We are a leading supplier of electroplating chemicals, industrial polishing and welding consumables, water treatment, powder coating, fertilizers. We stock and carry an extensive range of ready to use chemicals. We deal with so many different chemicals and we would like you to contact us for more information about our different chemicals and products.
Footwear, shoes, slippers ,sandals.
Fertilizers, chemicals, petrochemicals, minerals, woods & polymers.
Polymer resins off grade, cotton waste & plastic scrap, plastic products.
FH SERIES OF PRODUCTS: FH products are Pure nonionic derived the endosperm of guar polysaccharide (Cyamopsos tetragonolobus). The products are unique with ultra-high viscosity with fastest hydration characteristics as shown in Figure 1 below. Also, when added with other drilling components, to seawater, a KCl solution or other aqueous system, the product suspension disperses readily without lumping, even under low-shear conditions generating most of its full viscosity within just a few minutes. PRODUCT COMPATIBILITY: FH series of products are compatible with most of the chemicals and auxiliaries used in drilling operations. However, the products are not compatible with Arabic and Crystal gums. Also, in presence of borates they form elastic gel. PRODUCT APPLICATIONS: FH series of products are natural, high viscosity, fast hydrating non-Newtonian hydrocolloids with suitable cross linking components in diesel slurries and are versatile for continuous mix applications, where extremely fast hydration and subsequent viscosity development is required. They are excellent viscosifiers, stabilizers, thickeners and suspending agent for use in oil-drilling, workover fluids and several other oilfield applications like hydraulic fracturing, oil well stimulation, mud drilling, oil well capping, flocculent and liquid shoring etc. The product is used as a surfactant; synthetic polymer and deformer ideally suited for all rheological requirements of water based and brine based drilling fluids. Specifications:- PRODUCT : FH-35 FH-38 FH-42 CAS No. : 9000-30-0 9000-30-0 9000-30-0 Granulation : FINE FINE FINE APPEARANCE : OFF WHITE POWDER MOISTURE : 8% Max. 8% Max. 8% Max. PROTEIN (N X 6.25) : 5.0% Max 5.0% Max 5.0% Max ASH : 1.5% Max. 1.5% Max. 1.5% Max. ACID INSOLUBLE RESIDUE (A.I.R.) : 3% Max. 3% Max. 3% Max. CARBOHYDRATE (incl gum by difference) : 82% Min 82% Min 82% Min pH (1% Solution) : 5.5 ? 6.5 5.5 ? 6.5 5.5 ? 6.5 VISCOSITY : (0.48% Product in 2% KCL Sol. 2.5 mins mix @1500 RPM in waring blender) Fann 35sa Viscometer at 300 RPM, 25�C 3 Mins : 35 3 Min:38 3 Mins : 42 5 Mins : 37 5 Mins : 39 5 Mins : 43 30 Mins : 39 30 Mins : 42 30 Mins : 45 60 Mins : 40 60 Mins : 43 60 Mins : 47
Fresh fish, fresh fruits, dried fruits, canned products, nuts, and locally made products. petrochemical. e.g. bitumen, petroleum items, diesel, polymers. methanol, car engine oil, shipping services, sts..
Organic and inorganic chemicals, calcium carbonate all kinds of salts such as rock, himalayan, bathing, table, black, kosher, flake, red hawaiian and pickling salt etc. petrochemicals (polyethylene, polypropylene and polymers etc.), agrochemicals ( fertilizers such as dap, urea 46 etc.), pesticides and herbicides etc.), agricultural foods & commodities such as wheat flour, millets, other flours, onion , potato, tomato and apples, banana, guava, mango, rice bran, rice husk, lentils and pulses, non basmati & basmati rice items such as carpets and rugs used in home and offices, handicraft items and paper cups and corrugated boxes..
In Industrial Applications guar gum powder is a very versatile product and finds its different applications, as thickening, sizing agent, wet-end strength additive, gelling agent and water barrier, flocculation aid, for waste water treatment, as emulsifier, binder. Also used for mud formulations, enhanced oil recovery, polymer flooding, well treatment, lost circulation plugging etc. Mining grade guar gum is used in mining industry as a floatation agent flocculating or setting better quality agent. Fast hydration guar gum powder for oil drilling applications is an important advantage of guar gum. Altrafine Gums in India supply oil drilling grade guar gum, guar gum for paper industry, guar gum as an emulsifying, guaran and sickle pod.
During last decade Guar has immerged as an important industrial raw material and Produced by man for thousands of years. India has been the single largest producer and exporter of Guar gum accounting for more than 80 percent of the global output and trade. Guar has now assumed a larger role among the domesticated plants due to its unique functional properties. India Ranks First in the production of guar which is grown in the North Western part of the Country which mainly includes the states of Rajasthan, Gujarat, Haryana and Punjab. Other main countries are Pakistan, U.S.A and Brazil The by-product of Guar Gum industry consisting of the outer seed coat and germ material is called guar meal. The Guar meal after gum Extraction is a potential source of protein and contains about 42% crude protein which is one and a half times more than the level of protein in guar seed. The protein content in guar meal is well comparable with that of oil cakes. It is used as a feed for livestock including poultry. Guar meal contains two deleterious factors i.e. residual guar gum and trypsin inhibitor, Toasting of Guar Gum improves its nutritive value in chicks. Toasted guar Meal can be used in limited quantity i.e. Up to 10% in Poultry diet. However it can replace groundnut cake by almost 100% in animal feeds. Guar Gum (Galactomanan) is a high molecular weight carbohydrate polymer made up of a large number of mannose and galactose unit linked together. The crude Guar Gum is a greyish white powder 90% of which dissolves in water. It is non ionic polysaccharide based on the milled endosperm of the guar bean whose average. Composition is: Hydrocolloid: 23% Fats: 40% Proteins: 34% The most important property of the Guar is its ability to hydrate rapidly in cold water to attain a very high viscosity at relatively low concentrations. Its specific colloidal nature gives the solution an excellent thickening power which is 6 to10 times thicker than that obtained from starch. It is stable over a wide range of PH and it also improves the flow ability and pump ability of the fluid. It is a superior friction loss reducing agent.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
EcoTexTM-SL20 - PVA FREE ONE-SHOT PRODUCT DESCRIPTION New generation eco-friendly one-shot product for a high-speed shuttleless loom. It is mainly used for 6 to 203 cotton yarns sizing. This product is entirely biodegradable and ecological. Products are made from grafted starch, anionic polymers, and synthetic fatty matters. It contains a maximum of 13% moisture and an optimized viscosity level. Easily disperse in cold water with little swelling property due to high binding property. Having high penetration power and plasticizing power for heavy construction fabrics weaving. SPECIFICATIONS 1.Appearance - Off white powder 2.pH value of 5% solution - 6 to 8 3.Solubility - Partially soluble in cold water 4.Viscosity of size mix - 5 to 6 sec (SITRA -6mm cup) 5.Total Moisture - Max 13% 6.Bulk density - 0.5 to 0.6 g/ml 7.Total ash - Max4% COOKING METHOD 1. Fill the required quantity of water in the cooker. 2. Gradually add EcoTexTM-SL20 and mix for 2 min. 3. Add other ingredients and mix for 2 min. 4. Close the pressure cooker lid. 5. Open the steam value and cook to @ 120�? �ºC or 35psi. 6. Retain in the cooker for 15 to 20 minutes. 7. Then transfer the size mix to storage. PROPERTIES 1. Moisture regain: The formation of thin flexible film absorbs water molecules from atmospheric air that maintains the required moisture content of the sized yarn. This property improves the weaving efficiency by reducing the warp stops. 2. Film property: The very thin strong film gives the inter fibre penetration that improves yarn tensile strength. Optimum elongation and flexible property significantly reduce warp break by overcoming the applied tension during weaving. 3. Abrasion resistance: A strong film withstands the mechanical friction between yarn to yarn and yarn to machine parts like reed, dropper pin, heald wire, and weft picking element. DE-SIZING Easily de-sizable product with hot alkali treatment. STORAGE Keep away from direct sunlight and store in a cool, dry, and well-ventilated place. STABILITY Stable for one year from the date of manufacture. PACKING Available in 50Kg net weight PP bags with moisture-proof liner inside.
TECHNICAL DATASHEET EcoTexTM -SL55 - PVA FREE ONE-SHOT PRODUCT DESCRIPTION Powder types unique one-shot product which needs no extra native starch, modified starch, binder, softener, lubricant to be added further. It is mainly used for Shuttle-less loom woven warp yarns counting above the 40s to 60�¢??s Cotton. Products are made from grafted starch, anionic polymers, and synthetic fatty matters. It contains a maximum of 13% moisture and an optimized viscosity level. Easily disperse in cold water with little swelling property due to high binding property. SPECIFICATIONS 1.Appearance - Off white powder 2.pH value of 7% solution - 5 to 7 3.Solubility - Partially soluble in cold water 4.Viscosity of size mix - 4 to 5 sec (SITRA -6mm cup) 5.Total Moisture - Max 13% 6.Bulk density - 0.5 to 0.6 g/ml 7.Total ash - Max4% COOKING METHOD 1. Fill the required quantity of water in a cooker 2. Gradually add EcoTexTM-SL55 and min for 2 min. 3. Close the pressure cooker lid. 4. Open the steam value and cook to @ 120�? �ºC or 35psi. 5. Retain in the cooker for 15 to 20 minutes. 6. Then transfer the size mix to storage. PROPERTIES 1. Moisture regain: The formation of thin flexible film absorbs water molecules from atmospheric air that maintains the required moisture content of the sized yarn. This property improves the weaving efficiency by reducing the warp stops. 2. Film property: The very thin strong film gives the inter fiber penetration that improves yarn tensile strength. Optimum elongation and flexible property significantly reduce warp break by overcoming the applied tension during weaving. 3. Abrasion resistance: The strong film withstands the mechanical friction between yarn to yarn and yarn to machine parts like reed, dropper pin, heald wire, weft picking element. DE-SIZING Easily de-sizable product with hot alkali treatment. STORAGE Keep away from direct sunlight and store in a cool, dry, and well-ventilated place. STABILITY Stable for one year from the date of manufacture. PACKING Available in 25Kg net weight PP bags with moisture-proof liner inside
Industrial chemicals likes tetra sulpho optical brightener and di sulpho optical brighteners for pulp and paper, caustic soda flakes / sodium hydroxide, caustic soda lye, asa sizing agent, akd sizing agent, wet strength resin agent / dry strength resin (polyamido polyamine epichlorohydrin resin with a high% of solids 25 35%), sae anionic for sizing agent (butyl acrylate styrene polymer 24 26%), sae cationic for sizing agent (copolymer n [3 (dimethylamino) propyl] methacrylamide / styrene ]]) for paper industry, fluorescent brightening agents, optical brighteners for paper, fluorescent whitening agents, optical brightener, carbomer, carbopol, polyaluminium chloride, carbon brushes and brush holders, pp granules, plastic granules, eps granules and many more..
PET clear tray bale No label, no other polymer 16 tons 1 load Origin in USA
Petrochemicals, hdpe, pe, pp, pvc , plastics, polymers.
Lians is a reliable supplier in plastic watse recycling business. We can supply HDPE product as below: HDPE Blue Crate Regrind For Recycling MATERIAL: HDPE Blue Crate Regrind CATEGORY: HDPE TYPE: Regrind GRADE: Injection SPECIFICATION: *Speciment conditioning: None *Test Temperature: 190�?�°C *Test Mass (Km): 2.16 *Nature (form) of Charged Material: Polymer pieces *Smooth Surface *Melt flow rate (gram/10minutes): 4.47 Origin: Aus LOADING WEIGHT: 22 Tons FOB (USD/Ton): 650-700
POM regrind black color full container available POM plastic possesses the same priority features as other plastic polymers, some of the highlights of the special resin: High hardness Bearing good Low friction number High resistance to abrasion High temperature resistant Less water intake Has anti-static ability Dimensional stability, little change Less smoke burns when burning High glossy surface High crystallization In addition to the priority points, POM plastic also has some limited formats such as: Quality acid resistance and alkali High hatch rate when changing secretions Operation mode Heat range MATERIAL: POM regrind black color full container available CATEGORY: POM TYPE: Regrind GRADE: Black color SPECIFICATION: 1 full container available Origin: Tunisia LOADING WEIGHT: 23 Ton FOB (USD/Ton): 650$ - 850$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
We are a leading supplier of electroplating chemicals, industrial polishing and welding consumables, water treatment, powder coating, fertilizers. We stock and carry an extensive range of ready to use chemicals. We deal with so many different chemicals and we would like you to contact us for more information about our different chemicals and products.
POM Regrind from zipper Teeth, industry lump, industry runner Definition of POM resin (polyformaldehyde resin): polyformaldehyde is a linear polymer without side chain, high density and high crystalline properties. According to different chemical structures in the molecular chain, there are two types of homoformaldehyde and copolymers. of both types of polyformaldehyde density, high crystallinity, melting point, but thermal stability, the treatment temperature range is narrow (about 10oC), slightly lower in acid and alkali stability; The density of formaldehyde, melting point, strength and copolymer is lower, but good thermal stability, not easy to decompose, wide range of treatment temperature (about 50oC), acid and alkali stability are good . Plastic has excellent all-round performance. Good physical, mechanical and chemical properties, especially with excellent friction resistance. It is commonly referred to as steel or strip, which is the general engineering plastic third. Suitable for reducing wear on parts, transmitters, chemicals, tools and other parts. One of the synthetic resins, also known as polyformaldehyde resin, POM resin and steel, etc. This is a kind of white or black plastic resin with high hardness, high steel and high wear resistance. Used for gears, bearings, auto parts, machine tools, tools, etc. MATERIAL: POM Regrind from zipper Teeth , industry lump, industry runner CATEGORY: POM TYPE: Regrind SPECIFICATION: from zipper Teeth , industry lump, industry runner,Qty per month 52 mt Origin: Bangladesh LOADING WEIGHT: 24 Ton FOB (USD/Ton): 650$ - 850$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
