1 All-in-one design, high integration and space saving installation 2 Using high-performance lithium iron phosphate cells, laser welding, good cell consistency, designed service life of more than 10 years 3 Charging and discharging are controlled separately, which is convenient and reliable to control charging and discharging. The discharge port will not be disconnected when over-charging, and the charging port will not be disconnected when over-discharging, the system has good stability 4 Master-slave mode, passive equalization, can manage the equalization resistance, can set the equalization start voltage difference, and monitor the equalization resistance temperature, more intelligent and safe, and reduce the impact of barrel effect on system energy storage 5 BMS adopts NXP(USA) automotive-grade high-performance chips, with strong anti-interference, good reliability and wide temperature range 6 CAN2.0 communication interface, has the advantages of strong real-time performance, long transmission distance, strong anti-electromagnetic interference ability 7 System parameters can be set through the host computer, such as fan start/stop temperature, charger maximum current setting, charge and discharge current correction, SOC correction, with insulation leakage detection function to prevent oil leakage and short circuit of the cell 8 Integrate Solar charge controller or AC charger optional, BMS communication control, more safe and reliable; 9 Cell temperature management, can be automatically controlled with the air conditioner heater according to the cell condition to make the cell works at the most suitable temperature, and can be linked with the fire protection system as needed Performance characteristics 10 Accurately estimate the state of charge of the battery pack, that is, the remaining power of the battery, to ensure that the power of the battery pack is maintained within a reasonable range 11 Built-in BMS management system with comprehensive protection and monitoring control functions 12 5" LCD screen display, easy to operate, can check the temperature, voltage, working status, discharge current, dynamic and static SOC algorithm of a single cell, local display of alarm info, alarm level distinction, accurate positioning of abnormal cells 13 Main control MCU can be centrally controlled and manage peripheral settings (AC charger, inverter, solar charger) to adjust the charging current and voltage of peripheral devices according to the battery charging curve, making the system more reliable
An open loop system is for climates where there is no risk of freezing. Recirculation freeze protection can be provided by the recirculation feature in the controller. An open loop water heating system provides many advantages. It is the simplest and typically the least expensive active system to install. There is no heat exchanger, which allows efficient heat transfer directly to the water. The system operates at standard line pressure. It is simple to add capacity to the system if demand changes. The system integrates easily with existing systems.
1. Inner tank: Import stainless steel SUS304-2B food grade; thickness:1.2mm 2. Outer tank: galvanized steel/Stainless steel SUS201, thickness: 0.4mm. 3. Vacuum tube: heat pipe 58x1800mm 4. The material of insulation:High-density polyurethane integrated foam-forming layer 50mm thickness 5. Frame(Bracket): galvanized steel/Stainless steel 6. Angle: As customer requirement 7. Heat preservation: 72hrs
Products model: sc-s01p»G+dåseparate pressurized solar water heaterp»G+GǦ Products intro The separate pressurized solar water heater compose of solar collector, storage tank, controller, working station and installation parts. Working principle: 1) when the discrepant temperature of the solar collector and water tank reaches the set value, the controller shall start the circulation pump automatically 2) the circulation pump makes heat-conducting liquid circulate automatically 3) the heat-conducting liquid transfers heat to water by heat exchanger in the water tank 4) in case the temperature of the water tank does not reach tmax, then start the auxiliary heating device 5) if discrepant temperature of the collector and the water tank does not reach the set value, the circulation pump shall be shut automatically Feature: 1) collector separates with the storage tank. The tank can be put anywhere of the house 2) and the collector can be put on both tilted roof and flat roof 3) module design, arbitrary combination, harmony with the building perfectly 4) intelligent control and automatic operation 5) anti-freeze: no water inside the tubes when it works 6) the system controller has the anti-freezing function is that the temperature circulation will operate while it reaches the fixed temperature 7) multifunction: bathing, washing, domestic heating 8) workable at anytime and enjoyableouter Features of separate pressurized system: * strong hydraulic pressure makes your bathe more comfortable * modularized collector, arbitrary combination * intelligent controlling and multiple functions * arbitrary combination with structure of your beautiful constructions * separate installation conveniently * working with assistant resource * full set of original equipment, the life time will be much longer to ensure better using * material A) inner water tank: imported sus304 stainless steel B) outer water tank: galvanized steel alloy C) bracket: aluminium alloy
Separated pressure solar water heater This system is combined with solar collector, pressurized storage tank, work station, pipeline etc. 1. Solar collector can be the heat pipe solar collector, the u pipe solar collector, the balcony solar collector or the flat solar collector. 2. Inner tank for pressurized storage tank can be sus304-2b, ss316l or enamel tank. 3. Solar working station. 4. Working pressure :0.6mpa , testing pressure :1.0mpa Characteristic: 1. No disorder water tank on your roof: split solar water heating systems is using a high efficiency solar collector on your roof and a high pressurized storage tank in the house. Integrated in to the roof of the building perfectly. 2. Perfect solar collector for domestic hot water heating system can be combined with existing energy source, such as your gas water heater, electric water heater, boiler, etc. 3. There is an auxiliary heating device--electric heater booster in the tank, so providing hot water in case of cloudy or rainy days, you will no need to worry about it. 4. Completely automatic
Product : Valves Brand : Renaissance Pipe Fitting Inc. Sizes : Refer the specification Condition : New Rating : 4.6, based on 112 reviews price : Start from 5 USD RFP India is Indias wellknown manufacturer supplier and exporter of Valves which is a device that regulates directs or controls the flow of a fluid gases liquids fluidized solids or slurries by opening closing or partially obstructing various passageways Valves are technically valves fittings but are usually discussed as a separate category In an open valve fluid flows in a direction from higher pressure to lower pressure It is being made up from different materials like Stainless Steel Carbon Steel Alloy Steel Gun Metal Brass Bronze Forge Cast Iron Cast Steel and Mild Steel Meanwhile Valves are quite diverse and may be classified into a number of basic types such as Ball Valve Butterfly valve Ceramic Disc valve Check valve Choke Valve Diaphragm valve Gate valve Globe valve Knife Valve Needle Valve Pinch Valve Piston Valve Plug Valve and so on
What is Solar Water Pump : It's a Cost-effective, Reliable and Green solution for providing Water to remote locations where Electrical Supply is not available. It works by converting available solar energy to electrical energy and there by running motors coupled with pumps with that to lift underground water / to pump from sources like Underground water tanks ,Rivers and Lakes. Description : We deal with Solar pumps of various types ranging from 3 H.P. to 20 H.P. capacities Solar PV Cells / Modules are generally installed along with Water pump , Pump Controller / Drive (VFD) forms the whole system Remote operation through mobile application is also available Solar Modules can also be used to cover underground water tanks so that water temperature will also be maintained Types of Solar Water Pumps : Based on Function : Submersible Solar Pumps : These are designed to operate underwater They are used to Pump water from undergrounds/wells / underground water tanks Surface Solar Pumps : These are designed to operate on/ from the surface level of water These are generally used to pump water from shallow wells/rivers / lakes Based on type of Electrical Supply : AC Solar Pumps: These are designed to operate on AC (Alternating Current ) instead of DC (Direct Current ) These are generally used in applications where high flow rate and high-pressure output are required DC Solar Pumps: These are designed to operate on DC (Direct Current) These are generally used in applications where low flow rate and low-pressure output are required Applications : Agriculture Domestic Water Supply Community Water Supply Livestock Management Swimming Pools Hotels Fountains & Waterfalls Chiller Plants Ice Plants Concrete / Batching Plants Food Processing Plants Warranty Terms: Solar Modules come with a warranty of 15 years and an efficiency guarantee of 25 years Pumps and controllers warranty varies from 2-5 years based on the type and capacity of pumps
The heat collectors and the water tanks are connected perfectly, the heat which the panels collected will be stored in the water tank, it guarantees 24 hours per day to provide the hot water, and the system can work even under the -30 degrees. It can supply with a few tons even more water, is an ideal hot water supply system. It is applied to the big hotels, restaurants and other large places. 1: The water tank should be placed higher than the heat collectors, while the models are isolated types and the heat collectors are not pressure-enduring; The water recycled freely by the height difference between the water tank and the heat collectors. 2: The water tank should be placed lower than the heat collectors, while the models are isolated types and the heat collectors are pressure-enduring, the water is recycled by the water pump between the water tank and the heat collectors, the specific pressure-enduring models, please see the information of the pressure-enduring models on the web.
Main matter in this product page: We Manufacture , Supply , Install highly efficient Solar Street Lights of two categories : Solar Integrated / Solar All-in-one Street Lights : These are Solar All-in-one lights which means LED s , Solar Panel , Lithium (LFP) battery , Charge controller , BMS ( Battery Management System) , PIR (Motion Sensor) are inbuilt in one single unit Ranges available from 15 watt to 100 watt Solar Semi Integrated lights : These are Solar Street lights on which Solar Panels are mounted separately on top of pole with help of mounting frame and remaining components like LED s , Lithium (LFP) batteries , Charge Controller , BMS ( Battery Management System) are kept in one single unit . Ranges available from 15 watt to 60 watt Description / Features : No External power supply from DG set / EB line is required to run these lights they are completely self powered Comes with 5 years complete warranty including battery pack They come with back up of 18-20 hours a day and designed to operate in all climatic conditions with minimum back up time of 14-15 hours a day. No External cables required cable cost will be completely saved Saves Fuel cost / Energy cost these assemblies generally gets breakeven in less than 2 years Auto Dusk to Dawn Operation is programmed Auto On-Off of lights sensing ambient light Equipped with highly efficient LiFePo4 Lithium batteries and they has cycle life of 5000 cycles Highly efficient and tier 1 grade MONO PERC Solar Modules are used PIR (motion) sensor can be equipped as per requirement and they sense motion from distance of 10 meters. Completely safe to use at construction sites since no cabling and cable routing are required and they are complete DC systems . Warranty : All components of Solar Street Lights comes with 5 years complete warranty including that of battery pack Applications : Stock Yards / Storage Yards Site Offices Corporate Offices Residential projects , Layouts Gardens , Parks Shopping malls Parking Toll Plazas Highway Lighting Streets Lighting Re-walls construction sites Bridges Structural Construction sites
Main matter in this product page: We Manufacture , Supply , Install highly efficient Solar Street Lights of two categories : Solar Integrated / Solar All-in-one Street Lights : These are Solar All-in-one lights which means LED s , Solar Panel , Lithium (LFP) battery , Charge controller , BMS ( Battery Management System) , PIR (Motion Sensor) are inbuilt in one single unit Ranges available from 15 watt to 100 watt Solar Semi Integrated lights : These are Solar Street lights on which Solar Panels are mounted separately on top of pole with help of mounting frame and remaining components like LED s , Lithium (LFP) batteries , Charge Controller , BMS ( Battery Management System) are kept in one single unit . Ranges available from 15 watt to 60 watt Description / Features : No External power supply from DG set / EB line is required to run these lights they are completely self powered Comes with 5 years complete warranty including battery pack They come with back up of 18-20 hours a day and designed to operate in all climatic conditions with minimum back up time of 14-15 hours a day. No External cables required cable cost will be completely saved Saves Fuel cost / Energy cost these assemblies generally gets breakeven in less than 2 years Auto Dusk to Dawn Operation is programmed Auto On-Off of lights sensing ambient light Equipped with highly efficient LiFePo4 Lithium batteries and they has cycle life of 5000 cycles Highly efficient and tier 1 grade MONO PERC Solar Modules are used PIR (motion) sensor can be equipped as per requirement and they sense motion from distance of 10 meters. Completely safe to use at construction sites since no cabling and cable routing are required and they are complete DC systems . Warranty : All components of Solar Street Lights comes with 5 years complete warranty including that of battery pack Applications : Stock Yards / Storage Yards Site Offices Corporate Offices Residential projects , Layouts Gardens , Parks Shopping malls Parking Toll Plazas Highway Lighting Streets Lighting Re-walls construction sites Bridges Structural Construction sites
Main matter in this product page: We Manufacture , Supply , Install highly efficient Solar Street Lights of two categories : Solar Integrated / Solar All in-one Street Lights : These are Solar All-in-one lights which means LED s , Solar Panel , Lithium (LFP) battery , Charge controller , BMS ( Battery Management System) , PIR (Motion Sensor) are inbuilt in one single unit Ranges available from 15 watt to 100 watt Solar Semi Integrated lights : These are Solar Street lights on which Solar Panels are mounted separately on top of pole with help of mounting frame and remaining components like LED s , Lithium (LFP) batteries , Charge Controller , BMS ( Battery Management System) are kept in one single unit . Ranges available from 15 watt to 60 watt Description / Features : No External power supply from DG set / EB line is required to run these lights they are completely self powered Comes with 5 years complete warranty including battery pack They come with back up of 18-20 hours a day and designed to operate in all climatic conditions with minimum back up time of 14-15 hours a day. No External cables required cable cost will be completely saved Saves Fuel cost / Energy cost these assemblies generally gets breakeven in less than 2 years Auto Dusk to Dawn Operation is programmed Auto On-Off of lights sensing ambient light Equipped with highly efficient LiFePo4 Lithium batteries and they has cycle life of 5000 cycles Highly efficient and tier 1 grade MONO PERC Solar Modules are used PIR (motion) sensor can be equipped as per requirement and they sense motion from distance of 10 meters. Completely safe to use at construction sites since no cabling and cable routing are required and they are complete DC systems . Warranty : All components of Solar Street Lights comes with 5 years complete warranty including that of battery pack Applications : Stock Yards / Storage Yards Site Offices Corporate Offices Residential projects , Layouts Gardens , Parks Shopping malls Parking Toll Plazas Highway Lighting Streets Lighting Re-walls construction sites Bridges Structural Construction sites
Structure of solar collector: 1. Manifold 2.F58mm heat pipe tube 3.Side track 4.Bottom track 5.Feet holder Characteristics 1.Water is rapidly heated by the heat pipe. 2.There is no water in the vacuum tube, so the tube will not break in cold climate. 3.The small size of the collector allows for versatile architectonic integration. 4.Collectors can be combined with existing pipeline. 5.The collector can operate even in case of a broken tube. A single tube can, if necessary, be exchanged without interruption of the heating cycle. Type: jt58/1800-20 ac/sc Aperture area (m2) : 1.872 Vacuum tube qty (pcs) : 20 Vacuum tube size: f58*1800 mm Dimension: 2000*1600*130 Gross weight (kg) : 77 20gp/40gp/40hc loading qty(sets) : 82/164/200 Remark: Inlet and outlet: 22mm Testing pressure: 1 mpa Working pressure: 0.6 mpa Stagnation temperature: 200 ? Distance between tubes: 75 mm Installation angle: 15-75 degree Warranty: 5 years Paymant: t/t, paypal, l/c at sight Packing: standard box/ carton box Transportation: after payment 15-20 days at sea / airplane
Skylight Evacuated Tube Specifications: 1. Length (nominal):1800mm/1600mm 2. Outer tube diameter: 58mm/47mm 3. Inner tube diameter: 47mm/37mm 4. Glass thickness:1.8mm/2.0mm 5. Thermal expansion: 3.3x10-6í¦C 6. Material: Borosilicate Glass 3.3 7. Absorptive Coating: Graded Al-N/Al 8. Absorptance: v>93% (AM1.5) 9. Emittance:
Solar keymark Solar collector Reliable, efficient, twin-glass solar tubes heat pipe Copper heat pipes for rapid heat transfer Corrosion resistant brazed copper header Fetures: 1) length: 1800mm; thickness: 0.8mm 2) the manifold: Made of red copper Conducted by heat transfer medium liquid 3) the out casing: Made of aluminum alloy mold material of high-strength with air flow design 4) water can't flow into vacuum tubes 5) resistant to high-pressure( 6bars) 6) resistant to extremely cold or hot environment 7) no harm or pollution, environment protective, clean, healthy Economic, invest once and benefit for ever 8) to assemble many collectors together for the solar central heating project of the hotel and factory are permitted. Modelabsorb a rea (m2)heat pipesupply hot water (l/)qty. Per 20/40 container (set) Diameter(mm) length (mm) no. (pcs) Free/j-1800/58-181.4458180018150/6084/175 Free/j-1800/58-201.6058180020175/6077/160 Free/j-1800/58-241.9258180024220/6064/133 Free/j-1800/58-302.4058180030260/6052/106 Whole packaging
Specification: Manifold box: inner tank: stainless steel 304-2b, 0.4mm. Outer tank: stainless steel or galvanized steel. Frame: profile stainless steel, 1.2mm or more, or galvanized steel, 1.2mm or more. Types of tubes: 47-1500, 58-1800, or other types. No. Of tubes: from 10 tubes to 50 tubes. Characteristic: High efficiency, low cost Suitable for project or home use No pressure at all, very safe easy installation Beautiful outlook, match the building perfectly large absorbing area
Features: * Choose applicable non-pressure manifolds according to different demands. * From family to factory; from tens to hundreds to thousands, it is widely used in hotels, schools, armies and factories. * Automatic supplying water, electric heat, recycling and protection. * Investment only once, benefit forever. * No harm, no pollution, save an clean Key specifications: * Material: stainless steel or Anodized aluminum * High-performance evacuated tube design. Up to 75% efficient a) Size: 47 x 1,500mm / 58 x 1,800mm b) Qty: 15 / 20 / 25 / 30pcs c) Hail resistance: diameter 25mm * Temperature conservation layer in chest a) 30mm thickness imported polyurethane, machinery overall for keeping the same temperature and high pressure foam b) Heat preservation: 72 hours * ISO9001:2000 / CE/CCC certificate * 3 years international responsibility for free repairing or exchange due to original quality problems * Packing: export carton and foam
Working principle: * combined many collectors with water storage tank as complete projects, heat pipe in solar vacuum tube for heat transferring, by circulation pump and relative system to make transfer medium liquid take the heat to water tank. Key specifications: * solar vacuum tube with heat pipe A) size: 47 x 1, 500mm / 58 x 1, 800mm B) qty: 15 / 20 / 25 /30 C) hail resistance: diameter 25mm * material: stainless steel or anodized aluminum * temperature insulation layer in chest A) 30mm thickness imported polyurethane, machinery overall for keeping same temperature and high pressure foam B) heat preservation: 72 hours * max pressure bearing: 0.8mpa * 3 years international responsibility for free repairing or exchange due to original quality problems * packing: export carton and foam
1. Blocking design, easy assembled 2. It can be mounted sloping roof and wall without frame 3. The pipeline is made of red copper and conducted by heat transfer medium liquid; water can't flow in the vacuum tubes and is operated when confined 7 layers thicken cartons
Solar collector The characteristic: 1 the vacuum tubes absorb the solar energy and transfer into the heat energy, then pass it to the u pipe, it can get high temperature. 2 there is no water in the vacuum tube, so the tube will not break in the winter. 3 it is steady and credible. 4 it can be combined with the architecture perfectly. 5 it can be combined with existing pipeline. 6 it can still operate in the event of occasional tube breakages. The details of material: Outer tank: alnico 1.5mm Manifold: 22mm thickness 2mm U copper type: 8mm thickness 0.6mm G.W. 50.6kg
Solar collector The characteristic: 1 The water is heated by the heat pipe rapidly. 2 There is no water in the vacuum tube,so the tube will not break in the winter. 3 It can be combined with the architecture perfectly. 4 It can be combined with existing pipeline. 5 It will be affected by the local water quality,it doesnf+t suit hard water. 6 It can still operate in the event of occasional tube breakages. The details of material Outer tank: Alnicof¼1.5mm Manifold:fT22mm thickness 2mm g.w. 77.1kg
