Parameters: Model: ML-LB2 Laser type: Q-Switched Nd: YAG Laser Laser wavelength: 1064&532nm Pulse energy: 0-800mj 0-300mj Width of Pulse(pulse duration): 0-10ns Repetition rate (pulse rate): 1, 2, 3, 4, 5, 6 (adjustable 0.5-3)Hz Light spot: 1-7mm Power supply: 220V, 6A or 110V, 12A With indicator laser light Net Weight: 9kgs; Size: 35cm*25cm*22cm Gross Weight: 16kgs Size: 50cm*35cm*30cm 1SET
Brief introduction: Simultaneously air temperature and set temperature display. Alarm functions for safety includes Power failure fan failure Over temperature temperature deviation Temperature probe failure >37 pc temperature setting. A keypad locks helps to prevent inadvertent changes to settings. Trough for pulling and pushing add the water and wash is convenient. Heater is electrically cut off if air /skin temperature inside incubator exceed 40fpc. Humidity is adjustable. The infant bed inclination angle is adjustable. Gross weight : Control cabinet: 120kg hood cabinet: 30kg Net weight: Control cabinet: 90kg hood cabinet: 10kg Measurement 1200*700*960mm
Microprocessor based servo controlled temperature system. The microprocessor-controlled unit allows for three settings, pre-warm, manual or automatic. Alarms functions for safety includes: Power failure temperature deviation Temperature probe failure over temperature Convenient x-ray cassette under infant bed. Three variable mattress tilts. Separate white lamp allows convenient observation. Adopts anti-explosion micro crystal quartz infrared radiation tube for its radiation source . Having quick heating and long life span. Digital display to indicate temperature. Have independent the second heat cuts off , the system is more safe. Protection when temperature probe in over temperature. Gross weight : 100kg net weight: 70kg Measurement: 1100*700*960mm
Brief introduction: Simultaneously air temperature and set temperature display. Alarm functions for safety includes Power failure fan failure Over temperature temperature deviation Temperature probe failure >37pc temperature setting. A keypad locks helps to prevent inadvertent changes to settings. Trough for pulling and pushing add the water and wash is convenient. Heater is electrically cut off if air /skin temperature inside incubator exceed 40pc. Humidity is adjustable. The infant bed inclination angle is adjustable. Technical specification: Electrical requirement : 220v+10%/50+2% Power supply : _420va Air temperature control range 2538 Temperature fluctuation: _0.5 Uniformity of mattress temperature: _0.8 Warm-up time: _45min Internal noise level: _55db Operation condition: Environment temperature: 2538 Environment relative humidity: 30%~75%rh Environment air velocity of flow:
Brief introduction: Microprocessor based servo controlled temperature system. The microprocessor-controlled unit allows for three settings, pre-warm, manual or automatic. Alarms functions for safety includes: Power failure temperature deviation Temperature probe failure over temperature Convenient x-ray cassette under infant bed. Three variable mattress tilts. Separate white lamp allows convenient observation. Adopts anti-explosion micro crystal quartz infrared radiation tube for its radiation source . Having quick heating and long life span. Digital display to indicate temperature. Have independent the second heat cuts off , the system is more safe. Protection when temperature probe in over temperature. Technical specification: Electrical requirement : 220v+10%/50+2% Power supply : _1500va Temperature control range: 32~38.5 Temperature probe accuracy: _0.3 Mattress temperature uniformity: _2.0 Warm-up time: _45min Adjustable horizon angle of radiator: +90 Operation condition: Environment temperature: 18~30 Environment relative humidity: 30%~75%rh Environment air velocity of flow:
This system is IPL(intense pulse light) +RF(Radio Frequency), which is the best technology in the market. For this system, you can use IPL only or RF only, or IPL+RF together. System Characteristic: 1.handle cooling system: User may adjust the cooling system to improve the treatment result affected by the constant cooling temperature. 2.the handpiece has fast plug in-out. Water and electricity body cut, automatic diagnosis system insetted. Easy and fast to use. 3.built-in expert system: join the clinical experience we accumulated for several years into the expert system to make sure the system is safe and simple to use. 4.you can upgrade this system through computer. 5.customer design Certification Received: CE Mark Treatment range Almost all the skin problem, such as speck, age spot, pigmentation, wrinkle removal, skin rejuvenation, hair removal, sunburn, rough pores and acne removal. Special features 1. Effective shallower hair removal 2. Independent of skin types 3. A more effective technique for skin rejuvenation as the technology allows for sufficient thermal damage of the target area without overheating surrounding tissue structures. Treatment theory The objective of effective permanent hair reduction and skin rejuvenation is to heat up and injure the target, be it a hair follicle or a vascular or pigmented lesion. The job of the intense pulsed light is to heat up the target to the required temperature and thereby lowering the impedance of the target. The RF current then travels along the path of least impedance (preheated path of the intense light) and gently heats up everything in its pathway. This results in further injury to the target and completes the heating (injury) that is necessary for the desired biologic effect, for example to stop hair growing, or for vascular and pigmented lesions to fade. RF f½s effect is pertaining to the electric density which depends on the impedance. And it is not absorbed by melanin and thus independent of skin types. So it is an optimum resolution for the patient of darker skin or of the shallower hair. Specifications: Light source: intense pulse light IPL Energy Out: 0-40J/cm2 IPL Pulse Repetition Rate 0.5Hz RF Energy Out: 0-100J/cm3 Dimensions: 460mmf-500mmf-900mm Weight: 65kg, portable is 38kg around Input Voltage: 230Vf+, 50Hz Operating Panel: 8.4f+f+ TFT Color touch Screen Cooling: 0-5 centigrade Handpieces: SR, HR, VR, AR
System Characteristic: 1.handle cooling system: User may adjust the cooling system to improve the treatment result affected by the constant cooling temperature. 2.the handpiece has fast plug in-out. Water and electricity body cut, automatic diagnosis system insetted. Easy and fast to use. 3.built-in expert system: join the clinical experience we accumulated for several years into the expert system to make sure the system is safe and simple to use. 4.you can upgrade this system through computer. 5.customer design Certification Received: CE Mark Treatment range Almost all the skin problem, such as speck, age spot, pigmentation, wrinkle removal, skin rejuvenation, hair removal, sunburn, rough pores and acne removal. Special features 1. Effective shallower hair removal 2. Independent of skin types 3. A more effective technique for skin rejuvenation as the technology allows for sufficient thermal damage of the target area without overheating surrounding tissue structures. Treatment theory The objective of effective permanent hair reduction and skin rejuvenation is to heat up and injure the target, be it a hair follicle or a vascular or pigmented lesion. The job of the intense pulsed light is to heat up the target to the required temperature and thereby lowering the impedance of the target. The RF current then travels along the path of least impedance (preheated path of the intense light) and gently heats up everything in its pathway. This results in further injury to the target and completes the heating (injury) that is necessary for the desired biologic effect, for example to stop hair growing, or for vascular and pigmented lesions to fade. RF is effect is pertaining to the electric density which depends on the impedance. And it is not absorbed by melanin and thus independent of skin types. So it is an optimum resolution for the patient of darker skin or of the shallower hair. Specifications: Light source: intense pulse light IPL Energy Out: 0-35J/cm2 IPL Pulse Repetition Rate 0.5Hz RF Energy Out: 0-100J/cm3 Weight: 8kg around Input Voltage: 230Vf+, 50Hz Operating Panel:TFT Color touch Screen Cooling: 0-5 centigrade Handpieces: SR, HR, VR, AR
B. Braun offers a holistic infusion therapy concept which combines high-quality products with intelligent technologies and services
Theory The Professional OPT SHR IPL(Super Hair Removal) system emits varied wavelength, broad spectrum and intense pulse light, which permeate epidermis to the dermis of the skin. with the principle of selective absorption,the light is absorbed by the melanin in the hair follicles.Through the optical & thermal effect generated and sourced from the light, it achieves the purpose of removing unexpected hair by rapid destroying of hair follicle tissues. SHR stands for Super Hair Removal. Adopts Optimal Pulse Technology (OPT), is the most advanced adoption of pulsed light for hair removal and skin rejuvenation. The working principle is heating the dermis to a target temperature gradually, the target temperature damages the hair follicles and prevents re-growing, meanwhile avoiding injury to the surrounding tissue. High repeted pulses are delivered deep into the dermis, achieving high average power and effective heat, without risk of injury or pain.
Application of Fractional CO2 Laser Machina: Fractional mode (Aesthetic) + Pulse mode (Surgery) + Gynae mode (Gynecology Optional) Fractional mode: Skin rejuvenation, Wrinkles removal, Pigment removal, Acne treatment. Pulse mode: Sarcoma removal, Nevus removal, Grown nails removal, Skin tags removal. Gynae mode(Optional): Tighten, Lubrication, Sensitivity, Uremic Treatment.
Vertical Type Fiber Laser Marking Machine Fiber Laser Marking Machine Laser Marking Machine, Laser Marking Machine Manufacturer Features: 1.With foot wheels on the bottom of machine body, this vertical type laser marker can be easily moved to anywhere and fixed it to the ground. Itâ??s very good for marking on some heavy materials which is not easy to be moved. It can be compatible with conveyor belt working table for mass production line. 2. The marking head also can be adjusted for 100cm according to the different thickness of materials. (the height of marking head can be customized.) 3. High quality laser path suitable for delicate marking. Reach to the limit of diffraction. Export TEMOO of fundamental transverse mode. M2 near to 1. Beam divergence angle is only 1/4 of diode laser. Focus dot diameter is not over 20 um. 4. High pulse repeating rate and stable power bring high speed laser marking. Unit pulse power surge is lower than 1%. Easy control laser dot size, thickness and shape. 5. High speed 2-3 times over than traditional diode pumped marking machine. 6. Long lifetime. Ultra-low power consumption of 0.5kw. Efficiency conversion reaches to over 30 %. 7. Suitable for various fiber laser generators, make color-marking on stainless steel (code 304). Applications 1. Applicable Materials: Metal and various non-metallic materials, stainless steel, copper, iron, aluminum, carbon steel, titanium, high hardness alloy, oxide, printing ink, engineering plastics, electroplating materials, coating materials, epoxy resin, ceramic, ABS, PVC, PES, etc. 2. Applicable Industries: Mobile phone keypad, plastic translucent keys, electronic components, integrated circuits (IC), electrical, appliances, communication products, sanitary ware, measuring tools, accessories, knives, eyeglasses and clocks, jewelry, auto parts, plastic parts, medical equipment, luggage buckle, cooking utensils, stainless steel products, building materials and other industries.
808 Diode laser/candela laser best permanent hair removal I Theory 810nm system uses the unique laser with long pulse width 810nm to penetrate into hair follicle.Using the theory of selective optical absorption,laser can be preferentially absorbed by the melanin of the hair. And then the hair shaft and hair follicle are heated rapidly in order to destroy the oxygen-supply organization of and around the hair follicle. The system's unique super-cooling technology could bring about certain anesthetic effect to the epidermis with the output of the laser. Therefore, it could protect the skin from being hurt. As a result, a very safe and effective treatment is realized. II Applications: 1. Hair Removal for all of skin type and hair type. 2. Skin rejuvenation III Advantage 1. The laser wavelength The 810nm near infrared laser of Terminator Hair Removal System is best for absorbing melanin so that it can be applied to different parts and depth of the hair follicle to remove any type of the hair effectively. 2. Long laser pulse width The laser pulse duration of Terminator Hair Removal System is 10ms to 1400ms adjustable, which can impose effective treatments according to different hair to realize permanent hair removal. 3. No pigmentation. Suitable for any kind of skin. 810nm diode laser hair removal system uses the most advanced technology that penetrates deeper than before so that the skin could absorb less laser and there is no pigmentation. 4. Sapphire contact cooling system can make the treatment safer and no harm to the skin.The temperature of skin can be arrive at 0~5°C Sapphire contact cooling system of Terminator hair removal equipment can ensure the doctor could use the maximum energy but not to hurt normal skin. This cooling system can make sure no hurt to the skin when patients are given more pressure. It is reported that the pressure can increase 30%-40% of the luminous energy. 5. The squared big spot size can prompt the treatment speed. 810nm diode laser hair removal machine uses big squared spot size of 20mm which could ensure high efficiency and fast speed when executing the treatment of large area hair removal. Because the spot size is big, it could avoid repeated treatment.
Our Technology Advantages AFT Technology Adopt a multi-spectrum pulsed light which filters out the wavelength above 950nm to keep much water in the target skin so that the treatment is painless. EDF Technology To make sure the energy of every shot and pulse is the same and stable to keep safe treatment. In-montion Operation To shorten the time of treatment session, Accelerate the operation, save 1/2 treatment time Painless 1. Specific wavelength keeps much water in the target skin 2. EDF (Equally Distributed Fluence) ensures the uniform of energy Self-checking & monitor Monitor water circulation and identified handpiece to keep safe working Charging-Monitor Ensure the capacitors charging energy correctly Identified Handpiece Ensure safety Automatical Calibrate Constant and accurate energy output Application It could be used for hair removal and improving skin conditions. Besides, it can be used for all kinds of skin blemishes and skin diseases. Hair Removal Such as armpit hair, beard, lip hair, hairline, bikini hair, body hair Skin Rejuvenation Skin whitening, minimize pores, repair rough skin, enhance skin elasticity, smooth tiny wrinkles, eliminate and fade acne scars Pimples Acne, allergic acne, crusted acne Specifications Model S6 Light Source Pure Sapphire Spot Size SHR: 15*50mm SSR 8*40mm Wavelength 420-950nm for SAC(Optional), 570-950nm for SSR(Skin Rejuvenation), 650-950nm for SHR(Hair Removal) Power 220V/50Hz, 110V/60Hz Xenon Lamp Imported Lamp Fluence 1-7J/cm2 for SHR, 1-12J/cm2 for SSR(SAC, Optional) Timer 1s, 3s and 30s for SHR 1s, 2s, 12s for SSR(SAC, Optional) Frequency 3Hz for SHR, 2Hz for SSR(SAC, Optional) Intergrated Cooling 1-4 Degree Display 10.4" Colorful Touch Screen Calibrating Machine Automatic Calibrated Water Cooling Circulated Monitored In-scene Working Environment Indoor Use Only 35KG
Our Technology Advantages AFT Technology Adopt a multi-spectrum pulsed light which filters out the wavelength above 950nm to keep much water in the target skin so that the treatment is painless. EDF Technology To make sure the energy of every shot and pulse is the same and stable to keep safe treatment. In-montion Operation To shorten the time of treatment session, Accelerate the operation, save 1/2 treatment time Painless 1. Specific wavelength keeps much water in the target skin 2. EDF (Equally Distributed Fluence) ensures the uniform of energy Self-checking & monitor Monitor water circulation and identified handpiece to keep safe working Charging-Monitor Ensure the capacitors charging energy correctly Identified Handpiece Ensure safety Automatical Calibrate Constant and accurate energy output Application It could be used for hair removal and improving skin conditions. Besides, it can be used for all kinds of skin blemishes and skin diseases. Hair Removal Such as armpit hair, beard, lip hair, hairline, bikini hair, body hair Skin Rejuvenation Skin whitening, minimize pores, repair rough skin, enhance skin elasticity, smooth tiny wrinkles, eliminate and fade acne scars Pimples Acne, allergic acne, crusted acne Specifications Model G80 Light Source Pure Sapphire Spot Size SHR: 8*40mm SSR 8*40mm (Optional) Wavelength 650-950nm for SHR(Hair Removal) 420-950nm for SAC(Optional), 570-950nm for SSR(Optional), Power 220V/50Hz, 110V/60Hz Xenon Lamp Imported Lamp Fluence 1-7J/cm2 for SHR, 1-12J/cm2 for SSR(SAC, Optional) Timer 1s, 3s and 30s for SHR 1s, 2s, 12s for SSR(SAC, Optional) Frequency 2Hz for SHR, 2Hz for SSR(SAC, Optional) Intergrated Cooling 1-4 Degree Display 8.4" Colorful Touch Screen Calibrating Machine Automatic Calibrated Water Cooling Circulated Monitored In-scene Working Environment Indoor Use Only 20KG
Our Technology Advantages AFT Technology Adopt a multi-spectrum pulsed light which filters out the wavelength above 950nm to keep much water in the target skin so that the treatment is painless. EDF Technology To make sure the energy of every shot and pulse is the same and stable to keep safe treatment. In-montion Operation To shorten the time of treatment session, Accelerate the operation, save 1/2 treatment time Painless 1. Specific wavelength keeps much water in the target skin 2. EDF (Equally Distributed Fluence) ensures the uniform of energy Self-checking & monitor Monitor water circulation and identified handpiece to keep safe working Charging-Monitor Ensure the capacitors charging energy correctly Identified Handpiece Ensure safety Automatical Calibrate Constant and accurate energy output Application It could be used for hair removal and improving skin conditions. Besides, it can be used for all kinds of skin blemishes and skin diseases. Hair Removal Such as armpit hair, beard, lip hair, hairline, bikini hair, body hair Skin Rejuvenation Skin whitening, minimize pores, repair rough skin, enhance skin elasticity, smooth tiny wrinkles, eliminate and fade acne scars Pimples Acne, allergic acne, crusted acne Specifications Model AFT-600 Light Source Pure Sapphire Spot Size SHR: 15*50mm SSR 8*40mm Wavelength 420-950nm for SAC(Optional), 570-950nm for SSR(Skin Rejuvenation), 650-950nm for SHR(Hair Removal) Power 220V/50Hz, 110V/60Hz Xenon Lamp Imported Lamp Fluence 1-7J/cm2 for SHR, 1-12J/cm2 for SSR, (SAC, Optional) Timer 1s, 3s and 30s for SHR 1s, 2s, 12s for SSR (SAC, Optional) Frequency 3Hz for SHR, 2Hz for SSR, (SAC, Optional) Intergrated Cooling 1-4 Degree Display 12.1" Colorful Touch Screen Calibrating Machine Automatic Calibrated Water Cooling Circulated Monitored In-scene Working Environment Indoor Use Only 141*70*55cm3 65KG
Our Advantages Germany Osram LED Lamps: The best quality lamp to ensure effective energy and longer life span SMD LED: To ensure good heat-dissipation and high energy tranfer rate Interchangeable Treatment Heads: One machine with several heads to make sure the effectiveness and cover all the applications Intelligent Treatment Heads: Identified by the machine to ensure total safety and simplify work Two Operation Modes: 1. Simple Mode: Easy for beginners to operate 2. Expert Mode: Useful for clinics, can save programs in advance to save time and simplify work 10.4'' colorful touch screen: Easy to operate Multiple Languages: Can be used by people from any country Articulated Arm: Revolve 360 degree, convenient to adjust the position of the treatment head Adjustable 5 PCB Panels: Convenient to adjust the shape of treatment head according to target place Application Blue Light 469nm Acne, Pimples, Inflammation of the Skin Therapy, Comedones Improved Red Light 633nm Anti-aging, Reduce Fine Lines & Wrinkles, Improve Skin Texture, Clear Photo Damaged Skin, Skin Repair Infrared Light 850nm Improve Micro-circulation and metabolism, can be used with Blue or Red light to deliver better treating results Yellow Light 595nm Help the lymph system to detoxify your body Green Light 530nm Reduce pigmentation through penetration into base skin layers, Prevent the forming of fleck, Keep skin smooth and bright 70*77*117cm3 35KG
Theory The Diode Laser Hair Removal Equipment emits 808nm high-energy continuous laser. The laser is particularly sensitive to hair follicle melanocytes, but does not damage the normal epidermis. It directly acts on the hair follicle melanin to produce a photothermal effect, and the hair follicle is heated to 45-50 degrees Celsius. Maintaining for a period of time can achieve the destruction of hair follicles and their stem cells, and achieve the purpose of permanent hair removal. Specification Model NO. MED-808m Laser Type High Power Diodes/Diode Laser Hair Removal Equipment Wavelength 808nm Standard 755nm, 1064nm, Tri-wavelength optional Changeable Spot size 9 9, 12 12, 12 18 optional Spot Size 12 12mm Repetition Rate up to 10HZ Fluence 10-125J/CM2 Pulse Width 10-400ms Peak Power 2500W Platform Specifification 100-240VAC 12A MAX/50-60HZ Net Weight 27KG Dimension 397mm 357mm 463mm Advantage �·Safe and Comfortable, Double Benefits Diode Laser Hair Removal Equipment with double TEC Active Cooling Modular brings twin cooling effects. Double TEC starts working when water temperature is above 25C, to make sure water temperature between 25C and 30C, and pure sapphire cool enough. In this case, the safest and most comfortable treatment is available. Super long continuous working time will double your business. Easy Touch and Intelligent Diagnostic System Diode Laser Hair Removal Equipment with easy touch software provides recommended settings for various skin types and hair colors to end users, makes operation no difficult any more. Smart errors diagnostic system provides Working Notes for important components such as fans, pump and cooling system. Half your time and cost invest in after sales service. Before&After Package&Delivery Package Standard Flight Case Delivery Within 3-4 Working Days Shipment Door to door(DHL/TNT/UPS/FEDEX), By air, By sea
Place of Origin:Guangdong, China Brand Name:QIZHE Model Number:QZ-008 IPL+ RF:YES After-sales Service Provided:Online support, Video technical support Type:IPL Certification:ce, ISO9001 Feature:Hair Removal, Skin Rejuvenation Application:For Home Use Keyword:Home Use Painless Hair Remover Technology:ice cooling + battery Weight:460g Wavelength:550-1200nm Voltage:110-240V power:48W Battery:2600mAh Charge time:2 hours service:OEM/ODM/24hours Online Service warranty:12 month
Product Name Handheld IPL Hair Removal Advanced Dropshipping Home Use Handset IPL Hair Removal Wavelength:510-1200nm Enerygy levels:4Modes Working voltage:110-240V Working frequency:50-60Hz Power:36W Lifespan:600000Flashes Color:Color can be customized Size:130*70*40mm Technology:RF+ Skin color recognition. Weight:220g Zhongshan Qizhe Technology Co., Ltd., a professional manufacturer of beauty equipment in China. 1. 15 years' experience for OEM and ODM 2. Our products get the certificate of CE, ROHS, FCC 3. Offer one-stop service include the layout and produce PCB, design the housing, mold tooling, printing and assembly. 4.There are 2 SMT production lines (1500pcs/ hour) + 6 production lines (5000pcs per day) can meet large quantity requirement in our company. 5.We have more than 30 inspectors ,who are responsible for material checking , production quality control,finished products inspection and serve to the third inspection 6.Professional R&D team with more than 40 + engineers 7. 8000 square meters factory, 400+ staffs, 24 hours online service 8. Our high-quality products are utilized in over 120 countries around the world and have already won an international reputation, attracting customers with advanced technologies, unique designs, powerful functions, and efficient services.markets include American, Europe, Japan, South Korea, Middle East, and South-east Asia countries. Welcome to our company and we will provide you with the best equipment and services.
980nm diode laser spider vein removal machine Function 1Remove all kinds of spider veins and vascular from the body surface. Function 2Ice Compress Hammer Hanptech is a company specializing in semiconductor laser equipment. It locte in beijing of china,For more than a decade, we have developed a wide range of instruments from 450 nm to 1920 nm. The functions cover vascular vein removal, pain treatment, Onychomycosis treatment, skin rejuvenation, remove wrinkles ,remove freckle, acne treatment, lipolysis, anti-inflammatory analgesia, photodynamic therapy, LLLT stimulation, laser dentistry treatment , no bleeding laser scalpel and many other functions, including beauty medical, sports rehabilitation, biological monitoring, veterinary (animal, pet) laser applications, And so on. The company's professional focus allows us to have OEM/ODM capabilities, and you can customize any of these instruments you need, from function to performance and appearance or shape. We only cooperate with agents and dealers, not selling to terminal markets. If you are a agents or channel provider in the domian, need more product informations. there are some product list. 1.Vascular vein removal single function with ice compress hammer(15/20/30watt options) 2.Vascular vein removal four function 4in1 with ice compress hammer(15/20/30watt options) 3.Veterinary laser therapy 4.Semiconductor laser to remove freckles 5.Semiconductor laser skin rejuvenation please contact us
