Gve(e1, g.703 to v.35, v.24 converter) Gve(e1, g.703 to v.35, v.24 converter) Detailed selling lead description Features: 1) v-gve is an asic-based converter using one e1/g.703 to convert to v.35 2) can convert successive n x 64k (n=1-32) data stream into pcm signal of e1, the data rate is up to 2048kbps 3) placed in e1 frame, data user just needs necessary timeslot 4) setting timeslot is continuous and according to rate of data port 5) the data ports have v.35 and v.24/rs232c which are optional 6) the ports support external clock and become linking end line 7) v-gve satisfies the requirements of g.703, g.704&g.706 of itu 8) v-gve has local and remote loop backs. Therefore user can use circuitry-test and malfunction diagnose conveniently Detailed product description Features: 1) rate of data transition: n x 64kbps (n=1-31), 2, 048kbps 2) transmission mode: synchronization 3) line interface: impedance 75 ohm, physical interface bnc; impedance 120 ohm, physical interface rj45 4) transmission features: comply with g.703 5) clock: line; external 6) testing method: local analogy loopback, remote digital loopback 7) dce interface: v.35 or v.24/rs232c 8) power supply: 220v f+ 10%, 50hz; 48v dc (optional) 9) power consumption: 5w 10) volume (l x w x h): 225 x 145 x 40mm; 9" x 5.8" x 1.6" 11) temperature: 0 - 40fpc 12) humidity: 0~95%
L-signal measurement, and industrial-site signal isolation and long-term transmission and so on. Products include power supply isolation, signal isolation, linearization, a/d conversion and rs-485 serial communication circuit module. Each serial port can connect maximum 256 pcs of isoad series modules, means of communication using character communication protocol or modbus rtu communication protocol. Its instruction set compatible with the adam modules, the baud rate is set by the user, with other manufacturers control module hanging in the same rs-485 bus, to facilitate host programming. Iso ad series of products are based on single chip of intelligent monitoring and control systems, all the user sets such as the calibration value, address, baud rate, data format, checksum status and other configuration information is stored in nonvolatile memory eeprom inside. Isoda series of products according to industry standard design, manufacture, signal output / communication interface isolation, can withstand 3000vdc isolation voltage, anti-interference ability, high reliability. Operating temperature range: - 45 ~ +80. Model selection Isoad16 u(a) - Vin/iin U1: 0-5v a1: 0-1ma U2: 0-10v a2: 0-10ma U3: 0-75mv a3: 0-20ma U4: 0-2.5v a4: 4-20ma U5: 0-¡¨¤ 5v a5: 0-¡¨¤ 1ma U6: 0-¡¨¤ 10v a6: 0-¡¨¤ 10ma U7: 0-¡¨¤ 100mv a7: 0-¡¨¤ 20ma U8: customized a8: customized Communication interface 485: output is rs-485 interface 232: output is rs-232 interface Dimensions:58*87.5*59mm
Media Converter, 10/100M 1310nm SM 5km Fiber optic media converter Skype:wirenettehnology Features : Surporting : Full duplex and half duplex transmission and capable of automatic negotiation. efficient builtin switching core ,to implement flow control and reduce broadcast packets. Surporting : The transmission of extra-long packes over VLAN Surporting : The selection of mutiple types of fiber ports such as dual-fiber multi-mode .dual-fiber single mode and single fiber single mode, to satisty the extended requirements of users. Technical specifications Parameter Specifications Access mode 10/100Mbps Standard IEEE802.3 10Base-T Ethernet,IEEE802.3u,100Base-TX/FX Fast Ethernet, IEEE802.3x Flow control,IEEE802.1q VLAN,IEEE802.1p QoS,IEEE802.1d Spanning Tree Wavelength 850nm/1310nm/1550nm Transmission distance Dual-fiber multi-mode: 2Km; dual-fiber single-mode: 25/40/60/80/100/120Km; single-fiber single-mode: 25/40/60/80/100Km Category-5 twisted pair: 100m Port One RJ45 connector, connected to STP/UTP category-5 twisted pair One fiber port: Multi-mode - SC or ST (fiber size: 50,62.5/125¦m) Single mode - SC/FC fiber port (fiber size: 9/125¦m) Single-fiber single-mode - SC/FC fiber port (fiber size: 9/125¦m) Conversion mode Medium conversion, storing and forwarding MAC address table I K Buffer space 1Mbit Flow control Full duplex state: flow control; half duplex state: back pressure mode Delay 9.6us Bit error rate
Serial to ethernet converter (rs232/rs485).
5000 series ethernet/usb and rs 485/232 remote control modules, 8000 series rs 485 digital and analog i/o remote control modules, 8500 series rs 485, rs 422 and rs232 communication sereis, 9000 series ethernet remote control modules.
Features: -Broadcast filtering, address auto learning and auto-update feature and th operating mechanism of store and forward. -Cache size: 256KB, address table size: 4KB -Ethernet 10Base-T or 100Base-TX or 1000Base-T to 1000Base-LX fiber optic media converters -Support IEEE 802.3, IEEE 802.3U, IEEE 802.3X, IEEE 802.3z/AB, IEEE802.1d -Supports full-duplex or half-duplex backpressure flow control flow control, and with Auto-Negotiation function -Interface supports 1000Mbps, 100Mbps, 10Mbps, can use with notthe same rate. -TX/RX dual-header Standard SC interface -Electronical interface supports 10Mbps, 100Mbps, 1000Mbps -Automatically adapt , optical interface work rate 1000Mbps port -Integration of high-quality photovoltaic modules to provide good optical properties and electrical properties to ensure reliable data transmission -Status LEDs on link/connection status, dynamic data transfer/ full duplex / half duplex/rate status. -Provides one RJ-45 interface supports auto-electrical cross connect switches, hubs -Power Consumption: 4.5 W (Power adapter input AC-85V~ 265V) -Over 50,000 hours consistent working period. Transmission fiber: Multi-mode: 50/125, 62.5/125 or 100/140166;204;m Single-mode: 8.3/125, 8.7/125, 9 / 125 or 10/125166;204;m Operating temperature :0-50 161;227; C Storage temperature: -40-70 161;227; C Humidity: 5% -90% non condensing.
USR-TCP232-410S is a dual serial RS232 RS485 Ethernet converter, which is based on TI Cortex-M4 solution & integrated TCP/IP protocol stack. Basic Function of RS232 RS485 Ethernet Converter Industrial Solution: TI Cortex M4 Solution, -40~85C Web Server: Web socket/ Web to Serial Modbus Gateway: Modbus RTU to Modbus TCP / Modbus Pollinig Flow Control: CTS/RTS, XON/XOFF 2 Network links, each serial supports sending data to two target servers Network Printing N series supports hardware watchdog, never crash Basic Feature of RS232 RS485 Ethernet Converter Multiple indicator lights for convenient debugging Power-line terminal for industrial application ARM kernel and TCP/IP protocol stack Auto-MDI/MDIX,RJ45 port with 10/100Mbps TCP Server,TCP Client,UDP,UDP Server and HTTPD Client work mode Two ports can work independently at the same time Support virtual serial port and provide corresponding software USR-VCOM Serial baud rate from 600bps to 230.4K bps;Check bit of None,Odd,Even,Mark and Space DNS and DHCP supported Provide PC TCP/IP SOCKET programming example,VB,C++,Delphi,Android,IOS Built-in webpage;also can customize webpage for users Reload button,one key to restore default settings RJ45 with Link/Data indicator light,built-in isolation transformer and 2 KV electromagnetic isolation The global unique MAC address bought from IEEE,user can define MAC address Upgrade firmware via network Keepalive,rapidly detect dead links Support account and password,can be used to page login and network settings Support one channel Websocket,realize bidirectional transparent transmisison bewteen webpage and serial 0 Support UDP broadcast function,send and receive data from all ip in the network Ethernet Serial Converters Application Field Industrial data transmission, industrial automation security and protection monitoring, public security Smart home, power control, environmental monitoring, intelligent agriculture Door check on work attendance system, POS system, rice selling system Building automation system, power monitoring, self-service banking system, telecom machine room monitoring
LNK-IMC1100-SFP is a microtype media converter that supports external SFP modules and meets EN55022. It is an industrial product whose operating temperature range is -40℃ to 80℃. LNK-IMC1100-SFP supports 100M Ethernet port and 100M SFP port. The Ethernet port supports both half-duplex and full-duplex mode. LNK-IMC1100-SFP is the same at the transmitter or receiver sides. Users can use different type of SFP modules (single-mode/multi-mode fiber, 1/2 core) as needed. This Sleek Microtype design media converter occupies limited space and it's an ideal solution for easy installation within most camera housings. Ethernet Standards: IEEE802.3u 100Base-TX/FX IEEE802.3x Flow Control Processing Type: Forward Half-duplex, Full-duplex Forward Filter Rate:: 148,800pps (100Mbps) Cabling: 100Base-TX: Cat5 or above Maximum Distance: Cat5 UTP up to 100m Connector: 1x RJ45 Optical Port: 1 x SFP 100Base-FX Environmental Operating Temperature: -40°C to 80°C (-40°F to 176°F) Storage Temperature: -40°C to 85°C (-40°F to 185°F) Relative Humidity: 5% to 95% non-condensing MTBF: > 300,000 hrs Electrical and Mechanical Input Power: 12VDC (Terminal Block) Power Consumption: 2.4W Max. 0.2A@12VDC LED Indicators Power: Power Status 100TX: Link/Activity, Speed SFP: Link/Activity Dimensions (WxDxH): 36.2 x 117 x 24.5 mm Weight: 0.15Kg Casing: Aluminum Case Mounting Options: Wall-mount / LNK-MR-C10 1U Rack Regulatory Approvals ISO9001, CE, FCC, RoHS FCC part 15,Class A EN55022:2006+A1: 2007 Class A Surge Protection: RJ45: 1KV Power: 500V ESD: 4KV/8KV Standard Packaging: Carton packaging(Support customer Logo)
Contact: amily[at]veecom dot com dot cn GVE-Tplus is an upgrade of GVE-T. It is based on the ASIC circuitry design technology. It is a multi-functional, multi-purpose E1/G.703 to V.35 and LAN three-in-one multiplexer, which is also knowns as the three-in-one interface converter. GVE-Tplus can not only be set up into GVE-T, but also can distribute the whole E1 capacity to V.35 data interface, although E1 must be framed N*64Kbps(N=1--31). The work mode can be either internal clock and slave-clock, or N*64Kbps(N=1--31) external clock to achieve end-linking line. GVE-Tplus can be set up into long-range Ethernet bridge from V.35 to LAN interface. With low cost, it is suitable for use in bridge connection which is sensitive to cost or use in LAN as a stretcher or subsection. It can learn automatically MAC address in the connected LAN and only transmit the aim address to frame in another LAN. There are more than 10000 addresses in its LAN table. And they can be updated automatically. The highest speed of filtrating and transmission is 30000 frame/second(line speed). The buffer size is 64M. The throughput delay is 1 frame. When it is used as a stretcher or subsection, it can forbid filtration so that all traffic can be broadcasted in WAN. 10baseT interface can run in full duplex Ethernet with topology and improve data throughput by eliminating filled blanks in the 64 bytes frames. Without any negotiation in V.35 port, it is specially suitable for use in satellites and other wireless broadcast. 245mm*215mm*50mm
Overview: GVE-Tplus is E1 to V.35/V.24/RS232 and Ethernet Converter. Other series interface RS449/RS530/X.21 also can be optional. E1 port can support BNC/75ohm and RJ45/120ohm optional. This device provides an economical digital access solution for E1 and fractional E1 network services. With a adapter cable, the device can connect to other DTE device, such as router, at data rates of 64Kbps to 2048Kbps.User data is placed into the E1 frame, using only the required number of timeslots, timeslot assignment is accomplished according to the data port speed and manual setting of DIP switches. The V.35 or V.24/RS232 and Ethernet share the 2Mbps bandwidth, the total bandwidth of the 2 interfaces must be not more than 1984Kbps.GVE-Tplus is widely used in communication network, both in WAN and LAN connection field. Features: *Comply with ITU V.35, G.703, G.704, G.706, G.823 *Full comply with IEEE 802.3 /IEEE 802.1Q (VLAN) *Framed (N*64Kbps) and unframed (2.048Mbps) optional *Ethernet port 10Mbps, Full/Half Duplex mode compatible *Frame mode support PCM30/PCM31 *Support CRC4 *Support internal clock, E1 recovery clock or V.35 line clock *Provide analog and digital loopback and remote digital loopback test *For E1 interface, 75ohm (unbalanced) and 120ohm (balanced) optional *For data interface, V.35 and V.24/RS232 optional *Comprehensive LED indicators on front panel, convenient for the diagnosis of equipment working state *Stand-Alone and Rack-Mount available *16-slots, elaborate cooling design and two redundant power supplies *Support management *-48V DC & 220V AC power supply optional Specifications: E1 & FE1 interface Comply with ITU G.703,G.704,G.706,G.823 Rate:2.048Mbps;N*64Kbps(N=1~31) Code type:HDB3 Impedance:75ohm unbalanced & 120ohm balanced optional Physical interface:BNC coaxical for unbalanced RJ45 twisted pair for balanced Ethernet interface Comply with IEEE 802.3/IEEE 802.3Q(VLAN) Rate:10Mbps,Half/Full auto-negotiation MDI/MDI-X optional Physical interface:10 Base-T(UTP);RJ45 V.35,V.24/RS232 interface Comply with V.35,V.24/RS232 standard Rate:2048Kbps;N*64Kbps(N=1~31) Transmission mode:Synchronization Data interface:V.35 or V.24/RS232 Physical interface:DB25 female jack,V.35 via external adapter Work mode:DCE Power supply AC power:220V¡¨¤10%,50Hz DC power:-48V(optional) Power:5W Environment Temperature:0¡«40¡æ Humidity:0¡«95% RH Carton.
Overview E3/t3-t is state of the art network termination units (ntu) connecting fast ethernet lans over e3 or t3 circuits. The devices enable service providers and isps to supply transparent. Ethernet services to remote locations over existing e3/t3 infrastructure. The devices can be used in a point-to-point application and widely used in lnteroffice or enterprise lan connection. E3/t3-t has one unframed e3 or one framed t3 port, and one 10/100basetx port. Packets are forwarded from the ethernet network to the e3 or t3 network at wire-speed, fully utilizing the expensive tdm circuit bandwidth. Features: * best price performance ethernet over e3 or t3 intelligent converter in the market * wire-speed forwarding fully utilizing the e3 or t3 circuit * vlan stacking and tagging enabling service providers to provide layer 2 transparent lan services while securing providers management * fault propagation of e3 or t3 error conditions to ethernet port * diagnostic collection on tdm and ethernet interfaces * comprehensive led indicators on front panel, convenient for the diagnosis of equipment working state * -48v dc & 220v ac power supply optional. Specifications E3 interface Comply with itu g.703 Rate: 34.368 mbps Code type: hdb3 Impedance: 75ohm unbalanced l Physical connector: bnc coaxial for unbalanced T3 interface Comply with gr-499-core, ansi t1.107, ansi t1.102 Rate: 44.736 mbps Code type: b3zs Impedance: 75ohm unbalanced l Physical connector: bnc coaxial for unbalanced Power supply Ac power: 220v+-10%, 50hz Dc power: - 48 v (optional) Power: 5w Environment Temperature: 0-40oc Humidity: 0-95% rh Carton.
Technical Specifications Operating standards: IEEE802.3z/AB, 10/100/1000Base-T and 1000Base-SX/LX/HX MAC address table: 4K Data Buffer: 256K Connector: UTP: RJ-45,10/100/1000Mbps; Fiber: LC,1000Mbps Cable : UTP cable: Cat 5e or Cat 6 (the max distance up to 100m) Fiber : multimode : 50/125, 62.5/125¦Ìm (the max distance up to 550/224m) singlemode : 8.3/125, 8.7/125, 9/125¦Ìm (the max distance up to 100km) Flow control Full Duplex: IEEE802.3x Half Duplex: back pressure. Power: AC 220V(170-260V) 50Hz; DC 5V£¬1A Ambient temperature: 0 ¡« +50 Storage temperature: -20 ¡« +70 Humidity: 5% ¡« 90% Dimensions: Internal Power: 40 (high) x 110 (width) x 140 (length) mm External Power: 26 (high) x 70 (width) x 93 (length) mm.
Operating standards: IEEE802.3u, 10/100Base-TX and 100Base-FX MAC addresses table: 1K Data buffer: Built-in 128Kbyte RAM . Connectors: UTP Connector: RJ-45, 10/100Mbps; Fiber Connector: ST/SC/FC, 100Mbps Cable: UTP: Cat. 5 (the max distance up to 100m) Fiber ( Multimode): 50/125, 62.5/125m, the max distance up to 2km or 5km Fiber ( Singlemode): 8.3/125, 8.7/125, 9/125, 10/125m, the max distance up to 20 -120km Flow Control Full Duplex: Supporting standard IEEE802.3x Half Duplex: back pressure LED: Power, FX SD, FX Link/Act, TX 100, TX FDX, TX Link/Act. Power Requirement: AC 170 ¡« 240V, DC 5V. Ambient Temperature: 0 ¡« 70 Humidity: 5 ¡« 90% Dimensions: Internal power: 30, 110, 140mm External power: 26, 70, 93mm.
1x Multimode Dual LC fiber Optical Port: 1.25Gbps, 850nm wavelength, support Gigabit Ethernet; 1x RJ45 Port: 10M/100M/1000M, supports Full/Half Duplex auto-negotiation and MDI/MDIX auto-crossover. Equiped with high-quality chip to ensure stability and Ultra-low time-delay data transmission. Complies with IEEE 802.3/802.3u/802.3z/802.3ab, 10/100/1000Base-TX/FX. Supports jumbo frame size 9K byte. Modulization configuration design, support hot-swappable, plug and play. And LED indicators for TX, FX LINK/ACT, POWER, FDX can dynamic feedback link connection state and fault detection to easily monitor network status. Only 93mm x 72mm x 27mm(3.7"x 2.8"x 1.1") in measurement. Its compact modular design facilitates deployment in a narrow desktop location to save space. Product List: 1x Gigabit Ethernet Media Converter, 1x 1000Base-SX SFP module, 1x DC Power Adapter, 1x Product Manual. 30-day Money-Back guarantee, lifetime tech support.
*** LNP-0602-M-T/ 6-Port Industrial PoE+ Unmanaged Ethernet Switch *** | Network broadcast storm protection | 4-Ports IEEE 802.3at compliant PoE+ Function with 30W/Port | 2-Ports 100Fx SC/ST type connector (Multi / Single mode) | Supports Auto MDI/MDI-X Function | Store-and-Forward Switching Architecture | 2K MAC Address Table | Surge Protection: 2,000 VDC support | ESD Protection: 6,000 VDC support | Redundant Power Input Design : 48~55VDC | Built-in 1 relay output for Port Break Alarm | IP30 Rugged Aluminum Case Design | DIN-Rail and Wall Mount support | Operating Temperature range- STD: -10° to 70° C, EOT: -40° to 75° C | 5-Year Warranty |
***LNP-0800-T/ 8-Port Industrial PoE+ Unmanaged Ethernet Switch, w/8*10/100Tx (30W/Port); EOT: -40~75C***| Network broadcast storm protection | 8-Port IEEE 802.3at compliant PoE+ Function with 30W/Port | Supports Auto MDI/MDI-X Function | Store-and-Forward Switching Architecture | 2K MAC Address Table | Surge Protection: 2,000 VDC support | ESD Protection: 6,000 VDC support | Redundant Power Input Design – 48~55VDC | Built-in 1 relay output for Port Break Alarm | IP30 Rugged Aluminum Case Design | DIN-Rail and Wall Mount support | Operating Temperature range - STD: -10° to 70° C, EOT: -40° to 75° C | 5-Year Warranty |
***5-Port 10/100TX Slim Industrial Ethernet Switch*** | Extended Operating Temperature -40° ~ 80° C (-40° ~ 176° F) | Store and Forward Switching Architecture | Flow Control on Full-Duplex | Back Pressure on Half-Duplex | Supports Auto MDI/MDI-X Function | Wide-Ranging Redundant Power Design | UL Class I, Division 2 Certified | DIN-Rail and Wall Mount Design | Slim IP-30 Case Design |
Support 10/100m remote manageable fx media converters, 10/100/1000m remote manageable fx media converters, 1 fx + 2 RJ45 ethernet media converter, 125m~4.25g oeo, and 10g oeo managed at the same time Cover all functions of common fiber media converters, what's more, it supports protocols like snmp, web, telnet and console They can realize the integrated management to all chassis. Media converter card supports protocols like q-in-q double tag vlan, ieee802.1q tag vlan and ieee802.3x flow control Interface for management: rs232 console port (RJ45) and 10/100mbps RJ-45 ethernet port. Supporting remote and local management. With centralized management and top tree, several chassis can be managed in the same interface at the same time; with grouping management any converter can be conveniently manipulated among many converters. Standard package
10/100 MBPS managed media converter Managed Media Converter is a 10/100Base-TX auto negotiation and auto MDI/MDIX cable selection Fast Ethernet Media Converter with intelligent network management that translates transmission signals from a twisted-pair 10Base-T or 100Base-TX cable to 100Base-FX fiber optic cable. It enables network managers and network operators quickly isolate problems without visiting multiple wiring closets, avoiding expensive downtime. With its SNMP manager, user can monitor and configure the Copper Port and Optical Port of center chassis and remote standalone easily. Besides, user can control the bandwidth rate limiting as N*32Kbps. Hardware Function Support 10Base-T, 100Base-TX, 100Base-FX Fully compatible with IEEE802.3, IEEE802.3u, IEEE802.3x standards Up to 5km distance on multi mode optical port and 120km distance on single mode optical port High-performance auto-negotiation chips make sure the data transfer with higher Security, stability and without block. Up to 1916 bytes package forwarded Support half/full duplex mode Auto-negotiate Low power consumption, low heat generation and excellent compatibility 10Watt professional communication power supply module inside the standalone. Chassis supports double redundant power supply modules and each power supply module Supports up to 100 Watt power output for the security and stability Support hot-swap for all the modules, but not including management module Single-strand/dual-strand optical module selectable, FC/SC/ST optical port slectable and standalone/16-slot chassis selectable. Device Size Standalone: 132mm (width)*36mm (depth)*122mm (height) 19-inch Chassis: 440mm (width)*125mm(depth)*250mm(height)
Created by Stephen Technologies Co.,LTD, The STE-228-X3X1 is a layer 2 fiber switch that offers along with multiple layer 3 features. The STE-228-X3X1 fiber optic switch is especially designed for telecom grade applications. It offers 24 10/100mbps fiber(SM or MM fiber), together with 4 gigabit combo ports. The combo ports of STE-228-X3X1 can be either 4 port gigabit copper, or 4 port gigabit sfp/gbic modules. It can also be configured as 2 10/100/1000Base-Tx ports, plus 2 gigabit SFP module ports. 1pc/box