Find Verified Tb6600 Stepper Motor Driver Suppliers, Manufacturers and Wholesalers

Introduction The d2hb882mb is an economical microstepping driver based on patented technology of longs motor.It is suitable for driving 2-phase 4-phase hybrid stepping motors .By using the advanced bipolar constant-current shopping technique , it can output more speed and torque from the same motor, compared with traditional drivers , such as l/r drivers .Its 3-state current control technology allows coil currents to be well controlled and with relatively small current ripple, therefore less motor heating is achieved. Features Low cost and good high-speed torque 14 selectable resolutions Supply voltage up to +80vdc Suitable for-2-phase and 4-phase motors Output current up to 5.86a Dip switch current setting 8different values Optically isolated input signals Pulse frequency up to 200khz Automatic idle-current reduction Small size (107*97*48), weight:1kg

Introduction The d2hb542ma is an economical microstepping driver based on patented technology of longs motor.It is suitable for driving 2-phase 4-phase hybrid stepping motors .By using the advanced bipolar constant-current shopping technique , it can output more speed and torque from the same motor, compared with traditional drivers , such as l/r drivers .Its 3-state current control technology allows coil currents to be well controlled and with relatively small current ripple, therefore less motor heating is achieved. Features Low cost and good high-speed torque Supply voltage up to +45vdc Output current up to 5.86a Optically isolated input signals Automatic idle-current reduction 14 selectable resolutions Suitable for-2-phase and 4-phase motors Dip switch current setting 8 different values Pulse frequency up to 200khz Dip switch current setting 8 different values Small size (122.2*90*33), weight:0.3kg

SD-2H086MB Features Low cost and good high-speed torque 14 selectable resolutions Supply voltage up to +80VDC Suitable for-2-phase and 4-phase motors Output current up to 5.86A Dip switch current setting 8different values Optically isolated input signals Pulse frequency up to 200KHz Automatic idle-current reduction Small size (107*97*48),Weight:1KG

SD-2H044MA Features Low cost and good high-speed torque Supply voltage up to +45VDC Output current up to 5.86A Optically isolated input signals Automatic idle-current reduction 14 selectable resolutions Suitable for-2-phase and 4-phase motors Dip switch current setting 8 different values Pulse frequency up to 200KHz Dip switch current setting 8 different values Small size (122.2*90*33),Weight:0.3KG

Q2HB88M Features (1) High performance, low price (2) Two group 32 channels constant angel and constant torque subdivision. Highest subdivision: 480 (3) The motor phase current is reduced to set current value 100 ms after receiving the last pulse edge (4) Bipolar constant current chopping circuit (5) Opto-isolated input/output (6) Driven current is adjustable continuously from 0.5A/phase to 8A/phase (0.4A/phase to 6.4A/phase) (7) Single power supply, voltage arrange from DC24/V to 80V (DC40V to130V) (8) Highest response frequency: 200Kpps (9) Over voltage protection, overheat protection, over current protection

PMD006P3E is a kind of micro integrated stepper motor microstepping driver, which can be directly installed in the rear 42/57/86 etc series stepper motor, and which has the advantages of small size, strong driving force, and low heat and so on. PMD006P3E stepping motor driver can provide 0~6 continuous adjustable peak current, maximum 128 microstepping, free current which can be adjusted continuously.

We are a manufacturer and can manufacture products according to our customer's design. Currently we are looking for qualified stocking distributors with competitive price and good discount in the world for mutually beneficial long-term relationship. We try our best to support our distributors and business partners to develop more market percentage. Please join us, let's create the glorious future together!

DM420 drive, and 42BYGH stepper motor with the use of Brand: ACT Product type: DM420 type DM420 type subdivision driver of two phase hybrid stepping motor drive, with 12 ~ 36V DC power supply, suitable for driving voltage of 24V ~ 36V, current is less than 2.0A diameter 42 ~ 57 mm two-phase hybrid step motor. The current loop driver adopts AC servo drive subdivision control, motor torque fluctuation a small, low speed operation is very smooth, almost no vibration and noise. High speed torque is also much higher than other phase drives, high positioning accuracy. Widely used in engraving machine, CNC machine tools, packaging machinery demand higher resolution devices. I. overview DM420 type subdivision two-phase hybrid stepper motor drive, with 12 ~ 36V DC power supply, suitable for driving voltage of 24V ~ 36V, current is less than 2.0A diameter 42 ~ 57 mm two-phase hybrid step motor. The current loop driver adopts AC servo drive subdivision control, motor torque fluctuation is small, low speed operation very smooth, almost no vibration and noise. High speed torque is also much higher than other phase drives, high positioning accuracy. Widely used in engraving machine, CNC machine tools, packaging machinery demand higher resolution devices. 1 average current control, two phase sinusoidal current drive output 2 DC 12 ~ 36V power supply 3 opto isolated signal input / output 4, overvoltage, undervoltage, overcurrent, interphase short-circuit protection function 5, eight files subdivision and automatic half flow function 6, eight files output phase current setting 7 has the offline command input terminal 8 the torque of the motor is related to its speed, irrespective of the number of steps the motor has to rotate 9 high starting speed 10. high speed torque Input voltage DC 12 to 40V input The input current is less than 2 Amperes The output current is 0.44A to 2.83A Power dissipation: 40W The working temperature is -10 to 45 degrees; the storage temperature is between -40 and 70 centigrade Moisture can not dew or water Gases are prohibited from flammable gases and conductive dust Weight 70 grams

Export European quality!

Q2hb34ma is a constant angle and constant torque stepper drive. The drive voltage range from dc12v to 40v. It can match 2-phase hybrid stepper motors whose rated current is under 3a and shaft diameter range from 42mm to 86mm. Owe to bipolar constant chopping circuit, it can make motors low noise, operated smoothly. It is widely used in the small size of numerical control device with higher resolution such as carving machine, laser labeling machine, inner laser curving machine and etc. Features high performance, low price 4 channels constant angel and constant torque subdivision, the highest subdivision: 64 highest response frequency: 200kpps the motor phase current is reduced to approximately 50% of the set current value 100ms after receiving the last pulse edge bipolar constant current chopping circuit opto-isolated input/output driven current is adjustable continuously from 0.5a/phase to 3a/phase single power supply, voltage arrange from dc12 to 40v. Size:136x82x25mm Weight:0.5kg

This item inculdes : 1 PC Closed loop Stepper Motor Nema23 57HBM10-1000 4A 110N-cm(155oz-in) 1 PC Mactching Driver WTSS570 Technical Specifications Part No.: 57HBM10-1000 Frame Size: NEMA34 Step Angle: 1.8 degree Voltage: 1.6V Current: 4.0A/phase Resistance: 0.44 Ohm/phase Inductance: 1.2 mH/phase Holding torque: 1.1N.m 155oz-in Rotor inertia: 300g-cm2 Number of wire leads: 4 Weight: 2 kg Length: 77mm

DM542 drive, and 57BYGH stepper motor with the use of Brand: ACT aincot Product type: DM542 type DM542 type subdivision driver of two phase hybrid stepping motor drive, with 18 ~ 50V DC power supply, suitable for driving voltage of 18V ~ 50V, a two-phase hybrid step current is less than 42~86 mm diameter 4.0A stepper motor. The current loop driver adopts AC servo drive subdivision control, torque ripple of motor is small, low speed operation is very smooth, almost no vibration and noise. High speed torque is also much higher than other phase drives, high positioning accuracy. Widely used in engraving machine, CNC machine tools, packaging machinery demand higher resolution devices. I. overview DM542 type subdivision two-phase hybrid stepper motor drive, with 18 ~ 50V DC power supply, suitable for driving voltage of 18V ~ 50V, a two-phase hybrid step current is less than 42~86 mm diameter 4.0A stepper motor. The current loop driver adopts AC servo drive subdivision control, motor torque fluctuation is small, low speed running smoothly and almost no vibration and noise. High speed torque is also much higher than other phase drives, high positioning accuracy. Widely used in engraving machine, CNC machine tools, packaging machinery demand higher resolution devices. 1 average current control, two phase sinusoidal current drive output 2 DC 24 ~ 50V power supply 3 opto isolated signal input / output 4, overvoltage, undervoltage, overcurrent, interphase short-circuit protection function 5, fifteen files subdivision and automatic half flow function 6, eight files output phase current setting 7 has the offline command input terminal 8 the torque of the motor is related to its speed, irrespective of the number of steps the motor has to rotate 9 high starting speed 10. high speed torque Input voltage DC 18 to 50V input The input current is less than 4 Amperes The output current is 1.0A to 4.2 Power dissipation: 80W; internal insurance: 6 The working temperature is -10 to 45 degrees; the storage temperature is between -40 and 70 centigrade Moisture can not dew or water Gases are prohibited from flammable gases and conductive dust Weight 200 grams

Dm860 type subdivision two-phase hybrid stepper motor drive, with 24 ~ 80v dc power supply, suitable for driving voltage of 24v ~ 80v, current is less than 8.0a diameter 57 ~ 110 mm two-phase hybrid step motor. The current loop driver adopts ac servo drive subdivision control, motor torque fluctuation is small, low speed operation very smooth, almost no vibration and noise. High speed torque is also much higher than other phase drives, high positioning accuracy. Widely used in engraving machine, cnc machine tools, packaging machinery and other high requirements on the equipment. I. Overview Dm860 type subdivision two-phase hybrid stepper motor drive, with 24 ~ 80v dc power supply, suitable for driving voltage of 24v ~ 80v, current is less than 8.0a diameter 57 ~ 110 mm two-phase hybrid step motor. The current loop driver adopts ac servo drive subdivision control, motor torque fluctuation is small, low speed operation very smooth, almost no vibration and noise. High speed torque is also much higher than other phase drives, high positioning accuracy. Widely used in engraving machine, cnc machine tools, packaging machinery and other high requirements on the equipment. 1 average current control, two phase sinusoidal current drive output 2 dc 24 ~ 80v power supply 3 opto isolated signal input / output 4, overvoltage, undervoltage, over-current, overheating, interphase short-circuit protection 5, fourteen files subdivision and automatic half flow function 6, eight files output phase current setting 7 has an offline signal transmission terminal 8 high starting speed, high speed torque I. Electrical parameters Input voltage Dc 24 ~ 80v input Power dissipation: 80w; internal insurance: 10a Temperature The working temperature is -10 to 45 deg c; the storage temperature is between -40 and 70 deg c No dew, no water Flammable gas and conductive dust are prohibited Weightabout 500 grams

Vid78 multi-polar stepper motor series designed based on vid new design electromagnetic micro-motor system.(us patent 20080018208. Chinese patent zl2006 20130640.5 and international patent is under application).Characterized in extremely low noise, high torque and high precision are leading by advanced technology for new generation cluster step motor. 1000pcs/ctn, 10.5kg, 430*314*476mm

With OSM's huge assortment of High-Torque Stepper Motors, a customer can select the most cost-effective solution, never sacrificing quality or system performance. The stepper motors product line ranges from the smallest Nema 8 stepper motors with 2.5 oz. inches of torque, to the largest Nema 42 stepper motors with up to 5,700 oz. inches of torque! A high-Torque Stepper Motors has a 1.8-degree step angle as standard, yet other step angles are available. Four, six and eight-lead configurations are standard for OSM's stepper motor product line, and are model dependent. Other options available are conduit boxes, special stepper motors windings, shaft modifications, as well as cable, connector, encoder, brake, and gearbox adders.

Stepper motors.

1.Inherently a digital device, number of pulses determine distance, frequency sets the speed. 2.Drift free. 3.The step angle error is very small and non-cumulative. 4.Rapid response to starting, stopping, and reversing. 5.Brushless design for reliability, simplicity. 6.High torque per package size. 7.Stable at zero speed. 8.Holding torque at standstill. 9.Can be stalled repeatedly and indefinitely without damage. 10.No extra feedback components required (encoders can be added for additional advantages). 11.Bidirectional operation. Standard cotton box.