T1000 primary injection test set is the model featured with light weight and 2 minutes output time at 1000A. This ideal primary injection test set with LCD display,quick control button and rotating mouse is very easy and convenient to operate. Features 2 minutes continuous output at 1000A Flexible control over output, such as manual, ramp, etc Independent Aux DC supply In-built multi-meter facility Typical CT testing functions are also included Weight : 30kg
1. Operating Pressure: 100, 200, 700, 1500, 3500 (KPa) 2. Overpressure: 300 %FS 3. Output/Input impedance: 5í+2 (Kª+) 4. Offset: 0í+40 mV 5. FOS: 100í+40 mV 6. Nonlinearity: í_í+0.5 %FS 7. Reoatability, hysteresis: í_í+0.1 %FS 8. Offset TC: í_í+8 í-10-4/íµ.FS 9. SpanTC: í_í+5 í-10-4/íµ.FS í_ú¡23 í-10-4/íµ.FS ú¡40í½125 íµ Note: A:Measured when supplied by 5VDC/1mA. B:The best operating line defined by national measurement standard. C:full operating temperature. D:25íµ,5VDC,65%RH unless otherwise noted.
Characteristic: Efficiency grade: 0.1/0.2/0.5 International standard signal input: 0-5v/0-10v/1-5v, 0-10ma/0-20ma/4-20ma Output internal signal with high load capability: 5v/0-10v/1-5v, 0-10ma/0-20ma/4-20ma and so on U3: 0-75mv P3: dc5v O4: 0-5v U4: 0-2.5v P4: dc15v O5: 0-10v U8: customer choose P8: customer choose O6: 1-5v A1: 0-1ma O8: customer choose A2: 0-10ma A3: 0-20ma A4: 4-20ma A8: customer choose Example: Eg1: input: 0-5v Accessorial power supply: 24vdc Output: 4-20ma Model: din 1x1 iso-u1-p1-o1 Eg2: output: 4-20ma Accessorial power supply: 24vdc Output: 4-20ma Model: din 1x1 iso-a4-p1-o1 Dimension:62*51*83mm
L-signal measurement, and industrial-site signal isolation and long-term transmission and so on. Products include power supply isolation, signal isolation, linearization, a/d conversion and rs-485 serial communication circuit module. Each serial port can connect maximum 256 pcs of isoad series modules, means of communication using character communication protocol or modbus rtu communication protocol. Its instruction set compatible with the adam modules, the baud rate is set by the user, with other manufacturers control module hanging in the same rs-485 bus, to facilitate host programming. Iso ad series of products are based on single chip of intelligent monitoring and control systems, all the user sets such as the calibration value, address, baud rate, data format, checksum status and other configuration information is stored in nonvolatile memory eeprom inside. Isoda series of products according to industry standard design, manufacture, signal output / communication interface isolation, can withstand 3000vdc isolation voltage, anti-interference ability, high reliability. Operating temperature range: - 45 ~ +80. Model selection Isoad16 u(a) - Vin/iin U1: 0-5v a1: 0-1ma U2: 0-10v a2: 0-10ma U3: 0-75mv a3: 0-20ma U4: 0-2.5v a4: 4-20ma U5: 0-¡¨¤ 5v a5: 0-¡¨¤ 1ma U6: 0-¡¨¤ 10v a6: 0-¡¨¤ 10ma U7: 0-¡¨¤ 100mv a7: 0-¡¨¤ 20ma U8: customized a8: customized Communication interface 485: output is rs-485 interface 232: output is rs-232 interface Dimensions:58*87.5*59mm
24 bit accuracy, have been calibrated all signal input before ex factor. Also, users can programme himself, two input types must be same when testing two signals. Communication software: Communication interface: 1 standard rs485 interface or 2 standard rs232 interface Communication agreement: standard ascii, modbus, can make network communicate With plc, rtu or watch software. Data format: 10 bit, 1 start bit, 8 data bits, 1 stop bit. Communication address (0~255) and baud rate (300\600\1200\2400\4800\9600\19200\ 38400bps), max. Communication distance: 1200m, connect by both twists shiled cable. ¡¨¤ 15kv esdprotection, communication response time is less than 100ms. Anti jamming: Set checksum according to need. Its inside contains momentary bate diode, can Restrain surge impulse, protect modules. Model selection: Iso 4021a u(a) - Input voltage or current signal U1: 0-5v a1: 0-1ma U2: 0-10v a2: 0-10ma U3: 0-75mv a3: 0-20ma U4: 0-2.5v a4: 4-20ma U5: 0-¡¨¤ 5v a5: 0-¡¨¤ 1ma U6: 0-¡¨¤ 10v a6: 0-¡¨¤ 10ma U7: 0-¡¨¤ 100mv a7: 0-¡¨¤ 20ma U8: customized a8: customized Communication interface 485: output is rs-485 interface 232: output is rs-232 interface 232/485: output is rs-232orrs-485interface, rs232/485 switchover freely Size:62*51*83mm
Mode of operation : Periodicity running (3 phase full load or 2 phase 6kvA full loading 1 hour, no loading 1 hour), continuous running: at least 4 hours. ï??ï? Wave form distortion rate: â?¤5% (no load line voltage). ï??ï? setting range of output voltage: when 125Hz, 20 240V Continuous adjusting ( stabilivolt running under given voltage condition). ï??ï? Noise ï¼?â?¤108dB(A) (Voice level) The CT, VT Test we can supplied , including CT, VT Routine Test, CT, VT Accuracy , Error Measurement Test, we have rich experience and perfect after-sale service. If you are interested in , you can call us at any time.
CE-D-type three-phase AC intelligent digital display is a programmable function, automatic measurement, digital display, the cumulative power, the standard analog, switch, RS485 output and other functions of the integrated power parameter detection instruments. With high precision, good electromagnetic compatibility, good looks and so on. Can be set according to demand voltage, current, power, power factor and any one of the corresponding standard analog output; any set voltage, current limit, hysteresis, upper limit alarm or lower limit alarm and other parameters; Free to set the communication address (0-255), display ratio and so on. Accuracy class: 0.5, 0.2 (current, voltage) The maximum display: 9999 Maximum resolution: Voltage: 0.1V Current: 0.001A Input: 500V * 5A Analog output: 0-5V 4-20mA Communication output: RS485 (baud rate: 9600bps; data format; start bit 1, data bit 8, stop bit 1, no parity) Switch output: a group of relay contact output, contact capacity 5A / 250VAC Function settings: switch control value, back to the difference, the working mode; analog output mode and input mode; the address; display variable ratio; screen display parameters of the switch. Auxiliary power: 85 ~ 265V Power consumption: â?¤ 4.5VA Isolation voltage: power supply / input / output between â?¥ DC2.5KV / min.1mA Pulse group interference: 1.6KV Power against lightning surge: 4KV Shell material: ordinary plastic Face plate installation, behind the wiring Dimensions: 96 Ã? 96 Ã? 110mm Installation hole size: 91 Ã? 91mm
To meet the requirement of the network system to the power, santakups has developed a new generation ups - bpro offline series. It adopts 32bits data-bus microprocessor with robust processing power that is capable of detecting and controlling quickly and accurately all movement of ups to ensure product high reliability. Owe to the use of the double-conversion circuit design, the power used by load is the pure sine wave power by stabilizing voltage and stabilizing frequency and noisy signals filter. Specificationú¦ model b500a/600a b1000a/1200a Max capacity(va) 500va(300w) 1000va(600w) Rated capacity 600va(360w) 1200va(720w) Input commerical power range 145vac-280vac Avr range 165vac-270vac Frequency 50hzía10% Output commerical power sine-wave Inversion simulated sine-wave Frequency commercial power supply:shared frequency with the commercial inversion state:50hzía0.5 Avr voltage range 220vacía10%(auto-sensing) Transfer time typical:5ms(including detection time) Protection overload ups automatically shutdown if overload exceeds 150% of normal value for 30 seconds and 180% for 3 seconds Tel/fax/modem no Short circuit ups output is cut off immediately or input circuit breaker protection Alarm battery back-up beeping sound every 4 seconds when the input is cut off Battery low voltage beeping sound every 1 seconds when the input is cut off Overload continuously beeping sound when overload Battery type sealed, maintenance-free lead acid Capacity (12v, 7ah)x1 (12v, 7ah)x2 Recharge time 8 hours to 90% of full capacity Back-up time typical 20 min(halfload) Battery protection automatic self-test, discharge protection
Nominal Scale: Gauge pressure: 35KPa,100KPa,250KPa,600KPa,1MPa,1.6MPa,2.5MPa Absolute Pressure: 100KPa,250KPa,600KPa, 1MPa,1.6MPa,2.5MPa,6MPa, 10MPa,25MPa,40MPa,60MPa Offset: ¡Ü30mV@1mA Span Output: ¡Ý30mA(¡Ü30KPa) ; ¡Ý60mV (other nominal scale) Nonlinearity: ¡À0.25%F.S. Power Supply: 1 mADC (constant), 5V (optional) Zero Temperature Coefficient: ¡À0.1%F.S./ ¡æ Sensitivity Temperature Coefficient: ¡À0.1%F.S./ ¡æ (¡Ü35KPa) ¡À0.1%F.S./ ¡æ (other nominal scale) Overload Capacity: 2 times nominal scale(¡Ü10MPa) 1.5times nominal scale(£¾10MPa) Bridge Resistance: 5 (1¡À20%) K¦¸ Operating Temperature: -45¡æ ¡« +100¡æ Chip Size: 2700¡Á3450(um)
Byj series stepper motor Model 35BYJ46 Rated voltage 12VDC Number of Pole 4 Speed Variation Ratio 1/85.25 Stride Angle 7.5fp /85.25 DC resistance 130ohmf+7%(25k) Idle In-traction Frequency >500Hz Idle Out-traction Frequency >800Hz In-traction Torque >78.4mN.m(120Hz) Self-positioning Tor >39.2mN.m insulated resistance >10ohm(500V) insulated electricity power 600VAC/1mA/1s Insulation grade A Rise in Temperature
Switching Mode Power Supply (SMPS) S-100 Series (Single) Low price and high reliability 105f¦ output capacitor AC input power suitable for the world High efficiency and low operation temperature Soft-start current can reduce the AC input impact effectively With short-circuit and overload protection 100% full-load burning test Installed with EMI filter, minimum wave. 1) Switching Power Supply (SMPS) Output: Dc voltage/Rated current:5V/20A or7.5V/13.6A or10V/10A or12V/8.5A or15V/6.7A or 18V/5.6A or24V/4.5A or27V/3.7A or48V/2A 2) Switching Power Supply (SMPS) Input: Voltage range: 85 ~ 132vac / 170 ~ 264vac selected by switch 255 ~ 370vdc AC input frequency: 47 - 63Hz AC current:2.4A/115VAC 1.2A/230VAC Inrush current (max.):cold start 30A/115VAC 60A/230VAC Leakage current:
Switching power supply Switching Mode Power Supply (SMPS) S-40 Series (Single) Low price and high reliability 105 output capacitor AC input power suitable for the world High efficiency and low operation temperature Soft-start current can reduce the AC input impact effectively With short-circuit and overload protection 100% full-load burning test Installed with EMI filter, minimum wave. 1) Switching Power Supply (SMPS) Output: Dc voltage/Rated current:5V/8A or12V/3.5A or15V/2.8Aor 24V/1.8A 2) Switching Power Supply (SMPS) Input: Voltage range: 85 ~ 264VAC 120 ~ 370VDC AC input frequency: 47 - 63Hz AC current: 1.2A/115VAC 0.6A/230VAC Inrush current (max.):cold start 15A/115VAC 30A/230VAC Leakage current:
DRONE QUADCOPTER RC MenPack Jammer up to 1000m CT-4035-UAV CT-4035-UAV Menpack Directional Antenna Drone UAV 102W 5 Bands Jammer up to 1000m Man Pack Anti-Drones UAV 5 Bands High power 102W 1 - 2 Hours Built-in Battery Directional Jamming range 400 -1000 Meters 4 Bands in One Directional Antenna Spec 5 bands 4 in 1 Directional Antenna 2.4GHz: 20W In Direction antenna 2.4GHz: 20W In Direction antenna 5.8GHz: 2 W in direction antenna GPS L1 40W In Direction antenna 433Mhz 25w or 2.4ghz 20W or 868-920Mhz 25W in One Omni Antenna TOTAL 102W Adjustable output power for each band Battery can support 1-2 hours operating Support use while battery charging Adjustable output power Jamming range: Radius 400 1000 Meters Four Bands in One Directional Patch Panel Antennas Weight 14 Kg, Raining proof man pack. Cover Most Commercial Used Drones UAVs like is Dji Phantom 4, Phantom 3 Professional, Advanced, Standard series, Inspire Series. 1 Year warranty, Taiwan design quality, made in Hong Kong
DR-45/24 1.Low price and high reliability 2.105íµ output capacitor 3.AC input power suitable for the world 4.High efficiency and low operation temperature 5.Soft-start current can reduce the AC input impact effectively 6.With short-circuit and overload protection 7.Compact size, light weight 8.100% full-load burning test 9.Installed with EMI filter, minimum wave Model Specification DR-45-5 DR-45-12 DR-45-15 DR-45-24 DC output voltage 5V 12V 15V 24V Output voltage error (Note2) % í+1% í+1% í+1% Rated output current 5A 3.5A 2.8A 2A Output current rage 0-5A 0-3.5A 0-2.8A 0-2A Wave and noise(Note3) 100mVp-p 200mVp-p 240mVp-p 480mVp-p Inlet stability(Note4) í+1% í+1% í+1% í+1% Load stability(Note5) í+1% í+1% í+1% í+1% DC output power 25W 42W 42W 48W Efficiency 72% 77% 77% 80% Adjustable range for DC voltage 4.75-5.5V 10.8-13.2V 13.5-16.5V 21.6-26.4V AC input voltage range 85í½264VAC/47í½63HZ;120í½370VDC Input current 1.5A/115V 0.75A/230V AC impulse current Cold-start current 30A/115V 60A/230V Leakage current
CT-24100525 2.4Ghz 5Ghz High Power 125W portable case Jammer up to 2500m The most power model with 100W on 2.4Ghz and 25W on 5Ghz The effective blocking range is 800 to 2500 meters. Do not blocking GSM Cell phones. Working time is 24 hours without stop. 2 Band/Antenna Frequency: 1. 2.4Ghz 1 x 100W 2. 5GHz 1 x 25W (Can be 5.5-5.9Ghz, 5.7-5.9Ghz, 5.5-6.1GHz, 5.1-5.9GHz, 5.0-5.5Ghz) TOTAL : 125W Adjustable Output Power from Max to 0 (OFF) VSWR over protection for each modular Battery: No Battery , Order option battery - 45AH LiFePO4 + 500$ Power supply: AC110 or 220-240V /DC 27V Jamming Range Radius 800m to 2500m+ The jamming distance will be varied depending on the signal strength and location. Good cooling system with heat sink and two 2 big fans inside, low noise Dimension: CT-24100525 518 x 428 x 228 mm (Case only) Working time: Without the time limit, may continue to work Antenna External Omni 750mm long or Directional Patch Panel Antennas Weight: 30Kg 1 Year warranty, Taiwan quality made in Hong Kong R&R GROUP INTERNATIONAL Taipei Taiwan, Hong Kong, Dubai UAE
Temperature rise test panel for domestic switch Specifications Input supply : 230v ac + / - 10% , 50 hz single phase with mcb protection. Output : current source 0 to 50 a max Digital voltmeter : 3-1/2 digit 0 to 300v Voltage drop indicator with range selector. Digital temperature indicator with 12 channels. Current controller for maintaining the output current at pre-set value. Ct range selector for accurate measurements. Description The test panel is made to suit the specification as mentioned in is : 3854 of 1997 for temperature rise test. The test panel broadly comprises of : 1. Ac constant current source ( true rms ) for 50 amps max / 5v. 2. Universal servo controller, for controlling the output current with the help of motorised variac Assembly. 3. Digital ac voltmeter to read the primary voltage of the power transformer. It helps to eliminate the Possibility of hunting of motor with the help of primary tap selector switch. 4. Digital temperature indicator controller - 12 channels - with thermocouples, to read the temperature rise At different parts of the switches. 5. Digital ac voltmeter with terminals and three ranges - 0.2, 2.0 & 20 v to measure the voltage drop Across the switch terminals while passing the specific current. 6. Range selector switch for ct to measure more accurately the current for lower as well as higher range. 7. Push buttons for test on / off with output indicating lamps. 8. Mains on mcb 2p / 10 a.
The SIM7000E is Tri-Band LTE-FDD and Dual-Band GPRS/EDGE module solution in a SMT type which supports LTE CAT-M1(eMTC) and NB-IoT up to 375kbps data transfer. It has strong extension capability with rich interfaces including UART, USB2.0, GPIO etc. The module provides much flexibility and ease of integration for customer's application. The package of SIM7000E is compatible with SIM900 and SIM800F. AT commands of SIM7000E are mostly compatible with SIM800F. This also maximizes the investments of customers, and enables a short time-to-market. It is designed for applications that need low latency, medium throughput data communication in a variety of radio propagation conditions. Due to the unique combination of performance, security and flexibility, this module is ideally suited for M2M applications, such as metering, telematics, asset tracking, remote monitoring ,E-health , mobile pos terminals and sharing bike. General features - Tri-Band FDD-LTE B3/B8/B20 - GPRS/EDGE 900/1800Mhz - Output power - GSM900: 2W - DCS1800: 1W - Control Via AT Commands - Supply voltage range: 3.0V~ 4.3V, Typ: 3.8V - Operation temperature: -40 to +85 - Dimensions: 24 X 24 X 2.6mm - Weight: 3.0g - GNSS (GPS,GLONASS and BeiDou/Compass, Galileo, QZSS) Specifications for Data transfer - LTE CAT-M1(eMTC) - Uplink up to 375kbps, Downlink up to 300kbps - NB-IoT - Uplink up to 66kbps, Downlink up to 34kbps - EDGE Class - Uplink up to 236.8Kbps, Downlink up to 236.8Kbps - GPRS - Uplink up to 85.6Kbps, Downlink up to 85.6Kbps Other features - USB Driver for Microsoft Windows XP/Vista/7/8 - USB Driver for Windows CE/Mobile - USB Driver for Linux/Android - Firmware update via USB - TCP/IP - PPP - SMS - EMAIL - FTP/HTTP/SSL - VoLTE* - FOTA* Interfaces - USB2.0 x1 (high-speed) - UART x2 (7-wire UART and 2-wire UART interface multiplex from GPIO) - SIM card x1 (1.8V and 3V) - I2C x1 - GPIO x5 - ADC x1 Consumption - Power off: 7uA - PSM: 9uA - Sleep: 1mA - Idle: 11mA
The SIM7000E is Tri-Band LTE-FDD and Dual-Band GPRS/EDGE module solution in a SMT type which supports LTE CAT-M1(eMTC) and NB-IoT up to 375kbps data transfer. It has strong extension capability with rich interfaces including UART, USB2.0, GPIO etc. The module provides much flexibility and ease of integration for customer's application. The package of SIM7000E is compatible with SIM900 and SIM800F. AT commands of SIM7000E are mostly compatible with SIM800F. This also maximizes the investments of customers, and enables a short time-to-market. It is designed for applications that need low latency, medium throughput data communication in a variety of radio propagation conditions. Due to the unique combination of performance, security and flexibility, this module is ideally suited for M2M applications, such as metering, telematics, asset tracking, remote monitoring ,E-health , mobile pos terminals and sharing bike. General features * Tri-Band FDD-LTE B3/B8/B20 * GPRS/EDGE 900/1800Mhz * Output power - GSM900: 2W - DCS1800: 1W * Control Via AT Commands * Supply voltage range: 3.0V~ 4.3V, Typ: 3.8V * Operation temperature: -40â?? to +85â?? * Dimensions: 24 X 24 X 2.6mm * Weight: 3.0g * GNSS (GPS,GLONASS and BeiDou/Compass, Galileo, QZSS) Specifications for Data transfer * LTE CAT-M1(eMTC) - Uplink up to 375kbps, Downlink up to 300kbps * NB-IoT - Uplink up to 66kbps, Downlink up to 34kbps * EDGE Class - Uplink up to 236.8Kbps, Downlink up to 236.8Kbps * GPRS - Uplink up to 85.6Kbps, Downlink up to 85.6Kbps Other features * USB Driver for Microsoft Windows XP/Vista/7/8 * USB Driver for Windows CE/Mobile * USB Driver for Linux/Android * Firmware update via USB * TCP/IP * PPP * SMS * EMAIL * FTP/HTTP/SSL * VoLTE* * FOTA* Interfaces * USB2.0 x1 (high-speed) * UART x2 (7-wire UART and 2-wire UART interface multiplex from GPIO) * SIM card x1 (1.8V and 3V) * I2C x1 * GPIO x5 * ADC x1 Consumption * Power off: 7uA * PSM: 9uA * Sleep: 1mA * Idle: 11mA
6040 co2 laser engraving machine 40w 4060 co2 laser engraver Features This machine adopts imported linear guide and dsp system control software. The machine has stable performance and applicable for different industries. It is the ideal choice for non-metal processing industry. Dy-13 Reci Co2 Laser Power Supply for 1400mm RECI W4 100watt CO2 laser tube Features: 1.This� DY 13� laser power supply adopts zero current and half bridge soft switch circuit, it makes the power supply have high efficiency and quick response speed. Thus it is easy to match with RECI W4 100W CO2 laser tube. 2.This� 100watt� laser power supply is easy to be controlled, it is suitable to High or Low level signal. The TTL level can control start or stop of laser output. While the power supply has emergency protection switch which can indicate water through and ventilation. 3.The laser output power� of this DY13 CO2 power supply� can be adjusted by 0-5V analog signal or PWM signal. 4.This� DY-13 CO2� laser power supply has open circuit protection function. When protective earthing is good, the laser power supplycan be in open circuit status during short time. This function can protect power supply when laser tube burst. 5.Aging test:Each laser power supply must pass this test which is taken at 60 degree centigrade for 12 hours in full load status. And the power supply must start and stop at each 7 seconds for 500 times. In this way we can ensure the laser power supply is qualified. 6. This DY-13 100W CO2 laser power supply uses ordinary H/L/P/G/IN/5V interface as laser control signal and it uses blue aluminum case. Specification: Input AC Voltage AC220V or AC110V Input DC Voltage DC 300V or DC150V Input AC Frequency 47-440Hz Max. Output Voltage 40KV Max. Output Current 28mA(Depends on Laser tube) Efficiency 91% Over Current Protection 130% of Max. Current Open circuitProtection Yes (For short time) Cooling Fan Cooling Voltage Range of High Level Control Not Less Than3V Voltage Range of Low Level Control Not More Than0.8V Working Temperature -30 - +65 Degree Centigrade Humidity 20-85%RH(No Dew) � Withstand Voltage Input-Output AC1500V/MinNot More Than10mA Input-Shell AC1500V/MinNot More Than10mA Output-Shell Connected Insulation Not Less Than 50MOHM(DC500V) Leakage Current Not Less Than 1mA(AC220V)Not More Than 0.5 mA(AC110V) Shock Resistance Amplitude: 0.5mm, Frequecy:10-55Hz, 3D Dretion:2 Hours MTBF Not Less Than30,000hours Full Load 60 Degree Centigrade test 12Hours 7 Seconds Start/Stop Test 500 Times Dimension(LXWXH) 270x160x80mm
System description: Introducing new epa 300, a portable standard meter Used for the measurement of the three phase power And the energy. Various measuring features combined with its easy operation concept provide the greatest possible flexibility for a comprehensive testing of metering installations on site. Features: 1. On line calibration with external ct 2. Direct current option up to 10a 3. Accuracy < 0.2% 4. Large lcd display. 5. Pulse input & output 6. Sensor for pulse out led Functions: 1. Power and energy measurement of active, reactive and apparent energy 2. Frequency-, phase angle- and power factor measurement. 3. Error measurement on electric meters. Actual values measurement: 1. Rms values of all voltage and current phases 2. Currents for all 3 phases 3. Frequency and power factor - cos ϕ. 4. 3 phase - kw, kwh, kva, kvar, kvarh 5. Percentage of the measurement error with pulse input. Technical data: 1. Power supply: 85-250vac, 50/60hz. 2. Voltage measurement: 0……300v 3. Voltage measurement accuracy: < 0.1% 4. Current measurement: 50ma ….10a (for direct measurement)1 a…1000a (for measurement with clip -on ct) 5. Current measurement accuracy: direct measurement
