 5.7L V8 2006-2012 DODGE RAM 2500 5.7L, 6.7L V8 2006-2012 DODGE RAM 3500 5.7L, 6.7L V8 2006-2012
BX cycloidal reducer, ZDY, ZLY, ZSY gear reducer, ZLYJ gear box, DCY reducer, GR helical geared motor, GS helical worm geared motor, GK helical bevel geared motor, GF parallel helical geared motor, PV bevel gear box, MBY edge-driven geared reducer.
Gear pumps, twin gear pumps, vane pumps, water pumps, fire fighting pumps, fuel transfer pumps, flow meter, lc meter, electrical motors, gear reducer box, diesel operator water pumps, petrol operated water pumps, all type of tankers, pipe line fabrication, storage tank fabrication, aluminum gangway, electrical starter & control panels, electric motor generators re-windings, ball valves, gate valves , flate trailer, aluminum cam lock fitting, v-belt drive pulleys & tyre couplings, flange type & pin bush type coupling, GI fitings.
Brief Introduction for motorized material transfer trolley This kind of motorized material transfer trolley is powered by battery, the batteries supply electricity to the DC motor through the electrical control system to start, stop ,go forward and backward, adjust the speed and so on. Features for motorized material transfer trolley Suitable for low working frequency, spray paint room, dust workshop and other flammable and explosive environment. Structure of motorized material transfer trolley
Product Introduction About the motorized battery transfer trolley is a rail type transportation trolley that lays a track on the ground, and the laid rail is generally an I-shaped surface contact rail. The performance characteristics of the motorized battery transfer trolley is that it has a large bearing capacity, is not afraid of dirty and squeaky, easy to maintain, and has a long service life. The motorized battery transfer trolley can be equipped with industrial wireless remote control devices to achieve artificial remote control. The motorized battery transfer trolley has a simple structure, easy using and operation. It is commonly used in construction materials, stone materials, metal processing, tunnel engineering, iron and steel metallurgy, hydropower industry, aerospace war industry, ship terminals, automobile machinery and other fields. Product Function 1.Load-bearing transport Load-bearing transport is the most basic and important function of motorized battery transfer trolley. 1. Turning This series of motorized battery transfer trolley have the function of running on S-shaped, C-shaped, curved rails, etc. 2. Lift The hydraulic lift system can be installed on the motorized battery transfer trolley to achieve lifting and other functions 3. Side flip: The motorized battery transfer trolley can realize self-discharging by the hydraulic device. 4. Safety devices Safety devices can be installed on the motorized battery transfer trolley, for example, proximity switches, dead man stop, alarm systems, buffers to achieve the corresponding safety functions. 5. Others: The company can research and develop the corresponding non-standard motorized battery transfer trolley to achieve the required functions according to the customers' requirements.
Products Introduce About the motorized material transfer vehicle, it is an electric transfer vehicle without rails, which is the special type compared with traditional motorized material transfer vehicle. More importantly, it has been new favorite in the industry transport field all over the world with hot market. Especially for the workshop that it exists unfixed running distance. This kinds of motorized material transfer vehicle is powered by battery, which is installed inside of vehicle body. The battery supply power to the DC motor through the electrical control system. We use this principle to operate the motorized material transfer vehicle start, stop, go forward and backward, and so on. Maintenance Free Battery About the battery, the maintenance free type battery also is chosen to export. This kinds are convenient, and long lifetime, we needn't maintain once a regular time. so in this series motorized material transfer vehicle, it is popular among customers. Generally speaking, the charging time is about 8 hours. PU Wheel About the motorized material transfer vehicle's wheels, the material is PU wheels, inside is cast steel, outside is encapsulation. By the design, its main function is damping. In our motorized material transfer vehicle, this kinds are also choose. And the wheel are manufactured and assemblied by ourselves. Intelligent Charger Generally speaking, the intelligent charger is chosen to export, it has high frequency, little interference to the grid, and small volume. The charger can not only realize rapid charging, but also no damage to the battery, and prolong battery lifetime. Advantages This kinds of motorized material transfer vehicle needn't run via the rails, which gets rid of relying for the rails. It can not lead to impairment for the cement ground, and can run freely, go forward, back forward, turning... This kinds of motorized material transfer vehicle is battery powered, so only charged fully, can it run freely without limited distance. The motorized material transfer vehicles are customized as per your true demand.
Brief Introduction for motorized material transfer trolley This kind of motorized material transfer trolley is powered by battery, the batteries supply electricity to the DC motor through the electrical control system to start, stop ,go forward and backward, adjust the speed and so on. Features for motorized material transfer trolley Suitable for low working frequency, spray paint room, dust workshop and other flammable and explosive environment. Structure of motorized material transfer trolley Trolley frame, driven mechanism, transmission mechanism, DC motor, battery, control system and other parts.
Product Introduce The kinds of electric motorized transfer car, which is powered by conducting rail, two phase, AC 36V safe voltage, to connect the two railway respectively. The car's wheels and conducting plate lead the AC 36V electricity to the electrical appliance box which is installed on the cart. And AC 36V is transformed to AC380V through transformer. Then control AC motor through AC control system to make the electric motorized transfer car start, stop, go forward, back forward an so on. The electric motorized transfer cars are no limitation of cable, it can get powered from railway in any time. However, it is has strict requirement for the railway, which have to be insulated. (its railway is insulated with the ground, and its wheels are insulated with the ground.) Cart Frame The vehicle frame is two longitudinal beam, several beams with steel panel welded together, which adopts box beam structure according to the crane principle and combined with the design of the cars. Its main feather: large load bearing, little table deformation, long service lifetime.. Railway Wheel About the electric motorized transfer car' wheel, it is single rim of corner case, the material is ZG55, or can be customized as per your demand. It can improve the load capacity and install easily. And the wheel are manufactured and assemblied by ourselves. Lifting Hole The lifting hole are installed on the electric motorized transfer car for convenient transporting. Especially, it can be lifted and moved after the structure finished. What's more, it makes the appearance more delicate and beautiful. Sound & Light Alarm For safe running, it is installed on the electric motorized transfer car, it will ring continuously to warn someones when the electric motorized transfer car start running. Of course, the other parts can be installed, as dead man stop, emergency stop, anti-colliding switch... all can be meet only you'd like by our professional team. url:http://www.newld-transfercar.com
Products Introduce The motorized transfer bogie is powered by storage battery. The storage battery is installed in the motorized transfer bogie. The storage batteries supplied the electricity to the DC motor through the electrical control system. Use this principle to operate the motorized transfer bogie to starting, stopping, going forward, going backward, adjusting the speed and so on.
Products Introduce The kind of motorized material transfer trailer, which lead AC380v to the motorized material transfer trailer as the power source. You can put the sliding line in the hole, if your motorized material transfer trailer approaches to the wall, the sliding wire also can be fixed on the wall, what we do not only can save the space but could reduce the impair for the ground. Of course, it can be customized according to your requirement. Due to its low cost, high frequency, simple structure, The motorized material transfer trailer is the first choice for the factory which has been widely used in industry field. Railway Wheel About the railway wheel of motorized material transfer trailer, it is single rim of corner case, the material is ZG55, or can be customized as per your demand. It can improve the load capacity and install easily. And the wheel are manufactured and assemblied by ourselves. Three-in-one Type Reducer, Motor and Brake This type gear box with advantage of high efficiency, operate steadily, easy installation and maintenance, etc. Brake is composed by brake frame, brake parts, brake operating device and so on, it is a safety device to ensure the motorized material transfer trailer working safely. The electric motor is AC motor. Sliding Line The sliding line is limited by the position, it can be installed between the two rails. The hole should be digged or it can also be placed in the channel outside the rail. In order to the safety and convenience, the border should be added on the channel.
Products Introduction About the motorized transfer car, it is an electric transfer car powered by towing cable which is laid on the ground. The cable line is placed between the two rails or oneside. The operation system is low voltage 36V power. It has widely applied in the industry transportation field all over the world. Our electric transfer car is available in a number of configurations specifically designed to suit the needs of our customers. Car Frame The frame adopts box beam structure according to the crane principle and combined with the design of the motorized transfer car. It is with large load capacity, long service lifetime. Besides, not easy deformation and can effectively ensure the smooth of the platform. Railway Wheel About the electric transfer car's wheels, it is double rim of corner case, the material is ZG55, or can be customized as per your demand. It can improve the load capacity and install easily. And the railway wheels are manufactured and assemblied by ourselves. Three In One Reducer & AC Motor This type gear box with advantage of high efficiency, operate steadily, easy installation and maintenance, etc; Brake is composed by brake frame, brake parts, brake operating device and so on, it is a safety device to ensure the electric transfer car working safely; The electric motor is AC motor.
Brief Introduction Of Motorized Rail Transfer Trolleys This series motorized rail transfer trolleys running on rails which is powered by dragging cable. It conducts AC 380v directly into the electrical control system of the motorized rail transfer trolleys to let it start, stop, go forward and backward and so on. The dragging cable is laid on the ground. The cable line is place between the tow rails. The operated system is low voltage 36v power. Features Of Motorized Rail Transfer Trolleys Compared with KPX(battery power) series transfer trolleys, the using time of motorized rail transfer trolleys are unlimited. Compare with KPD(conductor rails power) series transfer trolleys, the motorized rail transfer trolley have no strict requirement on the rails. Compared with KPJ(cable reels power) transfer trolleys, the cost of the motorized rail transfer trolleys are lower. Advantages Of Motorized Rail Transfer Trolleys This series' motorized rail transfer trolleys are suitable to be used in the bad environment, for example, high-tempeture and anti-explosion condition; AC motor, simple structure, not limited for the using time; It has no strict requirement on the rail's installation; Cost is not high, easy to operate and maintenance; The motorized rail transfer trolleys are customized as per your true demand.
Wheelbarrow, trolleys, warehouse trucks, tool carts, drum dolly, kid's wagon, multi-functional table and wind motor.
1. About the Manual The Lake Drilling MOTOR is a powerful and reliable positive displacement motor. The motor generates an optimum balance of rotational speed and high torque to drive a variety of drill bits at speeds that maximize tool life and performance. LAKE MOTORS offers a choice of flow rates, speeds, and torques to match a wide range of operational parameters. LAKE MOTORS are used in applications such as straight hole drilling, directional (steerable) drilling, horizontal drilling, hole opening, and re-entry(work over). 2.Description of downhole motor 1.The down-hole drill motor is a kind of downhole drill tool driven by mud. 2.As mud fluid from the mud pump enters the motor via the bypass valve, a certain pressure difference is formed at the inlet and outlet of the motor, pushing the rotor to rotate. Torque and rotate speed are transferred via the cardan shaft and the driving shaft to the bit. 3. Performance of the down-hole drill motor depends mainly on performance parameters of the screw motor. 4.This product uses the high and new technology of coating to avoid coating off of rotors resulted from the traditional technology. Its strength and life are greatly improved. 5.It is applicable to directional drilling,horizontal drilling, composite drilling, cluster wells, sidetrack wells and well workover etc. 3. Advantage of downhole motor Increased rate of penetration. Better hole deviation control. Reduction in drill string failure rate. Reduction in wear and tear of the swivel, Kelly, and rotary drives. Reduction in fuel cost, since compared to rotary drilling, less energy is required to power a downhole motor.
Rail transfer cart , mold transfer trolly, trackless transfer cart, coil handling cart , steel coil transfer car, railway inspection vehilce, heavy duty agv, industrial turntable transfer car, non power industry trailer, , ferry transfer cart, material handling equipment , die mold cart, factory use handling cart, cable drum powerd transfer cart, battery operated transfer car, truck tractor, ladle transfer car, hydraulic lifting transfer car, automatic guided vehicle.Shipping
SYNCHRONOUS MOTOR Basic model: T, TKS, TD Armature diameter: Â 1200- Â 3550mm Power: 200 800000Kw Number of poles: 2-40 Voltage: 690 15000V Frequency: 50HZ, 60HZ Protection level: IP23, IP44, IP54, IP55 Cooling method: IC01, IC611, IC81W Because synchronous motors can operate at advanced power factors by adjusting the excitation current, it is beneficial to improve the power factor of the power grid. Therefore, large equipment, such as large blowers, water pumps, ball mills, compressors, rolling mills, etc., are often driven by synchronous motors. This advantage is particularly prominent when low-speed large equipment uses synchronous motors. In addition, the speed of the synchronous motor is completely determined by the power frequency. When the frequency is constant, the speed of the motor is also constant, and it does not change with the load. This feature is of great significance in certain transmission systems, especially multi-machine synchronous transmission systems and precision speed regulation and speed stabilization systems. The running stability of synchronous motors is also relatively high. Synchronous motors generally operate in an over-excited state, and their overload capacity is greater than that of corresponding asynchronous motors. The torque of an asynchronous motor is proportional to the square of the voltage, while the torque of a synchronous motor is determined by the product of the voltage and the internal electromotive force generated by the motor's exciting current, which is only proportional to the first power of the voltage. When the grid voltage suddenly drops to about 80% of the rated value, the torque of the asynchronous motor often drops to about 64% and stops running because it does not move the load; while the torque of the synchronous motor does not drop much, it can also be forced by Excitation to ensure stable operation of the motor
Hydraulic turbines, hydroelectric generators, standard micro and small hydro units, hydro mechanical equipment, diesel engines, diesel generating sets, large electric motors, electric motor driven compressors, slide bearing shells, forgings, steel, iron and non ferrous metal castings, large welded parts, equipment for chemical.Research activity and tests on its laboratories/stands models of hydraulic turbines
