Description A handmade soap made from pure natural ingredients helps to keep your skin fresh and smooth. Coconut oil handmade soap helps detoxicate, remove dead skin cells, moisturize skin, etc. It is made entirely by hand with natural, organic materials based on an ancient recipe very good for your health. It awakens your senses and makes you feel ready to embark on any adventures, both mental and physical, delivering true satisfaction of love, joy, and peace. Ingredients Virgin coconut oil, sorbitol, glycerine, base soap, water. Gluten free. Usages For facial wash: Wet your hands and rub the soap into a lather to massage over your face, then rinse with water. For bathing: Apply the soap to your body and massage, then rinse with water.
Laminating adhesive water based is a process of pressing two or more materials together to create a new material. This is done to create a material that addresses specific application requirements. Laminating adhesives are used to manufacture toilet paper with new functions by bonding different tissue together
We are exporter of Arabic Gum Or (Acacia Gum). Organic Gum Arabic (Acacia) is an emulsifier for flavor oils and essential oils, making them stable in water-based compounds. A 30/70 ratio of gum to water is recommended as the best starting point for a Gum Arabic solution. It can be mixed at a 6/1 ratio of gum to oil. It can be used in cosmetics, baking, and as a fiber supplement. Organic Gum Arabic (Acacia) is vegan, kosher, and gluten-free. The Sudanese Organic Gum Arabic Acacia Senegal Heshab is the best in quality all over the world.
A handmade soap made from pure natural ingredients helps to keep your skin fresh and smooth. Coconut oil handmade soap helps detoxicate, remove dead skin cells, moisturize skin, etc. It is made entirely by hand with natural, organic materials based on an ancient recipe very good for your health. It awakens your senses and makes you feel ready to embark on any adventures, both mental and physical, delivering true satisfaction of love, joy, and peace. Usages For facial wash: Wet your hands and rub the soap into a lather to massage over your face, then rinse with water. For bathing: Apply the soap to your body and massage, then rinse with water.
The bowls are made from coconut trunk, which is very hard but lightweight. There may be slight variations in size because each and every bowl is handmade. The bowls are super smooth, clean, and simple in design. All of the bowls are preserved with Eco-friendly water-based polish. The bowls can be used as kitchenware as well as hotel industry(restaurants) for food serving. The small bowls can be used for deserts and bigger ones can be used as heavy meals or kept fruits. The bamboo cup product line is one of the favorite products in homes, cafes, etc. You can use the product in combination with many different items such as coconut wood spoons and forks to use as food for your family or restaurants. Because the product is made from natural coconut wood, it is very safe for users. Fine art coconut wood products have a very natural color from the dark, perennial coconut wood grains, which are very durable and beautiful.
In order to meet the individual requirements of the clients, we offer accurately formulated range of Guar Gum. It is formulated using Guar plant and is very useful as thickening reagent for hydrogen binding and adsorption with cellulose and mineral surfaces. Our products ensure free flow and are non-ionic in nature. It gets readily devolved in the water and has moisture retention capacity. It is thickening emulsifying agent and is used in cheese, meat, desserts and different other poultry products. Features: • Consistent composition • Highly water soluble • Excellent quality Specifications: Particle size 60 mesh - 200 mesh Viscosity 200 cps - 7000 cps in Brook field and 20 Cps - 45 Cps in Fan 35 Viscometer
Fresh corn cleaning production line ,clean vegetable cleaning and air drying assembly production line, prefabricated vegetable processing equipment,different capacity customized . Machine features : 1.Universal adjustable nozzle, uniform spraying, stable without unhook, 360degree adjustable cleaning. 2.Circulating water tank, filter impurities in the product cleaning process to prevent clogging of the nozzle. 3.Automatic control, simple operation 4. Vortex air pump, strong wind, anti-seismic base, wear resistant. 5.Motor mute energy saving. Corn bubble cleaner production line also can process : Leaf vegetables, root vegetables, fruits, Chinese herbs, edible mushroom, aquatic products and seafood . Good business investing low cost high profit!
Roasted Guar Korma has been developed as a product free of antinutritive factors with balanced Amino Acid Profile. Suitable for Poultry, Swine, Ruminant and Aquaculture. Processed with heat and steam, inactivates harmful trypsin inhibitor which indirectly enhances protein and Amino acids digestibility in the product resulting in increased productivity of livestock and poultry. This process also reduces gummy substance by hydrolysing glactomannan and heat breaks cell walls resulting in higher digestibility of Guar Korma. The anti-nutritive trypsin inhibitor is present in both Soybean and Guar seed, but gets inactive when processed into Soybean meal and Guar meal respectively. We have two qualities of Roasted Guar Korma namely ULTRA and PREMIUM In Roasted Guar Korma ULTRA, the minimum protein content is 48 % and in Roasted Guar Korma PREMIUM, the minimum protein content is 55 %. The other nutritional and Amino Acid values of ULTRA and PREMIUM Roasted Guar Korma are listed below:- • Higher percentage of Crude Protein (CP) • Free From Aflatoxins • Higher Digestibility Index, due to the removal of anti-nutritive factors • More desirable and balanced Amino acid Profile • Higher Energy content and fat percentage • Lower percentage of less digestible Fibre • Higher Palatability, complete elimination of characteristic bean odour and taste. • Low content of Total Volatile Nitrogen (TVN) • Free flowing, uniform fine particle size with good fat and water binding ability NUTRITIONAL VALUES ULTRA PREMIUM Protein 48% – 50% 55% – 60% Metabolize Energy 2550 KCal/Kg 2700 KCal/Kg Moisture Less Than 8% Less Than 6% Fiber 6% – 8% 4% – 5% Fat 5.00% 5.00% Ash/ Sand Silica Less Than 2% Less Than 1% Calcium 0.55% 0.55% Phosphorus 0.68% 0.68% Available Phosphorus 0.19% 0.19% Urease Activity Less Than 1% Less Than 1% Pepsin Digestibility 85.00% 85.00% Trypsin Inhibitor Less Than 1 Less Than 1 Aflatoxins NIL NIL Salmonella NIL NIL E.Coli NIL NIL
Experience the farm-fresh difference of our Australian cream cheese. We craft our cream cheese with fresh milk & cream for a super smooth & soft texture that makes our cream cheese easy to use straight from the fridge. Our velvety soft cream cheese is expertly crafted at our specialist cream cheese site. Whether it's a sweet or savoury snack or for entertaining guests with a fresh homemade cheesecake, our Australian farm-fresh cream cheese will bring out the best in your next meal creation. 250g Spreadable Tub Excellent as a spread for breakfast, lunch or a quick snack any time of the day. Velvety smooth texture that makes it easy to spread on any sweet or savoury base. Ingredients: Milk, Cream (From Milk), Texturiser (Emulsifier (471), Milk Solids, Stabilisers (410, 412)), Salt, Starter Culture. Allergen Statement: Contains Milk Nutritional information Average Quantity per serving % Daily Intake* per serving Average Quantity per 100g SERVINGS PER PACKAGE: 10 SERVING SIZE: 25g Energy 310 kJ 4 % 1240 kJ Protein 2.2 g 4 % 8.9 g Fat - total - Saturated 7.1g 5.0g 10% 21% 28.3 g 20.0 g Carbohydrate - Sugars Less than 1.0g Less than 1.0g Less than 1% 1% 2.6 g 2.5 g Sodium 73 mg 3 % 290 mg
During last decade Guar has immerged as an important industrial raw material and Produced by man for thousands of years. India has been the single largest producer and exporter of Guar gum accounting for more than 80 percent of the global output and trade. Guar has now assumed a larger role among the domesticated plants due to its unique functional properties. India Ranks First in the production of guar which is grown in the North Western part of the Country which mainly includes the states of Rajasthan, Gujarat, Haryana and Punjab. Other main countries are Pakistan, U.S.A and Brazil The by-product of Guar Gum industry consisting of the outer seed coat and germ material is called guar meal. The Guar meal after gum Extraction is a potential source of protein and contains about 42% crude protein which is one and a half times more than the level of protein in guar seed. The protein content in guar meal is well comparable with that of oil cakes. It is used as a feed for livestock including poultry. Guar meal contains two deleterious factors i.e. residual guar gum and trypsin inhibitor, Toasting of Guar Gum improves its nutritive value in chicks. Toasted guar Meal can be used in limited quantity i.e. Up to 10% in Poultry diet. However it can replace groundnut cake by almost 100% in animal feeds. Guar Gum (Galactomanan) is a high molecular weight carbohydrate polymer made up of a large number of mannose and galactose unit linked together. The crude Guar Gum is a greyish white powder 90% of which dissolves in water. It is non ionic polysaccharide based on the milled endosperm of the guar bean whose average. Composition is: Hydrocolloid: 23% Fats: 40% Proteins: 34% The most important property of the Guar is its ability to hydrate rapidly in cold water to attain a very high viscosity at relatively low concentrations. Its specific colloidal nature gives the solution an excellent thickening power which is 6 to10 times thicker than that obtained from starch. It is stable over a wide range of PH and it also improves the flow ability and pump ability of the fluid. It is a superior friction loss reducing agent.
FH SERIES OF PRODUCTS: FH products are Pure nonionic derived the endosperm of guar polysaccharide (Cyamopsos tetragonolobus). The products are unique with ultra-high viscosity with fastest hydration characteristics as shown in Figure 1 below. Also, when added with other drilling components, to seawater, a KCl solution or other aqueous system, the product suspension disperses readily without lumping, even under low-shear conditions generating most of its full viscosity within just a few minutes. PRODUCT COMPATIBILITY: FH series of products are compatible with most of the chemicals and auxiliaries used in drilling operations. However, the products are not compatible with Arabic and Crystal gums. Also, in presence of borates they form elastic gel. PRODUCT APPLICATIONS: FH series of products are natural, high viscosity, fast hydrating non-Newtonian hydrocolloids with suitable cross linking components in diesel slurries and are versatile for continuous mix applications, where extremely fast hydration and subsequent viscosity development is required. They are excellent viscosifiers, stabilizers, thickeners and suspending agent for use in oil-drilling, workover fluids and several other oilfield applications like hydraulic fracturing, oil well stimulation, mud drilling, oil well capping, flocculent and liquid shoring etc. The product is used as a surfactant; synthetic polymer and deformer ideally suited for all rheological requirements of water based and brine based drilling fluids. Specifications:- PRODUCT : FH-35 FH-38 FH-42 CAS No. : 9000-30-0 9000-30-0 9000-30-0 Granulation : FINE FINE FINE APPEARANCE : OFF WHITE POWDER MOISTURE : 8% Max. 8% Max. 8% Max. PROTEIN (N X 6.25) : 5.0% Max 5.0% Max 5.0% Max ASH : 1.5% Max. 1.5% Max. 1.5% Max. ACID INSOLUBLE RESIDUE (A.I.R.) : 3% Max. 3% Max. 3% Max. CARBOHYDRATE (incl gum by difference) : 82% Min 82% Min 82% Min pH (1% Solution) : 5.5 ? 6.5 5.5 ? 6.5 5.5 ? 6.5 VISCOSITY : (0.48% Product in 2% KCL Sol. 2.5 mins mix @1500 RPM in waring blender) Fann 35sa Viscometer at 300 RPM, 25�C 3 Mins : 35 3 Min:38 3 Mins : 42 5 Mins : 37 5 Mins : 39 5 Mins : 43 30 Mins : 39 30 Mins : 42 30 Mins : 45 60 Mins : 40 60 Mins : 43 60 Mins : 47
Magnesia Bricks Description Magnesia Bricks are alkaline refractory materials. These products have over 90% magnesium oxide content and adopt periclase as the principal crystalline phase. Magnesia Bricks can be divided into two categories of Burnt Magnesia Bricks and Chemical Bonded Magnesite Brick. They have excellent performance of superior high temperature mechanical strength and volume stability. Magnesia Bricks can service in the high temperature of 1750.. They are ideal products for glass furnace application. Magnesia Bricks Features: It is a kind of alkaline refractory product with periclase as main phase magnesite-alumina spinel clinker as basic material. the product has such characteristics as good temperature vibration, good strength and volume stability in high temperature. Magnesia Bricks Application Basic open-hearth furnace for steelmaking Electric furnace bottom and wall Permanent lining of oxygen converter Non-ferrous metal metallurgy furnace Hyperthermia tunnel kiln Lining of rotary cement kiln Heating furnace bottom and wall Regenerative chamber of glass furnace Magnesia Bricks Properties High Refractoriness Good alkaline slag erosion resistance High apparent initial softening temperature Good thermal conductivity High thermal expansion Magnesia Bricks Manufacturing Process Burnt Magnesia Bricks are manufactured with magnesite clinker as the raw material and fired in the high temperature of 1550~1600 after smashing, burdening, mulling and molding. High-purity products can be fired in the temperature that over 1750. Chemical bonded magnesite brick is produced with certain chemical bonding through mixing, molding and drying.
Insulation Bricks
Refractory Fire Brick
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Ramming mass is commonly used in metallurgy, building materials, non-ferrous metal smelting, chemical, machinery and other manufacturing industries. Ramming mass is widely used in non-core intermediate frequency furnace and core induction furnace. As an intermediate frequency furnace ramming material, refractory ramming is applied to melt gray cast iron, nodular cast iron, malleable cast iron, vermicular cast iron, and cast alloy steel; to melt carbon steel, alloy steel, high manganese steel, tool steel, heat resistant steel, stainless steel, molten aluminum and its alloys; to melt red copper, brass, white brass, bronze and its alloys, etc. Induction furnaces are used for melting cast iron, mild steel and various alloy steels in foundries and making of steel in mini steel plants using sponge iron The refined high silicon, low iron quartz sand and quartz powder are selected and the fused quartz sand is added as the refractory material., with no slag, no crack, damp proof, convenience of repair, and the corrosion resistance, thus greatly improving the furnace service life span and the economic benefit.. Silica ramming mass can safely be used up to an operating temperature of 1600 deg C. Since it expands very little, it is superior to both alumina and magnesia refractories to resist thermal shocks Acid ramming material is the premixed ramming mass of the lining material. The acid ramming mass is used to smelt a series of metal materials such as ordinary steel and carbon steel. The lining practice best suited to a particular furnace depends upon the capacity and design of the furnace, operation practice adopted during making of a heat, and furnace output.
METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
