Description Two component, air drying, high solids, Epoxy coating. The product has the advantage of epoxy resin composition with speciality pigment, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to completely wet the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. The composition has been balanced to a convenient mixing ratio by volume with excellent application characteristics. The low solvent content reduces the problem of lifting of the paint film and adhesion failure by blistering and pin holing. This assures a stable long term performance. Recommended Use :- It is mainly recommended in those areas where blasting is impractical or impossible. Uses include steel structures in Industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. Physical Data COLOUR : Selected industrial shades FINISH : Semi glossy SOLIDS BY VOLUME : 80 + 2% THEORETICAL SPREADING RATE : 10 sq.mt. / ltr. at a recommended DFT of 80 FLASH POINT : Base : Above 25C Hardener : Above 25C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30�°C) : SURFACE DRY : 4 hours FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data :- MIXING RATIO : Base : Hardener ( As per our recommendations) APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 RECOMMENDED DFT : 75-100 mic. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats.
Description Two components, air drying, high build Epoxy primer. The product has the advantage of epoxy resin composition with specialty pigments, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to be completely wet and provide maximum intimacy with the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. With the high solids and less solvent content of the coating the risk of lifting, blistering, pin holing is reduced, and thus the risk of adhesion failure is minimized. Recommended Use :- It is recommended for steel structures in industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. Physical Data COLOUR : Selected Industrial shades FINISH : Matt SOLIDS BY VOLUME : 63 + 3% THEORETICAL SPREADING RATE : 8.4 sq.mt / lt at a recommended DFT of 75 FLASH POINT : Base : Above 25C Hardener : Above 25C DRYING CHARACTERISTICS (At 30C & 65% Relative Humidity) : HARD DRY : 16 - 18 hours FULL CURE : 7 days SHELF LIFE : Base: 6 months Hardener: 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible than manual cleaning by mechanical methods like wire brush, emery paper, hand / power tools, etc. to achieve St-2 / St-3 cleaning standards of Swedish specification. The surface should be free from moisture, oil, dust and dirt and should be absolutely dry before painting. Removal of loose rust is a must. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation ) POT LIFE : 2 hours at 30�°C APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 RECOMMENDED DFT : 75-100 �µ. OVERCOATING INTERVAL : MIN : 8 hrs. MAX : 24 hours (In case it is exceeded, the surface should be roughened byemery scuffing) OVERCOATABILITY : Epoxy, PU, Chlorinated Rubber and Synthetic Enamel intermediate &finish coat.
Description Two component, air drying, high solids, Epoxy coating. The product has the advantage of epoxy resin composition with speciality pigment, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to completely wet the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. The composition has been balanced to a convenient mixing ratio by volume with excellent application characteristics. The ZERO solvent content reduces the problem of lifting of the paint film and adhesion failure by blistering and pin holing. This assures a stable long term performance. Recommended Use :- It is mainly recommended in those areas where blasting is impractical or impossible. Uses include steel structures in Industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, water tank, pipelines etc. for application on tank exteriors and interiors, structural steel, pipelines, machineries, vessels, etc. Physical Data COLOUR : Selected industrial shades FINISH : Semi glossy SOLIDS BY VOLUME : 80 �± 2% THEORETICAL SPREADING RATE : 10 sq.mt. / ltr. at a recommended DFT of 80 �µ FLASH POINT : Base : Above 25�°C Hardener : Above 25�°C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30�°C) : SURFACE DRY : 4 hours FULL CURE : 7 days HARD DRY : Overnight SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data :- MIXING RATIO Base : Hardener ( As per our recommendations) : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Airless Spray POT LIFE : 2 - 3 hours min at 30�° C RECOMMENDED DFT : 75-100 mic. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU
Titanium plates with flow fields are essential components used in electrolyzers for various industrial applications. These plates, made from corrosion-resistant titanium materials, are designed with intricate flow field patterns to optimize the electrochemical process of water electrolysis. Electrolyzers equipped with titanium plates and flow fields play a crucial role in industries such as hydrogen production, water treatment, and chemical processing. Specifications: Material: Titanium (Grade 2 or Grade 5) Plate Thickness: 0.5-30 mm Flow Field Pattern: Serpentine, Interdigitated, or Customizable Dimensions: 90*90mm Customizable Features Enhanced Mass Transfer: The flow field pattern on titanium plates promotes efficient mass transfer of gases and electrolytes, ensuring uniform distribution and maximizing the electrochemical reaction efficiency. Improved Current Distribution: The optimized flow field design helps achieve uniform current distribution across the electrode surface, minimizing localized effects and improving electrolyzer performance. Extended Lifespan: Titanium's corrosion resistance and durability contribute to the longevity of electrolyzers, reducing maintenance costs and downtime. Customizable Designs: Titanium plates with flow fields can be customized to meet specific electrolyzer requirements, allowing for optimized gas and electrolyte flow patterns tailored to the application. Applications Hydrogen Generation: Electrolyzers equipped with titanium plates and flow fields are extensively used in industries involved in hydrogen production, enabling the production of clean and sustainable hydrogen gas for fuel cell applications, energy storage, and industrial processes. Chlor-Alkali Industry: Titanium plates find applications in the chlor-alkali industry, where electrolysis is employed to produce chlorine, caustic soda (sodium hydroxide), and hydrogen. The plates' resistance to highly corrosive electrolytes and durability make them suitable for this demanding application. Desalination: Titanium plates with flow fields are utilized in electrochemical desalination processes, where they play a vital role in the removal of salt and other impurities from seawater, making it suitable for drinking water or industrial use. Electrosynthesis: Titanium plates are used in electrosynthesis applications, where electrochemical reactions are employed to synthesize various chemicals and pharmaceutical intermediates. The flow field design on the plates helps facilitate efficient mass transfer and uniform current distribution, enabling controlled and precise electrochemical reactions.
Dipotassium Phosphate Food Grade/ Tech Grade/ Dipotassium Phosphate (DKP): Chemical Property: Dipotassium phosphate (DKP), also known as potassium phosphate dibasic, has the chemical formula K2HPO4. It is a salt that exists as a white, crystalline powder or granules. DKP is highly soluble in water, which facilitates its use in various applications. It contains two potassium (K+) cations and one hydrogen phosphate (HPO4^2-) anion in its chemical structure. Applications: Dipotassium phosphate is utilized in a range of industries due to its properties as a nutrient source, pH regulator, and food additive. Food and Beverage Industry: DKP is commonly used as a food additive in the food and beverage industry. It acts as a buffering agent to control acidity and pH levels in various products, including processed foods, beverages, and dairy products. It also works as a sequestrant, helping to improve the stability and texture of certain food items. Nutritional Supplements: In the production of nutritional supplements, DKP can be used as a source of both potassium and phosphorus, essential nutrients for human health. These supplements might target individuals with specific dietary needs or deficiencies. Bakery and Baking Powder: DKP is sometimes used in baking powder formulations. It interacts with other ingredients, like baking soda (sodium bicarbonate), to release carbon dioxide gas and leaven baked goods. pH Buffering and pH Control: Due to its ability to regulate pH, DKP is used in various industrial processes where maintaining a specific pH range is crucial. This can include water treatment, chemical manufacturing, and certain laboratory applications. Pharmaceuticals and Medicine: DKP might be used in pharmaceuticals and medicine for its pH-regulating properties, as well as its potential use as a source of essential nutrients in certain formulations. Water Treatment: In water treatment processes, DKP can be used to adjust pH levels and reduce the corrosiveness of water. It's also used to inhibit the formation of scale and deposits in pipes and equipment. Laboratory and Research: DKP is utilized in laboratory settings for various purposes, including as a component in buffer solutions used in experiments requiring specific pH conditions. Dipotassium phosphate's versatility in balancing pH levels, providing essential nutrients, and enhancing stability makes it a valuable ingredient in multiple industries. As with any chemical, its application should be handled with care to ensure proper dosing and to mitigate potential environmental impacts. FORMULA: K2HPO4 CAS NO: 7758-11-4 / 16788-57-1 EINECS: 231-834-5 ORIGIN: China Port of Loading: Xiamen MOQ: 17MT ETD: 10 Days Customization: Yes Package: 25kg/1000kg/1250kg/1300kg Bags
Diammonium Phosphate DAP Food Grade/ Tech Grade/ Electronic Grade Diammonium Phosphate (DAP): Chemical Property: Diammonium phosphate (DAP) is a compound with the chemical formula (NH4)2HPO4. It is a highly soluble salt that appears as a white, crystalline powder. DAP contains two ammonium (NH4+) cations and one hydrogen phosphate (HPO4^2-) anion in its structure. This composition provides a source of both nitrogen and phosphorus, making DAP a valuable fertilizer and nutrient supplement. Applications: Diammonium phosphate finds applications primarily in agriculture as a fertilizer, but it also has uses in other industries: Agriculture and Fertilizers: DAP is one of the most commonly used fertilizers worldwide. Its high nitrogen content supports plant growth and leaf development, while phosphorus promotes root growth, flowering, and fruiting. The ammonium component of DAP also contributes to pH control in soil, which can be important for optimizing nutrient availability to plants. Nutrient Supplement: DAP can be used as a nutrient supplement for both plants and animals. In animal feed, it provides a source of nitrogen and phosphorus, essential for growth and overall health. Industrial Processes: DAP is utilized in various industrial applications. For instance, it's used as a fire retardant and flame inhibitor in certain materials due to its ability to release ammonium compounds that resist combustion. Water Treatment: In water treatment processes, DAP can be used to reduce pH levels, control scale formation in pipes, and adjust the alkalinity of water. Yeast Nutrient: In the brewing and fermentation industries, DAP is used as a nutrient for yeast during the fermentation process. It provides nitrogen necessary for yeast growth and alcohol production. Laboratory and Research: DAP is sometimes employed in laboratories for specific applications, such as in the preparation of buffer solutions or as a source of nutrients in cell culture media. Explosives Manufacturing: While not a common application, DAP has been used in the production of certain explosives due to its chemical properties. DAP's versatility stems from its dual nutrient content of nitrogen and phosphorus, making it valuable for promoting plant growth and supporting various industrial processes. When using DAP, it's important to consider proper dosing and application methods to ensure optimal results and minimize any potential environmental impacts. FORMULA: (NH4)2HPO4 CAS NO: 7783-28-0 EINECS: 231-987-8 ORIGIN: China Port of Loading: Chongqing MOQ: 25MT ETD: 25-30 Customization: Yes Package: 25kg/1000kg/1250kg/1300kg Bags
Monopotassium Phosphate Food Grade/ Tech Grade/Agriculture Grade 100% water soluble Monopotassium Phosphate (MKP): Chemical Property: Monopotassium phosphate (MKP), also known as potassium dihydrogen phosphate, has the chemical formula KH2PO4. It is a soluble salt that forms white, crystalline powder or granules. MKP is highly soluble in water, which makes it easy to dissolve and apply as a nutrient solution in various applications. It contains potassium (K+) cations and dihydrogen phosphate (H2PO4-) anions, providing a source of both potassium and phosphorus. Applications: Monopotassium phosphate is widely used in various industries due to its properties as a fertilizer, pH buffer, and food additive. Agriculture and Fertilizers: MKP is commonly used as a high-quality fertilizer in agriculture. It provides essential nutrients to plants in the form of potassium and phosphorus. Potassium is essential for overall plant health, aiding in water regulation, nutrient uptake, and disease resistance. Phosphorus is crucial for root development, flowering, and fruiting. MKP's solubility ensures that plants can quickly access these nutrients. Hydroponics and Fertigation: MKP is a favored choice in hydroponic and fertigation systems, where nutrients are supplied to plants through water. Its solubility allows for precise nutrient control, and its dual contribution of potassium and phosphorus supports optimal growth and yield in controlled environments. pH Buffering: MKP is used as a pH buffer in various applications, such as in the formulation of pH-adjusting solutions. It can help maintain a stable pH environment, which is important in industrial processes, water treatment, and laboratory settings. Food Additive: In the food industry, MKP is used as a food additive for its role in regulating acidity and pH levels. It can be found in processed foods, beverages, and baking products. Additionally, it's used in some food preservation methods. Laboratory and Research: MKP is used in laboratories for preparing solutions with controlled pH levels. Its use extends to biochemical and molecular biology experiments where a specific pH environment is crucial for reactions. Fire Extinguishing Agents: In some cases, MKP is used in fire extinguishing agents due to its ability to suppress flames by releasing water and creating a barrier to combustion. Monopotassium phosphate's versatility as a nutrient source, pH regulator, and buffer makes it valuable in various industries. However, its application should be managed carefully to ensure proper dosing and minimal environmental impact. FORMULA: KH2PO4 CAS NO.: 7778-77-0 EINECS: 231-913-4 ORIGIN: China Port of Loading: Chongqing MOQ: 25 MT ETD: 7 Days Customization: Yes Package: 25kg/1000kg/1250kg/1300kg Bags
TMAP with N:P:K 12:61:0, Food Grade, Tech Grade and electronic Grade Monoammonium Phosphate (MAP): Chemical Property: Monoammonium phosphate (MAP) is a chemical compound with the formula NH4H2PO4. It is a white crystalline powder that is highly soluble in water. MAP is an acidic salt with a low pH, making it suitable for applications where acidic conditions are desired. It contains both ammonium (NH4+) and phosphate (H2PO4-) ions, making it a source of both nitrogen and phosphorus nutrients. Applications: Monoammonium phosphate has a wide range of applications in various industries due to its properties as a fertilizer, fire retardant, and food additive. Agriculture and Fertilizers: MAP is commonly used as a fertilizer in agriculture. It serves as a source of both nitrogen and phosphorus, essential nutrients for plant growth. The high solubility of MAP ensures that plants can readily absorb these nutrients, promoting healthy root development, flowering, and fruiting. It is particularly beneficial for crops that require early-season nitrogen and phosphorus supplementation. Fire Retardant: MAP is also used as a fire retardant in both the agriculture and forestry sectors. When applied to plants or materials, it releases ammonium and phosphate compounds that can act as flame inhibitors, reducing the flammability of the treated material. This makes it valuable for preventing and controlling wildfires and protecting valuable crops. Food Additive: In the food industry, MAP is used as a leavening agent in baking. It reacts with baking soda (sodium bicarbonate) to produce carbon dioxide gas, which helps dough rise and gives baked goods their desired texture. It is commonly found in baking powders and self-rising flour. Industrial Applications: MAP is used in various industrial processes, including water treatment. It can be used to reduce the pH of water and control scale formation in boilers and cooling systems. It is also used in some metal cleaning and finishing operations. Nutrition Supplements: MAP is sometimes used in the formulation of nutritional supplements, especially in cases where a controlled release of both nitrogen and phosphorus is needed, such as in plant fertilizers for hydroponic systems or aquarium plant care. pH Adjustment: Due to its acidic nature, MAP can be used to adjust the pH of various solutions, including in some laboratory settings and industrial processes where maintaining a specific pH range is crucial. Monoammonium phosphate's versatility stems from its ability to provide essential nutrients, modify fire behavior, and contribute to various chemical reactions across multiple industries. However, its usage should be managed responsibly to ensure optimal results and minimal environmental impact. FORMULA: NH4H2PO4 CAS NO.: 7722-76-1 EINECS: 231-764-5 ORIGIN: China Port of Loading: Chongqing MOQ: 25 MT ETD: 25-30 Days Customization: Yes Package: 25KG/ 1000KG/1250KG/1300KG Bags
Sodium carbonate is one of the important chemical raw materials, widely used in light industrial daily chemical, building materials, chemical industry, food industry, metallurgy, textile, petroleum, national defense, medicine and other fields, as raw materials for the manufacture of other chemicals, cleaning agents, detergents, also used in photography and analysis fields. It is followed by metallurgy, textiles, petroleum, national defense, medicine and other industries. The glass industry is the largest consumer of soda ash, consuming 0.2 tons per ton of glass. In the industrial soda, mainly light industry, building materials, chemical industry, accounting for about 2/3, followed by metallurgy, textile, petroleum, national defense, medicine and other industries. 1. The glass industry is the largest source of soda ash consumption, with 0.2t of soda ash consumed per ton of glass. Mainly used for float glass, picture tube glass, optical glass and so on. 2, used in chemical industry, metallurgy, etc. The use of heavy soda ash can reduce alkali dust flying, reduce raw material consumption, improve working conditions, but also can improve the quality of products, while reducing alkali powder on refractory erosion action, prolong the service life of the kiln. 3, as buffer, neutralizer and dough improver, can be used in pastry and noodle food, according to the production needs of appropriate use. 4, as detergent for wool rinsing, bath salt and medical use, tanning alkali agent in leather. 5, used in the food industry, as a neutralizer, leavening agent, such as the manufacture of amino acids, soy sauce and noodle food such as steamed bread, bread, etc. It can also be mixed into alkali water and added to pasta to increase elasticity and ductility. Sodium carbonate can also be used to produce monosodium glutamate 6, color TV special reagent 7, used in pharmaceutical industry, as acid antidote, osmotic laxative. 8, used for chemical and electrochemical oil removal, chemical plating of copper, aluminum etching, aluminum and alloy electrolytic polishing, aluminum chemical oxidation, phosphating after sealing, process rust prevention, electrolytic removal of chromium coating and chromium removal of oxide film, also used for pre-plating copper, plating steel, plating steel alloy electrolyte 9, metallurgical industry used as smelting flux, flotation agent with beneficiation, steel and antimony smelting used as desulfurizer. 10, printing and dyeing industry used as water softener. 11, leather industry is used for degreasing raw skin, neutralizing chrome tanning and improving the alkalinity of chrome tanning liquid. 12. The reference of acid in quantitative analysis. Determination of aluminum, sulfur, copper, lead and zinc. Urine and whole blood glucose were tested. The cosolvent of silica in cement was analyzed. Metallographic analysis, etc.
White Super-High Strength Fast Setting Rapid Hardening High Belite Sulpho Aluminate Cement These are white hydraulic binders (referred to as white super-high strength double-fast cement)with super-high strength, fast setting and rapid hardening properties, made from active (or inactive) mixed materials such as fast setting rapid hardening high belite sulpho aluminate cement clinker with low content of ferric oxide, moderate amount of gypsum (or industrial by-product gypsum), slag and other active (or inactive) hybrid materials with fine grinding, and the code is BS - WSF. Specification item value Warranty 1 Year After-sale Service Online technical support Project Solution Capability Others Application construction Design Style Contemporary Model Number White Super-High Strength Fast Setting Rapid Hardening High Belite Sulpho Aluminate Cement Feature Decorative Type Calcium sulfoaluminate cement Hardening Feature Extra Rapid Hardening Heat of Hydration Low-Heat Strength Grade(Mpa) 42.5 INITIAL SETTING TIME 15mins FINAL SETTING TIME 45mins Technical Data: Physical Properties: Advantages: 1/ Fast setting, Rapid hardening, high strength; 4h compressive strength can reach 15Mpa, 102Mpa after 28d, suitable to make the high strength products. 2/ Micro expansion, low dry shrinkage, the length change is very small. Dry shrinkage rate is just 1/8 of Portland cement. 3/ Have very good anti-corrosion property in sulfate, chloride, magnesium salt and seawater. Corrosion resistance coefficient 1. 4/ High impermeability, permeation height is 1/5 of Portland cement. 5/ High frozen resistance property, can get the strength of critical intensity of cold in 2h 3h. 6/ Low hydration heat release 7/ PH value is under 10.0 for GRC products. 8/ High whiteness value, the Hunter whiteness is above 75. 9/ Re-alkali resistant performance is good 10/ Can be mixed with Portland cement in a proper ratio, can greatly reduce the shrinkage of Portland cement, reduce the cracks. Application area: 1/GRC 2/Decoration mortar 3/Interior and exterior wall putty 4/Artificial stone and floor 5/Decorative concrete 6/Building reinforcement 7/ HPC and RPC 8/Rush projects and constructions, projects in winter. 9/ High early strength Non-shrinkage grouts
Basic Infomation Model NO.: A-01 CAS No.: 13463-67-7 Formula: TiO2 EINECS: 236-675-5 Colour: White Appearance: Powder Transport Package: Woven Bag Specification: 25kg/bag HS Code: 32061110 Product Description A-01 is an anatase titanium dioxide pigment manufactured by the sulfate process. The grade is a fine, dry, white powder with excellent whiteness, strong covering power, high coloring power and good weathering resistance. It's widely used in coatings(Indoor), chemical fiber, plastics(PVC, Masterbatch), paper-making, shoe materials, glass beads and other fields. Physical Properties Property Standard TiO2 Content % 98.5 Color (Compared with standard sample) No lower than Tinting strength % 100 Loss of 105 C % 0.5 Oil absorption g/100g 23 Water-soluble salt content % 0.5 pH value of aqueous suspension 6.5 ~ 8.0 Residue % (0.045mm Sieve pore) 0.05 Resistivity of aqueous extract �©.m 20 Dispersity % 60 Application Coatings(Indoor), chemical fiber, plastics(PVC, Masterbatch), paper-making, shoe materials, glass beads and other fields. FAQ Q1: Are you a manufacturer or trading company A1: We are a professional manufacturer of titanium dioxide and barium sulfate, Ideal New Materials is the sales company and our Q3: When will you deliver A3: It usually takes 5-10 days if the materials are in stock, or 15-20 days if the materials are not in stock, it is based on quantity. Q4: Is there any possible to use my appointed label or package A4: Sure. If needed, we'd like to use label or package according to your requirement. Q5: What about the packing A5: We usually provide woven bags of 25kg/bag. Of course, if you have special requirements for them, we will do it according to your requirements. Q6: How can you guarantee the goods you offer is qualified A6: We always believe honesty and responsibility are basis of one company, so whatever products we provide for you all are high qualified. We provide a factory inspection report for each shipment, and customer's inspection before shipment is supported.
What is a vacuum fryer machine? The equipment uses heat conduction medium to dehydrate and dry food under negative pressure,the processed food has very low water content and oil content, crisp but not greasy.To some extent, it preserves the original shape, color, aroma and taste of fruits and vegetables completely, and is rich in vitamins, minerals, fiber and other nutrients. It has the characteristics of low sugar, low salt, low fat and low heat. Model:XSD-WX, XSD-30,XSD-60,XSD-120 Capacity:10-100KG per hour Working temperature:70â??-120â??(adjustable) deoiling method:inner deoiling under the vacuum state deoiling speed :0-300r/min(adjustable) Material :vacuum kettle,inside storage tank:stainless steel 304 outside of pot body storage area has insulation layer,material is stainless steel matte plate control system microcomputer automatic control(manual/automatic) Application 1.Fruits: Apple, Banana, Pineapple, Peach, Cranberry, etc. 2.Vegetables: Carrot, Pumpkin, Snap bean, Sweet potato, Taro, Potato, Garlic, Green Pepper, Onion, etc. 3.Nuts: cashew nut, Peanut, etc. 4.Seafood, meat etc. Fish, shrimp, shellfish,chicken etc 5.Cooked wheaten food fried dough twist,crust of cooked rice,caramel treats etc Our Advantages 1.Low temperature fried, healthy food and low cost.It can prevent the loss of nutrients in the food at high temperature,effectively maintain the natural color and flavor of the food, and reduce the processing cost than the ordinary frying method. 2.Low oil content,good taste and no greasy. The oil content rate of food is below 15%. 3.Well stored and concentrated, the food is crisp and delicious 4.Rapid water evaporation and short drying time. 5.Safe, reliable and easy to operate. 6.Famous brand components. Electrical parts and operating parts are made of world advanced brand components. 7.Good expansion effect and high product rehydration 8.Long product shelf life. � Shandong Qinglei Environmental Technology Co.,Ltd is an equipment manufacturer integrating design, production and assembly. Our products include heat exchangers, heat exchange units, pressure vessels, storage tanks, TCU temperature control systems, reactors, distillation towers, VOCS purification and recovery systems, vacuum� frying machine. If you need any of them,please donâ??t hesitate to let me know,I will reply you ASAP.
Introduction DTWL - 30G high precision thermostatic chamber ( - 30 65- 30 75 30 80 )is a specially designed constant temperature chamber with air as the heat transfer medium. It has the technical characteristics of high temperature control accuracy, good uniformity of temperature field and small fluctuation. There are many temperature measuring instruments that cannot contact the liquid constant temperature source, and are not suitable for calibration in a constant temperature bath. The emergence of a high - precision temperature box solves the calibration problem of such instruments and fills the gap of the constant temperature source and provides a complete solution. Features Using constant temperature liquid bath technology, the temperature field is more constant Temperature control adopts liquid bath constant temperature and other plate heating technology. After the liquid medium is controlled to a constant temperature in the constant temperature bath, it is circulated to the outside of the working cavity. Through the heat radiation method, the temperature of the working cavity is constant and uniform. The cooling method has a qualitative leap in temperature indicators. Intelligent Integration of measurement technology and internet of things technology, wifi remote control, making measurement easier. High - definition touch screen control, multi - touch, greatly improve the user experience. One - key start, full automatic control, shorten the training period of measurement personnel. Timing switch machine, remote switch machine, save time and improve verification efficiency. Wide temperature range High - precision temperature box series products can provide constant temperature environment within the range of - 40 100 Meet JJF1407 - 2013 WBGT Index Meter Thermometer Calibration Regulations Meet JJF1366 - 2012 Temperature Data Acquisition Instrument Calibration Specification High precision air bath constant temperature source Using high - precision temperature control sensor, with imported temperature control table did not achieve high - precision temperature control, low indication deviation Excellent quality The shell adopts thick plate phosphating, passivation, spraying, anti - corrosion, anti - rust, salt spray resistance; Liner adopts SUS304 High - precision sensor, using imported high - precision platinum resistance sensor Function HD touch Using high - resolution capacitive screen, the display is clearer, multi - touch support, in line with customer mobile phone touch operation habits. Wifi control Mobile phone pad remotely set the temperature, start and stop the device, read the current temperature value and fluctuation degree and other device status.
We offer the world best organic pepper from kampot, Cambodia. Weâ??ve got three main peppers 1. Black pepper 2. Red pepper 3. White pepper Black pepper Kampot black pepper delivers a strong and delicate aroma. Its taste, which can range from intensely spicy to mildly sweet, reveals hints of flower, eucalyptus and mint. This black pepper suits all kind of dishes and distinguishes itself in particular with grilled fish. Kampot peppersâ?? specificities come from the mildness of their spice, the freshness and complexity of their aromas and their exceptionnal lingering taste. Kampot pepper can be used in every day cooking, but excels when used in seafood cookery, it is also a "super food". Why not try something different? A Cambodian speciality is to make a dip from a combination of salt, palm sugar, Kampot pepper and lime. It couldnâ??t be simpler to put together, equal amounts of each and just a squeeze of lime Red pepper These unique red Kampot peppercorns produce a moderate heat that gradually builds in the mouth. Intense, flavourful and complex, these peppercorns pair beautifully with pasta, poultry, produce and pastries Harvested when the fruit is fully mature and has taken a red colour on the vine. The peppercorns are sun-dried for a few days and acquire a black colour with a deep maroon taint. This pungent pepper is very rare. Pepper is best purchased as whole peppercorns, as freshly ground pepper is vastly superior to the ready ground powder. Whole peppercorns retain their flavour indefinitely but quickly lose their aroma and heat after grinding. Peppercorns can be easily ground in a peppermill or pestle and mortar, and is best ground directly onto food. With hot food it is best to add pepper well towards the end of the cooking process, to preserve its aroma. Peppercorns are seasonal with harvesting taking place from February to May. White pepper Kampot red and white peppers are extremely rare due to the difficulty in harvesting fully mature pepper. Only a few hundreds of kilos are produced each year. Obtained by soaking the red berries in water for a few days, Kampot white pepper develops an intense bouquet and delicate aroma. Its strong spicy taste carries notes of fresh grass and lime.
Suitable for shower bath installation, double holes unfold Install. single handle independent switch. The product has three functions giving water(A. top shower, B. hand shower, C. outlet faucet) .The functions giving water is controlled by the outlet faucet, easy to operate and have superior performance. High purity brass main body, stainless steel tub, with 8 inch (20cm) ABS (engineering plastics) top shower. Chrome-plated. Soft silicone water particle easy to cleaning scale, flow uniformity. Bent tube up and down smoothly in 300mm height(suitable for different people and easily adjusted) .Slide shower bracket up and down smoothly and can be rotated multi-angled . With 1.5m stainless steel flexible hose and single function hand shower. Using high quality materials ABS( engineering plastics) ,chrome plated. Service conditions: 1)The working pressure of the products is 0.05MPa-0.9MPa 2)The temperature is no more than 85° when supply hot water. 3)Don't use vapor when supply hot water. 4)Please don't connect the cold and hot pipe inversely 5)The working temperature is more than 0° 6) Please take note of the strength of the wall when installing due to the heavy weight. 7)The distance of the embed cold and hot water pipe joint center is 150 ± 20mm. Applications: Home faucets Rain shower faucets, Chain hotel faucets, commercial faucet, , household faucets etc. Specifications: Material: #59-1Brass diverter, stainless steel tube,zinc alloy handle Cartridge: Hain-Yo Ceramic cartridge, Guarantee 5 years no leakage Surface treatment: Chrome-plated, other plating available, including brush nickle, red bronze etc. The thickness of plating: 8~12um Salt Spray Testing: General plating: 24hours/Acid;120hours/neutral Acid Plating: 48hours/Acid;240hours/neutral Water Pressure Testing: 0.05-0.9MPA Cartridge Life time: 500,000 cycles Quality Guarantee: 5 years Quality Guarantee Drawing: Please contact us to get Hardware needed for mounting: Along with the faucet A.I.: Along with box packing
Hammer mill crusher Application Hammer mill crusher is suitable for mid-hard and light erosive Materials, whose pressureresistance strength is no more than 100Mpa and humidity lower than 15%, suchas coal, salt, chalk, gypsum, blocks, lime Stone, etc. Hammer mill crusher Operating Principle The main working part of hammer crusher is rotors with hammer. The rotors consist of main shaft, disk, pin shaft and hammers. The motor drives the rotors to rotate quickly in the crushing cavity. Raw Materials enter the crusher through the feed opening and are stricken, impacted, cut and ground by the high-speed hammerto small size. There is a screening plate under the rotor, so that Materials with size smaller than the screen mesh will be screened out and others are left tobe further hammered and ground until reach the st and ard size. The size of the final product can be adjusted by changing the screening plate. The gap between therotors and the screening plate can also be adjusted according to different requirement. Hammer Mill Design The major components of hammer mill, shown in the picture, include: - a delivery device is used to introduce the material to be ground into the path of the hammers. A rotor comprised of a series of machined disks mounted on the horizontal shaft performs this task. - free-swinging hammer that is suspended from rods running parallel to the shaft and through the rotor disks. The hammer carries out the function of smashing the ingredients in order to reduce their particle size. - a perforated screen and either gravity- or air-assisted removal of ground product. Acts to screen the particle size of the hammer mill to ensure particles meet a specified maximum mesh size. Feeder Design Materials are introduced into the paths of the hammers by a variable speed vein feeder. This type of feeder can have its motor slaved by a programmable controller to the main drive motor of the hammer mill. The operational speed of the feeder is controlled to maintain optimum amperage loading of the main motor. Screen Design The amount of open area in hammer mills screen determines the particle size and grinding efficiency. The screen must be designed to maintain its integrity and provide the greatest amount of open area. Screen openings (holes) that are aligned in a 60-degree staggered pattern optimize open area while maintaining screen strength. This method will result in a 40 percent open area using 3.2 mm (1/8 inch) holes aligned on 4.8 mm (3/16 inch) centers. Read more: evelyn@cncharcoalmachine.com
Corn Flakes Processing Line produces cereal flakes, both plain or coated. The twin-screw extrusion technology is at the core of this very flexible and scalable process. Main Equipment: Corn Flakes Processing Line produces cereal flakes, both plain or coated. The twin-screw extrusion technology is at the core of this very flexible and scalable process. This technology is ideal to meet the market demands and breakfast cereal manufacturing: many raw materials are eligible with coating recipes such as sweet syrups, honey, chocolate and other compositions. Technical Features: We share our process knowledge to process healthy and balanced products made with wholegrain cereals or including a mix of multi-grains like corn, wheat, oats, rice, barley, rye, Buckwheat or barley... Corn Flakes Extruder is used to produce consistently high quality products while keeping the same organoleptic characteristics as traditional flakes. System Advantage: Advantages of Corn Flakes Processing Equipment:  1. Quicker process : 15 to 20 minutes against 8 to 10 hours with the traditional batch process 2. Variety of recipes: diversity of raw materials (cereals, tubers, various ingredients �?�) and particle size used (from flour to semolina), wide range of coatings 3. Possibility to add functional and tasty ingredients : natural color, salt, fiber, vitamins, minerals, emulsifiers, 4. Possibility to process multigrain flakes, for example by introducing other grains directly during extrusion. 5. Possibility to upgrade the production line to process expanded or coextruded breakfast cereals 6. Productive: continuous and automated process, quick start up and stop, fast and easy changeovers and with easy cleaning and maintenance procedures; 7. Cost effective : intensified transformation process generating savings in raw materials as well as energy and water, easy maintenance, hygienic design, compact design with less floor space Application Scope: Technical Parameters of Corn Flakes Equipment: Model Capacity Power Dimension QL-65 120-150kg/hr 180kw 40 x 5 x 3m QL-70 200-260kg/hr 260kw 45 x 5 x 3m
Bathroom Shower Arm Detailed Description of the Shower Arm Extension: Brass bathroom accessories shower arm brass chrome plated wall-mounted,brass bathroom fittings various from the shape of slim round and square.Top shower arm is stay in corrosion resisting,brass chrome arm is made from No.59 brass casting on the main body,five layer plated.Brass extender is used for the Rain Shower Head connection.Bathroom accessories brass chrome hardware is various and welcome by world customers. brass shower arm Name: Bathroom Shower Head arm Brand:Handy Type:HN-H46 Material:Brass, surface Finished:Chrome The thickness of electro plating: 8 to 12 micron Salt spray testing for 2 kinds of electro plating as follows: a) General plating: 24 hours / Acid; 120 hours / neutral b) Acid plating: 48 hours /Acid; 240 hours / neutral Guarantee time: 10 year MOQ: 200 pieces Packaging: Standard export package or Customized Payment by: T/T, Western Union Delivery: Shenzhen CHINA, 30 days after payment. Fields of applications:Home using Top shower, hotel head shower. Single shower head, Concealed shower. Hn H46 Competitive Advantage: 1. High-quality and Eco-friendly faucets: All faucets use #59 brass, durable ceramic cartridge, advance environmental protection electro-plated technology, more conducive to environmental protection. 2. Our faucets come with 10-year warranties. 3. Supply laser LOGO on faucet`s handle or body, paste products label on our neutral color box with our brand printing or OEM brand printing, MOQ for OEM of color box printing is 1000unit. 4. Individual Package: Individual package and 12 units packed with carton. 5. Easy Assembly: All hardware needed for mounting is included with faucet, assembly instruction along with every unit box.Single hole basin faucets 6. 100% of our products are tested before shipment. 7. Simples ready in 3 to 7 days. Shower arm manufacturer and its qualification, comply with ISO9001:2015. ISO9001-2015 FAQ: Q: How about payment terms? A: 30% TT deposit + 70% TT before shipment Q: How long is the fastest delivery time? A: Within a week if we have stock parts.
Stainless steel vibratory screen Brief introduction of double fly powder screening machine: Double fly powder screen is one of the main products of Henan Techeng Machinery Manufacturing Co., Ltd., after many years of production and sales precipitation, its design and production technology has been mature and exquisite, and has a good reputation in the customers and industry. Double fly powder, also called calcium magnesium powder, is also called calcium and magnesium powder, mainly calcium and magnesium. It is usually used as a filler and is usually used as a filler. The fineness of good quality double fly powder is within the range of more than 225-1200 eyes. It is used in professional full batch and seams, plaster based materials, widely used in artificial floor tiles, rubber, plastics, paper, paint, paint, ink, cable, construction supplies, food, medicine, textile, and feed. Toothpaste and other daily chemical industry. Double fly powder screening machine is used to screen materials similar to double fly powder. It is widely used in chemical industry (Industrial drugs, cosmetics, paints, Chinese medicine powder, etc.), food industry (sugar powder, starch, salt, rice powder, juice, etc.), metal, metallurgical mining (aluminum, lead powder, copper powder, ore, alloy powder, electrode powder, manganese dioxide, electrolytic copper powder, quartz sand, etc.) Pollution treatment (waste oil, wastewater, dyeing and finishing wastewater, auxiliaries, activated carbon, etc.). The working principle of the double fly powder screen dividing machine: The double fly powder sieving machine consists of two vertical vibration motors, a common motor and a vibration exciter. The upper and lower ends of the vibration source are equipped with an eccentric hammer. The two ends of the hammer are different in configuration. When the exciting source is rotating, it produces horizontal, vertical and oblique three dimensional motion, and then transfers the motion to the screen surface. Therefore, the double fly screen machine also belongs to the three dimensional vibration screen, adjusting the phase angle between the upper and lower ends of the screen, which can change the movement track of the material on the screen, so as to achieve the purpose of fine screening. Characteristics of double fly powder screen dividing machine: 1, small volume, no space, easy to move, simple to operate and easy to clean. 2, high efficiency, exquisite and durable design, any powder and mucus can be sieved. 3, mesh is not blocked, powder is not flying, it can be screened to 500 mesh or 0.028mm. 4, impurities and coarse materials can be automatically discharged and can be continuously operated. 5, the design of the unique space grid is long, and the screen time is long. It is easy to change the network, and it takes only 3-5 minutes. 7, the sieve can reach up to five layers, and three layers are recommended.
With the years of experience, we are offering a wide range of qualitative Vista Catasoft to our customers. Our Vista Catasoft is a special cement additive that is synthesized our laboratories to assist cement industry in rising mill output, improving efficiency of grinding, decreasing electricity cost and reducing pack or silo set. Vista Catasoft is basically an organic complex amine salt ethoxylated in presence of cement strength improving chemicals and flow enhancers through â??SOL GELâ?� technology â?? FIRST of its kind in cement chemicals. The molecule of our Vista Catasoft contains cationic (positive) as well as negative charges in the form of anion in balanced proportion to reduce the surface energy force causing cohesion of freshly fractured cement particles due to vanderwall force. Advantages: Increased mill output by 10%-15% at same cement fineness Reduced grinding cost Effective for both Ball mill & VRM. Increased fineness at same power input to enhance performance Increased cement flow ability Improved cement strength through all ages Minimal dosage (0.05% to 0.06% by weight of cement) A significant reduction of pack set or silo set due to superior flow ability of dry cement powder. Specification: Form: Liquid Color: Brown to amber Specific Gravity: 1.10 â?? 1.13 Chloride content: Nil PH Value: 7 /-1 It complies ASTM C 465 as processing additive for cements Application of VISTA CATASOFT C - 88: Laboratory mill evaluations of clinker and other additions viz fly ash, granulated BF or steel slag. Gypsum, limestone etc are recommended to determine initial blend proportion, grinding efficiency, mortar flow, pack set index and compressive strength of cements at varying dosage to work out the most economic dose level. Cement mill trials should follow to finalize continuous use of this additive. Dosing equipment: VISTA CATASOFT C - 88 should be accurately proportioned through a calibrated dosing system at the first compartment of the mill whether open or closed circuit. Vistaâ??s technical service wing is ready to assist the customer Addition rates: Typical dosage rate may vary from 0.05% - 0.06% by weight of cements including Portland, Portland â?? pozzolana or Portland â?? slag cements as the case may be. Storage: Protect from freezing during cold climate. Once frozen it should be thawed out slowly and remixed thoroughly prior to use. Packing: Available in 250 Kg. Pack & 1000 Kg HDPE container. Shelf Life: Best before 1 year in packed condition.
