Features: Adopt quality parts ,RF metal CO2 laser tube. NO maintenance laser source. High speed galvo scanner. Easy Operate without route maintenance. Higher precision, faster speed. Specification: Model LP-10/30/50/100 Laser Power 10W/30W/50W/100W Laser Wavelength 10.64um Q-frequency 20KHz~100 KHz Divergence 0.3mard Marking Range 100*100mm/200*200mm/300*300mm Minimum Line Width 0.02mm Minimum Character 0.15mm Marking Depth 0 ~0.5mm Engraving Line Speed �7000mm/s Repeatability Accuracy ±0.001mm Beam Quality M2:1.2~1.8 Marking Format Graphics, Text, Bar Codes, Two-dimensional Code, Automatically Marking the Date, Batch number, Serial number,Frequency,etc. Graphic Format Supported bmp,jpg,gif,tga,png,tif,ai,dxf,dst,plt,etc. Working Voltage 220V±10%/50Hz/4A Applied Materials: Paper, plastics, wood, glass, painted pottery, Non-metallic materials and oxidation plating paint materials on the surface of metal. Applied Industries: Food, beverage, wine, mineral water, pharmaceutical, chemical products, tobacco, plastic & rubber Product accessories, building materials and other manufacturing products or packaging.
General type 40W60W80W MYJG CO2 laser power supply myjg-40/60/80watt laser power source 1. Product Features: It has green color control signal terminal board 1. This laser power supply adopts zero current and half bridge soft switch circuit, it makes the power supply have high efficiency and quick response speed. Thus it is easy to match with CO2 laser tube made by any factories. 2. This laser power supply is easy to be controlled, it is suitable to High or Low level signal. The TTL level can control start or stop of laser output. While the power supply has emergency protection switch which can indicate water through and ventilation. 3. The laser output power can be adjusted by 0-5V analog signal or PWM signal. 4. This laser power supply has open cirsuit protection function. When protective earthing is good, the laser power supply can be in open circuit status during short time. This function can protect power supply when laser tube burst. 2. Aging test: Each laser power supply must pass this test which is taken at 60 degree centigrade for 12 hours in full load status. And the power supply must start and stop at each 7 seconds for 500 times. In this way we can ensure the laser power supply is qulified. 3. Specification: Item MYJG-40 MYJG-60 MYJG-80 MYJG-100 MYJG-130 MYJG-150 30KV 35KV 45KV 50KV 50KV 50KV 20mA 23mA 30mA 30mA 35mA 38mA Input AC Voltage AC220V or AC110V Input DC Voltage DC 300V or DC150V Input AC Frequency 47-440Hz Efficiency 91% Over Current Protection 130% of Max. Current Open Circuit Protection Yes (For short time) Cooling Fan Cooling Voltage Range of High Level Control Not Less Than3V Voltage Range of Low Level Control Not More Than0.8V Working Temperature -30 - +65 Degree Centigrade Humidity 20-85%RH(No Dew) Withstand Voltage Input-Output AC1500V/MinNot More Than10mA Input-Shell AC1500V/MinNot More Than10mA Output-Shell Connected Insulation Not Less Than 50MOHM(DC500V) Leakage Current Not Less Than 1mA(AC220V)Not More Than 0.5 mA(AC110V) Shock Resistance Amplitude: 0.5mm, Frequecy:10-55Hz, 3D Dretion:2 Hours MTBF Not Less Than30,000hours Full Load 60 Degree Centigrade test 12Hours 7 Seconds Start/Stop Test 500 Times Dimension(LXWXH)171mmx161mmx91mm Note Power supply warranty:12 months. Delivery time:2 working days after payment received. Package:Carton,foam and wooden box. Shipping method:DHL,UPS,Fedex or TNT Payment method: T/T,PAYPAL,Western Union Application:General type power supply and widely used on 40W-150W CO2 laser engraving machine.or cutting machine
S&A chiller for cnc router and co2 laser machines S&A brand CW-5200 chiller is fit for cooling cnc router and co2 laser machines. Its cooling capacity up to 1.4KW , ±0.3â?? temperature control precision and temperature control range in 5-35â??. It is popular for its 2 temperature control modes as constant temperature and intelligent temperature control. Multiple alarm functions: compressor time-delay protection, compressor overcurrent protection, water flow alarm and over high / low temperature alarm. S&A chillers have passed ISO, CE,RoHS and REACH approvals and the warranty is 2 years. chiller CW-5200 specfications: Voltage:110V-220V; Frequency: 50/60Hz; Refrigerant: R-22 / R-134a / R-410a Pump power: 0.03KW/0.05KW/0.1KW; Tank capacity:6L Max. lift:10M-25M; Max. flow: 10L/min- 16L/min N.W: 26Kgs; G.W: 29Kgs; Dimension : 58 X 29 X 47 cm (L X W X H); Packing dimension: 70 X 43 X 58 cm (L X W X H) About S&A Brand S&A produces more than 60000 units of industrial chillers by year,we always insist onâ?�Quality Firstâ?� in design and production. â??S&Aâ?� and â??TEYUâ?� have been enjoying high reputation among hundreds of manufacturers which are from both at home and abroad and export rate reaches above 60%.
Copper coated co2 welding wire er70s-6 Standard: er50-6, er70s-6, sg2, g3si1 Size: 0.8mm, 0.9mm, 1.0mm, 1.2mm, 1.6mm Package: plastic spool, metal spool, drum Packing weight: 1kg, 5kg, 15kg, 20kg, 250kg, 350kg Oem service is ok
Textile fabrics co2 laser cutting machine Model no.: 1610 i (with one laser tube and one laser head) And 1610 ii (with two laser tubes and two laser heads ) Power: 130 w Same as above Wooden case
Material of co2 welding wire: co2 gas shielded welding wire is made from excellent ho8mn2sia steel by drawing, Straightening and copper coating. Features and application of co2 welding wire: s table electric arc, low splashing, high deposition efficiency and good Welding seam. Co2 welding wire can be welded automatically or semi-automatically.The co2 welding wires are widely used on low carbon steel and low alloy steel, rolling stock, container, engineering machinery, and pressure container, etc. Carton packing in outer spool.Then packed on pallets
We are one of leading manufacture of coated abrasive and welding products from india . Our company is an interested to do the long term business with you. Our quality products are Coated abrasive belt Coated abrasive roll Coated abrasive snad disc Flap wheel Mob wheel with spindle Water proof sheets Pse disc Velcro disc Cloth disc And welding wire and electrode Welding co-2 ms wire Welding ms electrode e6013 Welding electrode stainless steel Welding electrode hard facing Welding electrode curtly Etc. Depend upon the customer
Our website: alsafegascylinders point COM I'm Shirlybai, just write me to the following address: shirlybai at alsafegascylinders point COM Product Name: Beverage CO2 gas cylinder Manufacturer: Liaoning Alsafe Technology Co., Ltd. Specification: LW-203-13.4-15-H Standard: ISO7866 or DOT 3AL Certificate: CE, TS Third party Inspectors: TUV, CSEI, SGS Filling content: Food grade CO2 Color: Aluminum Outside surface treatment: Transparent painting Thread: 1.125-12UNF Valve: QF-35C Form A, Form E avaliable. Features: ¡¡èMade by aluminum 6061; ¡¡è40% lighter than steel cylinders; ¡¡èNo magnetism; ¡¡èHigh corrosion resist and special inner surface treatment, ensure beverage gas clean and smelless, ideal for food grade CO2 storage; ¡¡èStable performance; ¡¡èWidely used in Beer systems, Carbonated beverage machines, etc.; ¡¡èChoice of worldwide top brands and enterprises. We can also produce other specifications according to your requirement. Quality & Safety 1. We have established the quality guarantee system according to the Requirements for Boiler and Pressure Vessel Manufacturing Licensing of China and obtained the certificate issued by General Administration of Quality Supervision, Inspection and Quarantine of the P.R.C (AQSIQ), qualified to manufacture B1 and B3 grade pressure vessels. 2. Each new type of cylinders has to pass type tests held in qualified laboratories approved by third party inspector (TUV, CSEI for example) before mass production, including bend test, drop test, hydrostatic test, etc. according to relevant standards. 3. Every batch of cylinders (200 pieces as one batch normally) are manufactured and tested under supervision of local special equipment inspection and research institute and then issued batch test report. 4. Each finished cylinder has to pass leakage test before delivery to customers to ensure no leakage occurs. plastic net, carton and pallet
Our website: alsafegascylinders point com I'm shirly bai, you can write me to the following address: shirlybai at alsafegascylinders point com Product name: beverage co2 gas cylinder Manufacturer: liaoning alsafe technology co., ltd. Specification: lw-203-20.0-15-h Standard: iso7866 or dot 3al Certificate: ce, ts Third party inspectors: tuv, csei, sgs Filling content: food grade co2 Color: aluminum Outside surface treatment: transparent painting Thread: 1.125-12unf Valve: qf-35c Form a, form e avaliable. Features: ¡¡èmade by aluminum 6061; ¡¡è40% lighter than steel cylinders; ¡¡èno magnetism; ¡¡èhigh corrosion resist and special inner surface treatment, ensure beverage gas clean and smelless, ideal for food grade co2 storage; ¡¡èstable performance; ¡¡èwidely used in beer systems, carbonated beverage machines, etc.; ¡¡èchoice of worldwide top brands and enterprises. We can also produce other specifications according to your requirement. Quality & safety 1. We have established the quality guarantee system according to the requirements for boiler and pressure vessel manufacturing licensing of china and obtained the certificate issued by general administration of quality supervision, inspection and quarantine of the p.R.C (aqsiq), qualified to manufacture b1 and b3 grade pressure vessels. 2. Each new type of cylinders has to pass type tests held in qualified laboratories approved by third party inspector (tuv, csei for example) before mass production, including bend test, drop test, hydrostatic test, etc. According to relevant standards. 3. Every batch of cylinders (200 pieces as one batch normally) are manufactured and tested under supervision of local special equipment inspection and research institute and then issued batch test report. 4. Each finished cylinder has to pass leakage test before delivery to customers to ensure no leakage occurs. Plastic net, carton and pallet
Aquarium co2 aluminum high pressure cylinders 20 pcs in one carton
Dot/tc approved Tped pi approved 25 pcs in one carton
Weldings solder CO2 gas shielded welding wire ER50-6 submerged-arc welding wire H08A, ER05-6 AWS ER70S-6 CO2 gas shielded welding wire Types: flux-cored wire and solid wire Diameter: 0.8mm-1.6mm Melting Point: Normal Weight: 5~20kg/spool;250~350kg/drum Application: welding Flux Content: standard Packaging Detail:15kgs/roll/carton, 72cartons/pallet, 21-24metric tons/20ft container Usages: CO2 gas shielded welding wire Almost used in welding of the carbon steel and the low alloy steel. And welding material is the combination of filler and fluxes. ER50-6 welding wire 16.mm 1.Diameters: 0.8mm,1.0mm,1.2mm,1.6mm 2.Weight: 5kg,10kg,15kg/spool 3.Packing: 15kgs/roll/carton, 72cartons/pallet, 21-24metric tons/20ft container 4.Types: flux-cored wire and solid wire ER50-6(AWS A5.18 ER70S-6) meet China standard, main chemical composite(%): c0.06-0.15¡¢mn1.40-1.85¡¢si0.80-1.15¡¢p¡Ü0.025¡¢s¡Ü0.035¡¢cu¡Ü0.50. Usages: CO2 gas shielded welding wire Almost used in welding of the carbon steel and the low alloy steel. And welding material is the combination of filler and fluxes. Co2 welding wire AWS ER70S-6, 1.2mm Material: Cooper plating Wire Size: 0.8mm 1.0mm 1.2mm 1.6mm HO8Mn2SiA Ho8Mn2Si Ho8Mn2SiMoa Spool Size: D100mm, D200mm,D270mm,D300mm,K300mm Melting Point 500(¡æ) Net Weight: 1kg,5kg,15kg,18kg,20kg Application: welding low carbon steel and high strength steel structure GB/8110-1995 ISO9001:2000 Fast melting rate, high depositing efficiency, stable arc, little spatter, beautiful seam 1. Properties: Used for welding low carbon steel and low alloy steel structures, especially for welding of thin plates and can be applied to carbon steels, vehicles, construction, shipbuilding, bridge building, etc. 2. Product features: have excellent mechanical performance such as fast melting rate, high depositing efficiency, stable arc, little spatter, beautiful seam. Suitable for all-position welding work. 3. Technical data: A. Chemical composition: C0.06-0.15, Mn 1.40-1.85, Si 0.80-1.15, P
Theory of operating: Ultra pulse treatment is a ¡°fractional¡± treatment that produces thousands of deep, tiny columns in your skin, called micro treatment zones. Ultra pulse is ¡°fractional¡± in that it intensively treats old epidermal pigment cells without effecting any of the surrounding tissue, which reduces healing time(about 24 hours) and promotes the skin¡¯s natural process for creating newer and healthier tissue to replace the damaged tissue. Ultra pulse treatment is a safe, non-invasive procedure that allows you to rediscover the fresh, healthy skin for your beauty. With the super wavelength of 10600nm,the co2 fractional laser machine works by targeting both the epidemis and dermis and delivers tiny and super ablative laser beam into the skin.These super pulse beam work on the skin and then form many micro thermal zone(MTZ) and cause a succession of biochemical reaction.So the pigmented cells are easily expelles and stimulate the collagen to contract and remodel and new collagen to increase.Thus it can improve pigmentation,scar,wrinkles effectively. The scope of treatment: 1. Main function: scar removal 2. All kinds of excavated type of scars (Like traumatic scars, surgical scars and smallpox scar) 3. All kinds of scars, blotches and splashes 4. Shrink large pores, fine wrinkles, skin whitening and stretch marks removal 5.Photoaging and skin excrescence improvement. 6.The medical product (Fractional CO2 Laser) is widely applicable to general surgery, dermatology, gynecology, E.N.T., paediatrics, urology, and used for cutting, cauterizing, carbonization, gasification, hemostasis and other treatment. System Feature ¡¤Red guiding light make operation vision clearer ¡¤For skin resurfacing and for dermatology cut/surgery. ¡¤Various power supply for European, American and area needs. ¡¤Smaller and lighter scanner(volume:7x4x11cm, weight:240g) for more convenient operation. ¡¤With background set for operation time and machine use time. ¡¤With time-accumulater for showing total operation time and machine use time. ¡¤Friendly designed in modular for easy maintenance, with red and green light to guide it. ¡¤Friendly designed for high safety, with warning-alarm-set. Clearly showed on the display screen. ¡¤With energy self-replenishment system, improving the electric flue automatically to ensure real screen. ¡¤With high cost-effective, great quality, best accessories, made by most skilled workers and engineers. ¡¤With cooperation beauty hospital ,each machine should be first perfected in hospital, then customers. ¡¤Committee of China Laser Standard Association, Executive of Laser Branch of china Optical Society. Technical Specifications:Laser Type: CHERNT RF-excited CO2laser Wavelength: 10600nm Beam Delivery: 7-joint arm. Maximum Output Power: 30W(Adjustablel) Optical Beam Quality: TEM Spot Size: 50um-2000um power of the Aimming Beam:less than 5mW Aiming Beam: 635nm Scanning Mode: Randomized Scanning Laser Operating Mode: UltraPluse, CW, Fractional Cooling system :Sealed of water circulation system Pulse energy: 10mj-200mj(stepping :2mj) Pulse Interval: 2ms-100ms(steping:1ms) Scan Area: 5*5mm, 2.5*2.5mm , 1.25*1.25mm 30*30mm, 20*20mm, 10*10mm Power Supply: AC 220V 50Hz/ AC 110V 60Hz WOODEN BOX
Technical parameters: Maximum laser power: 10w Laser wavelength: 10.64¦ìm Laser repetition frequency: 50 khz Standard engraving range: 110mm110mm Engraving depth: 5mm Engraving line speed: 7000mm / s Minimum line width: 0.1mm Minimum characters: 0.4mm Repeat accuracy: 0.01mm Total power: 0.6kw The demand for electricity: 220v / single phase / 50hz / 3a.
Technical parameters: Maximum laser power: 30w Laser wavelength: 10.64ìm Laser repetition frequency: 50khz Standard engraving range: 110mm110mm Engraving depth: 5mm.
The recovery plant is specially designed to recover CO2 from fermentation processes at breweries. This complete CO2 plant was installed in 2001 and it has nominal CO2 removal capacity of 1000 kg/h. The plant has Siemens S 7 control system where operation is carried our via a large 12 " color screen panel with Windows CE operating system. This is a complete CO2 recovery plant and final delivery scope depends on buyers needs. The plant has been in operation only approx 5 years and is still installed and in very good condition. The carbon dioxide plants was designed by Danish Union Engineering (www.union.dk ) and the delivery includes following main components: - 1 Scrubber for gas flushing - 2 Foam catcher vessels - CO2 collection, inflammable - 2 Mehrer TZW 70 CO2 compressors - 2 Carbon filters - 2 Dehydrators - CO2 Liquefier - CO2 Storage Tank - 2 Cooling compressors GEA Grasso GD-3 for R717 - Air cooled condenser for NH2 compressors - Alarm center for CO2 and NH3 concentration - Station for 40 kg CO2 still tank filling - CO2 pumping station from a truck to the factory - CO2 purification tester - Steam heated evaporator for liquid CO2 Detailed technical information available for serious buyers
ínApplicable Materials ¿îThis machine is mainly used for marking; ¿îThe applicable materials include leather, cloth, acrylic, crystal, plastic, rubber, fabric, epoxy, plexiglass, nameplates, package and printing, wood and other non-metal materials; ínApplicable Industry ¿îleather, wood, food, craft, electronic, meter, medicine, communication instruments, package and so on; Laser power 60W/120W Laser type Radio Frequency Whole machine power consume 3.5KW/4KW Min line width 0.015mm Laser wave 1064nm Laser repeat frequency í_20khz Marking speed 7000mm/s Mirror width 200mm*200mm(optional) Power supply AC220í+10% 50HZ/ AC110í+10% 50HZ Cooling way Water cooling and protection system Matching device American radio frequency CO2 laser producer Graphic format supported PLT,BMP,AI Operating temperature 10íµ-26íµ Min character 0.8mm Max resolution 65535 Pulse frequency 20KHZ Marking style Plane, cylinder Repeat precision í+0.01mm Net weight 120kg Machine dimension 1080*530*1335(mm) Net weight 120kg Machine dimension 1080*530*1335(mm)
The CO2 laser cutting machine has many advantages, such as high engraving accuracy, no burrs, and can process any shape. It is widely used in clothing industry, shoe industry and wood carving industry.
The CO2 laser cutting machine has many advantages, such as high carving accuracy, no burrs, and can process any shape. It is widely used in clothing industry, shoe industry and wood carving industry. Stepper motor Strong power, reliable performance, safe and fast, ensure the normal operation of the machine. HIWIN Guide rails Rail works with slider, drive the machine move, with good bearing capacity Cheap and good performance. Without A/D conversion, the digital pulse signal can be directly converted into angular displacement. CO2 laser cutting machine, able to engrave and cut various non-metals, like acrylic, double-color plate, marble, wood, MDF, plywood, textile, leather, glass, paper etc. Widely applied in craft gifts, souvenir, Chinese paper cutting, advertising signs, clothes, furniture and many other industries.
Application of Fractional CO2 Laser Machina: Fractional mode (Aesthetic) + Pulse mode (Surgery) + Gynae mode (Gynecology Optional) Fractional mode: Skin rejuvenation, Wrinkles removal, Pigment removal, Acne treatment. Pulse mode: Sarcoma removal, Nevus removal, Grown nails removal, Skin tags removal. Gynae mode(Optional): Tighten, Lubrication, Sensitivity, Uremic Treatment.