APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
Powerful lubricating cum penetrating agent with binding property for Linen and polyester yarns for direct warp and sectional warp. The primary purpose of the product is to increase the abrasion resistance of sized warp yarn. Wax and tallow base softeners and lubricants are hydrophobic in nature. Angelube-CE100 contains 100% hydrophilic heads. Its provides penetrating power and also cold water soluble. Its easy biodegradable and not affect the binding property of the size mix. When use tallow and wax in storage it wont spread out evenly in size mix. It causes formation of uneven film property in yarn. This is the main reason for the weaving efficiency fluctuation. Not like that Angelube-CE100 has fully emulsifying property and its act as excellent leveling agent. It provides even film property to whole size mix. It directly reduce warp breakages and improve productivity in fabric formation.
We are prominent processors and exporters of a wide range of dextrin including Tapioca White Dextrin that protects the fiber by forming a thin coating and also provides stiffness to some of the varieties of interlining fabrics. It is highly appreciated as an efficient thickening agent for textile printing purposes. It is made from eco-friendly raw materials and used as a carrier in color as well as dyestuff industries.
We are prominent processors and exporters of a wide range of dextrin including Tapioca White Dextrin that protects the fiber by forming a thin coating and also provides stiffness to some of the varieties of interlining fabrics. It is highly appreciated as an efficient thickening agent for textile printing purposes. It is made from eco-friendly raw materials and used as a carrier in color as well as dyestuff industries.
We are prominent processors and exporters of a wide range of dextrin including Tapioca White Dextrin that protects the fiber by forming a thin coating and also provides stiffness to some of the varieties of interlining fabrics. It is highly appreciated as an efficient thickening agent for textile printing purposes. It is made from eco-friendly raw materials and used as a carrier in color as well as dyestuff industries.
We are prominent processors and exporters of a wide range of dextrin including Tapioca White Dextrin that protects the fiber by forming a thin coating and also provides stiffness to some of the varieties of interlining fabrics. It is highly appreciated as an efficient thickening agent for textile printing purposes. It is made from eco-friendly raw materials and used as a carrier in color as well as dyestuff industries.
StaThick-MS-CWS-E1414 is a modified, Vegan, Gluten-Free, Plantbased, Non-GMO, Cold Water Soluble starch used as a Emulsifier, Binder, Stabilizer and Thickener in Instant food products and various mayonnaise, sauces and gravies. This product has good resistance to heat and shear. It's stable to conservation and resistant to freezing. The special property of StaThick-MS-CWS-E1414 starch is its large water binding and fat binding Capacities.
Acetylated starch, E1420 in the E number scheme of food additives, is a modified starch. These are not absorbed intact by the gut, but are significantly hydrolysed by intestinal enzymes and then fermented by intestinal microbiota. E number: E1420 (additional chemicals) CAS Number: 9045-28-7 EC Number: 618-556-3
Acetylated Distarch Glycerol is prepared by treating starch with acetic acid anhydride and glycerol. This results in a starch that is resistant against stirring and high temperatures and with a high stability after cooling. They are prepared by physically, enzymatically, or chemically treating native starch, thereby changing the properties of the starch. Modified starches are used in practically all starch applications, such as in food products as a thickening agent, stabilizer or emulsifier; in pharmaceuticals as a disintegrant; as binder in coated paper.
Malto Dextrin is widely used for baking cookies, muffins and other bakery products. It enhances the tenderness and texture. It makes the product soft and lowers the fat content. The Malto Dextrin we supply prevents the formation of crystals on the surface of frozen foods and is used as a sugar substrate in sports drinks. Depending on the depolymerization degree it may be either form-building or leavening agent. It is also easy to digest. TEXTURE & FEATURE: White to cream color fine fluffy powder, free from rancidity and foreign matter. APPLICATION: MALTO DEXTRIN enhances texture and tenderness in cookies, cakes, muffins, and other bakery products. Malto dextrin helps to make soft, low-fat bakery products. Also reduced-fat baked goods. It also prevents the formation of crystals on the surface of frozen foods and is used as a sugar substrate in sports drinks. Depending on the depolymerization degree it may be either form-building or leavening agent. It's easily digested.