Exporter of all types and sizes of Fasteners.
Exporter of all types and sizes of Gaskets.
Exporter of angle, beam, channel, tmt bar, flat, sheet and plate.
Three way valve which design for diverting or mixing service applications. A diverting service valve takes common stream and splits it into two outlet force, this configuration is used for applications such as level control and pump bypass control valve. Mixing service valve combines two fluid streams and discharges the mixed fluid to a common outlet ports this configuration is used for applications where two fluids need to be mixed the end result can range from temperature control to producing a new fluid. Three way valve actually performs of two opposite acting standard two way valves. So that use of one valve instead of two is very economical. Valves are available with hand wheel if required. Size : 15 NB to 300 NB Rating : IBR approved ANSI Class 150, 300 , 600 , 900 , 1500 & higher on request Body Materials : Carbon Steel (A216 Gr WCB) / Alloy Steel (A217 Gr WC6) / SS (CF 8M) Leakage Class : ANSI B 16.104 CL IV Range Ability : 40 : 1
Our pressure relief safety valve is designed as a pop up type valve. On exceeding set pressure the valve opens to discharge the excess built up pressure. After relieving excess pressure, the valve automatically returns to the original position. The bronze internals (Seat & Plug) ensure that there is no leakage while in operation. By replacing only the spring it is possible to change set pressure range. Sizes Available : 15 NB, 20 NB, 25 NB, 40 NB, 50 NB End Connections : Screwed BSP IBR Certificate : Available For IBR Applications Soft-Seating : Also Available For Air Application Maximum Operating Temperature : 235° C Available Range : Min. Blow Off Pressure 0.35 Kg/Cm2 Max. Blow Off Pressure 17.5 Kg / Cm2
PRDS Valves ( Combined Pressure Reducing Cum Desuperheating Valves ) Features : Our combine PRDS valve is a single seated globe type valve that combines pressure & temperature reduction in one compact solution. The high pressure, high temperature steam which enters the main branch, is reduced in pressure and then spray water is injected immediately after pressure reduction. The high velocity and turbulent flow conditions data present immediately following the pressure reduction allow for rapid atomization and absorption of the spray water thus effectively desuperheating the steam. Reduction of noise level due to mist formation by water is an added advantage. Size : 15 NB to 300 NB Rating : IBR approved ANSI Class 150, 300 , 600 , 900 , 1500 & higher on request. Body Materials : Carbon Steel (A216 Gr WCB) / Alloy Steel (A21? Gr WC6) / 55 (CF 8M) Leakage Class : ANSI B 16.104 CL IV Range Ability : 40 : 1
Sizes Available : 15 NB, 20 NB, 25 NB, 40 NB & 50 NB. Class 800 Options : IBR OR Non - IBR. Material : Forged Steel Body With SS Internals End Connections : Screwed BSPT Socket Weld Butt Weld Max. Temperature : 427o C Max. Pressure 139 kg / cm2
DESCRIPTION: Neoprene rubber is a chloroprene rubber, which has excellent mechanical property & good abrasion resistance. It gives good resistance to oil & heat, ozone, sunlight & weather and also gives good adhesion to metal surface. Neoprene rubber sheets / rolls are available for a range of applications in the industries. Many grades of neoprene are available depending on the application. These rolls will handle most tough industrial environments and moderate to heavy alkaline and chemical resistive situations. It is manufactured in pure neoprene rolls, commercial, medium strength, High Strength, Cloth Inserted, Antistatic, Fire Retardant, and Textured & in Strips. The temperature ranges from (-30°C to +100°C) in operation condition. APPLICATIONS: Neoprene rubber sheets / rolls are mainly used in sealing applications in construction sites & sound studios, general & industrial applications like sealing, gasket & packing to avoid leakages of oil, heat, steam, water, air, acid & alkali. It is also used in marine applications. It has flame retardant properties & good resistance to inorganic chemical products. 100% NEOPRENE RUBBER SHEET: BLACK NO GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BNP-1445 1.4 45 60 350 2 BNP-1555 1.5 55 70 300 3 BNP-1665 1.6 65 70 250
DESCRIPTION: Nitrile Rubber is a copolymer of butadiene and acrylonitrile. Nitrile rubber sheets are mainly used as oil & solvent resistance as it has good tensile strength, low compression set, flexibility & impermeability to gases. These sheets are very good resistance to petroleum based products having recommended for operating temperature from (-20°C to +110°C). APPLICATIONS: These sheets / rolls are mainly used for sealing, gasket & packing to avoid leakages from oil, solvent, petroleum based fluids, lubricating oil, transformer fluid & sealing against gases. PROPERTY: Very good resistance to petroleum based fluid goods & high temperature resistance up to 110°C. Very low-level permeability to gases. Poor ozone resistance. 100% NITRILE RUBBER SHEET: BLACK NO GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BNT-1240 1.2 40 60 500 2 BNT-1350 1.3 50 70 450 3 BNT-1460 1.4 60 80 400 4 BNT-1570 1.5 70 80 300 COMMERCIAL GRADE NITRILE RUBBER SHEET NO GRADES NEOPRENE (%) DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BNTNR-50 50 1.6 65 20 250 PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 Store according to DIN 7716 standards. Products must be stored in cool, dry places with temperature ranging between 10°C to 30°C, sheltered from the sun & free from ozone for better shelf life. Avoid contact with acids & alkalies. If there is any doubt about the condition of sheet/roll, they should be retested before putting into service. Products should be issued in the order of their date of manufacture.
DESCRIPTION: EPDM rubber sheet / roll is very good weather-proof quality that makes highly recommended for the outdoor use, These sheets resist to oxidation, UV rays, Ozone, weathering & low temperature flexibility. The operating temperature range is from (-40°C to +130°C). EPDM rubber sheets / rolls are stable for long time due to its inert structure APPLICATIONS: EPDM rubber sheets are highly used for industrial & outdoor application like weather strips, drinking water applications, rain water sealing, protection against sunlight & heat gaining as a roofing membrane & acid resistance applications. Also useful as a liner in pulverizing system. PROPERTY: Very good resistance to water & water-based chemicals withstand temperature up to 130°C. Very good weathering resistance. Good resistance to mild acids, liquid fertilizer & break fluids. No resistance to oil & oil based products. 100% EPDM RUBBER SHEET: BLACK NO GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BEP-1155 1.1 55 70 500 2 BEP-1260 1.2 60 80 400 3 BEP-1365 1.3 65 100 300 4 BEP-1470 1.4 70 70 250 COMMERCIAL GRADE EPDM RUBBER SHEET NO GRADES EPDM (%) DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BEPNR-50 50 1.5 65 50 250 PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 RECOMMENDATIONS REGARDING STORAGE AFTER RECEIPT Store according to DIN 7716 standards. Products must be stored in cool, dry & dark places Avoid contact with hydrocarbons, solvents, acids & alkalies. If there is any doubt about the condition of sheet/roll, they should be retested before putting into service. Products should be issued in the order of their date of manufacture.
DESCRIPTION: Butyl Rubber sheet / roll are a very low permeability to air & other gases. These sheets have excellent resistance to sunlight, ozone & oxidation. The operating temperature resistivity ranges from (-30°C to +110°C). It is resistant to most inorganic products and best resistance to mineral acids & alkaline. APPLICATIONS: These sheets / rolls are used for Chemical tank lining, Pharmaceutical stoppers, Acid protective clothing & many more applications. PROPERTY: Very good resistance to acids & alkalis. Very good for low resilience applications like shock absorber & vibration dampers. Not recommended its use in applications where resistance to oils & hydrocarbons is required. NO GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BIIR-12560 1.2 55 80 350 2 BIIR-13065 1.3 60 60 300 3 BINR-60 (IIR: NR = 60:40) 1.3 65 70 350 PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 RECOMMENDATIONS REGARDING STORAGE AFTER RECEIPT Store according to DIN 7716 standards. Products must be stored in cool, dry & dark places with temperature ranging between 10°C to 30°C, sheltered from the sun & free from ozone for better shelf life. Avoid contact with hydrocarbons, solvents. If there is any doubt about the condition of sheet/roll, they should be retested before putting into service. Products should be issued in the order of their date of manufacture.
DESCRIPTION: Diaphragm Rubber sheets are manufactured by inserting 1 ply & 2 ply Nylon Fabric used as Diaphragms for wide variety of applications specifically for Oil, LPG & solvent resistant applications. Recommended use for control valves, regulators, pumps etc. Diaphragm sheet is manufactured with high quality Nitrile rubber compound designed for long service. This rubber sheet is reinforced with multi-ply fabric to provide desired strength. The purpose of providing insertion is to provide additional strength to material in order to make it more pressure proof. Selection of fabric is available on request. NO GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BDR-1370 1.3 70 80 300 PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 RECOMMENDATIONS REGARDING STORAGE AFTER RECEIPT Store according to DIN 7716 standards. Products must be stored in cool, dry & dark places with temperature ranging between 10°C to 30°C, sheltered from the sun & free from ozone for better shelf life. Avoid contact with acids & alkalies. If there is any doubt about the condition of sheet/roll, they should be retested before putting into service. Products should be issued in the order of their date of manufacture.
Stainless Steel Hoses and Hose Assemblies Stainless steel corrugated flexible hoses are offered from 6mm (1/4’) to 300 mm (12’). The annular corrugated hose body provides the flexibility and pressure tight core of the assembly. Lance Hoses An import substitute product, developed and manufactured by us. These hoses distinguish themselves due to their good performance in adverse and hostile conditions. These ultrasonically cleaned and degreased hoses are pressure sealed, leak proof under vacuum condition and can be used with or without inside interlocked liner. Advantages of Flexible Metal Hose - Suitable for wide temperature range (-270°C to700°C). - Compensates for thermal expansion contraction in the piping system. - High physical strength. - Fire resistant. - Moisture resistant. - Longer life. - Good corrosion characteristics. - Resistant to abrasion, penetration and damage. - Connects misaligned rigid piping absorbs or dampens vibration and similar equipment. - A flexible and quick option for rigid piping in difficult locations. The fitting are available in Mild Steel, Carbon Steel, Stainless Steel, Brass, Gun Metal, Rolled bronze. Flange connection with fixed & floating flanges to meet IS, DIN, ANSI* ASA standards or as per customer's specification.
Product Details: Size 1/2 inch, 3/4 inch, 1 inch, 2 inch, 3 inch Range & Specifications : Socket Weld : 1/2 to 2 " upto 9000# 3" - 3000# Screwed : 1/2 to 2 1/2' upto 6000# 3" upto 3000# List of Specifications : 1. ANSI/ASME B16.11 Forged- Fittings, Socket Welding & Threading. 2. ANSI B1.20.1 Pipe Threads, General Purpose 3. ASTM A105, A182, A234, A350, A262, A153.
Product Details: Size 1/2 inch, 3/4 inch, 1 inch, 2 inch Forged Nipples Range : Socket Weld : 1/2 to 4 " upto XXS/6000# Screwed : 1/2 to 4" upto 6000# List of Specifications : 1. ANSI/ASME B16.11 Forged- Fittings, Socket Welding & Threading. 2. ANSI/ASME B16.9 Factory- Made Wrought Steel Butt Welding fittings. 3. BS 3799 Steel Pipe fittings, Screwed & Socket Welding for the petroleum industry. 4. ANSI B1.20.1 Pipe Threads, General Purpose 5. ASTM A105, A182, A234, A350, A106, A335, A262, A312, A153.
Brass Round Bar is commonly used in electrical application, high strength tooling material and ornamental decoration. Moreover, there is a large variance in alloy composition giving Brass Round Bar an enormous variety of purposes and possibilities.
Our organization is a leading supplier of Aluminium Flat Angle. The material for track is Aluminum. Conductors shall be accurately aligned to ensure positive electrical contact between the collector and the conductor.
25A contact switching capability. Contact Form: 1B/1C optional Only impulse excitation needed, Single coil and dual coil optional. Low power consumption, strong load capability. Small in size, PCB type installation. 4KV dielectric strength between coil and contacts. RoHS compliant. Outline dimensions: (38.8 x 28.7 x 15) mm. VDE certificate No.: 40039308.
We are engaged in providing optimum quality Copper Elbow that is an important part widely used in refrigerator and air conditioner. The Copper Elbow is manufactured by using high-grade copper metal as it is a ductile metal that features extremely high thermal and electrical conductivity. The Copper Elbow is designed in 90 angle that is used for joining different other parts such as pipes, at various angles. Highlights : Superior quality High performance High thermal and electrical conductivity Resists dezincification Available Sizes : From 14 to 5.18 & from 10mm to 133mm
Electrical & electronic equipment.