Jj 5 Cement Mortar Mixer Suppliers and Manufacturers

Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor

PRODUCT DATA SHEET ACID RESISTANT BRICK Material : RED SHALE Type Acid Resistant Brick Size (mm) 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions Heavy thermal shock Typical Physical Properties of GANESHAS Acid and Chemical Resistant Brick Characteristic RED SHALE ACID RESISTANT BRICK Test Standard Bulk Density, gm/cc - 2.3 to 2.35 ASTM C-20 -Water Absorption, % - 0.1 to 1.5 IS 4860-1968 Apparent Porosity, % -0.5 to 1.75 S 4860 Acid Solubility (H2SO4), Loss in Mass,% -0.1 to 1.8 ASTM C-279 Modulus of Rupture, PSI -2133 to 3555 ASTM C-67 Compressive Strength, Kg/cm2 - 700-900 IS 4860-1968 Abrasion Resistant , Volume in mm3 -69 to 85 EN 102 Surface Hardness, MOHS Scale - 7

PRODUCT DATA SHEET ACID RESISTANT BRICK Material : FIRECLAY Type Acid Resistant Brick Size (mm) : 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : * We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: * Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions - Heavy thermal shock Characteristic Fireclay Type Acid Resistant Brick - Test Standard Bulk Density, lbs/ft3 - 2.25 to 2.30 ASTM C-20 Water Absorption, % - 0.1 to 1.8 ASTM C-20 Apparent Porosity, % - 4.05 to 4.14 ASTM C-20 Acid Solubility (H2SO4), Loss in Mass,% - 6.1 to 6.8 ASTM C-279 Modulus of Rupture, Mpa - 14.6 ASTM C-67 Compressive Strength, PSI - 15500 to 17250 ASTM C-67 Abrasion Resistant , Volume in mm3 - 71 to 96 EN 102 Surface Hardness, MOHS Scale - 7 Thermal Conductivity, BTU-in/hr-ft-F - 6.94 to 7.12 ASTM C-236 Thermal Expansion Coefficient,in/in/Fx10-6 - 2.6 to 2.8 EN 103

Acid / Alkali Resistant Tiles/Bricks * Our Acid proof tiles, Acid alkali resistant tiles, Chemical resistant tiles are fully vitrified tiles which are manufactured using special non ferrous clay, processed at extremely high temperatures this process causes the raw materials to fuse and form a compact mass with an extremely low water absorption of less than 0.5% resulting in the formation of a very strong body with a flexural strength of 38 N/mm2, solid through color fade proof with a very hard surface Mohs hardness of 7. * The acid resistant tiles come in a range of sizes and thicknesses from ranging from 8-25mm. Our acid proof tiles meet stringent specification norms of IS 4457:2007 and relevant ASTM/DIN standards which ensure excellent performance in Acid/Alkali/Chemical (expect Hydrofluoric acid and its derivatives). Corrosion Protection Applications * Factory Floors subject to corrosion from Chemicals, Acids, Oil & Solvents * Pickling tank and surrounding areas * Food & Beverage Industry flooring * Battery rooms and Control rooms * Demineralization plants * Walls of washing and Paint shop areas * Acid Resistant Tiles Manufacturers India * Our acid proof tiles provide excellent abrasion resistance, anti-skid properties for worker safety and high aesthetic appeal. We also provide specialized corner tiles for reducing chances for acid attack through construction joints. Our standard sizes are 200x100, 200x200 & 300x300 millimeters.

The Ground Granulated Blast Furnace Slag (GGBS/GGBFS) is a type of eco-friendly green building material and high quality secondary cementitious material for concrete and cement. It is recognized as one of the best secondary cementations material for building high durable concrete stricture in the world today! GGBS has taken over a top place of high-performance cement and concrete mineral additives with its unique characteristics of hydration, low-price raw material. GGBS is obtained by quenching molten iron blast furnace slag (a by-product of iron and steel making) in water or steam. It is then further grounded into the desired fineness in terms of the required particle size distribution. The main components of blast furnace slag are CaO (30-50%), SiO2 (28-38%), Al2O3 (8-24%), and MgO (1-18%). The other important aspect of GGBS is its superiority in concrete durability which extends the lifespan of buildings from fifty years to a hundred years. APPLICATIONS Soil stabilization Mortar Used in combination with Portland cement Pre-cast concrete Ready mix concrete Specialist projects

2Lians can supply Plastic scrap product as below: PP Big Bag B Grade Plastic Scrap MATERIAL: PP big bag B grade CATEGORY: PP TYPE: Big bag GRADE: B grade SPECIFICATION: PP big bag B grade from Spain,5 loads available. Used for Agriculture products,no smell ,no cement,no fertilizer. ORIGIN: Spain LOADING WEIGHT: 18 Tons FAS (USD/Ton): 350-500

Rice Husk 1. Its high silica content makes it useful for strengthening building materials 2. It resists fungal decomposition 3. It resists moisture penetration 4. It decomposes slowly 5. It insulates well 6. Itâ??s renewable It has been used as building material, fertilizer, insulation material, or fuel. Combustion of rice hulls produces rice husk ash (RHA) which is a potential source of amorphous reactive silica. Most of the ash is used in the production of Portland cement.

Since 36 Years, we JAY KHODIYAR INDUSTRIES are recognized as a trustworthy manufacturer, Exporter and supplier of Food machinery. In order to manufacture high-quality food machinery our professionals employ advanced machines and utilize quality tested material procured from the authentic vendors. In addition, our clients can avail these food machinery from us at a reasonable price.

it is mainly used for color cement, color cement floor tiles, color cement tiles, imitation glazed tiles, concrete floor tiles, color mortar, color asphalt, terrazzo, mosaic tiles, artificial marble and wall painting. 2. It can be used for colouring and protecting substances of various coatings, including water-borne interior and exterior wall coatings, powder coatings, etc. It can also be used for various primers and topcoats such as epoxy, alkyd, amino, etc. in oily paints, as well as for toy paints, decorative paints, furniture paints, electrophoretic paints and enamels. Iron red primer has anti-rust function, can replace high-priced red red paint, save non-ferrous metals. The manufacturer supplies iron oxide red, iron oxide green, iron oxide blue, iron oxide yellow, iron oxide violet, iron oxide brown, iron oxide black and so on. The color is complete, the quantity is large and the discount is favorable. Support mixed batches. Welcome to call for consultation.

1. Basalt short fiber - a new material to replace steel fiber. Basalt short fiber is an inorganic mineral fiber with a length of less than 50mm, which can be evenly dispersed in cement concrete. 2. Characteristics of basalt short fiber (1) the specific gravity of steel fiber is 7.8 and that of cement concrete is 2.5. After mixing, the specific gravity of steel fiber is higher than that of cement, and the cement will sink and have poor dispersion. The specific gravity of basalt short fiber is 2.6, which is basically equivalent to that of cement concrete. After mixing, it does not sink, has good dispersion, is degradable, and is green. The road surface will not be as hard as steel fiber, resulting in car driving noise.. (2) Basalt staple fiber is a real "multifunctional" fiber. Acid and alkali resistance (especially alkali resistance, fully applicable to cement concrete), low and high temperature resistance, insulation and sound insulation. The tensile strength is three times that of steel fiber. The corrosion resistance of basalt fiber is better than that of steel fiber. The compressive strength is 20% higher than that of steel fiber, which is suitable for harsh environment. It has excellent comprehensive performance. (3) Low cost. The price of basalt fiber used in cement concrete is significantly lower than that of 50% steel fiber. (4) Natural compatibility. Basalt fiber is a typical silicate fiber, which is easy to disperse when mixed with cement concrete and mortar. Fresh basalt fiber concrete has stable volume, good workability and durability, and has excellent high temperature resistance, impermeability, crack resistance and impact resistance.

Produced by Chongqing Hesheng Longgang Technology Co., Ltd. (manufacturer) Basalt fiber reinforcement (new material to replace reinforcement) Product Description: basalt fiber reinforced bar (BFRP) is a new composite material formed by pultrusion process. It is made of basalt fiber as reinforcement, resin, filler and curing agent. Now it has been widely used in construction, highway and bridge constructionã?? Basalt fiber reinforcement can completely replace ordinary steel reinforcement and deformed steel; Compared with ordinary reinforcement, it has strong advantages: (see Annex for technical parameters) 1. The cost is the same as that of ordinary reinforcement; 2. The strength is 200% of the ordinary reinforcement with the same specification and diameter; The tensile strength reaches 1100mpap; The reinforcement is only 450MPa, 3. Basalt fiber reinforcement, especially with high acid, alkali and corrosion resistance, is a kind of electrical insulator that will never rust. 4. Basalt fiber reinforced bar, which is non-magnetic. It has high tolerance to the moisture concentration in cement mortar and the penetration and diffusion of carbon dioxide, and can prevent the corrosion of concrete structure in harsh environment, so as to improve the durability of buildings and bridges. 5. The specific gravity of basalt fiber reinforcement is 2.1g/cm3; The specific gravity of steel and reinforcement is 7.85/cm3; The diameter weight of the same specification is 370% lighter than that of steel reinforcement, and the strength is 200% of that of steel reinforcement. 6. The physical properties of basalt fiber reinforcement are higher than that of steel reinforcement, and the cost is the same as that of steel reinforcement, which is of epoch-making significance to replace steel reinforcementã??

1. Chopped basalt fiber Basalt fiber is a kind of inorganic fiber material. Chopped basalt fiber is an inorganic mineral fiber with a length of less than 50mm and can be evenly dispersed in cement concrete. 2. Characteristics of chopped basalt fibers (1) The naturalness of raw materials. Because the raw material for producing continuous basalt fiber depends on the natural volcanic extrusive rock, there are no ingredients harmful to human health except that it is inherently high in chemical stability and thermal stability. (2) Comprehensive performance. Basalt fiber is acid resistant and alkali resistant. It is both low temperature and high temperature resistant. It is insulated and insulated by heat and electricity. Its tensile strength is higher than that of large tow carbon fiber. Its elongation at break is even better than that of small tow carbon fibers. It has high compressive strength, shear strength and adaptability to aging, and has good comprehensive properties in harsh environment. (3) Low cost. The price of basalt fiber used in cement concrete is significantly lower than that of steel fiber and polyester fiber. (4) Natural compatibility. Basalt fiber is a typical silicate fiber, which is easy to disperse when mixed with asphalt concrete, cement concrete and mortar. The newly mixed basalt fiber concrete has stable volume, good workability and durability, and has superior high temperature resistance, anti-seepage, crack resistance and impact resistance.