Semiconductor Test Probe Pogo Pin SCPB038 for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCFB038 we will introduce is 0.38 mm in barrel diameter and 6 mm in total length. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 1.5 amps. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 1 mm. But it is better to be pressed at a distance of 0.6 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.6 mm, the loaded force is about 25 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Ph, Au on Ni Plated Bottom Plunger: BeCu, Au on Ni Plated Top Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 1.5 amps Contact Resistance: 100 milliohms max Bandwidth: 5.3 GHz at -1dB Propagation Delay: 27 ps Inductance: 1MHZ at -0.02809 uH Captance: 1MHZ at 0.876347 uF Specifications: Full Stroke: 1 mm Rated Stroke: 0.6 mm Spring Force: 25 7 gf at load 0.6 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Spring Loaded Pogo Pin Test Probe BIP68 Series for Battery Contact Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP68 series of battery contact probes. The outside diameter is usually 0.68 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 0.95 mm (37 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms (Maximum) Full Stroke: 0.5 mm Rated Stroke: 0.4 mm Spring Force: 10 gf (0.35 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
In-circuit Test Probe Pogo Pin PE75 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PE75 series here. Its test center is 75 mil. The diameter is 1.91 mm and the total length is 33.1 mm. Various tip styles, for example, A, B, U, H, K, L, BK, etc., are available for test probes. There are roughly three types of receptacles, namely CR, SC and WW to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.91 mm (75 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms Mounting Hole Size: Diameter 1.35 mm Full Stroke: 6.4 mm Rated Stroke: 4.3 mm Spring Force: 150 gf (5.5 oz)/200 gf (7.2 oz)/227 gf (8 oz) Materials Receptacle: Brass, Gold Plated Contact Barrel: Phosphor Bronze, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Nickel Plated or Gold Plated semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Pogo Pin Test Probe BIP47 Series for Battery Contact Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP47 series of battery contact probes. The outside diameter is usually 1.6 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 2.54 mm (100 mil) Current Rating: 3 Amps, continuous Contact Resistance: 20 milliohms (Maximum) Full Stroke: 1.5 mm Rated Stroke: 1.5 mm Spring Force: 80 gf (2.8 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Semiconductor Test Probe Spring-Loaded Pogo Pin SCPA031(21) for Chip Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPA031(21) we will introduce is 0.31 mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold. The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 2 Amps. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 0.7 mm. But it is better to be pressed at a distance of 0.45 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.45 mm, the loaded force is about 20 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Ph, Au on Ni Plated Bottom Plunger: BeCu, Au on Ni Plated Top Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 2 amps Contact Resistance: 100 milliohms max Bandwidth: 7.4 GHz at -1dB Inductance: 1MHZ at -0.05996 uH Captance: 1MHZ at 0.425647 uF Specifications: Full Stroke: 0.7 mm Rated Stroke: 0.45 mm Spring Force: 20�?�±6 gf at load 0.45 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Semiconductor Test Probe Pogo Pin SCFE035 for Integrated Circuit Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCFE035 we will introduce is 0.35 mm in barrel diameter and 18 mm in total length. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold The bottom plunger is made from SK4 plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 1.5 amps. The typical maximal contact resistance is about 150 milliohms. The plunger can be pressed at a distance of up to 1.5 mm. But it is better to be pressed at a distance of 1 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 1 mm, the loaded force is about 38 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Ph, Au on Ni Plated Bottom Plunger: SK4, Au on Ni Plated Top Plunger: SK4, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 1.5 amps Contact Resistance: 150 milliohms max Bandwidth: 9.3 GHz at -1dB Inductance: 1MHZ at -0.05517 uH Captance: 1MHZ at 0.462432 uF Specifications: Full Stroke: 1.5 mm Rated Stroke: 1 mm Spring Force: 38�?�±11 gf at load 1 mm Mechanical Life: about 200000 cycles For more information, please check below catalog. Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Semiconductor Test Probe Pogo Pin SCPA030 Series for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPA030 we will introduce is 0.3 mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold or gold clad phosphor bronze. The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 2 Amps. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 1.1 mm. But it is better to be pressed at a distance of 0.65 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.65 mm, the loaded force is about 10 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Ph/ SP, Au on Ni Plated Bottom Plunger: BeCu, Au on Ni Plated Top Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 2 amps Contact Resistance: 100 milliohms max Bandwidth: 7.1 GHz at -1dB Inductance: 1MHZ at -0.02524 uH Captance: 1MHZ at 1.12735 uF Specifications: Full Stroke: 1.1 mm Rated Stroke: 0.65 mm Spring Force: 10 ±3 gf at load 0.65 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Battery Contact Probe Test Pogo Pin BIP148 Series for Connector Application Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP148 series of battery contact probes. The outside diameter is usually 1.49 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 2.16 mm (85 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms (Maximum) Full Stroke: 2 mm Rated Stroke: 1.33 mm Spring Force: 25 gf (1/ 0.9 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
In-circuit Test Probe Pogo Pin P085 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe P085 series here. Its diameter is 0.82 mm and the total length is 37 mm. Various tip styles, for example, H, S, T, E, C, U, G, etc., are available for test probes. For details, please check below parameters. Technical Specifications Recommended Rated Stroke: 2 mm Spring Force: 130 gf (5oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated For more information, please check below catalog. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Pogo Pin Test Probe BIP114 Series for Battery Contact Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP114 series of battery contact probes. The outside diameter is usually 1.14 mm and there are some common tip styles, for example round head or pointed head. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.91 mm (75 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms (Maximum) Full Stroke: 1.14 mm Rated Stroke: 1.14 mm Spring Force: 110 gf (4 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Pogo Pin Semiconductor Test Probe SCPA025 Series for IC Test Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPA025 we will introduce is 0.25 mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold or gold clad phosphor bronze. The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 1 Amp. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 1.1 mm. But it is better to be pressed at a distance of 0.65 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.65 mm, the loaded force is about 14 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel�¯�¼? Ph/SP, Au on Ni Plated Bottom Plunger�¯�¼? BeCu, Au on Ni Plated Top Plunger BeCu, Au on Ni Plated Spring SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating 1 amp Contact Resistance 100 milliohms max Bandwidth ? 9.3 GHz at -1dB Inductance 1MHZ at -0.02384 uH Captance 1MHZ at 1.06747 uF Specifications: Full Stroke 1.1 mm Rated Stroke 0.65 mm Spring Force 4 gf at load 0.65 mm Mechanical Life about 100000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Test Probe Pogo Pin SCPA020 for Integrated Circuit Inspection Semiconductor test probes are usually called double-ended pogo pins.  Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPA020 we will introduce is 0.2 mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. � Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold or gold clad phosphor bronze. The bottome plunger is made from SK4 plated with nickel and gold. The same is with the top plunger. The inner spring is made from SUS304 plated with gold and nickel. This probe pin could withstand the current up to 1 Amp. The typical maximal contact resistance is about 200 milliohms The plunger can be pressed at a distance of up to 1.1 mm. But it is better to be pressed at a distance of 0.6 mm at most in working environments. Otherwise the spring will probably be damaged severely under constanct pressure. When the plunger is pressed at a distance of 0.6 mm, the loaded force is about 12 gf, which fluctuates to a tolerane. For details, please check parameters in below table. Materials (plated) Barrel: Ph/ SP, Au on Ni Plated Bottom Plunger: SK4, Au on Ni Plated Top Plunger: SK4, Au on Ni Plated Spring: SWP  Au on Ni Plated Electronic Specification: Current Rating: 1 amp Contact Resistance: 200 milliohms max Bandwidth: 9.3 GHz at -1dB Inductance: 1MHZ at -0.13527uH Captance: 1MHZ at 0.186437uF Specifications: Full Stroke: 1.1 mm Rated Stroke: 0.6 mm Spring Force: 12 ±4 gf at load 0.6 mm Mechanical Life: about 100000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. Welcome to browse our website centalic.com and download any catalogs of our products.
Electronic Test Probe Double-sided Spring Pogo Pin SCPA057 for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. SCPA057 series is a medium-sized one in all semiconductor test probes. Both plungers are movable. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. Its parameters are as below. Materials (plated) Barrel: Ph, Au on Ni Plated Bottom Plunger: BeCu, Au on Ni Plated Top Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 3 Amps Contact Resistance: 100 milliohms, max Bandwidth: 5 GHz at -1dB Propagation Delay: 24 ps Inductance: 1MHZ at -0.03664 uH Captance: 1MHZ at -0.704638 uF Specifications: Full Stroke: 0.63 mm Rated Stroke: 0.5 mm Spring Force: 45 ±13 gf at load 0.5 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Semiconductor Test Probe Double-ended Pogo Pin SCPE015 for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPE015 is the tiniest series in semiconductor test probes since its outside diameter is only 0.15mm. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices  Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. Its parameters are as below. Materials (plated) Barrel: Gold Clad, No Plated X-Bottom (Plunger 1): Pd, No Plated Y-Top (Plunger 2): Pd, No Plated Spring: SWP, Au on Ni Plated Electronic Specification: Current Rating: 0.5 amp Contact Resistance: 250 milliohms max Bandwidth: 11.4 GHz@-1dB Inductance: 1MHZ@-0.06439uH Captance: 1MHZ@0.364375uF Specifications: Full Stroke: 0.8 mm Rated Stroke: 0.6 mm Spring Force: 9 ±2 gf@load 0.6 mm Mechanical Life: about 100000 cycles Company Information: Centalic Technology Development Ltd. was founded in 1980. Specializing in R&D, manufacture, sales and technical service, Centalic is one of the earliest high-tech enterprises which concentrates on large-scale production of various test probes and precision metal parts, and has a professional manufacturing base owning complete production lines and test equipment. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. If you need a complete set of product manual, please feel free to contact us. Many products are not uploaded due to a huge range. If you can't find what you need, please feel free to contact us. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
Cable Harness Contact Probe Pin CHL137 for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHL137 harness probe we will introduce here is 1.37 mm in diameter and 26.7 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 100 milliohms. It is suggested the plunger be pressed at a distance of 2.8 mm at most when this probe works, although the plunger can move as far as 4.2 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 2.8 mm, its loaded force is about 100 gf, namely 3.5 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 100 milliohms Full Stroke: 4.2 mm Rated Stroke: 2.8 mm Spring Force: 100 ±30 gf (3.5 oz) at load 2.8 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Flanges: slip on, welding neck/long welding neck, socket welding, threaded, blind/bossed blind, orifice, special flanges as per customer drawing, fasteners (socket head, set screw, counter sunk, button head, hexagonal head bolts & screws, hex nuts) washers, dowel pins (parallel pins, taper, knurled pin, spiral pin, grooved, clevis), guided bushing, friction grip bolt, cold forged components, gear shaft, spline shaft, kick shaft, ball pins, ball rods, shaft for alternator or stators, brake scam, piston pin, material grades like alloy steel 8.8, 10.9, 12.9, 45h, 14.9, 14k, stainless steel a1, a2, a3 & a4, 204, 410, 416, 431, 420, brass, aluminum v65/2024, titanium bt16, gears, timing belts, bearings, gaskets, o rings, seals, keys, grinding wheels and abrasive paper, welding rods, hexagonal wrench, a4 papers reams, tapes, corrugated sheets, boxes, cnc, vmc machine precision component(turning, milling, moulding & fixtures tools)..
Battery Contact Probe Test Pogo Pin BIP48 for Connector Application Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP48 series of battery contact probes. The outside diameter is usually 4.8 mm and total length is 6.8 mm. There are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 5.95 mm (235 mil) Current Rating: 5 Amps, continuous Contact Resistance: 30 milliohms (Maximum) Full Stroke: 2.15 mm Rated Stroke: 1.27 mm Spring Force: 23 gf (0.8 oz)/ 56 gf ( 2 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: Brass, Gold Plated semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Gold-plated Probe Pogo Pin PE100(90) Series for In-circuit Test In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PE100(90) series here. Its test center is 100 mil. The diameter is 1.36 mm and the total length is 34 mm. Various tip styles, for example, A, B, U, H, K, L, BK, etc., are available for test probes. There are roughly three types of receptacles, namely CR, SC and WW to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 2.54 mm (100 mil) Current Rating: 3 Amps, continuous Contact Resistance: 30 milliohms Mounting Hole Size: Diameter 1.75 mm Full Stroke: 6.5 mm Rated Stroke: 4.3 mm Spring Force: 284 gf (10 oz) Materials Receptacle: Brass, Gold Plated Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper, Nickel Plated or Gold Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Double-Sided Spring Pogo Pin Test Probe SCPC031 Applied to Chip Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPC031 we will introduce is 0.31 mm in barrel diameter and 6.7 mm in total length. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold. The bottom plunger is made from beryllium copper plated with nickel and gold. The top plunger is made from SK4 plated with nickel and gold. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 1.5 amps. The typical maximal contact resistance is about 150 milliohms. The plunger can be pressed at a distance of up to 1 mm. But it is better to be pressed at a distance of 0.65 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.65 mm, the loaded force is about 25 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Phosphor Bronze, Au on Ni Plated Bottom Plunger: Beryllium Copper, Au on Ni Plated Top Plunger: SK4, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 1.5 amps Contact Resistance: 150 milliohms max Bandwidth: 7.5 GHz at -1dB Inductance: 1MHZ at -0.05856 uH Captance: 1MHZ at 0.434274 uF Specifications: Full Stroke: 1 mm Rated Stroke: 0.65 mm Spring Force: 25�±5 gf at load 0.65 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Double-sided Spring Pogo Pin Test Probe SCPC058 for IC Test Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPC058 we will introduce is 0.58 mm in barrel diameter and 8.85 mm in total length. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold. The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from SUS304 plated with gold and nickel. This double-sided spring pogo pin could withstand the current up to 4 amps. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 1.2 mm. But it is better to be pressed at a distance of 0.8 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.8 mm, the loaded force is about 35 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Phosphor Bronze, Au on Ni Plated Bottom Plunger: Beryllium Copper, Au on Ni Plated Top Plunger: Beryllium Copper, Au on Ni Plated Spring: SUS304, Au on Ni Plated Electronic Specification: Current Rating: 4 amps Contact Resistance: 100 milliohms max Bandwidth: 9.3 GHz at -1dB Inductance: 1MHZ at -0.02158 uH Captance: 1MHZ at 1.4027 uF Specifications: Full Stroke: 1.2 mm Rated Stroke: 0.8 mm Spring Force: 35�±7 gf at load 0.8 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
