Wanted : Construction Equipment Suppliers and Manufacturers

Construction Equipment

* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.

The snow removing equipment is the necessary equipment of snow cleaning for farm,orchard, schools, parks, squares, residential areas, garden, lanes sideways, bridges and other key securing sites and widely used in snow winter. This equipment could improve the efficiency of snow removal, reduce labor intensity, and ensure pepole going out more safety and convenient. 1).The road sweeper can be matched to tractor,wheel loader,forklift, 2).powered by hydraulic output of these machinery,only tractor could be driven by PTO. 3).PP with steel wires brushes. 4).Working width from 1200 to 2500mm 5).Suitable for cleaning road,street,floor and other flat.

*The engine adopts famous brand engine, 100% inspection before delivery. *The Snow Cleaning Machine adopts full metal jacket design,after oxidation spray,anti-corrosion rust proof,long service life. *Double LED lamp of operation panel, greatly improving the workers efficiency and safety at night and early morning. *The Snow Cleaning Machine uses monolithic auger design, low cost of vulnerability consumption and easy replacement. *The Snow Cleaning Machine has the advantages of fashion appearance,mult functions, light and flexibility,simple operation.

Aggregates are mixtures of sand, gravel, crushed rock or other bulk minerals used in construction, principally as a component of concrete, and in civil engineering. At CEMENTATION we supply aggregates for a range of core applications, from fill materials to aggregates that can be used in concrete, precast concrete, asphalt and for surface dressing. Aggregate plays an important role in concrete and construction part. We supply quality material which makes durable concrete with higher compressive strength and low permeability having better finish. We can supply a wide range of coarse, fine and blended aggregates in accordance with international standards. We acquire rock mines and stone crushing plants and enable us to fulfil contract of any size. Progressive stages if crushing and screening enable us to produce a range of aggregate sizes (06mm to 65mm) APPLICATIONS Road and Highway surfaces Constructions or Civil work Railway Ballast To make Concrete or Asphalt Filling

Fuel LPG. Fuel Tank Capacity 2.0 L Fuel Consumption : App. 225 g P/H Length : 350 mm Height : 330 mm Width : 150 mm Weight(kg) Empty : 1.5 Kg (Empty)

Hollow Plastic Concrete Formwork for fundational building Size:1220*2440mm Thickness:15mm/18mm/20mm MOQ:100pcs Advantage:Reusable Application:concrete panels building formwork Color:Grey Weight:31kgs Quick Details: Product Name:Plastic concrete formwork Application:Concrete panels building formwork Material:PP plastic material Surface:Cleanly ,Glossy and smoothy Size: 1220*2440mm Thickness: 15mm, 18mm,20mm Type: Construction formwork Color: Grey Certificate: ISO9001:2008 Weight: 31KGS Packaging & Delivery Selling Units:Single item Single package size: 244X122X2.0 cm Single gross weight:31.0 kg Package Type:carton box packing onto wooden pallet Lead Time : Quantity(Piece)1 - 200201 - 336337 - 810>810 Est. Time(days)5715To be negotiated

The CORI is the product for the direct reduction unit: First, it will be stored in product passivation silos, its transportation by conveyors. After that, it will be stored in the warehouse for further use. Production rate fo312 T/H. Assuming 8,000 hours of annual operation, this equates to in annual production of 2,500,000 tonnes. -IRON: (Rod a Benton):Hot-rolled product in multipurpose steel for high-adherence construction, weldable in RB 500 grade. NA 8634(2015) and ISO 6935-2 (2015). Diameter: A wide range of diameters: 8,10,12, 14, 16,20,25,32,40 mm. Length :12m (-0mm +100mm) with the possibility of making specific lengths of less than 12m according to customer demand for diameters ranging from 8mm to 16mm. 12m to 18m for diameters ranging from 16mm to 40mm. Marking : A specific AQS marking is engraved on the rebar bars for the diameters: 8,10,12,14,16mm And the identifying code AQS-diameter-RB500 for the diameters: 16,20,25,32,40mm - Portland Cement 42.5 (Bags, Bulk) -Wire rod: of round section with a diameter varying between 5.5 mm to 14 mm, of high quality. The round and smooth wire rod is obtained by hot rolling in accordance with the Algerian standard an 8634 and according to international standards.-The Fields Of Use Of Wire Rod Are As Follows:- Drawn Wire-Welded Mesh-Nail, Tie Wire, Galvanized Wire- Gabions- Barbed Wire-Spring Wire- Bolt-Nut-Screw- Paperclips-Pickup Wire-Welding Wire -BILLET: A billet is a section of metal used to roll into bars and shapes. It can be produced with ingots or directly by continuous casting. Billets are used as raw materials or for extrusion, forging, rolling and other metal processing operations.

Building and Construction Material

outdoor park exercise machine fitness accessories outdoor gym equipment Outdoor fitness Equipment Specification: Materials: Used different size galvanized steel pipe, surface painted with powder coating. Screws are made by stainless steel. Installation: DIY and easy for installation. Advantages: 1.High quality standard 2. Anti-static Anti-skid and Anti-crack. 3. Professional designer will design for you freely. 4.Provide high quality products at competitive price, with excellent service. Applicant: Park, Residential area , School, Garden, Amusement park, Community, Commercial center and other public places. Package: standard export package. Cotton inside, PP film outside. The delivery date : 15 to 45 days after payment. Attention: Keep your exercise slowly. The patients must ask the doctors for permission before using it. If feel any sick when training, you should stop immediately and consult with the doctors. The patients and children should be accompanied when using it.

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.