The strength of the sack is its most important characteristic. It is what makes the sack stand out compared to other industrial sacks. The reason is the fabric, woven of polypropylene stretched tapes, which makes the sack resistant to dropping, pressing and bending. Even when handled with a hook or damaged on a nail the sack does not rip open and spill holds its contents. The special sack protects your goods from factory to end consumer The most important characteristic of packing units is the guarantee that the filling material will be kept as safe as possible from the factory to the end consumer. Strong cloth keeps the number of sacks broken or damaged during use to a minimum. Varying sack properties according to the specific filling goods - from airtight to highly air-permeable for filling or breathing of the goods - ensures perfect protection of your valuable packed material. No Spillage As a result, the sack survives even rough local handling conditions. Minimum sacks damage or breakage during filling, conveying, loading and transport. Water resistant Withstanding water and humidity, the sack keeps its full strength in all conditions - even when lying on damp ground, exposed to rain or to high air humidity. Made from water- resistant polypropylene, the sack is not affected by any form of moisture, unlike paper. This does not mean that sack is always completely watertight. In some applications the sack has to be produced with micro-perforations to give it the necessary air permeability. UV degradable The sack is made from polypropylene, which is broken down by UV when exposed to sun for a long time.
Temporary fence is also known as temporary fencing, temporary fence panels, portable fence, Temp fence, temp fencing and mobile fence. Description: Temporary fence panel and base composed of welded mesh panel or chain link mesh panel and tubes. The fence, the post and the hook will be welded together. Between every two pieces of the fence, we will install them with the steel clamp. Meet AS4687:2007 standard Materials: High quality mild steel wire and tube Corrosion Form: hot-dipped galvanized Fence heightxlength: 2.1x2.4m, 1.8x2.4m, etc Wire diameter: 3mm, 4mm, 5mm Welded mesh opening: 60x150mm, 50x75mm, 75x75mm, 60x75mm, etc Fence frame pipe OD: 32mm, 42mm, 48mm Clamp: suit for different frame pipe, 75mm/100mm center space Surface treatment: hot dipped galvanized Zinc coating: 42 microns Fence base: blow/injection molded base with concrete inside blow molded base size: 600x220x150mm injection molded base size: 560x245x130mm Extra brace: 1.8m height PE hoarding panel is also available, whtie/blue color Temporary fence production flow: Pre hot dip galvanized wire drawing, cut wire and pipes, wire welded, cut the corners of the mesh, Pre hot dip galvanized pipes welded, polish the welds, paint anti-rust epoxy, spray sliver powder coat on each welds, packaging Application: 1. Temporary fencing to secure construction sites and private property. 2. Temporary fencing of residential housing sites. 3 Temporary fencing for major public. Events, sports, concerts, festivals, gatherings etc. Features: It can quickly and easily be installed, without the need to disturb the surface area by digging holes or laying foundations.
Quick details Properties: other place of origin: hebei, china (mainland) brand name: shuci model number: yw-01h item name: back support color: black , beige size: l/m/s/xl/xxl/xxxl material: top grade spandex, self-heating fabric, magnet, aluminium strips, net weight: 0.37kg per piece certification: iso9001, 13485, ce, fda, sgs Packaging & delivery Packaging details:Pp bag with carton and then wrapped with scoth tape Product description Double pull lumbar brace pain relief self-heating back support Item name Back support Model Yw-01h Color Black , beige Size L/m/s/xl/xxl/xxxl Material Top grade spandex, self-heating fabric, magnet, aluminium strips Net weight 0.37kg per piece Oem/odm Welcome Sample Available Certification Iso9001, 13485, ce, fda, sgs Feature Highly supportive, adjustable elasticity, the infrared heating can achieve the magnet therapy, extremely effective, Convenient to wear Function To treat lumbar vertebrae hyperosteogeny, to cure the lumbar dis herniation and other lumbar injuries Details show 1.Top grade spandex, soft and comfortable. 2.Hook&loop, strong stickness. 3.Widening design. 4.Curved alloy strip. Fob price:Us $7.6 - 8 / piece | get latest price Min.Order quantity:200 piece/pieces Supply ability:10000 piece/pieces per day Port:Tianjin, china Payment terms:L/c, d/a, d/p, t/t, western union, moneygram
Specifications: Material: toray t700 full carbon type: clincher tubeless compatible & hookless Rim depth: 30mm external width: 33mm Internal width: 26mm brake system: disc brake Application: cross country(xc) weight: 430¡¡§¡è15g Erd: 579 bsd: 622 Spoke hole offset: 2.8mm spoke hole dia: 4.3mm Assembly hole dia.: 7.5mm valve hole dia.: 6.5mm Lead time: 5-15 days standard: en standard Why boths the offset rims: Solve the problems of a bike chain's side is weighter the other side.As we are know, mostly in the chain side is weight than another side..Offset rims.Can improve the chain-side weight.It can insure the rims weight center point is in the centeral.From the cyclists reviews used more smoothly and fastest than usually. Design characters: Ø hookless: by getting rid of the hook from the top of the rim sidewall, the rim wall became smooth and straight, it is easy to install a tire, and the tire and rim will work perfectly to create a seal. So riders are allowed to run lower tire pressure without the risk of air loss or pinch flats. Ø tubeless compatible: this allows to run tubeless perfectly, makes wheels superlight. Ø filled with 3d weave, that will make the rim stable, safe and durable. Ø these rims build up into stiffer, stronger and more reliable wheels by improving the bracing angles of a dished wheel and equalizing the spoke tension.
ALUMINYUM LUXURY PANEL DOOR The thickness of steel safe door parts 1,50 mm and door leaf 1,50 mm and DKP steel Steel doors safe over whether exterior moldings membrane coating is applied. Superficial 10 mm MDF outer wing part of the door is applied. Jamb door frame up with the same figure is coated with ribs. Box contents holders of key provisions found in box shaped box closed doors will not be affected by whether the mortar material. Secret amulet at the bottom to the rotation of the door moldings in the Box there are sheet. This amulet does not appear when the sheet wings open. In box and wing is double cord doors are suitable to wood color. Aluminium complete part surrounded by the door wings are lower then cord aluminum. Wing Inside will be two wooden between 1 mm monolithic welded DKP sheet Inside the wing is reinforced with cord, In the wings is Izocam ýsolation between two wood, Wings will be aluminum kick plate at the bottom. Box with a cross between jamb Inside chrome nickel employees hidden security clamp (304) will, When the side door 4 piece hard cover case safety pins whether this at the last slot of the safety pin plastic materials not will be printed Instead of the original molds of steel. Paint the door of steel section 220 degree baked electrostatic paint, Lock cylinder and steel is embedded in the wing portion Hooks, Lock the doors central system will be used. Property 3 units can be lubricated hinges hinge and this is the ball, Accessories; first class will be satin coated accessories (Interior Arm, 40 K arm. Steel badges, wide and large binocular cover, badge, number of health ) 210*105cm 80to100kg
Copper Wire for Cables and Filter Screens Copper Wire Raw materials: hot-rolled copper. Wire diameter: 0.25mm - 6mm. Tensile strength: ¡Ý315 Mpa. Types: solid copper wire, insulated copper wire, stranded copper wire, tinned copper wire, brass wire. Features: good electrical and thermal conductivity, high tensile strength, excellent ductility, etc. Applications: Widely used in mesh weaving, copper brush making, cables, filter screen. Used as communications wire, in telephone, TV, Internet, etc. Used in the chemical industry, medical instruments, building. Used for making crafts, decorations. Used in the ground electrical supplies. Our products can be made and packed by your specific requirements. There is a spool of copper wire with shiny surface. Copper wire is widely used in electron, chemistry, construction and daily life. A roll of solid copper wire on white background. A good conductor widely used in cables, ground electrical supplies, etc. There are three insulated copper wires on white background. Insulated copper wire is very suitable when insulation is needed. There is a stranded copper wire with white background. Stranded copper wire is fit for substations, uninsulated hook ups, jumpers. Three spools of tinned copper wires. Tinned copper wires have excellent corrosion resistance performance. Tinned Copper Wire Gauges: 12 - 40 gauge. Processing: plates a single or several twisted copper wires with a tin layer by electroplating or hot dip coating. Features: excellent corrosion resistance. Brass Wire Gauges: 10 - 22 gauge. Features: Contains 65% copper and 35% zinc. Non-magnetic, wear resistance, good ductility. Excellent abrasion resistant performance. Applications: Used in decoration and jewelry making. Used in the mesh weaving, crafts making, etc. Used in the machinery and appliances. There is a bracelet made of brass wire. Brass wire can be used in making bracelets, which are artistic and beautiful.
New LEICA GS15 GNSS RTK Base and Rover CS15 Includes: - 2X 771503 LEICA GS15 Performance Receiver - 2X 767805 LOP2 GLONASS Option - 4X 772806 GEB212 Battery - 1X 810855 CS15 Field Controller - 1X 767874 CBC01 Lemo Connector Module with Power Jack - 1X 767909 SmartWorx Viva License Key - 1X 767879 GHT62 Pole Holder Base Plate - 1X 767880 GHT63 Clamp Arrangement - 1X 752292 GLS30 GNSS Telescopic Pole - 1X 799187 GKL341 Multi-bay Battery Charger - 1X 767856 MSD1000 Industrial Grade SD Memory Card 1GB - 2X 781646 SLR5 Satelline M3 TR1 403-470 Mhz RX/TX Radio - RTK Receive & Transmit UHF Radio Module - 2X 667243 GAT2 435MHz-470MHz Antenna - 1X 785703 GKL32 Battery Charger - 2X 767790 GAD108 Arm to Mount External UHF/GSM Antenna to GS14/GS15 - 1X 770715 GRT247 Carrier - 1X 399244 GST05 Wooden Tripod - 1X 798181 GDF112-1 Tribrach with Optical Plummet - 1X 667244 GZS4-1 Height Hook - 1X 758469 GEV219 1.8m Power Cable Connects External Battery GEB171 - 1X 727367 GEB171 External Battery - 1X 767827 GVP641 Hard Container - 1X 6003686 1 year Viva GNSS (GS10/14/15/25) Basic CCP - 1X 6003680 1 year Viva GNSS (GS10/14/15/25+CS+SW) Basic CCP complete package
Specifications high performance countersunk ring magnet/sintered NdFeb magnet with great low prices -Superior resistance to high temperature - Competitive price -Fast Delivery Product Name: cuntersunk ring Neodymium Magnets/countersunk ring NdFeB Magnet/Strong countersunk ring Neodymium Magnets/Motor countersunk ring NdFeB Magnets/Permanent Magnets/Rare Earth Magnets Applications: Widely used in different applications, such as sensors, motors, rotors, wind turbines/wind generators, loudspeakers, magnetic hooks, magnetic holder, filters automobiles and so on. Material: NdFeB (Neodymium Iron Boron) Magnetic properties: High coercive force, the max operation temp is up to 200 degree centigrade or 380 curie temperature Shape: contersunk ring Size: According to customer's requirements. Tolerance in size: +/-0.1mm (also can be made as per client's requirements) Type of coating: Ni ,Zn ,gold ,epoxy ,Ni-Cu-Ni, etc. Grade: N35-N52,M35-M50,H35-H48,SH33-SH45,UH30-UH40,etc. Direction of Magnetisation: According to customer's requirements. Free of harmful substances according to ROHS Directive 2002/95/EC Exempt from registration according to REACH. Package size: According to customer's requirements. Custom made are acceptable. When you send enquiry, Pls Indicate the Outer radius, Inner radius, Height, Angle, the grade, the coating, the quantity of the magnet you required. We will send you our best offer for your reference. We are also very delighted to send you some samples for your testing if you need. According to customer's requirements.
Product Description 3" FR triple trim across back, around upper arms and leg cuffs Hook and loop adjustable throat latch Left chest radio pocket with utility strap Mic clip above radio pocket Right chest oversized utility pocket Lined and reinforced padded elbows and forearms Hook and loop adjustable cuff closures Heavy duty, two-way Aramid zipper front closure with hook and loop storm flap (Fly area no hook and loop for ease of access) Hook and loop adjustable take-up straps at waist Scissor pocket with straps over semi-bellowed cargo pockets on both thighs Two rear patch pockets with hook and loop flap closures Padded knees and shins 12" leg zipper with hook and loop adjustable straps at ankle Product Type: FR04 Hi Vis Flame Resistant Blue Wear Rough China Coal Mine Sanfor Safety Overall Workwear,Hivis Flame Retardant Mining Workwear Material: 88% Cotton 12% Nylon Fabric Type: 7oz Twill Feature: flame resistant flame retardant Decoration: Coal Mine Mining Color: Navy Size Charts Company Profile Xinxiang Zhuocheng Special Textile Co.,Ltd is a leading manufacturer specialized in developing and manufacturing special protective fabrics.Founded in 1998, Xinxiang Zhuocheng Special Textile Co., Ltd has experienced significant success and growth in the past years. We have been and always will be committed to manufacturing, developing and distributing the best protective fabrics and apparel. DROTEX fabrics have been verified by BTTG, SGS, TUV, ITS,UL,etc, meeting even superior to standards of ENISO11611, EN ISO 11612, EN ISO 14116, EN ISO 61482, EN ISO 20471, NFPA2112, ASTMF1506, NFPA70E, EN1149-1/3/5, EN13034, etc . Now DROTEX has been the appointed brand of renowned clothing manufacturer, oil gas industry, iron and steel companies, Fire Protection Associations and is quite popular in US, Australia, EU and countries in North and South Americas. Xinxiang Zhuocheng Special Textile Co.,Ltd responsibly do business adhering to concept of "Safe, Green, Healthy, Comfortable" and strictly following the rules of OEKO-TEX STANDARDS 100 and REACH. Aiming to provide "Better Protection For Global Wokers", DROTEX will continue to produce high quality products and give best protection for special environment workers. Our Advantages 18 years experience We have been and always will be committed to manufacturing, developing and distributing the best protective fabrics and apparel. Quality guarantee Our quality department will inspect in grey strictly before dying fabric ,after the goods is all finished,our warehouse will inspect the goods and do fabric inspect report ,at last ,our QC will inspect fabric 20% to 30% of total bulk as the third party again.
1. Summarize 1.1. DYQ4 series liquid resistor starter (for short starter as follow) is a new starter prepared for improving the starting property of high voltage squirrel-cage alternating current asynchronously motor. It can induce the impact which is brought to motor starting current on power system, and improve the start smoothness with equipment by voltage-reduced starting by way of liquid resistance. It can protect the motor avoid harm by over-load, phase failure, short circuit etc.It is the prefect starting production instead of auto-induction voltage-reduced starter. 1.2. Model explanation 2. Working principles: The device is composed of resistor, high-voltage soft start controller, isolating cabinet, changeover cabinet and star point controller. We supply in full sets. The device can start motor and play a protected action on motor start process, when connect it in motor start circuit. This resistor is composed of three phase balancing resistor which have negative temperature characteristic, when the current is past through resistor, the temperature of resistor gradually increase and its resistance gradually decrease, then the terminal voltage of motor gradually raise and the start torque gradually increase, so the motor can start smoothly and the start current can be decreased. 3. Application scope: DYQ4 series high-voltage resistance soft starter is suitable for large and medium high-voltage squirrel-cage asynchronous motor or asynchronously-started synchronous motor, to voltage-reduced starting. The motor which start by this device have soft start characters like withlow and constant starting current, torque increased gradually etc. In start process, without current and mechanical shock, as well as have little impact on power system, and without electromagnetic interference. It is the prefect production instead of starting reactor auto-induction voltage-reduced starter. And compare with high-voltage inverter soft starter, DYQ4 have many evident advantages: simple operation, withoutmaintenance and no pollution of harmonic wave etc. 4. Advantage: 4.1. constant current, soft start: the starting current is 2.5-3.5 times as motor rated running current, avoid generating more heat while motor starting, can reduce the demand of transformer capacity with motor heavy load start, reduce no-recurring investment 4.2. The wave of the power system voltage and load cant influence the start process, it can start successfully at one time. 4.3. smooth starting, without shock to machinery, can prolong the service life about 30% of machinery and motor. 4.4. have large thermal capacity, and the continual starting attempt can reach 3-5 times 4.5. have little impact on power system, have small voltage drop during starting 4.6. have high power factor during starting 4.7. without harmonic wave pollution 4.8.start with static changeable resistor,safety and reliability 4.9. simple operation, maintenance free DYQ4 with standard design, have the advantage of low and constant starting current , have small voltage drop and big power factor during starting, without pollution of harmonic wave and simple, simple, safety and reliability etc. 5. Technical parameters Model Motor powerKW Rated voltageKV Rated start currentA style DYQ4-630 500-630 3 6,10 Integrated style DYQ4-1000 800-1000 3,6,10 DYQ4-1250 1000-1250 3,6,10 DYQ4-1600 1250-1600 3,6,10 DYQ4-2000 1600-2000 3,6,10. Split style DYQ4-2500 2000-2500 3,6,10 DYQ4-3200 2500-3200 3,6,10 DYQ4-4000 3200-4000 3,6,10 DYQ4-5000 4000-5000 3,6,10 DYQ4-6000 5000-6000 3,6,10 DYQ4-8000 6000-8000 3,6,10 DYQ4-12000 8000-12000 3,6,10 DYQ4-15000 12000-15000 3,6,10 DYQ4-18000 15000-18000 3,6,10 6. Working condition (1). The power source must use three-phase four-wire system of 380/220V/20A, and the wave of voltage mustnt exceed ¡¾15% of rated voltage. (2). temperature: from -5celsius degree to 60 celsius degree (the average temperatureless or equal55celsius degree within 24h) (3). relative humidityless or equal90% (4). elevationless or equal2000m (5). The installed site mustnt have obvious impact of vibration and the gradient of uprightness mustnt exceed 5 (6). conducting dust and corroding air are not allowed (7). without threaten by fire and explosion PS: A heater is needed when the temperature less than -5 celsius degree in a long period, this situation should be marked up when you order. If the elevation exceeds 2000m, please let us know when you order. 7. Outline size The starter has a cabinet framework, protection level is IP20. The outline size of unitary structure devices are as follow table Model Outline size mm Installation size mm A B C E F ©ªd DYQ4-630 1400 1200 2300 1240 1040 16 DYQ4-1000 1630 1230 2200 1540 1140 16 DYQ4-1250 1800 1230 2300 1640 1040 16 DYQ4-1600 1800 1230 2300 1640 1040 16 DYQ4-2000 1830 1230 2300 1840 1040 16 DYQ4-2500 2030 1230 2300 1840 1040 16 DYQ4-3200 2730 1230 2300 1840 1040 16 DYQ4-4000 2730 1230 2300 3400 1040 18 DYQ4-5000 2730 1230 2300 3400 1040 18 DYQ4-6000 3900 1600 2300 3400 1240 18 DYQ4-8000 4200 1600 2500 3400 1440 18 DYQ4-12000 4800 1800 2500 4600 1640 18 DYQ4-15000 5100 2000 2500 4900 1840 18 DYQ4-18000 5100 2000 2500 4900 1840 18 8. Transit and hoisting 8.1. According the customers demand, the pack can use simple packing, common packing and exported packing 8.2. Lie down the resistor during transit is forbidden, because it can damage the driving medium and insulated box (the hoisting method please according to picture 1). 8.3. The collision must be avoided when hoisting the single cabinet, and the hoisting must according the storage and transportation mark 8.4. Check the condition of packing before opening, if it was damaged seriously, please negotiate with traffic company or contact with us. 8.5. the steel wire should be used to hook in the diagonal rings when lifting. picture 2 8.6. The gradient must exceed 70o during hoisting. 9. Installation condition 9.1. The liquid resistor should be installed on the cement platform in which the water can easily drain 9.2. A horizontal ground is needed for installing, and the cabinet must perpendicular to it. 9.3. The liquid resistor should be installed right above the cable channel, and steel channel base must be matched with the resistor. 9.4. 3,2.5+1,1.5mm2 cable is used for control power supply, and connect it from A,B,C,N of terminal board X1 to starter, then according to the drawing, connect the liquid starter and control cabinet, and the interlock control wires between DCS systems or other central control systems 9.5 connect the green and yellow grounding lines to ground terminal. 10. Use and maintenance: 10.1. Check the condition of resistor before each start 10.2. Test the insulation resistance between ground regularly, the test result must less than 500M¥Ø using tramegger with the range of 1000V 10.3. Add water for the resistor regularly. 11. Ordering instruction: 11.1. the motors model, power, voltage, current, locked-rotor current, rotation rate, the times of start torque, the maximum times of start torque, the kind of motor and load GD2, the minimum capacity of short circuit for generatrix, the variation curve of load resisting moment, the name of matching equipment and the demand of duty type 11.2. the main circuits plan of high voltage starting for the using motor,the arrangement diagram of cabinet combination, and the layout chart of power distribution room 11.3. the surface color of cabinet 11.4. If the installation site has a special geographical condition like sea level elevation exceed 2000m, the environment temperature often blow 0celsius degree, coastal area and salt spray area, please let us know the situation in advance. 11.5. If you have special demand, please contact with us (one starter control two or more electromotor). 1500*1350*2000mm 1550*1460*2650mm.
4-Light Pot Hanging Rack Chandelier Size: Chandelier: 9.8 inches high, 11.8 inches wide and 34.6 inches long. Chain: 39 inches high(max). Canopy: 4.7 inches wide and 11.8 inches long. Total hanging weight for all hooks is 30 lbs at max. Easy Installation: Assembly required and easy to install, with all mounting hardware and a detailed mounting instruction included. Color: Black. The metal pot rack chandelier with black finish gives your kitchen island and dining room a country feel and adds much light for industrial , cottage, or farmhouse homes. It comes with 8 hooks for hanging pots and pans.
Performance characteristics of ultra-high power graphite electrode in 400 arc furnace Our products are characterized by high strength, good electrical conductivity, good thermal shock resistance and low consumption, and are widely used in metallurgical, chemical and mechanical industries. 50 % of the products are sold well in 30 provinces, cities and autonomous regions in China, and 50 % are exported to more than 30 countries and regions including Southeast Asia, Japan and South Korea, Europe, the Americas, and Africa. Technical parameters of ultra-high power graphite electrode in 400arc furnace Specification for the Use of Ultra-High Power Graphite Electrodes in 400 Electric Arc Furnace Points to note for the use of graphite electrodes: 1, wet graphite electrode, dry before use. 2, remove the foam protective cap on the spare graphite electrode hole, check whether the inner thread of the electrode hole is complete. 3, clean up spare graphite electrode surface and hole thread with compressed air without oil and water; Avoid cleaning sand cloth with steel or metal brushes. 4, carefully rotating the connector into the electrode hole at one end of the backup graphite electrode(it is not recommended to load the connector directly into the electrode removed from the furnace), not to collide threads. 5, the electrode hanging equipment(recommended graphite hanging equipment) into the electrode hole at the other end of the backup electrode. 6, when lifting the electrode, loosen the soft material to the bottom of the end of the standby electrode connector to prevent the ground from hitting the connector; Lift the pendant ring with a hook, and the lifting electrode must be stable to prevent the electrode from loosening from the B end or colliding with other fixing devices. 7, hanging the spare electrode to the top of the electrode to be connected, pointing at the electrode hole and slowly falling; Rotate the backup electrode so that the spiral hook rotates with the electrode to drop; When the two electric extremes are 10-20mm apart, the exposed parts of the two ends and joints of the electrode are cleaned again with compressed air; When the electrode is finally completely decentralized, it must not be too violent. Otherwise, due to violent collisions, the electrode holes and joints will be damaged.
Shaker screens including but not limited to the following types: 1. Steel Frame Shake Screen 2. Composite Frame Shaker Screen 3. Pyramid Shaker Screen 4. Hook Strip Flat Screen 5. Hook Strip Soft Screen We provides all the API series screens from API 20 to API 400. Our shale shaker screens are available for the FLC Series. Brandt VSM, Cobra Series, Mi-Swaco, Derrick, NOV Brant, Swaco Mongoose and KEM-TRON shale shakers, and we accept customized shale shaker screen. FAQ How can I place order? A: You can contact us by email about your order details, or place order on line. How can I pay you? A: After you confirm our PI, we will request you to pay. T/T (HSBC bank), Western Union are the most usual ways we are using. Whatâ??s the order procedure? A: First we discuss order details, production details by email or TM. Then we issue you an PI for your confirmation. You will be requested to do pr -epaid full payment or deposit before we go into production. After we get the deposit, we start to process the order. We usually need 7-15days if we donâ??t have the items in stock. Before production has been finished, we will contact you for shipment details, and the balance payment. After payment has been settled, we start to prepare the shipment for you. How do you take care when your clients received defective products? A: replacement. If there are some defective items, we usually credit to our customer or replace in next shipment.
Shaker screens including but not limited to the following types: 1. Steel Frame Shake Screen 2. Composite Frame Shaker Screen 3. Pyramid Shaker Screen 4. Hook Strip Flat Screen 5. Hook Strip Soft Screen We provides all the API series screens from API 20 to API 400. Our shale shaker screens are available for the FLC Series. Brandt VSM, Cobra Series, Mi-Swaco, Derrick, NOV Brant, Swaco Mongoose and KEM-TRON shale shakers, and we accept customized shale shaker screen. FAQ How can I place order? A: You can contact us by email about your order details, or place order on line. How can I pay you? A: After you confirm our PI, we will request you to pay. T/T (HSBC bank), Western Union are the most usual ways we are using. Whatâ??s the order procedure? A: First we discuss order details, production details by email or TM. Then we issue you an PI for your confirmation. You will be requested to do pr -epaid full payment or deposit before we go into production. After we get the deposit, we start to process the order. We usually need 7-15days if we donâ??t have the items in stock. Before production has been finished, we will contact you for shipment details, and the balance payment. After payment has been settled, we start to prepare the shipment for you. How do you take care when your clients received defective products? A: replacement. If there are some defective items, we usually credit to our customer or replace in next shipment.
Shaker screens including but not limited to the following types: 1. Steel Frame Shake Screen 2. Composite Frame Shaker Screen 3. Pyramid Shaker Screen 4. Hook Strip Flat Screen 5. Hook Strip Soft Screen We provides all the API series screens from API 20 to API 400. Our shale shaker screens are available for the FLC Series. Brandt VSM, Cobra Series, Mi-Swaco, Derrick, NOV Brant, Swaco Mongoose and KEM-TRON shale shakers, and we accept customized shale shaker screen. FAQ How can I place order? A: You can contact us by email about your order details, or place order on line. How can I pay you? A: After you confirm our PI, we will request you to pay. T/T (HSBC bank), Western Union are the most usual ways we are using. Whatâ??s the order procedure? A: First we discuss order details, production details by email or TM. Then we issue you an PI for your confirmation. You will be requested to do pr -epaid full payment or deposit before we go into production. After we get the deposit, we start to process the order. We usually need 7-15days if we donâ??t have the items in stock. Before production has been finished, we will contact you for shipment details, and the balance payment. After payment has been settled, we start to prepare the shipment for you. How do you take care when your clients received defective products? A: replacement. If there are some defective items, we usually credit to our customer or replace in next shipment. How to contact with us:
Galvanized Metal Planks Material:Q195 or Q235 Surface treatment:Pre-galvanized Color:Silver Length:1000-4000mm or as your request Width:210-500mm Thickness:1.0-2.0mm Height:38mm, 45mm, 50mm, 60mm, 76mm Hook:43mm,50mm Emboss:Available Packaging Details:Packed with steel strips, steel pallet, film or as customer's requst Application:Outdoor Building Construction Delivery Detail: Advantages Galvanized Metal Planks is YXSY one of the most important products. Excellent quality and competitive price,OEM is highly welcomed. 1.Scaffolding plank is the main parts of scaffolding system which is convenient for workers to walk on high building. 2.Stamping holes are on the scaffolding plank to resist skidding for workers. 3.The galvanized surface and  rib reinforcement design makes scaffolding plank more stronger in the rainy days and moist environment. 4.Secondary resources recovery. 5.Various size of scaffolding steel plank could be customized. Product Description 1. Scaffolding steel plank is compatible with various types of scaffolding system,fastened scaffolding ledger with 2 hooks on each end. 2. Scaffolding steel plank allows easy and safe access for people to walk through scaffolding standards and ledgers. 3. The surface of steel scaffolding plank can be hot dip galvanized or zinc plated for long-lasting use. 4. To prevent slip,the steel plank surface has many punched holes and allow water to drain through. 5. The steel plank assure high durability due to reinforced cross members at the back side and convex tread surface. 6. Galvanized Metal Planks is designed to be light-weight,safe and durable,suitable for a work-platform at a high place.Since it is 10% lighter than the conventional plywood board,steel plank is highly recommended to be used at construction site. Galvanized Metal Planks, Scaffolding steel plank Manufacturer
Snuff bottle is a kind of traditional handicraft, which began in the Ming Dynasty and flourished in the Qing Dynasty. The inner painted snuff bottle appeared in the early days of Daoguang at the end of Jiaqing. It is painted in a transparent pot with a special tiny hook brush. The original interior snuff bottle was a transparent glass pot with no frosted inner wall. Because the inner wall was smooth and not easy to attach ink and color, it could only draw some simple pictures and patterns, such as: Des sauterelles cabbage, dragon, phoenix and the stick of landscapes, figures, etc., then, artists use iron ore and emery water back and forth in the snuff bottle inside roll grinding, such making that the snuff bottle inside white frosted glass, is exquisite and smooth, easy adherent inky, effect like rice paper, painting of snuff bottles later some more fine works, Later developed for poetry, calligraphy and painting together with fine art. After snuff was introduced into China, the Chinese people first used traditional medicine bottles to hold snuff. On this basis, they used a variety of materials and production techniques to perfect the container of snuff. In the process of use, they found that the bottle with a small mouth and large stomach is more beneficial for storing snuff, which can ensure that snuff does not go bad in long-term use, and is convenient to carry, with the traditional Chinese aesthetic style, so it is loved by snuff smokers. In China's Qing Dynasty, from the emperor to the people, inhaling snuff is very popular. Led by the emperor of the feudal nobility, extravagant, they use snuff bottles often collect precious materials, skilled craftsmen for their design, manufacture. Some collectors think in the world, snuff bottle is a collection of Chinese arts and crafts into the pocket art. Material editing broadcast Carved lacquer snuff bottle past life Carved lacquer snuff bottle past life Inner Mongolia to silver and other metal craft snuff bottles; Liaoning is rich in agate, mainly in agate snuff bottles; Xizang is also based on metal snuff bottles. Snuff bottles can be made of many materials, including gold, copper, silver, porcelain, materials, jade, coral, agate, amber, jade, crystal, wood, bamboo root, wood stone, lacquer, gourd, fruit stone and so on. Figure tattoo snuff bottle Chinese snuff bottle is a collection of Chinese painting, calligraphy, carving, insetting and jade, porcelain, material, lacquer, enamel, metal and other crafts in one. Production editor
The Wire Forming Machine builds complex shape springs. The advanced and the higher version of the CNC bending machine and spring coiling machine is wire forming machines. The machine comprises 4 models. Hence, 3 axis CNC wire forming machine is one of the basic models of a CNC wire forming machine. As a CNC Wire forming machines manufacturer, Auto Link produces the Machines as per the custom standards. Hence, the requirement for the machine is high. Similar to that of Wire bending & spring coiling machines, the spring forming machine works. The wire forming machine produces complex shapes of compression, torsion, extension, and tower springs. Input Materials: Stainless Steel, Aluminium, Brass, Bronze, Carbon Steel, Cold-Rolled Steel, Copper, Nickel, Titanium, etc. The input wire diameter ranges between 0.3mm and 3.5mm. The decoiler sends the input metal or wire to the straightening unit and a wire feeder roller. It straightens the wire precisely. Then the free-hand arms help to produce the output wire or spring forms. The feeder gives the wire through the quilling axis. Then the bending tools encounter the defined shape to meet the industrial needs. The user can attach only a few numbers of tools with the machine according to the requirement. It also comprises of holding tool if necessary and a metal softening tool. Then, the machineâ??s design is of cam basis, which is having 1 motor with 8 arms. Therefore, it reduces the efficiency of the machine. Thereby increases the manual work. Features of 3/4Axis CNC Wire Forming Machines: The machine comprises an imported Wire Feed Bearings. Equipped with High-Strength Transmission Belt (German Technology) Special Design of Zero-Degree Gear The servo motor and CNC programming units are the main units of thespring-forming CNC machines. The Auto Link makes use of a Japanese Servo motor for ensuring better performance. Hence, the control unit controls the overall operation of the machine. Industrial and Commercial Applications: The wire or spring forming machines are used for many industrial and commercial applications. Auto Link is then enhancing the business at a higher rate via Alibaba & Made in China. Paper clips Bookshelf Hand gripper spring Stainless Steel Double Glide Hooks Candleholders Available Models:WF-20 & WF-35
The 4000-Lb. 12 Volt DC ATV Winch is an intermediate-duty ATV winch meets the rugged demands of ATV and utility use while providing an excellent value. The LT4000ATV combines a strong fabricated steel drum, powerful permanent magnet motor and strong 50ft. wire rope. What's Included (1) LT4000 ATV winch with wire rope (1) Rocker switch (1) 12ft. handheld remote (1) Roller fairlead (1) Roller fairlead mount plate (1) Mounting bolts and washer kit Features + Benefits 4000-lb. pulling capacity (single line) 12V DC, 1.4 HP low amp permanent magnetic motor 50ft. x 3/16in. steel wire rope w/hook 4.5 FPM full load speed drawing 210 Amps 18 FPM no-load speed drawing 20 Amps Handlebar rocker switch and 12-ft. handheld remote Heavy-duty 4-way roller fairlead Powers load in and out Cut steel 3-stage planetary geartrain Mechanical and dynamic braking Automatic 100% load holding brake minimizes wire rope slippage during power failure and provides quick stopping of drum Freespooling clutch with ergonomic control Reinforced steel drum Sealed solenoid and circuit breaker protection ensure safe, reliable electromagnetic power in all weather conditions Key Specs Item# 46717 Brand Superwinch Manufacturer's Warranty 1 year Limited Warranty Ship Weight 30.0 lbs Volts 12 HP 1.4 Line Pull (lbs.) 4,000 Line Speed (FPM) 18 no-load; 4 1/2 full load Gear Train 3-stage planetary Gear Ratio 166:1 Clutch Cam action for freespooling Braking Mechanical, dynamic Switching Method Handlebar-mounted toggle, handheld remote Remote Length (ft.) 12 Rope Type Steel wire Rope Size L x dia. (ft. x in.) 50 x 3/16 Fairlead Type 4-way roller Battery Leads 8 ft. x 6 gauge Mounting Hardware Included Yes Mounting Bolt Pattern L x W (in.) 4.87 x 3 Dimensions L x W x H (in.) 13 1/5 x 4 1/2 x 4 1/2
Deltic The Rising STAR STAR E-Rickshaw is miles ahead in the race with a 25% higher mileage than any other E-Rickshaw in the country. The cutting edge technology used, packs power in our E-Rickshaw to cover 125 kms in a single charge. 1. Our vehicles are designed completely on a 60V platform and provide a mileage of 125 kms on a single charge. 2. Higher torque 6800 rpm motor compared to 3100 rpm of conventional motors for better pickup and climbing gradients. Even if you overload the vehicle with passengers, the vehicle can easily climb flyovers 3. Extra Earning potential for the drivers to the tune of INR 1,08,000/- on a yearly basis on account of higher mileage: a. Minimum extra mileage per day due to extra battery 30 km b. Average earning per km Rs. 10 c. Extra earning per day due to one extra battery Rs. 300 d. Extra earning per month due to one extra battery Rs.9,000 e. Extra earning per year due to one extra battery Rs. 1,08,000 4. This extra earning can be easily utilized to pay off monthly Bank EMI's. 5. Enhanced battery life of 9-10 months compared to 6-7 months of other rickshaw. 6. About us a. Legacy of a 300mn dollar, 100 year old BMA group- & empire of multiple flagship industries across 5 verticals. b. Total group turnover of more than 3000 crores. c. Many more upcoming products and a vision of a range of products under the â??Deltic Greenâ?? vertical having products like Electric Scooters, Electric Loaders, High speed Electric Auto etc. 7. Designing a. Ergonomically designed to provide better seating space; passenger knees donâ??t get locked with each other. b. Better seating comfort because of our specially designed cushioned seats c. Essentials on-the- go like mobile charger, mobile holder, bottle holder, grocery hook and personal storage compartment. 8. Safety a. Conveniently located hand brake for better control in emergencies. b. Handle lock for protecting against theft c. Cold Rolled Steel bumper to absorb high impact collision d. Tyres and axle designed for max load+30% factor of safety e. Metal guard on the front panel for superior safety 9. Quality a. ABS Roof and Stepaney Cover b. High quality armrest and hand holders c. Solid Metal Guards for protecting tail lights, headlamps, etc. d. 10mm thick water proof wiring.
