Cool Metal Brushed Pet Surface Panel Suppliers and Manufacturers

Guar Gum Split is refined endosperm derived from guar seed or cluster bean (cyamoperm tetragonoloba). Guar Splits are non-ionic polysaccharide galacomannan. Guar Gum Refined Split (Endosperm) is mechanically separated from guar seed which yields 28-30% of Refined Split. Guar beans are harvested and dried following the growing season. The beans are shelled from the pods, the germ and hull removed. The resulting guar splits are wet-milled into powder; the powder is graded by granulation and quality. Products are re-blended according to specification, bagged and marked. Guar Gum Split with its versatile inherent properties is used all over the globe with different utilities in many industries like Petroleum (Oil drilling), textile, printing, food pharma, cosmetic, toiletries paper, tanneries, mining, explosives, pet food etc. in powder form either directly plain Guar Gum Powder or in derived form. Uses : Guar Gum Split with its versatile inherent properties is used all over the globe with different utilities in many industries like Petroleum (Oil drilling), textile, printing, food pharma, cosmetic, toiletries paper, tanneries, mining, explosives, pet food etc. These industries use Guar Gum in powder form either directly plain Guar Gum Powder or in derived form. We provide quality Guar Gum Splits to quality manufacturer of Guar Gum Powder, which is their pre-requirement for manufacturing high quality Guar Gum. Specifications: Color Pale-white Gum Content 80-85% Splits 92-98% Mineral Matter (ASH) 1.5% max Fiber 1.5 – 2.0 % max Protein 5% Maximum Ether Soluble Substances 0.6% Maximum Acid insoluble ash (sand and/or silica) Traces Black Split 1% max Heavy Metals Nil Appearance Bright creamy yellow Packaging: Type of Bags Quantity HDPE Bags 50.00 Kgs Jumbo Bags 1000.00 Kgs

NOVEXIM Dear all customer Produced from freshly selected matured coconuts, Desiccated Coconut Low Fat is the dehydrated white coconut meat with lower fat content. Our products are unsweetened and do not contain any preservatives or additives. Desiccated Coconut Low Fat is most ideal for confectioneries and used as fillings, toppings and as ingredients especially for food manufacturers. Desiccated Coconut Low Fat is perfect for various industries that require the exhilarating feel of natural fibre in the product. As the product is more shelf stable compared to Desiccated Coconut High Fat, our Desiccated Coconut Low Fat is a good substitute for Desiccated Coconut High Fat. Bakeries Popularly used as topping for cakes and pastries; centre filling for buns; decoration for cakes; etc. Confectioneries Very ideal as fillings for candy bars; chocolate coating, etc. Desiccated Coconut Low Fat should be stored in a clean, cool and dry place away from direct sunlight, chemicals and free from odors, under an ideal room temperature of between 26C to 32C. Ingredient Fresh Coconut Meat Oil : 60 - 65 % Color Natural white Appearance Free from insect infestation, foreign bodies and metal. Flavour Mild, fresh and sweet characteristics of coconut with no off-flavour or odour Packing In 3-ply Kraft paper bags with inner sealed polyliner Size of Packing 25 kg net per bag Qty Per 20ft FCL 280 bags x 25 kg net (7 metric tons) Qty Per 40HC 560 bags x 25 kg net ( 14 metric tons)

NOVEXIM Dear all customer Produced from freshly selected matured coconuts, Desiccated Coconut Low Fat is the dehydrated white coconut meat with lower fat content. Our products are unsweetened and do not contain any preservatives or additives. Desiccated Coconut Low Fat is most ideal for confectioneries and used as fillings, toppings and as ingredients especially for food manufacturers. Desiccated Coconut Low Fat is perfect for various industries that require the exhilarating feel of natural fibre in the product. As the product is more shelf stable compared to Desiccated Coconut High Fat, our Desiccated Coconut Low Fat is a good substitute for Desiccated Coconut High Fat. Bakeries Popularly used as topping for cakes and pastries; centre filling for buns; decoration for cakes; etc. Confectioneries â?? Very ideal as fillings for candy bars; chocolate coating, etc. Desiccated Coconut Low Fat should be stored in a clean, cool and dry place away from direct sunlight, chemicals and free from odors, under an ideal room temperature of between 26C to 3C. Ingredient Fresh Coconut Meat Oil : 60 - 65 % Color Natural white Appearance Free from insect infestation, foreign bodies and metal. Flavour Mild, fresh and sweet characteristics of coconut with no off-flavour or odour Packing In 3-ply Kraft paper bags with inner sealed polyliner Size of Packing 25 kg net per bag Qty Per 20ft FCL 280 bags x 25 kg net (7 metric tons) Qty Per 40â?? HC 560 bags x 25 kg net ( 14 metric tons)

* Resting House --- For small animals, such as birds and hamsters. Provides small pets with luxury snooze spot. They love to have somewhere sheltered and private where they can nest and hide. * Activity Platform --- Comes with Ladder, keep your pet active, engaged and entertained in a way that satisfies his pure instincts. * 100% Coconut Fiber material --- The Birdhouse is made from one of strongest coconut husk materials ensuring its durability and safety. Round bird cages connects easily to cage with quick-link attachments - metal hook. And the charming colorful beads will attract the birds in the distance. * Perfect for Bird Nest --- Bird cages for lovebirds is sterilized 100% coconut and completely safe for your pet. * Multiple Usage --- Suitable for parrot, parakeets, finch, canary, songbird, hummingbird, Lovebird and other small birds. Apart from these, hamsters, rats, hermit crab, ferret love this product.

Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

We are supplier and exporter of Copper Slag. Copper slag is a low cost expendable abrasive suited for open blast cleaning and due to its low silica content it does not pose the health hazards created by silica sand. Its sharp, hard particles can provide a fast cleaning action and an excellent surface profile. It is available in various sizes Copper slag is abrasive blasting grit made of granulated slag from metal smelting processes (also called iron silicate). Copper slag abrasive is suitable for blast cleaning of steel and stone/concrete surfaces, removal of mill scale, rust, old paint, dirt etc. Suitable for SA-3, SA-2 and SA-2. Copper slag blasting media/grit is manufactured of the granulated slag of copper refineries, and used for blast-cleaning of metal surface. In different industries it is called different names abrasive powder, grit, copper slag grit, mineral grit, grinding grains, etc.

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.

EnzoPlast TS 8 is a Chemically Modified, Vegan, Gluten-Free, Plant- based, Non-GMO oxidized tapioca starch. EnzoPlast TS 8 is characterized by its exceptional functional properties such as low viscosity, high stability, clarity, film forming, low temperature stability and binding properties. EnzoPlast TS 8 is widely used in bakery products, frozen foods, dairy products, confectioneries, breading and coating applications, etc., It is 100% naturally made which does not have any preservatives and Mono sodium Glutamate (MSG). APPLICATIONS ï?· EnzoPlast TS 8 is used as stabilizer in milk products, ice cream desserts, puddings, fillings, etc.,It is also used in the production of flavoured yoghurts, flavoured milk drinks, whipped cream, low fat cream, etc., ï?· EnzoPlast TS 8 can also be used as fat-mimetic and partial replacement of casein in cheese products with improved stretchability and hardness ï?· EnzoPlast TS 8 is recommended for salad and vegetable sauces, salad dressings, sugar syrups, sauces for canned meat and vegetables, mayonnaise, soups, puddings, fruit filling for confectionery products, jellies, fruit paste candy and soft gummies ï?· In baking industry, EnzoPlast TS 8 expands and improve physical possessions and physical properties of dough, increases its capability to hold gases FROZEN FOODS EnzoPlast TS 8 is used in frozen foods, refrigerated or canned foods, generally for thickening, temperature stability and control the flow in the purpose food. EnzoPlast TS 8 are used for improved adhesion and improved stability, reputedly because of covalent bonding with protein on the substrate surface. FUNCTIONAL PROPERTIES EnzoPlast TS 8 forms highly thixotropic pastes with stiff texture, which is related to its gelling capability Low gelatinization temperature and viscosity, clarity, and soft gel texture are attributes of EnzoPlast TS 8 used in breading and related applications When heated in water, EnzoPlast TS 8 form clear fluid sols. On cooling, however, the sols made by cooking EnzoPlast TS 8 is more stable or resistant to thickening and forming gels or pastes EnzoPlast TS 8 is used in formulated products. They also are used in starch batters and in breaded foods, where they improve adhesion of the batter to meat and fish Gum confections made with EnzoPlast TS 8 have longer shelf life, better gelling characteristics, increased clarity, better taste, and quicker drying Used in batters and breading for coating various food stuffs, in confectionery as binders and film formers, in dairy products as texturizers EnzoPlast TS 8 is often used for coating, sealing, batter binding, emulsification, and dough conditioning in baking and other food products.

Main features: 1. You can choose to use a single saw or a double saw for product stability, or a single saw for unstable products 2. Ensure the hygiene of the meat and ensure a smooth cutting surface 3. Waterproof design for quick cleaning 4. According to different uses, frozen meat, lamb chops, steak, fish 5. Adopting human-machine interface and intelligent operation panel 6. 30 sets of memory functions can be set 7. Feeding adopts servo motor, with high precision 8. The conveyor belt can be removed for cleaning Paramters : cutting thickness 1-50mm ,material thickness under 15cm . capacity 8-15times/min ,can adjustable.

Vintage Embroidered Metal Zip Brushed Jacket

PET Flakes Green Mixed Yellow Hot Washed Plastic Scrap Material For Sales MATERIAL PET Flakes green mixed yellow, hot washed CATEGORY PET TYPE Flakes GRADE green mixed yellow, hot washed SPECIFICATION "PET Flakes green mixed yellow (3-5%), hot washed. Size: 4~14mm; PVC

Technical characteristics of SkyLite polycarbonate awning: * Using materials are SkyLite polycarbonate panels with UV resistance, high light transmission, sound insulation, good heat insulation. * Negative link between the frame and the plate, minimizing the screw holes on the surface, avoiding the leak through the screw hole and high aesthetics. Simple to transport and install, save time in construction and installation. * Environmentally friendly, safe for users.

Laminated glass is one kind of safety glass , and when glass breakage, glass fragments adhering to the interlayer, it can be against forced entry, and avoid fragment damage.EVA laminated glass, it can be laminated with large range of inserts including PET film, polycarbonates, wood veneer, metal, paper, stones, screen mesh and so on, it is good choice for inner decoration.

JHG is professionally offering all various of high quality laminated glass: 1) PVB laminated glass Colour includes clear/milk/bronze/grey/blue/green/black PVB film thickness is 0.38/0.76/1.14mm or thicker Both standard size and customized sizes available 2)Sentryglass Plus(SGP)laminated glass SGP bring more safe,more transparent for construction ,the film includes 0.89/1.52/2.28mm and thicker mainly used for glass floor,glass step,glass fin,curtain wall Max size is 18000mm length 3)EVA laminated glass It can be laminated with large range of inserts including PET film,polycarbonates,wood veneer,metal,paper ,stones,screeen mesh ,and so on ,it will bring mulrirusinous choice for inner decoration.

Bentonite as is a particular kind of clay derived from volcanic ash and consists mainly of montmorillonite with minor amount of illite, kaolinite, cristobalite and other minerals. Bentonite has strong colloidal properties and, when in contact with water, increases its volume several fold by swelling, forming a tixotropic, gelatinous substance. Main uses of Bentonite take advantage of these colloidal properties. The main characteristics of Bentonite is its decolorizing power, that is the property of the earth to absorb selectively certain pigments rather than others according to the characteristics of the product to be decolourized(acidity, oxidation degree, origin and biological state etc.) APPLICATIONS For Drilling Fluids Pilling Binder (e.g. foundry-sand bond, iron ore pelletizer) Purifier Electrical Earthing Agriculture Cosmetics, Paper, Paints and Ceramics Absorbent (e.g. pet litter), and As a Groundwater Barrier. We CEMENTATION acquire own mines for Bentonite in India. We supply Bentonite for industrial, manufacturing, construction and drilling applications. Our production or supply capacity is more than 250,000 TPA. At CEMENTATION a special attention is given while mining Bentonite as the materials physical and chemical properties are depended upon the interference of the other metal ions present in the soil. Once the material sourced from mines are transferred to our factory and are left for drying in an open land to reduce moisture up to the desired level. After the drying process and other checks are done our skilled manpower will do a sorting of the material and then after the material goes to pulverizes for grinding to desired mesh size and are packed according to customers requirement. Our laboratories are well equipped to meet the needs of the diverse markets we serve.