Expanded Metal Mesh Expanded Metal Wire Mesh Rigidity Expanded Metal Mesh Expanded metal mesh is an intermediate raw material that allows light and air to flow freely through it and that has more rigidity than the sheet from which it was produced. Introduction of Expanded Metal Mesh Expanded metal mesh is an intermediate raw material that allows light and air to flow freely through it and that has more rigidity than the sheet from which it was produced. It is formed in an expanded metal mesh press and produced from any malleable metal sheet product. The plate, sheet, or coil is simultaneously slit and stretched into diamond-shaped openings. These openings are of uniform size and regularity. Expanded Metal Mesh Basic Types inch inch inch 1 inch Material Suitable for Expanding Carbon Steel, Aluminum, Stainless Steel, Galvanized, Copper, Brass, Titanium, Platinum, Zinc, Nickel, Silver, Gold Surface Finishes hot-dip, galvanizing, pre-galvanizing, anodizing, enameling, power coating, painting, plastic coating, etc Benefits The Flow of Light and Air Design Customization Design Flexibility Strength and Formability Applications Ceilings and roofs, Decorative dividers, Guards, Air and fluid filters, Fencing, Battery cells, Strainers, Partitions, Outdoor furniture, Speaker grills, Security walls, ceilings, floors, doors, Machine and window guards, Shelving and racks, Containers, Greenhouse benches Styles of Expanded Metal Mesh Regular (standard or raised) all expanded metal mesh is produced in regular form off the expanders. The strands and bonds are set at a uniform angle to the plane of the sheet. This gives added strength and rigidity, as well as a skid resistant surface. Flattened is manufactured by processing regular expanded metal mesh in a rolling mill. The rolling process reduces the thickness of the original base metal. Design Designations Strands The sides of the expanded metal meshdesign v Strand Thickness Thickness of the base material from which the sheet was produced. Strand Width Amount of metal fed under dies to produce one strand v Strand Thickness and Width Can be varied to create different openings. The width of the strand should equal or exceed the thickness of the base metal. SWD Nominal dimension, Short Way of Diamond v LWD Nominal dimension, Long Way of Diamond v Design Size Actual dimension SWD and LWD. Measured from a point to a corresponding point on the adjacent diamond. v SWO Short Way of Opening v LWO Long Way of Opening v Bond Where two strands intersect Applications Air and fluid filters EMI/RFI shielding Battery cells Ventilation systems Strainers Satellite and radar antennas Partitions Outdoor furniture Speaker grills Security walls, ceilings, floors, doors Machine and window guards Fencing
Description Introduction of Expanded Metal Mesh Expanded metal mesh is an intermediate raw material that allows light and air to flow freely through it and that has more rigidity than the sheet from which it was produced. It is formed in an expanded metal mesh press and produced from any malleable metal sheet product. The plate, sheet, or coil is simultaneously slit and stretched into diamond-shaped openings. These openings are of uniform size and regularity. Expanded Metal Mesh Material Suitable for Ex pandingCarbon Steel, Aluminum, Stainless Steel, Galvanized, Copper, Brass, Titanium, Platinum, Zinc, Nickel, Silver, Gold Surface Finisheshot-dip, galvanizing, pre-galvanizing, anodizing, enameling, power coating, painting, plastic coating, etc BenefitsThe "Flow" of Light and Air Design Customization Design Flexibility Strength and Formability ApplicationsCeilings and roofs, Decorative dividers, Guards, Air and fluid filters, Fencing, Battery cells, Strainers, Partitions, Outdoor furniture, Speaker grills, Security walls, ceilings, floors, doors, Machine and window guards, Shelving and racks, Containers, Greenhouse benches Styles of Expanded Metal Mesh Regular (standard or raised) - all expanded metal mesh is produced in regular form off the expanders. The strands and bonds are set at a uniform angle to the plane of the sheet. This gives added strength and rigidity, as well as a skid resistant surface. Flattened - is manufactured by processing regular expanded metal mesh in a rolling mill. The rolling process reduces the thickness of the original base metal. Design Designations Strands - The sides of the expanded metal meshdesign v Strand Thickness - Thickness of the base material from which the sheet was produced. Strand Width -Amount of metal fed under dies to produce one strand v Strand Thickness and Width - Can be varied to create different openings. The width of the strand should equal or exceed the thickness of the base metal. SWD - Nominal dimension, Short Way of Diamond v LWD - Nominal dimension, Long Way of Diamond v Design Size - Actual dimension SWD and LWD. Measured from a point to a corresponding point on the adjacent diamond. v SWO - Short Way of Opening v LWO - Long Way of Opening v Bond - Where two strands intersect Price Delivery Port : Tianjin Packaging & Delivery Delivery Lead Time : 15 days
Pictures of API 6A RX24 ring joint gasket: Parameters of API 6A RX24 ring joint gasket:Item No: API 6b flanges RX gasketsSize: 105.9782.1525.46.45Net weight: 0.62KGShape: Octagonal Ring GasketTemperature: -150°C--800°CCertificate: API6A, ISO9001:2000, TS SafetyPressure: 700 barStandard: ASME B16.20 HG20612 HG20633Application: Pipe flanges and valve bonnets high pressure steam, gas, hot oil, oil gas, sol-ventvanor, oxygen at high temperature in oil re-fineries, petrochemical plants, thermal power plants and steam turbined vessels.Warranty:1 year Features of API 6b flanges rx gaskets:1)Octagonal ring gasket is a kind of oil, water, steam, acid and alkali salt, hydrogen, nitrogen and other pipe flanges, valves, pressure vessels, submarine, high-speed joint surface, high temperature and high pressure valve cover and other pressure joint seal. 2)There are a variety of materials and types to suit different design and operating requirements, in full compliance with ANSI B16.20 regulations. Commonly used soft iron, 10 # steel, stainless steel oval and octagonal type, in the new flat-bottomed slotted flange can be used interchangeably, the company can supply within the shortest period. 3)Metal material: 304,304L,316,316L,321,310,340,347,H32750,Carbon Steel, Hastelloy B2,Titanium and so on. 4)Suitable medium: steam, hydrogen, water, natural gas, pyrolysis gas, oil, acid, alkali, salt solution. Application scope: In the petrochemical, petroleum, chemical, fertilizer, polysilicon, high temperature, high pressure, high corrosion, groove valve, flange, container and other interfaces sealed. 5)Note: The choice of metal ring material hardness should be lower than the flange 15 ~ 20 HB, and the old product is not recommended for repeated use, due to material may occur hardening and damage to the flange or sealing performance.6)Certification: ISO9001; CE; TS; API Pictures of our company: RFQ:1.If your company can accept sample order?Yes, we can accept sample for clients test quality before place order.2.Your main market?We sell the goods all over the world and main market including USA, North America, Italy, Mainland and so on.
We have our own factory and we can customize any types of laser machine according to your requirements Description Fiber laser making machine is one of the most advanced laser marking equipment in the world nowadays, because the features of stable output power, great optical model, excellent quality of laser beam, fast working speed and best marking effect and efficiency. Also, it is easy to operate, has no wearing parts, low power, consumption, more incomparable advantages like:better and thinner marking lines, capable of being applied into ore advanced industries needing higher demand of depth, smoothness and precision, in order to perfectly meet requirements of consecutive working in industries. Our laser marking machine adopts the best quality fiber laser source in the world. We have 10w, 20w, 30w, 50w,70w and 100w for optional. The estimated life for laser source will be around 100,000hours, which is 10 times longer life than diode laser and 2 times longer life than other fiber laser source. Applicable Material Fiber laser marking machine can be used for marking logo, serial number, bar code and other beautiful photo on any metallic materials such as stainless steel, titanium, brass, gold, silver, aluminum and lots of engineering plastic products such as mobile cover & charger, consume electronics housing, and etc. Pre-Sales Service *Free pre-sales consulting / Free sample marking/testing *Any kind of technical support are available for users. *We offer progressing solution design to all the distributor and users. After-Sales Service *3 years warranty (People damaged are charged). * Full technical support\ by e-mail, call and video * Lifelong maintenance and spare parts supply. * Free design of fixtures as customers required. * Free training installation and operation for the staffs. 1.What is your payment term? We can agree T/T,L/C,Western union and other etc. 2.Where did you export? In the past few years, our products have been sold to the United States, Europe, Southeast Asia, Australia, the Middle East and other countries and regions. 3. What services do you supply? Quality Guarantee We arrange final test before shipment.. After making sure machine is the best performance, then ship out the machine. Operating guide Explain the use of machines and software. Guide the customer proper use, extend product life and reduce energy consumption. Warranty The whole set of machine warranty period is 1 year. (People damaged are charged) 4.How long do you finish 1 set Only 1-7days
We have our own factory and we can customize any types of laser machine according to your requirements Fiber laser making machine is one of the most advanced laser marking equipment in the world nowadays, because the features of stable output power, great optical model, excellent quality of laser beam, fast working speed and best marking effect and efficiency. Also, it is easy to operate, has no wearing parts, low power, consumption, more incomparable advantages like:better and thinner marking lines, capable of being applied into ore advanced industries needing higher demand of depth, smoothness and precision, in order to perfectly meet requirements of consecutive working in industries. Our laser marking machine adopts the best quality fiber laser source in the world. We have 10w, 20w, 30w, 50w,70w and 100w for optional. The estimated life for laser source will be around 100,000hours, which is 10 times longer life than diode laser and 2 times longer life than other fiber laser source. If you need to mark color on stainless steel, the MOPA laser source could be choosed. we adopt JPT mopa laser source which has good quality and longlife service. Features: 1. enclosed machine, to protect person from laser injure. 2. automatic door. 3. auto lifting, press button to adjust height. 4. inner red light Galvanometer, auto focus. 5. use for marking and engraving on metal and nonmetal. Applicable Material Fiber laser marking machine can be used for marking logo, serial number, bar code and other beautiful photo on any metallic materials such as stainless steel, titanium, brass, gold, silver, aluminum and lots of engineering plastic products such as mobile cover & charger, consume electronics housing, and etc. Pre-Sales Service 1.Free pre-sales consulting / Free sample marking/testing 2.Any kind of technical support are available for users. 3.We offer progressing solution design to all the distributor and users. After-Sales Service 1. 3 years warranty (People damaged are charged). 2. Full technical support\ by e-mail, call and video 3. Lifelong maintenance and spare parts supply. 4. Free design of fixtures as customers required. 5. Free training installation and operation for the staffs. Package: non-fumigation Plywood case Transportation Mode:Shipping/Air/DHL/TNT(According to your requirements) Delivery Time: 1-7days after receive the payment.
As a well-known 1000w laser cutting machine manufacturer, Hanâ??s Yueming Laser produces laser cutting machine, laser marking machine, laser engraving machine, applied materials including carbon steel, stainless steel, silicon steel, aluminum alloy, titanium alloys, galvanized sheet, aluminum zinc, copper and other metal materials widely used in sheet metal processing, aerospace, electronic appliances, metro parts, automobiles, food machinery, textile machinery, engineering machinery, precision fittings, ships, metallurgy equipment, elevators, household appliances, craft gifts, tools processing, decoration, advertising, metal processing, kitchenware processing and other manufacturing industries. Features of Hans Yueming 1000w laser cutting machine CMA1530C-GH-D 1. Gantry rack & pinion and double serve system, MHMD with great torque, maximum acceleration up to 1.2G to ensure the machine could work efficiently and precisely. 2. Intensive chassis with high rigidity. Processed by large gantry milling machine through tempering and vibration aging, non-stress limiting the shape variables and stress relief of the machine within ±0.02mm. 3. High-performance fiber laser generator, ensuring the high-quality-outcome of sheet steel processing. 4. Finite element analysis of gantry help to achieve the best critical state of dynamic performance, light weight, rigid structure. 5. Professional steel plate cutting software, optimizing the layout of cutting pattern to save cutting path and fillet, achieving high speed punching and cutting. 6. The power consummation only 3~4Kw/h (fiber laser generator), just with compressed air the CMA1530C-GH-D could achieve great section on cutting sheet metal. Customer service of 1000w laser cutting machine: pre-sale and after-sale 1, (pre-sale) professional advice on technical problems; 2, Global service Network; 3, 100 service vehicles nationwide; 4, Make after-sale calls to the customer; 5, General Manager Complaint Hotline 6. Free lectures on machine application; 7, Free training (after-sale) 8. Hotline open for 16 hours a day. Han Yueming Laser is a professional 1000w laser cutting machine manufacturer and has won 149 patents, with 7 product ranges, 80 product clusters covering 8 industries, and more than 30 solutions to machine application problems. We offer most thoughtful service and best 1000w laser cutting machine. -
1. Efficient heat transfer Gasketed plate-and-frame heat exchangers (GPHEs) provide efficient heat transfer in compact equipment with a small footprint - much smaller and more efficient than shell-and-tube heat exchangers. Plate heat exchangers are designed to optimize heat transfer, because the corrugated plates provide by far the greatest surface area through which the heat can be drawn from one gas or liquid to the other.The units also have a flexible design and are easy to service and maintain. 2. Types of gasketed plate heat exchangers Industrial -extremely versatile range of heat exchangers for use in all types of industries Industrial semi-welded -used in refrigeration when gaskets are not suitable for one of the media and when higher design pressures are needed WideGap -used for applications involving fibrous liquids, highly viscous fluids, and fluids containing coarse particles evaporators-tailor-made, rising film plate surface evaporator condensers -a compact, plate surface vacuum condenser Material available for 0.5 & 0.6mm 304SS, 316SS, Titanium, ASMO254, Hastelloy C-276, Nickel Ni201, 904L More details please contact us directly . 3. Packing&Delivery Package details: standard export plywood case & carton & customizing according to your requirements. Delivery time: within 10 working days after received the deposit and confirmed all details. 4. Our Advantages: a. Competent in suppling various types plate heat exchangers, and also make plate mould according to customer requirements. b. High quality products, best services and competitive prices. c. Large stock: We keep some regular models pares in stock, so fast delivery. d. Technical service: technical consultation, equipment update, capacity expansion scheme, maintenance and cleaning of the equipment. e. ISO9001&ISO14001: 2008 international quality&environment management standard certification f. Strict quality control systems, PHE: pressure testing; plates: size measuring, quality checking; gaskets:thickness/length/width measuring. 5. Applicationï¼? They are widely used in duties for heating, cooling, heat recovery, evaporation and condensation in industries ranging from HVAC, refrigeration, engine cooling, dairy and food to heavier processes like chemical processing, oil production and power generation.
Carbon Black: Carbon black is a fine, black powder made by burning hydrocarbons in insufficient air. It's primarily used as a pigment and reinforcing agent in various industrial applications. N550: The :N550" designation refers to a particular grade of carbon black, characterized by its specific physical properties and intended applications. It is produced by companies such as Continental Carbon and is used in various industrial products. **2. Physical Properties: Structure: Carbon Black N550 has a relatively high structure and surface area compared to some other grades. It typically has a surface area in the range of 40-60 m/g. Particle Size: N550 carbon black particles are of medium size, providing a balance between reinforcement and coloring properties. Color: It provides a deep black color. **3. Applications: Rubber Industry: N550 is widely used as a reinforcing agent in tires and other rubber products. It enhances the strength, durability, and wear resistance of rubber compounds. It is particularly valued for its ability to improve the performance of high-performance tires. Plastics Industry: It is used in plastics to provide color and enhance properties like strength and UV resistance. Coatings and Inks: N550 is also used in coatings and inks to achieve a deep black color and improve the durability and performance of these products. **4. Performance Characteristics: Reinforcement: N550 offers good reinforcement properties, improving the tensile strength and abrasion resistance of rubber products. Dispersion: It has good dispersion characteristics, which helps in achieving uniform properties in rubber and plastic formulations. Coloring: Provides a rich, deep black color, which is useful for achieving desired aesthetics and performance in various applications. **5. Manufacturing Process: Production: Carbon Black N550 is produced through the incomplete combustion of hydrocarbons in a controlled furnace process. The specific conditions of the manufacturing process control the physical properties of the final product. **6. Regulatory and Safety Information: Safety: As with other types of carbon black, N550 should be handled with care to avoid inhalation or prolonged skin contact. Safety data sheets (SDS) should be consulted for specific handling and safety instructions. **7. Comparison with Other Grades: Compared to Other Grades: N550 falls between the lower structure and higher structure grades of carbon black. It is more reinforcing than lower structure grades (like N660) but less so than higher structure grades (like N330). It offers a good balance of reinforcement and color properties.
Description Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment. Recommended Use :- It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion. Physical Data :- COLOUR :- Yellow FINISH :- Matt SOLIDS BY VOLUME :- 40 �± 3% THEORETICAL SPREADING RATE :- 13.33 sq.mt / lit at recommended DFT of 30 �µ FLASH POINT :- Base : Above 23�° C Hardener : Above 30�° C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) :- SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE :- BASE : 6months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation. Application Data MIXING RATIO :- Base : Hardener (As per our recommendation) APPLICATION :- By Brush / By Conventional Spray THINNER :- Type 290 POT LIFE :- 3 hours min at 30�° C RECOMMENDED DFT :- 30-40 �µ. OVERCOATING INTERVAL :- MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) COMPATIBILITY :- Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Strain the paint through Nylon filter cloth of 200 mesh size and apply uniformly over the surface. All equipments used for above should be properly clean. Application :- By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner and ensuring the uniform application. Use quality brushes for paint application. For Conventional Spray application :- Thinner : Type 290 Addition : 10-15% Nozzle Orifice : 1.2 -1.4 mm Nozzle Pressure : 40-70 p.s.i. For Airless Spray application :- Thinner : Type 290 Addition : Max 5% Nozzle Orifice : 0.28- 0.37 mm Nozzle Pressure : 1400-1800 p.s.i.
Description Two component Epoxy based anticorrosive primer containing red oxide and zinc phosphate as corrosion inhibiting pigments Recommended Use :- This product is recommended as a primer on suitably cleaned mild steel surface in various fertilizer units, refineries, chemical and other plants, transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. The product is recommended as a primer for mild to moderate corrosion conditions. Not to be recommended for immersed water condition. Physical Data :- COLOUR : Red FINISH : Matt SOLIDS BY VOLUME : 40 ± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt. / ltr. at DFT of 30 �µ FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C DRYING CHARACTERISTICS (At 300 C & 65% Relative Humidity) : HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray THINNER : Epoxy Thinner 190 POT LIFE : 4 hours min at 30C RECOMMENDED DFT : 30 - 40 OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated Rubber and Synthetic Enamel Finish Paints. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix, gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application. Add Epoxy Thinner Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly clean. For Conventional Spray application :- Thinner : Epoxy Thinner 190 Addition : 10-15% Nozzle Orifice : 1.2 -1.4 mm Nozzle Pressure : 40-70 p.s.i. For Airless Spray application :- Thinner : Epoxy Thinner 190 Addition : Max 5% if required Nozzle Orifice : 0.37- 0.42mm Nozzle Pressure : 1400-1800 p.s.i.
Plastic products exist in all aspects of our lives, ranging from small plastic playground equipment to small plastic bags, the emergence of plastic will undoubtedly make our lives more colorful! But it is undeniable that waste plastic also brings a lot of trouble to our life. DoingGroup has developed a waste plastic cracking equipment, the use of high-temperature pyrolysis principle, the waste plastics cracked into fuel, carbon black, combustible gas process. DoingGroup's waste plastic cracking equipment workflow is as follows: 1. Use mechanical waste tires to enter the reactor and close the inlet to prevent gas flow out. 2. Carbon, wood or fuel heating reactor, the reactor is generally 200-300 degrees is the beginning of the cracking reaction, when the waste tires vaporized into oil vapor. 3. The hydrocarbons entering the condensing system are liquefied into oil and collected in the tank unit. Our system has a negative pressure device, he can greatly enhance the production of pyrolys is oil. 4, liquefied petroleum gas that can not be liquefied under atmospheric pressure is returned to the reactor as fuel for combustion, which is not only energy saving and environmental protection. 5. After the completion of oil production, the reactor will be cooled. When the temperature drops to 40 degrees, the carbon black and wires will be removed automatically or manually. Nearly RMB ten thousand yuan of revenue can be gained from running one of our equipment in a day, mainly from pyrolysis fuel and carbon black. They have the wide range use in dailylife: Fuel: Mainly used in steel plants, boiler heating, heavy oil generators, cement plants. Carbon black: mainly used for pressure ball burning, refining flour. Which refined flour and can be used for new tires, rubber soles, pigments of raw materials. DoingGroup's fee plastic cracking equipment is so popular, high oil yield, high yield is one reason, but also because of the following advantages of the device: 1. Reactor is produced according to the pressure vessel production standards, using 16mm thick boiler special steel and arc pressure head, can withstand high temperature and pressure. 2. High standard 3-step welding process, not easy to crack, long service life. 3. Pinion rotation device, small power, does not directly contact the reactor, heat transfer less easily deformed. 4. The tertiary cooling system uses a tube condenser, which is the most commonly used and best performing condenser in the oil industry. Make sure that the fuel vapor is sufficiently cool and produces high amounts of oil. 5. Safety devices have oil-water separator, water seal, vacuum device. To ensure safe and stable operation of equipment. Contact: Ms Bonnie Phone: +86-371-5677 1821 Mobile/Wechat/Whatsapp:0086-135-2669-2320 Skype: bonniezhao2 Email: oilmachine@doinggroup.com http://www.recyclingpyrolysisplant.com http://www.doinggroup.com
Catalog No. 9Ti.413.02008 To 9Ti.413.82514 Material Titanium Dia 8.0mm, 9.0mm, 10.0mm, 11.0mm, 12.0mm, 13.0mm, 14.0mm Degree 0�°, 4�°, 8�° Size Size Item Code (0�° 20MM) 0�° 20MM, Dia â?? 08 MM 9Ti.413.02008 0�° 20MM, Dia â?? 09 MM 9Ti.413.02009 0�° 20MM, Dia â?? 10 MM 9Ti.413.02010 0�° 20MM, Dia â?? 11 MM 9Ti.413.02011 0�° 20MM, Dia â?? 12 MM 9Ti.413.02012 0�° 20MM, Dia â?? 13 MM 9Ti.413.02013 0�° 20MM, Dia â?? 14 MM 9Ti.413.02014 (4�° 20MM) 4�° 20MM, Dia â?? 08 MM 9Ti.413.42008 4�° 20MM, Dia â?? 09 MM 9Ti.413.42009 4�° 20MM, Dia â?? 10 MM 9Ti.413.42010 4�° 20MM, Dia â?? 11 MM 9Ti.413.42011 4�° 20MM, Dia â?? 12 MM 9Ti.413.42012 4�° 20MM, Dia â?? 13 MM 9Ti.413.42013 4�° 20MM, Dia â?? 14 MM 9Ti.413.42014 (8�° 20MM) 8�° 20MM, Dia â?? 08 MM 9Ti.413.82008 8�° 20MM, Dia â?? 09 MM 9Ti.413.82009 8�° 20MM, Dia â?? 10 MM 9Ti.413.82010 8�° 20MM, Dia â?? 11 MM 9Ti.413.82011 8�° 20MM, Dia â?? 12 MM 9Ti.413.82012 8�° 20MM, Dia â?? 13 MM 9Ti.413.82013 8�° 20MM, Dia â?? 14 MM 9Ti.413.82014 (0�° 25MM) 0�° 25MM, Dia â?? 08 MM 9Ti.413.02508 0�° 25MM, Dia â?? 09 MM 9Ti.413.02509 0�° 25MM, Dia â?? 10 MM 9Ti.413.02510 0�° 25MM, Dia â?? 11 MM 9Ti.413.02511 0�° 25MM, Dia â?? 12 MM 9Ti.413.02512 0�° 25MM, Dia â?? 13 MM 9Ti.413.02513 0�° 25MM, Dia â?? 14 MM 9Ti.413.02514 (4�° 25MM) 4�° 25MM, Dia â?? 08 MM 9Ti.413.42508 4�° 25MM, Dia â?? 09 MM 9Ti.413.42509 4�° 25MM, Dia â?? 10 MM 9Ti.413.42510 4�° 25MM, Dia â?? 11 MM 9Ti.413.42511 4�° 25MM, Dia â?? 12 MM 9Ti.413.42512 4�° 25MM, Dia â?? 13 MM 9Ti.413.42513 4�° 25MM, Dia â?? 14 MM 9Ti.413.42514 (8�° 25MM) 8�° 25MM, Dia â?? 08 MM 9Ti.413.82508 8�° 25MM, Dia â?? 09 MM 9Ti.413.82509 8�° 25MM, Dia â?? 10 MM 9Ti.413.82510 8�° 25MM, Dia â?? 11 MM 9Ti.413.82511 8�° 25MM, Dia â?? 12 MM 9Ti.413.82512 8�° 25MM, Dia â?? 13 MM 9Ti.413.82513 8�° 25MM, Dia â?? 14 MM 9Ti.413.82514
Catalog No. : 9SS.117.20180 To 9SS.117.35300 Material : Stainless Steel 316L,316LVM, Titanium Nail Diameter ; 2.0mm, 2.5mm, 3.0mm, 3.5mm Size : Length Item Code ULNA Dia. 2.0mm 180mm 9SS.117.20180 190mm 9SS.117.20190 200mm 9SS.117.20200 210mm 9SS.117.20210 220mm 9SS.117.20220 230mm 9SS.117.20230 240mm 9SS.117.20240 250mm 9SS.117.20250 260mm 9SS.117.20260 270mm 9SS.117.20270 280mm 9SS.117.20280 290mm 9SS.117.20290 300mm 9SS.117.20300 ULNA Dia. 2.5mm 180mm 9SS.117.25180 190mm 9SS.117.25190 200mm 9SS.117.25200 210mm 9SS.117.25210 220mm 9SS.117.25220 230mm 9SS.117.25230 240mm 9SS.117.25240 250mm 9SS.117.25250 260mm 9SS.117.25260 270mm 9SS.117.25270 280mm 9SS.117.25280 290mm 9SS.117.25290 300mm 9SS.117.25300 ULNA Dia. 3.0mm 180mm 9SS.117.30180 190mm 9SS.117.30190 200mm 9SS.117.30200 210mm 9SS.117.30210 220mm 9SS.117.30220 230mm 9SS.117.30230 240mm 9SS.117.30240 250mm 9SS.117.30250 260mm 9SS.117.30260 270mm 9SS.117.30270 280mm 9SS.117.30280 290mm 9SS.117.30290 300mm 9SS.117.30300 ULNA Dia. 3.5mm 180mm 9SS.117.35180 190mm 9SS.117.35190 200mm 9SS.117.35200 210mm 9SS.117.35210 220mm 9SS.117.35220 230mm 9SS.117.35230 240mm 9SS.117.35240 250mm 9SS.117.35250 260mm 9SS.117.35260 270mm 9SS.117.35270 280mm 9SS.117.35280 290mm 9SS.117.35290 300mm 9SS.117.35300 Radius Dia. 2.0mm 180mm 9SS.117.20180 190mm 9SS.117.20190 200mm 9SS.117.20200 210mm 9SS.117.20210 220mm 9SS.117.20220 230mm 9SS.117.20230 240mm 9SS.117.20240 250mm 9SS.117.20250 260mm 9SS.117.20260 270mm 9SS.117.20270 280mm 9SS.117.20280 290mm 9SS.117.20290 300mm 9SS.117.20300 Radius Dia. 2.5mm 180mm 9SS.117.25180 190mm 9SS.117.25190 200mm 9SS.117.25200 210mm 9SS.117.25210 220mm 9SS.117.25220 230mm 9SS.117.25230 240mm 9SS.117.25240 250mm 9SS.117.25250 260mm 9SS.117.25260 270mm 9SS.117.25270 280mm 9SS.117.25280 290mm 9SS.117.25290 300mm 9SS.117.25300 Radius Dia. 3.0mm 180mm 9SS.117.30180 190mm 9SS.117.30190 200mm 9SS.117.30200 210mm 9SS.117.30210 220mm 9SS.117.30220 230mm 9SS.117.30230 240mm 9SS.117.30240 250mm 9SS.117.30250 260mm 9SS.117.30260 270mm 9SS.117.30270 280mm 9SS.117.30280 290mm 9SS.117.30290 300mm 9SS.117.30300 Radius Dia. 3.5mm 180mm 9SS.117.35180 190mm 9SS.117.35190 200mm 9SS.117.35200 210mm 9SS.117.35210 220mm 9SS.117.35220 230mm 9SS.117.35230 240mm 9SS.117.35240 250mm 9SS.117.35250 260mm 9SS.117.35260 270mm 9SS.117.35270 280mm 9SS.117.35280 290mm 9SS.117.35290 300mm 9SS.117.35300
Catalog No. 9Ti.414.02508 To 9Ti.414.83014 Material Titanium Dia 8.0mm, 9.0mm, 10.0mm, 11.0mm, 12.0mm, 13.0mm, 14.0mm Degree 0�°, 4 o, 8 o, Size Size Item Code (0�° 25MM) 0�° 25MM, Dia â?? 08 MM 9Ti.414.02508 0�° 25MM, Dia â?? 09 MM 9Ti.414.02509 0�° 25MM, Dia â?? 10 MM 9Ti.414.02510 0�° 25MM, Dia â?? 11 MM 9Ti.414.02511 0�° 25MM, Dia â?? 12 MM 9Ti.414.02512 0�° 25MM, Dia â?? 13 MM 9Ti.414.02513 0�° 25MM, Dia â?? 14 MM 9Ti.414.02514 (4�° 25MM) 4�° 25MM, Dia â?? 08 MM 9Ti.414.42508 4�° 25MM, Dia â?? 09 MM 9Ti.414.42509 4�° 25MM, Dia â?? 10 MM 9Ti.414.42510 4�° 25MM, Dia â?? 11 MM 9Ti.414.42511 4�° 25MM, Dia â?? 12 MM 9Ti.414.42512 4�° 25MM, Dia â?? 13 MM 9Ti.414.42513 4�° 25MM, Dia â?? 14 MM 9Ti.414.42514 (8�° 25MM) 8�° 25MM, Dia â?? 08 MM 9Ti.414.82508 8�° 25MM, Dia â?? 09 MM 9Ti.414.82509 8�° 25MM, Dia â?? 10 MM 9Ti.414.82510 8�° 25MM, Dia â?? 11 MM 9Ti.414.82511 8�° 25MM, Dia â?? 12 MM 9Ti.414.82512 8�° 25MM, Dia â?? 13 MM 9Ti.414.82513 8�° 25MM, Dia â?? 14 MM 9Ti.414.82514 (0�° 30MM) 0�° 30MM, Dia â?? 08 MM 9Ti.414.03008 0�° 30MM, Dia â?? 09 MM 9Ti.414.03009 0�° 30MM, Dia â?? 10 MM 9Ti.414.03010 0�° 30MM, Dia â?? 11 MM 9Ti.414.03011 0�° 30MM, Dia â?? 12 MM 9Ti.414.03012 0�° 30MM, Dia â?? 13 MM 9Ti.414.03013 0�° 30MM, Dia â?? 14 MM 9Ti.414.03014 (4�° 30mm) 4�° 30MM, Dia â?? 08 MM 9Ti.414.43008 4�° 30MM, Dia â?? 09 MM 9Ti.414.43009 4�° 30MM, Dia â?? 10 MM 9Ti.414.43010 4�° 30MM, Dia â?? 11 MM 9Ti.414.43011 4�° 30MM, Dia â?? 12 MM 9Ti.414.43012 4�° 30MM, Dia â?? 13 MM 9Ti.414.43013 4�° 30MM, Dia â?? 14 MM 9Ti.414.43014 (8�° 30mm) 8�° 30MM, Dia â?? 08 MM 9Ti.414.83008 8�° 30MM, Dia â?? 09 MM 9Ti.414.83009 8�° 30MM, Dia â?? 10 MM 9Ti.414.83010 8�° 30MM, Dia â?? 11 MM 9Ti.414.83011 8�° 30MM, Dia â?? 12 MM 9Ti.414.83012 8�° 30MM, Dia â?? 13 MM 9Ti.414.83013 8�° 30MM, Dia â?? 14 MM 9Ti.414.83014
What is a spiral wound tube heat exchanger? Spiral wound tube heat exchanger, also known as threaded tube heat exchanger, turbulent heat exchanger, double bellows heat exchanger. It is a new type of shell and tube heat exchanger. Each heat exchange tube is evenly wound in the heat exchanger shell according to a certain rule. According to the different interface structure, it is divided into L type and Y type. According to whether it can be disassembled, it can be divided into detachable type and non-detachable type. Type: Y type,T type,detachable,double tubesheet, cold trap, gas-liquid separation etc. Material:austenitic stainless steel 316L, double-phase stainless steel 2205, 2507, pure titanium, zirconium, Hastelloy alloy, etc. Tube type:Spiral wound tube/parallel tube/U type tube Tube: �¦8ï¼?�¦10ï¼?�¦12, �¦14ï¼?�¦16,�¦19ï¼?�¦25etc. Maximum working pressure:4Mpa Heat exchanger area:0.1-1000 square meters working temperature:-20-300 degree celsius (customizable) Applicable fluids:steam, circulating water, frozen brine, glacial refrigerant, glycol;. installation type:Horizontal/Vertical Function:Heater, cooler, condenser, evaporate, distillation, rectification Application:Distillation reflux system, concentration system, distillation system, waste gas and heat recovery system, traditional Chinese medicine extraction system, instantaneous sterilization at high temperature, CIP cleaning system, civil HVAC system,heating and cooling of process materials Customization:According to the technical requirements of customers, we can accurately customize the winding tube heat exchangers with various spacing. Package:Standard export wooden box,can be packaged according to customer requirements. Advantages: 1.High heat transfer coefficient :Unique wound tube bundle optimizes the flow state of the fluid on both sides 2.Long service life spiral :The elastic tube bundle can effectively absorb stress and vibration, prolong the service life of the heat exchanger 3.Low scaling tendency :Thereâ??s no dead angle in the heat exchanger, and the tube side and shell side can be emptied; the high flow rate design of the shell side can effectively reduce the probability of scaling on the surface of the heat exchange tube 4.small floor space: Compact structure,about 1/5 of the traditional heat exchanger 5.Low operating cost : Under heat conditons ,it can save the steam ;under the condensation conditions,it can improve the recovery rate. � Shandong Qinglei Environmental Technology Co.,Ltd is an equipment manufacturer integrating design, production and assembly. Our products include heat exchangers, heat exchange units, pressure vessels, storage tanks, TCU temperature control systems, reactors, distillation towers, VOCS purification and recovery systems, vacuum frying machine. If you need any of them,please donot hesitate to let me know,I will reply you ASAP.
Product Description High Frequency Welded Stainless Steel Spiral Fin Tube Extruded Wound Finned Tube Aluminum/ Copper Fins Finned Tube Aluminum Fins Heat Exchanger Tube Product Description The spiral fin tube economizer is a newly type heat transfer equipment, consisting of spiral fin tubes to overcome the serious abrasion and short service time.Which consisted of series of spiral finned tubes, the headers of inlet and outlet, bend, frame and other auxiliaries Structure arrangement: in line/staggered arrangement Finned Tube Aluminum Fins Heat Exchanger Tube Features 1. The equipment body can be designed into many modules to ensure the long term and stable running. 2. Compact structure which can enlarge the heat exchanging area in order to add the heat transfer area and less leakage. 3. Improve the heat transfer efficiency. 4. Structure arrangement: In line or staggered arrangement. Finned Tube Aluminum Fins Heat Exchanger Tube Application Aftercoolers, air coolers, air heaters, charge air chillers, condensers, convection heaters, electric heaters, evaporators, fluid coolers, gas coolers, heat pipes, hydrogen coolers, industrial tumble dryers, intercoolers, immersion heaters, oil coolers, radiators, refrigeration, solvent recovery and steam to air heat exchangers. Technical parameters PRODUCT TYPE TUBE MATERIAL FIN MATERIAL TUBE SIZE FIN SIZE Heat Exchanger Finned Tube Extruded Fin Tube All Kind of Material can be applied Aluminum A1100 15.88~50.8 7~11.5FPI Fin Height Max 16mmH L-Foot Fin Tube All Kind of Material can be applied Copper C1100, C1220 12.70~50.8 7~11.5FPI (Wrap On Type) Fin Height Max 16mmH G-Fin Tube (Embedded Type) Aluminum A1100, A1050, A1060 High Frequency Welded Finned Tube A179 Carbon Steel Tube Carbon Steel Tube 12.70~160 1.5~7FPI Stainless Steel Tube Stainless Steel Tube 0.8~3.2mm. Thickness Alloy Steel Material Alloy Steel Material Integral Copper & Copper Alloy High Finned Tube C12200, C11000, C70600 C12200, C11000, C70600 15.88~22.23 5~9FPI Max 12mm. H Oval Finned Tube Carbon Steel Tube Carbon Steel Tube All Size Available 5~15FPI Stainless Steel Tube Stainless Steel Tube Alloy Steel Material Alloy Steel Material Copper & Copper Alloy Tube Copper & Copper Alloy Tube Monometallic Fin Tube Low Fin Tube Carbon Steel, stainless steel, titanium, copper, brass, nickel alloy, etc. -- 9.52~40 12, 16, 19 28 FPI, etc. Turbo-C Tube Turbo-E Tube Corrugated Tube All Kind of Material -- 6.35~40 2~9FPI High Frequency Welded Stainless Steel Spiral Fin Tubes Carbon Steel Spiral Finned Tubes Factory Provided Description of Spiral Finned Tubes: The spiral fin steel pipes currently used are mostly wound, high frequency welded and brazed spiral fin steel pipes. High Frequency Welded Stainless Steel Spiral Fin Tubes Carbon Steel Spiral Finned Tubes Factory Provided
1.Product Application: This metal fiber laser cutting machine suitable for cutting stainless steel, mild steel, carbon steel, alloy steel, spring steel, copper sheet, aluminum, galvanized steel sheet, brass, titanium, and metal pipe and tube. 2.Product details CHANXAN CW-1325J Laser type Fiber laser-Imported Germany IPG or Chinese Raycus Max cutting area 1300*2500mm Cooling type Water cooling Cutting thickness stainless steel:0.2-3mm;carbon steel:0.2-6mm Laser output power 300W/500W/800W/1000W/1500W X/Y axis pisition accuracy 0.03mm Max cutting speed 20m/min Drive system Servo motor XYZ axis drive type Imported servo drive Tranmission imported ball screw Machine demension 3800mm*1850mm*1300mm Machine weight 1700KG 3.Main Features 1) Professional and high speed and precision metal sheet processing. 2) The best of cost performance, it is the first choice for metal sheet high precision cutting. 3) Cutting the stainless steel, zinc be coated aluminum, carbon steel, galvanizes hseet or pipes in high precision. 4) operating convenient and easy, saying materials. 5) Optical fiber transmission flexibility make operation easy and strong and sturdy High tolerance, Maintenance-free, Production and operation costs very low.  6.Packaging & Shipping Package: Standard export wood packing. Single package size: 200X160X150 cm 7.DELIVERY TIME:7-15days 3-20 days after confirming order,detail delivery date should be decided according to production season and order quantity. 8.Our Company Suzhou Chanxan Laser Technology Co.,Ltd. aren't slowing the pace of innovation since establish in the year of 2009 ,we have got twenty more of patents technology, two self-owned brands, And we have reported to the quality-control-department to set up our own quality standards., Our company are equipped with dozens of sets of laser processing system, supply more value-added services for customers. Also supply good condition for research and development, Through everyone do their effort, our company have the modernizations of standard factory which area in 5000 squares, our productions and service have exist in one hundred more countries and regions. 9.Our Service 1. Machine manual and the installation videos will be sent with machine. It is quite easy to install and operate the machine with the help of manual and installation videos. Our machines have been exported to European countries and customers are quite satisfied with it. 2. If you have any after-sales questions, our engineers can support you via online video or team viewer. 3. we can send the engineers to the door with charges(round tickets, accommodation and training fee) 4. Customers can come to our company training center for free training.
â?¢ The factory has ISO 9001 Version 2000. â?¢ Our SLABS MADE from bauxite ore (Primary). CHEMICAL COMPOSITION SHEET 1 - Si Silicon 0.32 Up mix. 0.38 2 - Fe Iron 0.35 Max 3 - Cu COPPER 0.10 Max 4 - Mn Manganese 0.20 Max 5 - Mg Magnesium 0.45 Up Mix. 0.90 6 - Cr Chromium 0.10 Max 7 - Zn Zinc 0.10 Max 8 - Ti Titanium 0.10 Max 9 - Zr Zirconium n/a 10 - V Vanadium n/a 11 - B Boron n/a 12 - Other Each 0.05 Max 13 - Other Total 0.15 Max ACC. THE ABOVE ANALYSIS THERE ARE THE FOLLOWING ANALYSIS PARAMETER High Strength All Purposes High speed Si % 0.43 UP TO MIX. 0.53 0.38 UP TO MIX. 0.45 0.32 UP TO MIX. 0.38 Fe % 0.20 UP TO MIX. 0.30 0.14 UP MIX. 0.22 0.14 UP TO MIX. 0.22 Mg % 0.45 UP TO MIX. 0.58 0.45 UP TO MIX. 0.55 0.45 P TO MIX. 0.52 - WE CAN OFFER ACCORDING TO CUSTOMERS REQUEST WITH SPECIAL ORDER. PHYSICAL SPECIFICATIONS:- Diameters (mm.) 127±1 mm. 178 ±mm. 203 ±1 mm. 228 ± 1 mm. 254 ± 1 mm. a) Tolerance + 1 mm B) Max. Length 6 meters, + 10 mm Min. 60 cm c) Curvature 2 mm/meter Our Quality is Tested by : â?? Our modern quality control Laboratory consists of Optical Emission Spectrometer (OES). â?? Our manufacturing operations are producing aluminum billets, slab, etc. are controlled round the clock by experienced Chemists & Q.A. Supervisors. â?? Our manufacturing operations are driven by quality, from the way they operate, to the customer service standards they set and the products they deliver. â?? Each heat is being analyzed prior to its pouring aluminum into the molds to ensure proper chemistry, raw material size and dross content of our final product. All elements are controlled within specified limits and proper records are being maintained. Each heat is being assigned a unique batch no which is also marked every relevant ingot to ensure complete traceability at a later stage. â?? In addition to in-process inspection, a highly experienced and dedicated team ensures complete adherence to the most precise standards. Experts are involved right from choosing the highest quality raw material to application of various techniques to ensure the productâ??s confirmation to the highest quality standards. â?? We focus on quality, timely deliver and services which make us to win new opportunities in an increasingly competitive global marketplace. â?? We identify areas for improvement within our quality checks at every stage of manufacturing process to provide our customers with the best value possible in the products which we produce in our modern Plant. Proudly Made in Egypt. â?? PAYMENT TERMS: L/C Irrevocable, confirmed, transferable, divisible, 100% at sight, FFDLC ( fully funded documentary letter of credit). DELIVERY TERMS:- CIF, FOB, &OR C&F. Please feel free to send us your LETTER of material REQUEST for more data please visit us unitedcoinc dot com
Our SLABS MADE from bauxite ore (Primary). CHEMICAL COMPOSITION SHEET 99.8% 99.7% 99.6% 99.5% 1- Si Silicon 0.15 0.20 0.25 0.25 2- Fe Iron 0.15 0.25 0.35 0.40 3- Cu COPPER 0.03 0.04 0.05 0.05 4- Mn Manganese 0.02 0.03 0.03 0.05 5- Mg Magnesium 0.02 0.03 0.03 0.05 6- Cr Chromium n/a n/a n/a 0.05 7- Zn Zinc 0.03 0.04 0.05 0.05 8- Ti Titanium 0.03 0.03 0.03 0.03 9- Zr Zirconium n/a n/a n/a n/a 10- V Vanadium 0.05 0.05 0.05 0.05 11- B Boron n/a n/a n/a n/a 12- Other Each 0.02 0.03 0.03 0.03 13- Other Total n/a n/a n/a n/a â?? - We can supply also Slabs with different alloys:- According the production blew table descriptions:- Or according customer required with special purchase order. PHYSICAL SPECIFICATIONS :- Classification & Sizes Small Size (m.m) Large Size (m.m) 500 x 1100 540 x 1060 500 x 1600 500 x 1750 500 x 1250 540 x 1310 500 x 1500 540 x 1550 500 x 1650 610 x 1600 500 x 1350 600 x 1500 450 x 1420 500 x 1180 600 x 2000 600 x 2100 Our Quality is Tested by : â?? Our modern quality control Laboratory consists of Optical Emission Spectrometer (OES). â?? Our manufacturing operations are producing aluminum billets, slab, etc. are controlled round the clock by experienced Chemists & Q.A. Supervisors. â?? Our manufacturing operations are driven by quality, from the way they operate, to the customer service standards they set and the products they deliver. â?? Each heat is being analyzed prior to its pouring aluminum into the moulds to ensure proper chemistry, raw material size and dross content of our final product . All elements are controlled within specified limits and proper records are being maintained. Each heat is being assigned a unique batch no which is also marked every relevant ingot to ensure complete traceability at a later stage. â?? In addition to in-process inspection, a highly experienced and dedicated team ensures complete adherence to the most precise standards. Experts are involved right from choosing the highest quality raw material to application of various techniques to ensure the productâ??s confirmation to the highest quality standards. â?? We focus on quality, timely deliver and services which make us to win new opportunities in an increasingly competitive global marketplace. â?? We identify areas for improvement within our quality checks at every stage of manufacturing process to provide our customers with the best value possible in the products which we produce in our modern Plant. â?? Proudly Made in Egypt. PAYMENT TERMS: L/C Irrevocable, confirmed, transferable, divisible, 100% at sight. F.F.D.L.C (fully funded documentary letter of credit). DELIVERY TERMS: - CIF, FOB, &/OR C&F. Please feel free to send us your LETTER of material REQUEST or visit us unitedcoinc dot com
Expanded Metal Walkway Grating&Floor&Ramps Expanded Metal Wire Mesh Rigidity Expanded Metal Mesh Expanded metal grating products are used for a variety of uses such as walkways, catwalks, screens, fencing, window guards, open trash containers, vent covers and many more applications. Peterson Company carries expanded metal in a variety of materials such as aluminum expanded metal, stainless expanded metal, galvanized expanded metal, carbon steel expanded metal, copper expanded metal, brass expanded metal and titanium expanded metal. Product Details A strong and aesthetic solution for walkways and gantries. The Expanded Metal DONGJIEs heavy duty walkway range is an effective well established product, proven throughout industries where safety underfoot is critical. When lives can depend upon strength and grip, at heights and in hazardous conditions, the Expanded Metal Companys range can be relied upon to satisfy safety requirements. The Expanded Metal walkway range is excellent for slopes and heights due to its anti-slip properties. Mesh allows the free ow of water to give natural drainage. Snow,ice and mud break off underfoot to maintain secure footing. The solid appearance of the walkway range gives an excellent aesthetic appeal for design. Features and Benefits Quality Guaranteed ISO 9001: 2008 Environmental Mana gement ?�Technical support available Wide choice of standard products ?�Available in Stainless Steel, Aluminium& Mild Steel Economical solution for all types of walkway and gantry applications Tested and measured load bearing capacities New Gripwalk for extra anti slip protection Supagrip gives _x001D_firm hold for both wheelchairs and footwear Option to weld or clip the sheets in situ Plasma cutting service for efficient and accurate shaping Superb strength to weight ratio Low maintenance Material Specifications You can choose from a wide range of standard items from gripwalk for extra anti-slip protection or walkway in a range of materials with measured load bearing capacities. Products in the DONGJIEs range give a non-slip, economical solution for all types of walkways, stairtreads and gantries. Aluminium Walkway Ref No. LWD SWD Swdt Stk Kg/m� % Open Area Overall Thickness Standard Manufactured Size 2496 60.96 25.40 5.82 4.70 6.08 52 12.70 2440 x 1830 4895A 121.92 38.10 11.90 6.00 10.16 43 20.60 Mild Steel Walkway Ref No. LWD SWD Swdt Stk Kg/m� % Open Area Overall Thickness Standard Manufactured Size 2496 60.96 25.40 6.10 4.5 17.29 51 12.70 2440 x 1220 4896 121.92 33.87 6.35 4.5 13.23 65 13.50 4897 121.92 33.87 7.90 4.5 16.45 58 15.10 4898 121.92 33.87 9.53 4.5 19.83 50 17.50 4899 121.92 33.85 9.53 6.00 24.98 50 19.80 4894 121.92 38.10 13.06 6.00 32.22 38 22.20 Material Illustrations---A
