Cylinder Sealing Grease Mfz 2 Suppliers and Manufacturers

Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)

Focus-6100 butyl tapes are mainly made of butyl rubber with excellent performance in waterproofing and sealing. Main Specification (Customized size is acceptable.) 3.0mm thickness * 12mm width *15m roll length 2.5mm thickness * 8mm width * 15m roll length 2 mm thickness * 15mm width * 20m roll length 2.5 mm thickness * 8mm width * 20m roll length Main Color black, grey, white Technical Data Product Series FOCUS-6100 Application Composite Materials Industry Elongation 500% Heat Resistance 90, no flowing within 2h Low Temperature Flexibility 40, no crack on surface within 24h Peel Strength 23N/cm Tensile Strength 220KPa Anti UV non-hardening and no cracks within in 2000h Corrosivity Non-corrosive to galvanizedsheet, aluminum sheet and coppersheet. Advantages Strong adhesion. Wide application temperature range. Excellent performance in waterproofing and sealing. Applications * During the production of vacuum extraction process for wind mill blade, it has excellent sealing property between vacuum bags and molds. During the production of vacuum extraction processfor fiberglass, it has excellent sealing property between vacuum bags and molds. * During the production of vacuum extraction process for cabin cover, it has excellent sealing property between vacuum bags and molds. * As auxiliary materials, our Focus-6100 series are widely used in the production of wind mill blade, fiberglass, cabin cover, car tail bracket, automotive engine cover, yacht. * Our products have excellent sealing property between vacuum bags and mold during the vacuum extraction process.

Commodity: Sodium Lauryl Ether Sulfate Synonyms: Sodium Laury Ethyle Sulfate 70% aqueous solution; Sodium Alkyl Ethoxy Sulfate 70% aqueous solution; Sodium C10-16 Alkyl Ethoxy Sulphate (Predominantly C12-C14) 70% aqueous solution; SLES 70% aqueous solution Molecular formula: CH3-(CH2) n-(O-CH2-CH2) p -OSO3Na, where n=9~15, p=2 Mean molecular weight: 388 Description: It has excellent detergency, emulsification ,and foamability, it is easy to dissolve in water. As well as favorable hard-water resistant and high-biodegradation. Specifications: ITEM SLES - 70 SLES - 28 Appearance Transparent or white viscous paste light yellow transparent liquid Odor No strange odors No strange odors Active Matter% 70�±2 28�±2 PH value 7.0-9.5 7.0-9.5 Unsulfated matter% Max. 2.0 Max. 1.0 Sodium sulfate % Max. 1.0 Max. 0.5 Microbiological(CFU/g) Max. 100 Max. 100 Dioxane(ppm) Max. 50 Max. 50 Heavy metal(ppm) Max. 10 Max. 10 Peroxide% Max. 0.1 Max. 0.1 Color Max. 10 Max. 10 Usage: 1. Used to prepare the shampoo, bath foam, soap,hand cleaner , liquid detergent and detergent. 2. Used in hard surface cleaner, such as the glass cleaner, car cleaner, they always used with the K12ã??LAS-Naã??6501. 3.Used in the textile, paper making, leather, machinery, petroleum. Industry. Packing: plastic drum, per 160kg/170kg/200kg/220kg net weight Loading weight in 1x20fcl: 18.24mt for 160kg drum 19.38mt for 170kg drum 17.6mt for 220kg drum Storage: sealed and stored at the room temperature, the shelf life is two years.

Commodity:Avobenzone CAS No. 70356-09-1 Molecular Formula C20H22O3 Molecular Weigh 310.39 EINEC No. 274-581-6 Specification Quality standard: USP36 Appearance Off-white powder Assay 95.0-105.0% Melting range 81.0~86.0 Impurities Any individual impurity: 3.0% The sum of all of the impurities: 4.5% Loss on drying 0.5% Packaging and storage: 1kg/aluminum foil bag. 25kg/barrel, pharmaceutical packaging barrel. Sealed, stored in dark, with a shelf life of 2 years. Reference dosage: The hygiene standards for cosmetics stipulate that the maximum amount added shall not exceed 5%, and the general dosage is 1-4%. Usage: Sunscreen agent-1789 is the most effective fat soluble UVA filter and is a safe and effective UVA sunscreen approved by the US FDA for sale on the counter. It can effectively block UVA, thereby increasing the SPF value of sunscreen products. It can improve the efficacy of sunscreen products when used in combination with UVB filters, and BL-200 has the best effect when used in combination with octyl methoxycinnamate. BL-200 can increase its stability in the product. It has an extremely effective protective and repairing effect on human skin. Application: This product is soluble in oil and can be formulated into a cream using the usual method. However, the product turns red when it encounters metal ions, so other components such as formula water should not introduce metal ions. The equipment should be made of pure stainless steel, and an appropriate amount of EDTA-2Na should be added to the formula water phase to chelate with metal ions.

Product Name: Ferrous Sulphate Heptahydrate Molecular Formula: FeSO4. 7H2O CAS No.: 7782-63-0 Mol Weight: 278.05 Usage and Dosage: 1. Industrially: ferrous sulphate heptahydrate is mainly used as a precursor to other iron compounds. It is a reducing agent, for the reduction of chromate in cement. 2. Nutritional Supplement: Together with other iron compounds, ferrous sulphate is used to fortify foods and treat iron-deficiency anemia. Constipation is a frequent and uncomfortable side effect associated with the administration of oral supplements. Stool softeners often are prescribed to prevent constipation. 3. Colorant: Ferrous sulphate can also be used to stain concete and some limestones and sandstones a yellowish rust color. 4. Water Treatment: Ferrous sulphate has been applied for the purification of water by flocculation and for phosphate removal in municipal and industrial sewage treatment plants to prevent eutrophication of surface water bodies. Storage: Storage Store in cool, dry, well ventilated area, removed from oxidising agents (eg. hypochlorites), acids, metals and foodstuffs. Ensure containers are adequately labelled, protected from physical damage and sealed when not in use. Large storage areas should have appropriate ventilation systems. Precaution: Flammability Non flammable. No fire or explosion hazard exists. Packing: Net weight 25kgs, 50kgs per each plastic woven bag Technical Specification Appearance: Light green crystalline powder Fe 19.7%min Pb 20 ppm max As2 ppm max Cd 5 ppm max Size Crystalline Powder

EN 590 10ppm CIF PRICE $370/360 TRANSACTION WORKING PROCEDURES CIF DELIVERY 1 Buyer issues Irrevocable Corporate Purchase Order (ICPO). 2. Seller issues SPA to Buyer. Within 48 hours Buyer signs seals and returns the SPA to seller. 3. Seller notarizes the contract, at its own expenses and submits Partial Proof of Product (via email) as follows: A) Refinery Commitment to Supply B) Product Passport C) Certificate of Origin D) Export license E) Proforma invoice for the first month of value f) Statement of Availability of Product h) Company Registration 4. Within 5 banking days, Buyer's bank sends Irrevocable Operative SBLC via MT760 or DLC via MT700 according to seller's fiduciary bank verbiage to seller nominated fiduciary offshore bank account for first month shipment, 5. Seller's Bank issues Full POP Documents to the Buyer's Bank alongside with 2% Performance Bond (PB 2%). 6. All parties finalized the signing of the NCNDA/IMFPA. The buyer will be invited by the seller to witness the loading of the product (At Buyers Cost, Maximum of Five Personals/Representatives, Optional). 7. Seller clears vessels from the commercial's terminal (Loading Port), the buyer confirms shipping documents with ship master while seller effects delivery to buyer destination 8. Upon the arrival of cargo at the discharge port, and after SGS/Q&Q at discharge port buyer's bank release to seller's bank payment by TT/MT103 within 7 (Seven) banking days. Seller release payment to all intermediaries as per signed NCNDA IMFPA within 48 hours.

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.

Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor

High vacuum sealing packaging machine high temperature sterilization food sealing machine is suitable for all kinds of plastic composite film bags or aluminum foil composite film bags. After vacuum packaging, it can effectively keep fresh, guarantee quality, moistureproof, clean and clean all kinds of rice cakes, bean products, meat products, aquatic products, agricultural products, pickles, fast food products, prepared foods, powders, spices, electronics, hardware parts and drugs It can prevent mildew, rust, pollution, oxidation and vacuum sterilization, so as to prolong the shelf life. welcome order ! small type ,big type ,single chamber ,2-chamber ,rolling vacuum sealing packing machine ....!

High food vacuum packaging machine high temperature sterilization food sealing machine is suitable for all kinds of plastic composite film bags or aluminum foil composite film bags. After vacuum packaging, it can effectively keep fresh, guarantee quality, moistureproof, clean and clean all kinds of rice cakes, bean products, meat products, aquatic products, agricultural products, pickles, fast food products, prepared foods, powders, spices, electronics, hardware parts and drugs It can prevent mildew, rust, pollution, oxidation and vacuum sterilization, so as to prolong the shelf life. welcome order ! small type ,big type ,single chamber ,2-chamber ,rolling vacuum sealing packing machine ....!

Cassava can as the raw material for starch ,ethanol /alcohol very useful for people ,low cost high profit ! 1.Cassava starch production line machine small capacity to big capacity design ,manufacture,installation,training for clients. Cassava starch production line process flowing : cassava feeding----first time drying washing (removing impurities)----second time water washing(remove small impurities----cassava crush----sieve off cassava residue ----starch milk purification----dewater drying----screening packaging .Whole process are sealing process no-touch hand keep sanitary ,good quality starch . The starch are wildly use for raw materials such as food ,medical and cosmetics ,textiles,papermaking ,candy, beverages, animal feed, biodegradable materials, adhesives , chemicals, ethanol /alcohol , etc. 2.Cassava ethanol alcohol process machine plant According to client inquired to design /manufacture /installation different cassava process machine with different product .

2-head packaging machine (also can 4-18head according different capacity choice) Packaging speed 15bags/min Bag length 90-320mm Bag width 80-210mm Overall weight 400kg Power 1.8kw/220v Packaging capacity 20-1000ml Outer packaging size 820 x1220 x 2500mm Packaging form Back sealing This machine is an intelligent weighing automatic quantitative packaging machine with four scales and microcomputer control. Suitable for quantitative packaging of granular materials such as miscellaneous grains, nuts ,pesticides, fertilizers, veterinary drugs, premixes, additives, laundry detergent, salt, monosodium glutamate, white sugar, seeds, rice, snacks, hardware, etc. Performance characteristics: 1. High precision digital sensors enable precise measurement to be achieved instantly. 2. The microcomputer control system is technologically advanced, easy to operate, and more reliable to use. 3. Fast and slow vibration feeding, automatic correction of errors, achieving high-precision packaging. 4. Four scales work alternately, with fast packaging speed. 5. High quality stainless steel is used for the material contact part, which is anti-corrosion, dust-proof, and easy to clean. Host configuration: This machine is equipped with a dual CPU microcomputer control system, a 5-inch LCD display in Chinese or English, a user-friendly operation interface, automatic cursor detection and tracking, and simpler operation. Equipped with high-precision stepper motors to ensure the accuracy of the cutting position of each packaging bag.

Glazing glass is a combination of two or more pieces of glass spaced apart with a spacer bar and hermetically sealed with a primary and secondary sealant to form a single unit with one or more air spaces between each other. Max size :3300*12000mm Main character : Energy saving , improving the thermal performance Sound insulated Security and comfort   Component : 1.Ã? Glass items:Ã? consists of hard or soft low E glass ,reflective glass ,clear glass ,tinted glass, with types of flat tempered ,bent ,laminated processing ,according to the application 2.Ã? Spacer bar :is the material used to separate the two glass lites in an IGU. It can be made by aluminum,stainless steel,hybrid ,plastic material . The spacer width usually from 6mm-18mm.