Find Verified Coated Technical Urea For Scr Systems Suppliers, Manufacturers and Wholesalers

Description: Automotive Grade Urea is a high-purity urea solution specifically formulated for use in diesel engines equipped with Selective Catalytic Reduction (SCR) systems. This product helps reduce nitrogen oxide (NOx) emissions, supporting compliance with emission regulations and promoting environmental sustainability. Automotive grade urea is commonly used in Diesel Exhaust Fluid (DEF), also known as AdBlue or AUS32, to improve air quality by reducing harmful exhaust gases. Specifications: Nitrogen (on dry basis): Minimum 46.3% wt Biuret: Maximum 0.9% wt Moisture: Maximum 0.5% wt Alkalinity as NH3: Maximum 0.02% wt Aldehydes: Maximum 10 mg/kg Insoluble Matter: Maximum 60 mg/kg Phosphate (PO4): Maximum 1.5 mg/kg Aluminum (Al): Maximum 1.5 mg/kg Calcium (Ca): Maximum 1.5 mg/kg Applications: Suitable for use in diesel vehicles equipped with SCR-(AdBlue) technology Effective in reducing NOx emissions in line with Euro VI and other emission standards Packaging Options: The product is available in 25 kg, 50 kg, and 1000 kg bags, or in bulk quantities, according to customer requirements.

Neodymium magnets (also known as NdFeB, Neo or NIB magnets), are strong permanent magnets made from an alloy of neodymium, iron & boron. Part of the Rare-Earth magnet family, they have the highest magnetic properties of all permanent magnets. Due to their high magnetic strength and relatively low-cost, they are the preferred choice for many consumers, commercial, industrial and technical applications.NdFeB is divided into sintered NdFeB and bonded NdFeB. Bonded NdFeB is magnetic in all directions and corrosion resistance and is divided into Bonded Compression NdFeB Magnet and Bonded Injection NdFeB Magnet; while sintered NdFeB is easy to corrosion, the surface requires coating, generally divided into axial and radial magnetic charging. Advantages of Sintered NdFeB Magnet : 1. Very hard and brittle, high diamagnetic resistance, high cost / performance ratio, not suitable for high working temper ature; 2. Magnetic performance is higher than that of the rare earth cobalt permanent magnet, the residual magnetic induction strength, magnetic induction coercivity, the maximum magnetic energy product is very high, is the current magnetic performance of the best permanent magnet; 3. High cost performance.

Product Name: Ferrous Sulphate Heptahydrate Molecular Formula: FeSO4. 7H2O CAS No.: 7782-63-0 Mol Weight: 278.05 Usage and Dosage: 1. Industrially: ferrous sulphate heptahydrate is mainly used as a precursor to other iron compounds. It is a reducing agent, for the reduction of chromate in cement. 2. Nutritional Supplement: Together with other iron compounds, ferrous sulphate is used to fortify foods and treat iron-deficiency anemia. Constipation is a frequent and uncomfortable side effect associated with the administration of oral supplements. Stool softeners often are prescribed to prevent constipation. 3. Colorant: Ferrous sulphate can also be used to stain concete and some limestones and sandstones a yellowish rust color. 4. Water Treatment: Ferrous sulphate has been applied for the purification of water by flocculation and for phosphate removal in municipal and industrial sewage treatment plants to prevent eutrophication of surface water bodies. Storage: Storage Store in cool, dry, well ventilated area, removed from oxidising agents (eg. hypochlorites), acids, metals and foodstuffs. Ensure containers are adequately labelled, protected from physical damage and sealed when not in use. Large storage areas should have appropriate ventilation systems. Precaution: Flammability Non flammable. No fire or explosion hazard exists. Packing: Net weight 25kgs, 50kgs per each plastic woven bag Technical Specification Appearance: Light green crystalline powder Fe 19.7%min Pb 20 ppm max As2 ppm max Cd 5 ppm max Size Crystalline Powder

per annum. Price for volume over the MoQ 30 Million boxes is negotiable. Payment by L/C 100% at sight, transferable, irrevocable and confirmed. Product Name: Disposable Vinyl/Nitrile Blended Examination Gloves Single use, non-sterile, no measuring, Latex free Sizes: XS, M, L. XL. XXL Color: Blue, Green Structure: 5 fingers, beaded cuff for easy donning, ambidextrous Surface: Smooth The Vinyl/Nitrile Blended glove is a new type of synthetic glove that was developed based on the vinyl glove production technology. Its material is compounded with PVC paste and Nitrile latex, so the finished production has the advantage of both PVC and Nitrile gloves. Comparing with the vinyl gloves, the Vinyl/Nitrile Blended glove can better satisfy the users demands, it feels softer, more flexible and more comfortable when wearing. Intended purpose: The examination glove is disposable non-sterile device intended for medical purpose that is worn on the examinerâ??s hand or finger to prevent contamination between patient and examiner. Medical Device Quality Management System EN ISO 13485 Certificate, ISO 9001 Quality Management System Certificate - 2 FDA FDA Registration Information - 510K Product 510K Biocompatibility Test Report EU CE Certificate (DOC, Technical Documentation Review Report )

Let the deliciousness of Cannon Balls rain down on your tongue. Tender balls of milk chocolate with a crunchy coating of sugar and chocolate crisp. Every crunchy bite will make you want more. Packaging = English, Bahasa Indonesia. Port of Loading: Semarang, Indonesia. Note: We could paste sticker on each pack should there is any additional information needed (importer name, information in other language, etc). Please inquire us for further details.

SVR3L is made from latex harvested from our rubber plantation. It can meet customer strict requirement about some of technicalities such as: the PO, Color (Lovibond), SVR3L is made from latex harvested from our rubber plantation. It can meet customer strict requirement about some of technicalities such as: the PO, Color (Lovibond), Latex is preserved by ammonia or sodium sulfite. Then coagulated with formic acid, followed by shredding by passing through a rolling mill, washing system and hash.

SVR3L is made from latex harvested from our rubber plantation. It can meet customer's strict requirement about some of technicalities such as: the PO, Color (Lovibond), SVR3L is made from latex harvested from our rubber plantation. It can meet customerâ??s strict requirement about some of technicalities such as: the PO, Color (Lovibond), â?¦ Latex is preserved by ammonia or sodium sulfite. Then coagulated with formic acid, followed by shredding by passing through a rolling mill, washing system and hash. After the crumb rubber is dried, it will be compressed into blocks and packed in polyethylene bags

Automatic series for customized Spider hand delta robot for Parallel robot-3c industry, Parallel robot - food industry, Parallel robot - medicine industry, Parallel robot - Daily Chemical Industry, Other standard automation systems : Automatic bagging, automatic sorting, automatic packing, automatic palletizing, automatic palletizing and automatic loading ... any want to automaitc same this kind ,offer training after-sale service ! whole life maintenance!

Chickpeas also known as Black Chana was first grown in Australia as a commercial crop in Goondiwindi during the early 1970s. It is now an important crop in northern farming systems (NSW and Queensland) and becoming more widely grown in southern (Victoria and South Australia) and western (Western Australia) regions. Also known as Bengal gram, Black Chana grain is exceptionally high in protein and has a low glycemic index making it an excellent protein for people with Diabetes. Black Chana, are light to dark brown colour. They are in the 6 to 7mm range, with a thick seed coat. Desi Chickpeas produced are split in half to make Chana Dahl, this split form are ground into flour called Besan.

* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.

PC regrind mixed color - Origin Japan Technical applications If you do not know what common applications of PC plastic are, in addition to the use of food containers, drinking cups, bottles or travel suitcases, PC plastic is also used in engineering fields such as making dashboards. control and system of pipes or cardboard for writing liner, bulletproof glass, spare parts for slide show equipment. However, with technical application, PC plastic has certain disadvantages with low durability, so it is only suitable as accessories. MATERIAL: PC regrind mixed color CATEGORY: PC TYPE: egrind GRADE: mixed color SPECIFICATION: From sheet and It's a part of an electrical appliance Origin: Japan LOADING WEIGHT: 24 Ton FOB (USD/Ton): 900$ - 1100$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days

Technical applications If you do not know what common applications of PC plastic are, in addition to the use of food containers, drinking cups, bottles or travel suitcases, PC plastic is also used in engineering fields such as making dashboards. control and system of pipes or cardboard for writing liner, bulletproof glass, spare parts for slide show equipment. However, with technical application, PC plastic has certain disadvantages with low durability, so it is only suitable as accessories. MATERIAL: PC regrind natural color CATEGORY: PC TYPE: regrind GRADE: natural color SPECIFICATION: From sheet and It's a part of an electrical appliance Origin: Japan LOADING WEIGHT: 24 Ton FOB (USD/Ton): 1200$ - 1400$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days

PC-GF 20% regrind black color - Origin Japan has been processed into plastic particles, which are very convenient for transportation as well as in the recycling process to create new products. We always provide the same products as reality, and we use 100% real images. Technical applications If you do not know what common applications of PC plastic are, in addition to the use of food containers, drinking cups, bottles or travel suitcases, PC plastic is also used in engineering fields such as making dashboards. control and system of pipes or cardboard for writing liner, bulletproof glass, spare parts for slide show equipment. However, with technical application, PC plastic has certain disadvantages with low durability, so it is only suitable as accessories. MATERIAL: PC-GF 20% regrind black color CATEGORY: PC-GF 20% TYPE: regrind GRADE: black color SPECIFICATION: From sheet and It's a part of an electrical appliance Origin: Japan LOADING WEIGHT: 24 Ton FOB (USD/Ton): 600$ - 900$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days

1. Cost advantage: we are specialized in sublimation materials, such as phone cases, designing and manufacturing in one stop service, so we can give you lowest price 2. Technology advantage: we have strong capabilities, and specialize in providing comprehensive technical support services for manufacturing of Design precise plastic injection, surface coating, silk-screen, pad printing, IMD Tech, and so on, and we have an experienced professional team, it keeps our capabilities of innovation and application. 3.Quality advantage:All products must pass the inspection by professional QC team. 4.Warranty advantages: Free exchange guarantee, if you receive what is different from your order or is too bad to accept, please contact us as soon as possible, we promise to solve your problem in 24 hours.

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

Urea ammonium nitrate solution, commonly referred to as UAN, is a liquid nitrogen fertilizer which is made up of a mixture of urea, ammonium nitrate and water. Nitrogen fertilizer is responsible for the production of amino acids and proteins and indirectly supports the production of vitamin B. Nitrogen application is the main factor to improve plant growth, development and yield of all crops. Usage: The use of modern crop application methods of UAN are designed to provide very precise application of UAN to the crop. Furthermore, UAN applications can provide better economics for the farmer than dry fertilizer applications because the farmer can add other crop protection products like herbicides, insecticides and fungicides to the UAN and can be applied to the crop in a single application.