EAP 66 Engine: PERKINS Engine Model : 1103A-33TG2 Stand By kVA: 66 Stand By kW : 52,8 Prime kVA: 60 Prime kW : 48 Rated Current : 86,4 Engine - PERKINS heavy duty diesel engine - 12V starter and charge alternator - Replaceable air, fuel and oil filters - Mechanical governor control - Tropical type radiator - Flexible fuel hose - Oil drain valve and extension hose - Industrial type silencer and steel compensator - Maintenance-free starter battery - Water jacket heater - 1500 rpm engine speed Alternat�¶r - IP 21-23 Protection Standard - H Insulation Class - 50 Hz Frequency - 4 pole brushless synchronous type alternator - Automatic Voltage Regulator (AVR) - 400/230V AC Output Voltage - 1500 rpm Sound Proof Canopy and Chassis - Convenient design for easy lifting and carrying - High standard sound proof canopy design - Modular design with easily removable nuts - bolts - Lockable doors - Transparent window for watching Control Panel - Electrostatic powder painted, providing protection against harsh weather conditions - Emergency STOP button - Fuel tank inside the chassis - Anti-vibration wedges (engine - chassis and chassis â?? ground) Optional - Thermal magnetic CB (for automatic models) - Super Silent Canopy - Mobile Generator Sets - Automatic fuel filling system - Synchronization panel - 3 Pole and 4 Pole ATS (Automatic Transfer Switch) - Fuel Heater, Oil Heater - External fuel tank and automatic fuel filling system - Fuel - water separator filter - Remote monitoring and control system Engine PERK�°NS Engine Model 1103A-33TG2 Number of Cylinders 3 Inline Injection System Direct Compression Ratio 17.25 : 1 Bore 105 Strok 127 Displacement Lt 3,3 Air Intake Turbocharged - Air to Air Cooled Speed (RPM) 1500 Oil Capacity Lt 8 Standby Power kw / Hp 60,5 / 82 Prime Power Hp 55 / 74 Fuel Type Euro Diesel Governor System Mechanical Cooling System Water Cooling Coolant Capacity Lt 10,2 Fuel Consumption (lt / h) Lt Full Load 14 Lt %75 LOAD 10,4 Lt %50 LOAD 7,2 Frequency Hz Power kVA 66 Voltage V 230 / 400 V Number of Phases 3 Automatic Voltage Regulator (A.V.R.) AS440 Voltage Regulation �±1% Insulation Class H Protection Standard IP22-IP23 Power Factor 0,8 Weight (Silent) Kg 1200 Weight (Open) Kg 1030 Width (Silent) Mm 1000 Length (Silent) Mm 2400 Height (Silent) Mm 1500 Fuel Tank Capacity Lt 180 1 Standby Power : The max power available during a variable electrical power sequence, under the stated operating conditions, for which a generating set is capable of delivering in the event of a utility power outage. Overloading isnâ??t permissible. 2 Prime Power : The maximum power which a generating set is capable of delivering continuously whilst supplying a variable electrical load. Average load should be 70%. The generator can be overloaded 10% for 1 hour per 12 hrs.
EAP 22 Engine: PERKINS Engine Model : 404A-22G1 Stand By kVA: 22 Stand By kW : 17,6 Prime kVA: 20 Prime kW : 16 Rated Current : 28,8 Engine - PERK�°NS heavy duty diesel engine - 12V starter and charge alternator - Replaceable air, fuel and oil filters - Mechanical governor control - Tropical type radiator - Flexible fuel hose - Oil drain valve and extension hose - Industrial type silencer and steel compensator - Maintenance-free starter battery - Water jacket heater - 1500 rpm engine speed Alternat�¶r - IP 21-23 Protection Standard - H Insulation Class - 50 Hz Frequency - 4 pole brushless synchronous type alternator - Automatic Voltage Regulator (AVR) - 400/230V AC Output Voltage - 1500 rpm Sound Proof Canopy and Chassis - Convenient design for easy lifting and carrying - High standard sound proof canopy design - Modular design with easily removable nuts - bolts - Lockable doors - Transparent window for watching Control Panel - Electrostatic powder painted, providing protection against harsh weather conditions - Emergency STOP button - Fuel tank inside the chassis - Anti-vibration wedges (engine - chassis and chassis ground) Optional - Thermal magnetic CB (for automatic models) - Super Silent Canopy - Mobile Generator Sets - Automatic fuel filling system - Synchronization panel - 3 Pole and 4 Pole ATS (Automatic Transfer Switch) - Fuel Heater, Oil Heater - External fuel tank and automatic fuel filling system - Fuel - water separator filter - Remote monitoring and control system Engine PERKINS Engine Model 404A-22G1 Number of Cylinders 4 Inline Injection System Direct Compression Ratio 23.3:1 Bore 84 Strok 100 Displacement Lt 2,21 Air Intake Naturally Aspirated Speed (RPM) 1500 Oil Capacity Lt 10,6 Standby Power kw / Hp 20,6 / 27,8 Prime Power Hp 18,7 / 25,2 Fuel Type Euro Diesel Governor System Mechanical Cooling System Water Cooling Coolant Capacity Lt 14 Fuel Consumption (lt / h) Lt Full Load 5,3 Lt %75 LOAD 4 Lt %50 LOAD 2,9 Frequency Hz Power kVA 22 Voltage V 230 / 400 V Number of Phases 3 Automatic Voltage Regulator (A.V.R.) AS440 Voltage Regulation ±1% Insulation Class H Protection Standard IP22-IP23 Power Factor 0,8 Weight (Silent) Kg 720 Weight (Open) Kg 590 Width (Silent) Mm 950 Length (Silent) Mm 2000 Height (Silent) Mm 1200 Fuel Tank Capacity Lt 125 1 Standby Power : The max power available during a variable electrical power sequence, under the stated operating conditions, for which a generating set is capable of delivering in the event of a utility power outage. Overloading isnâ??t permissible. 2 Prime Power : The maximum power which a generating set is capable of delivering continuously whilst supplying a variable electrical load. Average load should be 70%. The generator can be overloaded 10% for 1 hour per 12 hrs.
Style: Dried Species: Jackfruit Smell: Aromatic, Natural Shape: Complete / Slice Drying process: AD Preservation Process: Other Cultivation Type: General, Greenhouse, Organic, Cleaning Packaging: Bulk, vacuum pack, pa / pe bag Max. Humidity (%): 5 Certification: HACCP Weight / kg): 0.1 Life time: 18 months In orgin: Vietnam Brand: 99 Gold Data Model: DJ0001 Product's name: Dried Jackfruit Color: Yellow Ingredient: 100% Fruit Class: Top Grade Pack: PA / PE bags Quality: 100% NATURAL Storage: Cool dry place
Take 100gms of instant jam mix in a vessel and add 150ml of water(For 1 cup of jam mix 1 1/4cup of water). Mix well without lump formation. Boil the mix for 5 mins and reduce the burner level to simmer. Hold it for 5 minutes without stirring or until it reaches setting point of 1040C at low flame. Allow the jam mix to cool. Transfer the mix to sterilized container.
EnzoPlast TS 8 is a Chemically Modified, Vegan, Gluten-Free, Plant- based, Non-GMO oxidized tapioca starch. EnzoPlast TS 8 is characterized by its exceptional functional properties such as low viscosity, high stability, clarity, film forming, low temperature stability and binding properties. EnzoPlast TS 8 is widely used in bakery products, frozen foods, dairy products, confectioneries, breading and coating applications, etc., It is 100% naturally made which does not have any preservatives and Mono sodium Glutamate (MSG). APPLICATIONS ï?· EnzoPlast TS 8 is used as stabilizer in milk products, ice cream desserts, puddings, fillings, etc.,It is also used in the production of flavoured yoghurts, flavoured milk drinks, whipped cream, low fat cream, etc., ï?· EnzoPlast TS 8 can also be used as fat-mimetic and partial replacement of casein in cheese products with improved stretchability and hardness ï?· EnzoPlast TS 8 is recommended for salad and vegetable sauces, salad dressings, sugar syrups, sauces for canned meat and vegetables, mayonnaise, soups, puddings, fruit filling for confectionery products, jellies, fruit paste candy and soft gummies ï?· In baking industry, EnzoPlast TS 8 expands and improve physical possessions and physical properties of dough, increases its capability to hold gases FROZEN FOODS EnzoPlast TS 8 is used in frozen foods, refrigerated or canned foods, generally for thickening, temperature stability and control the flow in the purpose food. EnzoPlast TS 8 are used for improved adhesion and improved stability, reputedly because of covalent bonding with protein on the substrate surface. FUNCTIONAL PROPERTIES EnzoPlast TS 8 forms highly thixotropic pastes with stiff texture, which is related to its gelling capability Low gelatinization temperature and viscosity, clarity, and soft gel texture are attributes of EnzoPlast TS 8 used in breading and related applications When heated in water, EnzoPlast TS 8 form clear fluid sols. On cooling, however, the sols made by cooking EnzoPlast TS 8 is more stable or resistant to thickening and forming gels or pastes EnzoPlast TS 8 is used in formulated products. They also are used in starch batters and in breaded foods, where they improve adhesion of the batter to meat and fish Gum confections made with EnzoPlast TS 8 have longer shelf life, better gelling characteristics, increased clarity, better taste, and quicker drying Used in batters and breading for coating various food stuffs, in confectionery as binders and film formers, in dairy products as texturizers EnzoPlast TS 8 is often used for coating, sealing, batter binding, emulsification, and dough conditioning in baking and other food products.
Foodix - Offering Instant Mysore Pak Mix. Product Description 1. In a pan, empty the contents of this pack and add 70 ml (Approx. 1/2 cup) of water and mix well without lumps. 2. Cook for 10 minutes in medium flame with continuous stirring & add ghee (Approx. 200 ml) at frequent intervals during the process. 3. Apply Ghee in a plate & transfer the Mysore Pak. Decorate with Nuts/Dry fruits of your choice if needed. Cut into pieces once it is cooled.{Ideally cutting is done when it is slightly warm only to avoid breakage} Serving size Approx.25g Grams of MysorePak, can be cut to 14 pieces.
ECO-FRIENDLY COCONUT SHELL BOW - Ingredients: Only coconut shell and coconut oil with no paint and any chemicals. - - - - Processing process: manually trimmed and polished with sandpaper through many stages in the Big Coconut area of Vietnam, Ben Tre. Finally, cover with a layer of coconut oil on the surface to help the bowl smell black coconut fragrant. - Order laser logo printing at the FACTORY PRICE! - DIRECTIONS FOR USE * Before you use your coconut bowl, rinse it in water at room temperature. * Polish your coconut bowl from time to time with coconut oil. * Not dishwasher friendly. Wash off with soap and water. Do not soak for long time. * Do not overheat your coconut bowl and do not use it in the microwave, oven or dishwasher. * Do not leave the coconut bowl in a place with high humidity, so keep in a cool dry place before storing in the refrigerator.
- Ingredients: Only coconut shell and coconut oil with no paint and any chemicals. - - - - Processing process: manually trimmed and polished with sandpaper through many stages in the Big Coconut area of Vietnam, Ben Tre. Finally, cover with a layer of coconut oil on the surface to help the bowl smell black coconut fragrant. - Order laser logo printing at the FACTORY PRICE! - DIRECTIONS FOR USE * Before you use your coconut bowl, rinse it in water at room temperature. * Polish your coconut bowl from time to time with coconut oil. * Not dishwasher friendly. Wash off with soap and water. Do not soak for a long time. * Do not overheat your coconut bowl and do not use it in the microwave, oven, or dishwasher. * Do not leave the coconut bowl in a place with high humidity, so keep it in a cool dry place before storing it in the refrigerator.
LIMPET SEASHELL Size: 5-5.5cm, 5.5-6cm, 6-7cm, 7-8cm Usages: Ornament making, jewelry making, home d�©cor, center pieces, aquariums, gifts, and collecting 100% Natural 1- Prevents and heals cracks thanks to the benefits of mother of pearl 2- Contains milk loss by avoiding your clothes from tarnishing 3 - maintaining nipple in breast milk which is inherently healing and antiseptic. 4- Relieves the burning sensation when seashell rests, mother of pearl cools during feeding time. After each feeding, carefully put the skin of the nipple in the hollow part of it. You can wear it after applying your skin care cream. The shell is held by your bra. Wash the seashell daily with soap and rinse with clear water.
Las 4NF- Lactose Substitute Non- Fat Solid is an Enzymatically Modified, Clean Label, Vegan, Gluten-Free, Plant-based and Non-GMO starch used as a special additive for improving texture of Paneer. It is 100% naturally made which does not have any preservatives and Mono sodium Glutamate (MSG). APPLICATIONS 1. Milk is first heated (pasteurizing) to 85�°C and held for 12 minutes. 2. Add 2% to 20% of LAS 4NF based on the Protein Content of the Milk to the pasteurized milk and stir slowly to ensure full dissolving at 80C. 3. LAS 4NF itself contains coagulant. If necessary add coagulant as per the costumer requirement slowly to the milk by slow stirring, maintaining the temperature at 70�° C. 4. Keep Slow stirring for complete separation of solids and whey. (Indication: Whey will turn to light green color and small lumps of solids will settle down) 5. The whey water is filtered through a fine mesh of muslin cloth. The separated particles remain in muslin cloth and it is held in hoofer. 6. Apply pressure on the covered solid spread evenly on hoofer, with a flat lid in lay till water droplets stop. 7. Then the Paneer is pre-cooled in pure water at room temperature for 10 mins or till the external sides can be held in hand water for 10 mins , then dip in chilled water for 4 hours. DOSAGE Use 2 to 20% of LAS 4NF of total batch size, based on the protein content of the milk. For lower protein content in the milk higher LAS 4NF need to be used.
Relish this delicious ready to eat halwa sweet which takes only a few minutes to prepare EASY TO COOK: Add hot milk to this and be prepared to enjoy Indian delicacy anytime you want FULLY NATURAL: This is vegetarian, gluten-free as well as 100% all-natural food, which is free from preservatives, MSG, and food colors AUTHENTIC INDIAN FOOD: Enjoy the authentic taste of India at the ease of your home with this quick and hassle-free packaged food PRODUCT OF INDIA: This ready to cook food is an Indian product, which is sourced fresh directly from the manufacturers and delivered to your doorstep Directions : In a pan, add 300ml (Approx.. 2 Cups) of water and empty the contents of this pack into the water and mix well without lump formation Cook for 10 minutes in medium flame with continuous stirring & adding ghee at the last stage of the process Apply Shee in a plate & transfer the Halwa. Decorate with Nuts / Dry fruits of your choice if needed. Cut into pieces once it is cooled
LAS 5NF is a Lactose Substitute Non- Fat Solid is an Enzymatically Modified, Clean Label, Vegan, Gluten-Free, Plant-based and Non-GMO starch used as curdling and thickening agent in Flavored milk,Ice cream,Gelato,Cottage cheese, Vegan Cheese,Sour cream,Whipped cream and Vegan butter. It is 100% naturally made which does not have any preservatives and Mono sodium Glutamate (MSG). APPLICATIONS 1. First add 4% to 10% of LAS 5NF based on the Protein Content of the Milk in cold (4�°C to 36�°C) condition. Dissolve it well without Lump formation. 2. Mix 10% of extra water to total mix and heat the milk mixer to 85�°c & hold for 12 min with continuous stir .The product is settle down when stir is not good. 3. Cool the pasteurized milk to 43�°c to 45�°c with slow stir and then add required quantity of culture and stir it slowly for even mixing of culture. 4. Then keep it in an incubator @ 43�°C for 6 hours and transfer it to chiller. DOSAGE For excellent results, use 4 to 10% of LAS 5NF of total batch size, based on the protein content of the milk. For lower protein content in the milk higher LAS 5NF need to be used.
Foodix- Offering Instant Mix for Murukku. One of the Most wanted Indian Snacks and widely prepared when the festively time Like Diwali. Preparation 1. Empty the contents of this pack and mix it with 2 cups (Approx. 300ml) of water. Then add 25g of butter or two tablespoons of oil (30 ml) and make it into a dough.2. Heat oil in a pan3. Insert the dough into the mould and press the mould to make spirals either on a cloth, butter paper, foil or flat hold ladle.4. Place the ladle in the oil or remove the Murukku and drop gently in the hot oil. Fry until golden brown and crisp.5. Drain the fried MURUKKU on the kitchen tissue to remove excess oil. Cool them completely. Store them in an airtight container for delicious Murukku. Can be used for preparing Spicy/Sweet Murukku. Add chilli powder/ sugar as per your preference Serving size This pack gives 50 pieces of Murukku (6 cm diameter)
THINTEXOTM-Modified Starch Low viscosity modified starch for warp yarn sizing SPECIFICATIONS Appearance : off white to cream colour fine free flowing powder Solubility : Insoluble in cold water pH value( 15 % aqu. soln) : 5 to 7 Viscosity of 15% soln : Max 60 cPs (Brookfield viscometer ( Spl.2 , rpm:100 @ 80oc) LVDV II+ pro) Moisture content (w/w) : Max 13% Ash content (w/w) : Max 0.5% Sieve Retention (60 Mesh) : Max 1% Bulk density (gm/ml) : 0.45 to 0.55 SPECIAL FEATURES : Constant viscosity. Optimum penetration & film formation. Better flexible film . Easily de sizable product . Warp- break reducer. STORAGE Keep away from direct sunlight and store in a cool, dry, and well-ventilated place. STABILITY - Stable for one year from the date of manufacture PACKING - Available in 50Kgs Net weight PP Bags with a moisture-proof line inside.
n product. Texture Feature: Light creamy to white color fine free flowing powder, free from rancidity and foreign matter. Specification : S.No Parameters Specifications 01 Appearance Slightly red color, fine powder 02 Solublity In Cold Water Min. 20% 03 pH Value OF 20% Solution 5.0 To 7.0 04 Viscosity Of 20% Solution In Brookfield Lvdvii+pro Viscometer ( Spindle No : 2 , Rpm 100 , Temp 800c) 50 to 150 cPs 05 Moisture Content, (w/w) Max. 13% 06 Bulk Density, Gm/ml 0.55 To 0.7 07 Ash Content Max. 10 % Application : Coat a piece of washed chicken in this dry mix powder. Then dip the coated chicken piece in the batter* until evenly wet. *Batter preparation: Dissolve 50 g instant crispy fry mix in 85 ml of water. Again roll the dipped chicken piece in a dry mix powder. Fry these coated pieces in a hot oil until it turns golden brown color. Note:100 g of instant crispy fry mix is enough for making 250 g of crispy runchy chicken. Storage : Exhibits excellent stability when stored in closed container under cool and dry ventilated place . Avoid direct sun light. Packing : Available in 25Kgs net weight paper bags with moisture proof line inside.
Oxidized starch - TS is a Chemically Modified, Vegan, Gluten-Free, Plant-based, Non-GMO tapioca starch. Oxidized starch is characterized by its exceptional functional properties such as low viscosity, high stability, clarity, film forming, low temperature stability and binding properties. Oxidized starch is widely used in bakery products, frozen foods, dairy products, confectioneries, breading and coating applications, etc., It is 100% naturally made which does not have any preservatives and Mono sodium Glutamate (MSG). FUNCTIONAL PROPERTIES Oxidized starch forms highly thixotropic pastes with stiff texture, which is related to its gelling capability Low gelatinization temperature and viscosity, clarity, and soft gel texture are attributes of oxidized starch used in breading and related applications When heated in water, Oxidized starch form clear fluid sols. On cooling, however, the sols made by cooking oxidized starch are more stable or resistant to thickening and forming gels or pastes Oxidized starch is used in formulated products. They also are used in starch batters and in breaded foods, where they improve adhesion of the batter to meat and fish Gum confections made with oxidized starch have longer shelf life, better gelling characteristics, increased clarity, better taste, and quicker drying Used in batters and breading for coating various food stuffs, in confectionery as binders and film formers, in dairy products as texturizers Oxidized starch is often used for coating, sealing, batter binding, emulsification, and dough conditioning in baking and other food products.
SizeMagikTM-LP4 - LOW PICK UP ONE-SHOT PRODUCT DESCRIPTION An unique copolymer sizing agent for cotton compact yarn. Special product for air jet loom. Heavy fabric constructions are easier to weave at low-size add-ons using SizeMagik-LP4. The low add-on also permits greater protection on high-speed looms expensive reeds and sensitive mechanical parts life. SPECIFICATIONS 1. Appearance: Off white Granules 2. Solubility: Soluble at 800C 3. Viscosity of 4% solution: 10 to 30 cPs (Brookfield viscometer LVDV II+ pro -Spl.2 , rpm:100 @ 80oc) 4. Ash content (w/w) : Max 3% 5. Bulk density (gm/ml) : 0.65 to 0.85 COOKING METHOD 1. Fill the required quantity of water in the cooker. 2. Gradually sprinkle SizeMagikTM-LP4. 3. Add the required quantity of softener. 4. Close the pressure cooker lid. 5. Open the steam value and cook to @ 120�¯�¿�½?�?�ºC or 35psi. 6. Retain in the cooker for 15 to 20 minutes. 7. Then transfer the size mix to storage. ECONIMICAL ADVANTAGES Yarn abrasion resistance is an important factor affecting weave ability. The friction between the warp to warp and warp to the weft is important in determining the weaving quality. Another important abrasion point in the loom is mechanical parts (Reed, Dropper pin, Heald wire, Weft picking element). Compare with other conventional size mixes and one-shot size products SizeMagik-LP4 gives better abrasion resistance strength. DE-SIZING Easily de-sizable product with hot alkali treatment. STORAGE Keep away from direct sunlight and store in a cool, dry, and well-ventilated place. STABILITY Stable for one year from the date of manufacture. PACKING Available in 50Kg net weight PP bags with moisture-proof liner inside.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
About THE Product : Blast furnace slag is used in the production of cement (iron Portland and blast furnace cement). Air-cooled blast furnace slag is formed by allowing the molten slag to cool relatively slowly under ambient conditions; final cooling can be accelerated with a water spray. The cooled material is hard and dense, although it can have a vesicular texture with closed pores. After crushing and screening, air-cooled slag can be used in several applications. Granulated slag is formed by quenching molten slag in water to form sand-sized particles of glass. The disordered structure of this glass gives the material moderate hydraulic cementitious properties when very finely ground into granulated blast furnace slag, but if it can access free lime, the granulated blast furnace slag develops strong hydraulic cementitious properties. Pelletized or expanded slag is cooled through a water jet, which leads to rapid steam generation and the development of innumerable vesicles within the slag. The vesicular texture reduces the overall density of the slag and allows for good mechanical binding with hydraulic cement paste. Blast Furance Slag is a nonmetallic co-product which is produced in the process of iron manufacturing, Granulated Blast Furnace Slag is a glassy granular material formed when molten blast furnace slag is rapidly cooled by direct water. Rapid cooling prohibits the formation of crystals and forms glassy, non-metallic, silicates and alumino silicates of calcium. GBFS : (Granulated Blast Furnace Slag) Source : Granulated BF Slag From Gujarat State, India Supply Quantity : 50,000 Metric Tons Per Month Packing: Bulk Parameters (% BY MASS) CaO 30-38 Al2O3 15-20 SiO2 30-40 Glass Content 85-97 MgO 8-11 Fe2O3 0.5-1.5 Moisture 10 MAX Size -5mm Min 95, +5 mm Max 5 Relative Gravity 2.9 Bulk Density(Bagged) 1200 KG/M3
We Are A Prominent Organization Engaged In Offering A Wide Range Of Generator Parts, Electrical Goods, Lubricants Oil, Industrial Ancillaries, Construction Equipment Parts. These Products Are Highly Durable And Cater To The Requirements Of Diverse Industries.