MOTOR manufacturing specification [FPCB MULTY] 1. Layer : FPCB 4 layer 2. Application : motor 3. Thickness : FPCB 0.1T / MULTY 0.3T 4. L/S : 50 micrometer/50 micrometer 5. Drill : LASER DRILL 0.08 mm 6. ANNULAR RING : 42.5 micrometer 7. SPECIAL item for controlling : Outer layer [14 layers ANNULAR RING ]
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
Steel frame screens are mostly applied to the shale shakers with wedge fastening equipment. The screen frames adopt that high-strength square steel tube welded to multi-ribbed construction. They are sturdy and reliable. These screens are constructed with two or three stainless steel layers bonded to a steel support plank. Accessary rubber plugs may be used to repair rips or tears. By doing this, we can cut down time and reduce the production costs. We can supply steel frame screens with mesh sizes ranging from 20 to 250. Steel frame screen is in common used presently, that are constructed mostly withe two or three stainless steel layers bonded tightly to the steel frame.The frame is made up of the high-strength square steel tube or flat steel welded to multi- ribbed construction.These layers are coupled with the frame through metal backing plate or bonded straightly as well.We possess the strong experience and the ripe technology,and will provide various specifications of steel frame screens to serve the clients' demands. Features of Steel frame screen 1. Different layers with different density. To arrange these layers reasonably and exactly, the screening effect will become more and better. 2.High strength frame, multi-ribs and the mesh cloth with moderate tension , from one reliable combination , which can increase screen�??s acceptable flow , the intensity and the lifetime 3.The wedge-shaped fastening device, can make the erection of screens more handily and quickly 4.The mesh divided into many independent small units by grids of the backing plate ,can prevent rips or tears from spreading overmuch. Accessory prepared rubber stoppers can be used to repair damage. By doing so, the operator can cut down the stop time and reduce the cost.
Hot eye Onion Peeling Machine Automaitc onion peeling machine with onion root cutting in-one-machine 1 The whole process of onion from feeding, peeling, peeling, root cutting, output and other processes is automated and unmanned, which can save a lot of labor costs. 2 Peel by layers, either more or less. The equipment is designed with a cortex controller, which can be peeled as required. Only one layer of skin can be peeled, or two or three layers of skin can be removed. 3 The peeling is clean and effective. The peeled scallions are clean and good in appearance. 4 The root cutting part is equipped with an onion size recognition mechanism, and the size of the cutting amount can be adjusted randomly to avoid the disadvantage of cutting large onions into small ones and small ones into large ones. 5 Small size, high yield. The equipment design strives to reduce the volume on the premise of increasing the output, so as to apply to various application scenarios such as large, medium and small enterprises and small family workshops.
Factory Automatic Hot Eye Onion peeling process machine,from small capacity to big capacity Onion peeling process: the onion is manually fed into the hopper --- the conveyor belt automatically feeds the onion into the peeling box for peeling --- after peeling, the onion goes into the peeling roller. Under the action of high-pressure air at the side, the first and second layers of the onion are peeled off and sent out to complete the whole processing process. Features: 1. Advanced technology, reasonable mechanism, beautiful appearance, safe and reliable use, all stainless steel. 2. Automatic peeling without damage. 3. The depth of peeling is even. 4. The feeding belt is used for automatic feeding, which is simple in design and convenient in use. 5. Less peeling, high recovery rate of finished products, and over 98% of finished products. 6. Mechanical processing eliminates the hidden danger of manual processing of infectious diseases and unsanitary products. Parameters 1.process arrange diameter of round shape onion 30-150mm. 2.capacity 1000-1500kg/h 3.Power 3kw 4.Voltage 380V 5.Air Compressor :flow 1.5m2/min, pressure 0.7MPa ,power 11kw 6.Machine size 1.5*1.3*1.4m 7.Weight 420kg Start working flowing: 1.Fill onion in the loading box 2.Start the pneumatic valve switch 3.Start the power-supply switch 4.According to onion drying or fresh to adjust loading speed button/air pressure ,in order to ensure the clean degree of removing onion skin 5.When finished adjusting ,The equipment operates normally and automatically.
Belt press juicing machine for fruit vegetable Use for : 01.fruit juice 02.vegetable dehydration or juce 03.enzyme juice 04.Extraction of medicinal juice 1. High lift and large flow, strong pumping force, not easy to block, precision casting pump body, lasting work, high efficiency and energy saving, after-sales guarantee 2. Long service life. The product is equipped with a new automatic deviation correction and tension system, automatic operation, uniform distribution of materials, extended filter bag life, and long bearing service life 3. Rust-proof and corrosion-resistant, tough shell, stable operation, unique oblique lengthened wedge design, more stable operation and low noise 4. The treatment effect is good. Two sets of independent backwashing systems are adopted. The multi-roll diameter decreasing backlogs are compact in layout and the filter cake has high solid content. 5. Efficient, convenient and ultra-long gravity dewatering area, with large bearing capacity, strong processing capacity, low power consumption and low operating cost 6. Juice yield 85% Small capacity 500-3000kg/h,filter belt width 500-2000mm,power 1.5-3kw, filter belt speed 1.5-3.5m Big capacity 3-20T/hour,power 14.7-41kw ,machine size length 3100-5420mm Width 1475-3430mm high 1820-2420mm
4-Layer, Immersion Gold-PCB 4 Layer PCB Board, Immersion Gold PCB, Customized PCB, High Frequency Board, HDI PCB Supplier Layer: 4L Board thickness: 0.8mm Suface Finish: Immersion Gold Trace/Space: 5/6mil Smallest Hole Diameter: 0.25MM PCBMAIN can OEM PCB including single-side PCB, double-side PCB, immersion gold PCB, high frequency board, HDI PCB, high density multilayer PCB, multilayer PCB including 2 layer flexible PCB, 4, 6, 8, 10, 12 layer PCB board.
4-layer printed circuit board with selective hard gold coating 50 micro inch (1.25 micrometers) Pcb p / n: 842378 1. Number of layers: 4 layers 2. Material: fr4 Thickness 3.Board: 1.6mm 4. Copper thickness: 1/1/1/1 ounce of copper 5. The minimum drill size: 0.2 mm 6. Minimum track and clearance: 0.125 mm 7. Surface: submerged gold + selective solid gold 8.Green soldering mask 9.Special technology: selective solid gold coating up to 50u "(1.25um) 10.Applications: consumer electronic products 11.One stopping the turnkey service of ems, including the purchase of materials, smt and through assembly, assembly of prefabricated boxes 12.Ul is recognized and complies with rohs requirements.
We at GREENLAND FRESCO procure Peanuts in the most professional way and always ensure that fresh and healthy products are delivered to our clients. We keep pace with the latest technology and market requirements to ensure stability & sustainability towards fulfilling the clients demand. We have built a cost-effective and reliable supply chain to deliver Java & Bold varieties of Peanuts in one click. We maintain aflatoxin level & moisture content at minimal level. Peanuts are processed at processing plants to obtain the required specifications specified by our clients. Specifications of Bold / Java / Blanched Bold / Blanched Java Peanut kernels : - Type - Peanut kernels Peanuts counts per Ounce - 38/42, 40/50, 50/60, 60/70, 70/80 Origin - India Admixture - 1% max Oil content - 42% - 48% max Foreign Material - 0.50% max OR 1% max Moisture - 7% max OR 8% max Aflatoxin - Aflatoxin negative 5/10 PPB Gross Wt. per Bag - 10/15/25/50 Kgs Packaging Material - New Jute Bags Load Ability : One 20" FCL can load 19 MTS or 380 Bags of 50 Kgs New Jute Bags One 20" FCL can load 19 MTS or 760 Bags of 25 Kgs Vacuum Bags New vacuum pack inside and outer layer with PP woven bags 25 Kgs Gross Specifications of Peanuts in Shell Bold / Java : - Type - Peanuts in shell Bold : HPS- Ground nuts Peanuts bold shell - 18/22, 20/24, 22/26 Counts/Ounce Origin - India Moisture - 6-8% Max Admixture - 1% Max Imperfect - 5% Max Aflatoxin(B1+B2+G1+G2) - 5-10 ppb (as per clients specifications) Packing - In Strong Jute Bags of 30 Kgs Net/Gross Each One 20" FCL can load 12-14 MTS One 40" FCL can load 19-20 MTS Health Benefits 1. Peanuts have a strong nutritional Profile 2. Peanuts can reduce the risk of Heart disease 3. Peanuts are excellent source of plant based protein, fiber and many key vitamins and minerals. 4. Peanut consumption reduces the risk of weight loss and obesity 5. Peanut consumption reduces the risk of colorectal cancer
Description 1. High purity (Sn99.99 Sn99.95 Sn99.90), excellent weldability, good infiltration. 2. Clean, beautiful. After welding, insulation, high resistance, low ionic contamination, PCB board welding residual minimal. 3. Good oxidation resistance, low tin slag and cost savings. 4. Solder joint is bright, full and uniform. 5. Economical and can produce the lowest consumption of the solid solder joints. Application Tin ingot is widely used as a coating material in High precision electronic Products, and other requirments of precision welding products, general electronics, food industry packaging, automotive and electrical industry, and hightemperature resistant products.
Fr4 /aluminum /cem1 material; Min. Hole size 0.2mm; Min.Line space and width 4/4mil; Hole cooper wall 25um; Vacuum, cartoon 27*30*24
.Lasting Beautiful Color. Color stable. 2.Good Sound Insulation. Roof tile composite co- extrusion core layer shielding structure can greatly reduce sound transmission. 3.Heat Preservation And Heat Insulation. 4.Excellent Anti-corrosive And Excellent Weather Resistance. PVC roof tile can long resist acid, alkali, salt and other corrosive chemicals. It suitable for using in corrosive workshop, acid rain-prone area and coastal area. 5.Good Fire Resistance With Excellent Insulation And Excellent Waterproof Performance. Belonging flame retardant material, with fire resistance tested by national authoritative departments. The roofing sheet selects highly weather-resistant resin, which is dense and absorbing no water, with no pore penetration problem.
The material and functions: 1. Hydrophilic non-woven: soft, make baby more comfortable. 2. Super Absorbent Polymer: Absorb the liquid effectively and instantly, keep surface dry all day to avoid wet back. 3. Blue Acquisition Distribution Layer: Make the liquid infiltrate quickly, prevent rewet and keep Baby's skin dry and clean. 4. Lamination film: breathable, prevent leakage and keep fresh. 5. PP tapes: go well with frontal tape, they can be used as many times as need. 6. Magic tapes/BIG ELASTIC EARS: can be used for many times, and big elastic ears are much more convenient for a better fit. 7. 3D rounder: avoid any side leakage. 8. Elastic waistband: Provide baby with a snug, comfortable circumstance. Pampers Diapers Huggies Diapers Earth's Best Diapers Pampers Newborn Pampers Maxi Pack Mini Pampers Maxi Pack Midi Pampers Maxi Pack Maxi Pampers Maxi Pack Maxi plus Pampers Giant pack Maxi Pampers Giant pack Maxi Pampers Giant pack Maxi plus
The material and functions: 1. Hydrophilic non-woven: soft, make baby more comfortable. 2. Super Absorbent Polymer: Absorb the liquid effectively and instantly, keep surface dry all day to avoid wet back. 3. Blue Acquisition Distribution Layer: Make the liquid infiltrate quickly, prevent rewet and keep Baby's skin dry and clean. 4. Lamination film: breathable, prevent leakage and keep fresh. 5. PP tapes: go well with frontal tape, they can be used as many times as need. 6. Magic tapes/BIG ELASTIC EARS: can be used for many times, and big elastic ears are much more convenient for a better fit. 7. 3D rounder: avoid any side leakage. 8. Elastic waistband: Provide baby with a snug, comfortable circumstance. Pampers Diapers Huggies Diapers Earth's Best Diapers Pampers Newborn Pampers Maxi Pack Mini Pampers Maxi Pack Midi Pampers Maxi Pack Maxi Pampers Maxi Pack Maxi plus Pampers Giant pack Maxi Pampers Giant pack Maxi Pampers Giant pack Maxi plus
Code 93200: Suitable for the removal of bad odor, organic vapours from polluted environment, and for riding bike and motorcycle. Features Suitable for the removal of bad odor, organic vapors from polluted environment, and for riding bike and motorcycle. 1. Type: Flat shape, 4-ply, non-sterile 2. Size: For adults 3. Color: White 4. Outer Layer: Water-repellent non-woven Middle 1 Layer: Activated carbon with PE+ polyester Middle 2 Layer: High level static filtration non-woven Inner Layer: Microfilter thermal-bond non-woven 5. Nose band: PE iron wire
Features: Suitable for OR, ER, patient care area, oral, dental procedure, clinics, isolation, IC practices, patients and other applications. 1. Type: Flat shape, 3-ply, non-sterile 2. Size: For adults 3. Outer Layer: Water-repellent non-woven 4. Middle Layer: High level static filtration non-woven 5. Inner Layer: Microfilter Thermal-bond non-woven 6. Nose band: PE iron wire
Wearing a mask is a fashion unique, inspires imagination, cultivates the creative spirit, improves school or company image, and dresses stylishly and effectively to prevent covid-19. 1. Type: Diamond shape, 3-ply, non-sterile 2. Size: M, L 3. Color: as photo 4. Outer Layer: Water-repellent non-woven 5. Middle Layer: High level static filtration non-woven 6. Inner Layer: Microfilter Thermal-bond non-woven 7. Nose band: PE iron wire
Code 91100: 4-ties Features Suitable for OR, ER, patient care area, oral, dental procedure, clinics, isolation, IC practices, patients and other applications. 3-ply, non-woven material, 99% BFE at 3 micron. 1. Type: Flat shape, 3-ply, non-sterile 2. Size: L 3. Color: Green, blue, pink, white 4. Outer Layer: Water-repellent non-woven 5. Middle Layer: High level static filtration non-woven 6. Inner Layer: Microfilter Thermal-bond non-woven 7. Nose band: PE iron wire