Digital Rail Head Wear Gauge is is mainly used to measure the vertical wear and lateral wear of the rail. The reasonable design makes it light, convenient operation and intuitive reading. FEATURE 1. Digital type with direct readings: LCD display screen, clear and readable; No calculations required, gives direct reading ; When reading, hold down the HOLD button to fix the measurement value and facilitate reading. 2. High measuring accuracy : The measurement accuracy is 0.01m 3. Easy to use, measure the vertical and lateral rail wear at the same time, Position the rail wear gauge on the outer side of the rail . Push the vertical and lateral rail wear gauge so that the measuring probe is in contact with the upper surface and inner side of the rail respectively. Then the vertical and lateral wear of the rail can be read. 4. Metric /imperial unit 5. Support customize: We could customize all kinds wear gauge according to different rail profiles and different measure points. 6.Fast calibrate: One-key zero clearing function, can be quickly calibrated before each use to reach the factory measurement accuracy. 7. Magnetic fixed part: Strong magnetic fixed part to attach to the rail. 8. Rail fillet as measuring base to ensure measure data more accuracy Rail fillet is more clear than rail bottom, no dust. It could ensure the measure result reliability. 9. Portable Handle : This product is designed with a handle that is easy to hold, which greatly improves the portability of the product. It can avoid touching the ruler body directly, cause the ruler body to be stained and corroded, improve the product service life. Model LJ-GM-A Center vertical wear measure range0-15mm Lateral wear measure range0-25mm Score value0.1mm Indication error ± 0. 15mm Supply CustomizeUIC60/60E1, UIC54 /54E1, 115RE 68TR ect all profiles Block customize block for gauge
21.5 Inch 1920x1080 FHD 30PIN LVDS-Double IPS 600nits Open Frame LCD EX21501-A01 is a 21.5 inch 19201080 Resolution IPS TFT LCD module that supports LVDS interface. It can be operating at temperatures from 0~50 and storage temperatures range from -20~65. And, it features with 600(nits) high brightness and wider viewing angle technology. Open frame tft display is Suitable for industrial and medical imaging self-service terminals retail terminals supermarket checkout machines,etc. General Specifications of� 21.5 Inch 1920x1080 FHD 30PIN LVDS-Double IPS 600nits Open Frame RGB vertical stripe No. Item Specification 1 LCD size 21.5 INCH 2 Resolution 19201080 3 Active area 476.64(H)268.11(V)mm 4 Module size 487.54(H)279.684V1.335Dmm 5 Interface LVDS-Double 6 Brightness 600cd/m2 7 Contrast Ratio 4000:1 8 Pixel arrangement 9 Surface Treatment Anti-Glare� 10 Display Colors 16.7M 11 Polarizer Transmissive 12 Display mode Normally Black As a professional tft module factory, we provide tft lcd display module, ips tft capacitive touchscreen, ips capacitive, ips capacitive screen, ips lcd capacitive, ips touch panel, ips capacitive touchscreen, ips lcd touch screen, ips lcd capacitive touchscreen, china tft lcd display, etc. For more information, please feel free to contact us!
PRODUCT DESCRIPTION High Durable Excavator Thumb Bucket Hydraulic Grab Bucket Hydraulic Thumb Bucket Description Also Known as Thumb Bucket, Clamp Bucket, It Mainly Applies for Recycling / Civil Applications. Clamp Bucket Specification Weight kg 180 360 520 840 1430 1860 Max Opening mm 818 1150 1380 1550 2220 2235 Oil Pressure kg/m^2 100-130 110-140 120-160 150-170 160-180 160-180 Operating Oil L/min 25-40 30-55 50-100 90-110 100-140 130-170 Cylinder Volume ton 4 5.4 5.4 8.2 10 12 Suitable Excavator ton 2~3 4~6 7~11 12~16 17~23 24~30 * The Parameter above may change with the technology improvement, will not notice additionally, please understand. * For other diameters and lengths, we can customize service, OEM/ODM Thumb Bucket Features 1. Rotary Type High Durable Q345B Steel Excavator Buckets Toosan Digger Hydraulic Thumb 0 2. Fixed Type: High Durable Q345B Steel Excavator Buckets Toosan Digger Hydraulic Thumb 1 Clamp Bucket Real Work shot High Durable Q345B Steel Excavator Buckets Toosan Digger Hydraulic Thumb 2 Excavator Integrated Thumb Bucket Can be used for disposable waste, shrubs, logs, construction waste, stones, pipes, landscaping materials, and demolition sites.Hydraulic excavator grab disassembly and recovery/civil applications. The thumb bucket has advantages in grasping small pieces of wood, sticks, and strips. Suitable for municipal construction, secondary demolition, mining, and most of the operating environment. Easily handle all types of loose, irregularly shaped objects encountered in demolition, industrial, construction, recycling, storm debris removal, landscaping, and other tough job applications.
Plasma cutting machines are used for iron/steel plate cutting, if you have big size metal to cut, the portable and table type are all not suitable. You need choose gantry type plasma cutting machines, but it price is very high. So we design this kind plasma cutting machines that can cut big size iron/steel plate with good price. Features of plasma cutting machines: 1 .The machine is all welded as seamless steel structure. Steady structure and long life time 2. High configuration, high cutting speed and precision. 3., Auto ARC starting. Steady performance. 4, Control system: STARFIRE control, with USB interface 5. Cutting material: steel, copper, iron, aluminum, galvanized sheet, titanium plates, and so on. 6. File format: G-code 7, Suitable Software: CAD, ART CUT, Type, Art CAM etc Parameters of plasma cutting machines Working Voltage 3-Phase 380V/2-phrase 220V Working Area(X*Y) 2000*3000mm, 2000*4000mm, 2000*5000mm, 2000*6000mm Machine Structure Welded X Y Guide Rail Taiwan HIWIN Square Rail X Y Transmission Imported Rack gears Drive Mode Stepper Motor (Optional Servo ) Control System STARFIRE Max thickness 30mm Plasma Generator 63A/100A /120A/160A/200A Cutting Speed 0-10000mm/min G.W. 1500KGS
RB 1530 portable CNC plasma flame cutting machine has two working modes: plasma cutting, and (flame) gas cutting. Usually plasma cutting machines are used for thickness less than 30mm metal cutting. The gas (flame) cutting machines are used for thickness 30-200mm iron/ steel cutting. Portable CNC plasma flame cutting machine features 1. Two cutting modes optional: plasma cutting and gas (flame) cutting. 2. This CNC plasma cutting machine moves by high precision gear and rack ,accurate running in high speed. 3. The operation is simple, fast, easy to learn the programming software. 4. Small cutting loss and typesetting software high material utilization. 5. Read U disk files through USB directly, convenient site operation. 6. The machine also has feature that automatic arc voltage torch height control, it can adjust cutting distance automatically. 7. It is easy to move, suitable for the site indoor or outdoor 8. Can automatically memorize and restore when power is off. Portable CNC plasma flame cutting machine parameters: Model RB-1530 Working Voltage AC 220V/380V, 50HZ Cutting Size 1500mm*3000mm Plasma Cutting Thickness 0-30mm,According to different power source Gas(flame) cutting Thickness 1-200mm Weight 230KGS Control System STARFIRE(FANGLING optional) Driving System LEADSHINE stepper motor Transmission Method Gear transmission Power Supplier HUAYUAN power or US HYPERTHERM Guide Rail Round rails Nesting Software FASTCAM
Product Descriptions: This full-automatic quantitative vacuum sausage stuffer is filled by vane pump, driven by servo motor, operated by human-machine interface, and equipped with twisting and kinking structure, and its automatic motions are controlled by micro-computer. This machine is able to fill casing products like sausage, ham sausage, ham and etc. and to quantitative twist and kink those products which are wrapped by natural casings, collagen casings and fibrous casings. As well, this machine can fill boxed, bottled or canned product. The automatic blade compensation device in the machine can achieve the quantitative accuracy to �±3mm, and deliver material delicately. And the speed of filling, twisting and kinking, the number of twisting, weight of every segment can be adjusted. The filling process of this machine is under vacuum environment. The hopper could be flipped, which is easier to wash and clean. This machine is manufactured of stainless steel, and essential parts are treated specially, thus they are hard-wearing. And the controlling parts are imported; appearance is treated by advanced surface treatment technology. Those advantages make the machine reasonable structured, convenient to operate, easy to maintain. And at the end, with not mentioned security devices, this is an ideal equipment for meat processing industry. Main Features: 1. Simple structure in linear type ,easy in installation and maintenance. 2. Adopting advanced world famous brand components in pneumatic parts ,electric parts and operation parts. 3. High pressure double crank to control the die opening and closing. 4. Running in a high automatization and intellectualization,no pollution 5. Apply a linker to connect with the air conveyor ,which can directly online with other machine Technical Specification: Model BG-6000 Power 8kw, 380v/50hz/3 phases Filling Capacity 6000kg/h (100r/min) Quantitative accuracy �±2g Hopper volume 200L Kink speed 0-500times/min Quantitative Range 6~9999g Center height 980~1030mm(adjustable) Maximum vacuum degree -0.1Mpa Machine Weight 550kg Dimensions 1980x1125x1780mm
Place of Origin: China Classification: Laboratory Centrifuge Brand Name:OEM Model Number: V-GTM12 Max. Speed: 12000rpm Max. RCF:15800xg Max. Capacity:24pcs Capillary*75mm Time Range: 0~99min59s RPM/RCF Convert:Yes Noise (dB)â?¤ 55 Temperature Normal Acc/Dec:10 Kinds Speed Accuracy: �±20r/min Voltage(V/Hz):AC 220V/110V 50HZ/60HZ High speed micro 24capillary hematocrit blood separation lab centrifuge Micro Hematocrit Centrifuge 1.Frame is 3 tiers protection steel jacket, and with the stainless steel chamber, inside protective steel lagging which is simple-compact,light-weight and low noise. 2.Adopt advanced CPU control system realizing microprocessor control, it can control rotate speed, and relative RCF, LCD display which indicates the current speed, time and RCF. 3. Brushless inverter motor with simpler construction,more reliable performance,longer life and quietly running. 4.With many kinds of rotor for your choice. 5.Over speed and imbalance protection, the centrifuge will stop automatically when the above situation happened, with short spin function. 6.Emergency locks under the bottom of the centrifuge which help you open the lid when power off. 7. It is consistent with CE security certification and ISO9001 quality certification. Company Profile
Features: 1) Beautiful The remote control robot chassis is beautiful in appearance. The fuselage is large, and the space reserved for development is sufficient. 2) Strong The bottom of the fuselage is reinforced to carry heavy loads. The installation position of the travel motor has also been reinforced to prevent deformation and displacement. The tires are lawn tires with a width of 15cm, which are beautiful, durable, large in width and strong in support. 3) Mature technology This product is modified on the basis of our very mature remote control lawn mower, an economical chassis product. It adopts the mature walking motor controller on our remote control lawn mower, which has the characteristics of sensitive response and fast response speed. The built-in smart chip can intelligently detect the current and heating conditions, which can ensure stable use all year round. And it has a slow start function, the operation is smooth, and there will be no frustration when accelerating or decelerating suddenly. 4) Scalability Equipped with a function expansion HUB, which can control additional 4 channels, it can easily control and expand other functions required by customers without professional remote control knowledge. On the basis of our chassis, you can freely add other functional modules to create a new vehicle that meets your own needs. Specification: Walking Speed: 0-6km/h Working Temperature: -20~55�° Remote Control Range: 200m Walking Motor Motor Type: Brush electric traction Voltage / Power: 24V / 350W Reduction Ratioï¼?23.2:1 Rotating Speed: 75RPM Rated/Max Output Torque: 18.4/55Nm Wheel: 15X6.00-6 vacuum tire Battery: 24V 20Ah Remote Control Channel: 7 Extended Controllable Channel: 4 Payload: 50~300kg Wheelbase: 810mm Track: 890mm Overlay Panel: 990*625mm Machine Size: 1070*1035*430mm Machine Weight: 98kg Package Size: 1150*1120*600mm Gross Weight: 130kg
Do you want to spend less time aerating and more time enjoying your lawn? The BlueBird TA10 has a wide width of 36" to let you aerate more land in less time. Two independent tine rotors which have 32 interchangeable closed spoon tines give you an aerating width of 36 which allows you to aerate large areas quickly. Optional weight containers can be purchased to add extra weight for optimal soil penetration. Maneuver around tight areas and corners with ease thanks to the dual tine rotors. Plus the unique side wheel system also adds to the maneuverability by allowing the aerator to move through tight passages and also allows it to be stored on its side. Tow Behind Aerator:No engine to worry about! Just be sure to use a tractor with an engine that is 16HP or larger to tow this aerator. Wide Aerating Width:36 of aerating width allows you to cover large areas in less time Adjustable Aerating Depth:Aerate from 0-3 for precise and consistent coring 40 Interchangeable Closed Spoon Tines:4.4 x 6 tine pattern Unique Side Wheel System:Allows aerator to easily move through tight passages without getting hung up and also allows for the aerator to be safely stored on its side. Optional Weight Containers (Sold Separately):Add up to 5 weight containers to add additional weight to ensure optimal soil penetration.
Product overview: Stickies control agent can reduce the cohesiveness of resin composition in paper pulp and waste paper pulp by utilizing own positive electricity to fix them on pulp, thus preventing the pollution of net, coarse calico, dryer, etc. due to resin. In the meanwhile, it can reduce the shutdown and yield loss caused due to cleaning deposit. Technical specifications �· Appearance: Colorless to faint yellow liquid �· Solids content: 30 �±1% �· pH value: 2% water solution 3-7 �· Viscosity (25�°C): 500-3000 mpa.s �· Ionic type: Cation Performance characteristics 1. It can reduce the cohesiveness of resin composition in paper pulp and waste paper pulp by utilizing own positive electricity to fix them on pulp, thus preventing the pollution of net, coarse calico, dryer, etc. due to resin. 2. It can reduce the shutdown and yield loss caused due to cleaning deposit. 3. It can improve the paper machine vehicle speed and paper quality. 4. It is stable in acid, alkali and temperature. 5. It is soluble in water and generate a little bubble. Usage tips �· Adding place: It shall be added near the resin obstacles with good mixing. �· Adding method: The product is diluted for 10-20 times with clean water, with even mixing. �· Additive amount: 0.2-0.8 kg/ton slurry. Packing and storage �· It is packaged in 200kg or 1000kg plastic barrel, or packaged according to the users' requirements. It shall be stored in cool place (storage temperature at 0-30), with guarantee period: 6 months.
Multiple Protections: Dry run protection Phase loss protection Overload/no load protection Short circuit protection Over-voltage protection Pump stalled/antiseizing protection Undervoltage protection Pump shaft rust protection Major Features: 1,Pressure control: electric contact pressure gauge or pressure switch 2,Water level control: probe or float switch 3,Multifunction display â?? visualization of: voltage, motor current, upper/lower tank status and alarms 4,Upper tank for water supply control and lower tank for drainage control 5,Operation mode: AUTO/MANUAL switch 6,Fault indication: fault tracking,last 10 fault reason display,audio/light alarms. 7,Anti-card protection,long-term non-use of the pump, 15 days to start once. 8,Setting protection current for motor overload/no-load,no-load delay restart time adjustable. 9,Automatic restart when voltage comes to normal rating after over-voltage/under-voltage protection. 10,Automatic restart after power failure recovery. 11,Time setting ON/OFF 12,Push button for adjustments and set up from display 13,Restore factory setting: press both "Overload" and "NO-Load"for 3 seconds. 14,Automatic re-starting pump from dry running,restart time range 0-999 minutes adjustable.
Multiple Protections:  Dry run protection Phase loss protection Overload/no load protection Short circuit protection Over-voltage protection Pump stalled/antiseizing protection Undervoltage protection Pump shaft rust protection Major Features: 1,Pressure control: electric contact pressure gauge or pressure switch 2,Water level control: probe or float switch 3,Multifunction display â?? visualization of: voltage, motor current, upper/lower tank status and alarms 4,Upper tank for water supply control and lower tank for drainage control 5,Operation mode: AUTO/MANUAL switch 6,Fault indication: fault tracking,last 10 fault reason display,audio/light alarms. 7,Anti-card protection,long-term non-use of the pump, 15 days to start once. 8,Setting protection current for motor overload/no-load,no-load delay restart time adjustable. 9,Automatic restart when voltage comes to normal rating after over-voltage/under-voltage protection. 10,Automatic restart after power failure recovery. 11,Time setting ON/OFF 12,Push button for adjustments and set up from display 13,Restore factory setting: press both "Overload" and "NO-Load"for 3 seconds. 14,Automatic re-starting pump from dry running,restart time range 0-999 minutes adjustable.
Multiple Protections:  Dry run protection  Phase loss protection Overload/no load protection  Short circuit protection Over-voltage protection  Pump stalled/antiseizing protection Undervoltage protection  Pump shaft rust protection Major Features: 1,Pressure control: electric contact pressure gauge or pressure switch 2,Water level control: probe or float switch 3,Multifunction display â?? visualization of: voltage, motor current, upper/lower tank status and alarms 4,Upper tank for water supply control and lower tank for drainage control 5,Operation mode: AUTO/MANUAL switch 6,Fault indication: fault tracking,last 10 fault reason display,audio/light alarms. 7,Anti-card protection,long-term non-use of the pump, 15 days to start once. 8,Setting protection current for motor overload/no-load,no-load delay restart time adjustable. 9,Automatic restart when voltage comes to normal rating after over-voltage/under-voltage protection. 10,Automatic restart after power failure recovery. 11,Time setting ON/OFF 12,Push button for adjustments and set up from display 13,Restore factory setting: press both "Overload" and "NO-Load"for 3 seconds. 14,Automatic re-starting pump from dry running,restart time range 0-999 minutes adjustable.
Multiple Protections Dry run protection Phase loss protection âOverload/no load protection â? Short circuit protection â? Over-voltage protection â? Pump stalled/antiseizing protection â? Undervoltage protection â? Pump shaft rust protection Major Features: 1,Pressure control: electric contact pressure gauge or pressure switch 2,Water level control: probe or float switch 3,Multifunction display â?? visualization of: voltage, motor current, upper/lower tank status and alarms 4,Upper tank for water supply control and lower tank for drainage control 5,Operation mode: AUTO/MANUAL switch 6,Fault indication: fault tracking,last 10 fault reason display,audio/light alarms. 7,Anti-card protection,long-term non-use of the pump, 15 days to start once. 8,Setting protection current for motor overload/no-load,no-load delay restart time adjustable. 9,Automatic restart when voltage comes to normal rating after over-voltage/under-voltage protection. 10,Automatic restart after power failure recovery. 11,Time setting ON/OFF 12,Push button for adjustments and set up from display 13,Restore factory setting: press both "Overload" and "NO-Load"for 3 seconds. 14,Automatic re-starting pump from dry running,restart time range 0-999 minutes adjustable.
TECHNICAL SPECIFICATION OF 150KVA THREE PHASE OIL COOLED SERVO VOLTAGE STABILIZER 1. Capacity : 150KVA Three Phase 2. Model : Make SERVOSINE 3. Input Voltage Range : 190V-270V 1Phase / 340V-470V 3 Phase 4. Output Voltage : 230V +/-1% 1 PH / 400V +/-1% 3 PH 5. No. of phases : Three, 4 Wire 6. Line Frequency : 47-53Hz. 7. Output Voltage Regulation : +1% 8. Type of Cooling : Oil Cooled 9. Type : Unbalanced supply and Load conditions 10. Efficiency :> 98% 11. Speed of Correction : 30V per sec (For 3 Phase) 12. Wave form distortion : Nil 13. Effect of Load power factor : Nil, Suitable for all power factors 14. Ambient Temperature : 0-65�ºC with RH 90% 15. Duty Cycle : Continuous 16. Indications on each phase : Input Mains, Input Low, Input Voltage, Input High, Out Voltage. 17. Controls on each Phase : Auto/Manual Push Button, Increase/Decrease Push Button Voltâ??s adjuster Set Button 18. Metering : Digital 19. Mounting : On Wheel 20. Construction : MS Sheet Body, Prime Grade Powder Coating 21. Spares Availability : Available with Company 22. Transformer Winding : Prime Grade Copper Wire on CRGO Core 23. Servicing & Maintenance : Easley can be do by any technical known Person And from company side on call log.
TECHNICAL SPECIFICATION OF 100KVA THREE PHASE OIL COOLED SERVO VOLTAGE STABILIZER 1. Capacity : 100KVA Three Phase 2. Model : Make SERVOSINE 3. Input Voltage Range : 190V-270V 1Phase / 340V-470V 3 Phase 4. Output Voltage : 230V +/-1% 1 PH / 400V +/-1% 3 PH 5. No. of phases : Three, 4 Wire 6. Line Frequency : 47-53Hz. 7. Output Voltage Regulation : +1% 8. Type of Cooling : Oil Cooled 9. Type : Unbalanced supply and Load conditions 10. Efficiency :> 98% 11. Speed of Correction : 30V per sec (For 3 Phase) 12. Wave form distortion : Nil 13. Effect of Load power factor : Nil, Suitable for all power factors 14. Ambient Temperature : 0-65C with RH 90% 15. Duty Cycle : Continuous 16. Indications on each phase : Input Mains, Input Low, Input Voltage, Input High, Out Voltage. 17. Controls on each Phase : Auto/Manual Push Button, Increase/Decrease Push Button Volt adjuster Set Button 18. Metering : Digital 19. Mounting : On Wheel 20. Construction : MS Sheet Body, Prime Grade Powder Coating 21. Spares Availability : Available with Company 22. Transformer Winding : Prime Grade Copper Wire on CRGO Core 23. Servicing & Maintenance : Easley can be do by any technical known Person And from company side on call log.
Technical Specification Of 75kva Three Phase Oil Cooled Servo Voltage Stabilizer 1. Capacity : 75KVA Three Phase 2. Model : Make SERVOSINE 3. Input Voltage Range : 190V-270V 1Phase / 340V-470V 3 Phase 4. Output Voltage : 230V +/-1% 1 PH / 400V +/-1% 3 PH 5. No. of phases : Three, 4 Wire 6. Line Frequency : 47-53Hz. 7. Output Voltage Regulation : +1% 8. Type of Cooling : Oil Cooled 9. Type : Unbalanced supply and Load conditions 10. Efficiency :> 98% 11. Speed of Correction : 30V per sec (For 3 Phase) 12. Wave form distortion : Nil 13. Effect of Load power factor : Nil, Suitable for all power factors 14. Ambient Temperature : 0-65�ºC with RH 90% 15. Duty Cycle : Continuous 16. Indications on each phase : Input Mains, Input Low, Input Voltage, Input High, Out Voltage. 17. Controls on each Phase : Auto/Manual Push Button, Increase/Decrease Push Button Voltâ??s adjuster Set Button 18. Metering : Digital 19. Mounting : On Wheel 20. Construction : MS Sheet Body, Prime Grade Powder Coating 21. Spares Availability : Available with Company 22. Transformer Winding : Prime Grade Copper Wire on CRGO Core 23. Servicing & Maintenance : Easley can be do by any technical known Person And from company side on call log.
TECHNICAL SPECIFICATION 1. Capacity : 50KVA Three Phase 2. Model : Make SERVOSINE 3. Input Voltage Range : 190V-270V 1Phase / 340V-470V 3 Phase 4. Output Voltage : 230V +/-1% 1 PH / 400V +/-1% 3 PH 5. No. of phases : Three, 4 Wire 6. Line Frequency : 47-53Hz. 7. Output Voltage Regulation : +1% 8. Type of Cooling : Oil Cooled 9. Type : Unbalanced supply and Load conditions 10. Efficiency :> 98% 11. Speed of Correction : 30V per sec (For 3 Phase) 12. Wave form distortion : Nil 13. Effect of Load power factor : Nil, Suitable for all power factors 14. Ambient Temperature : 0-65 C with RH 90% 15. Duty Cycle : Continuous 16. Indications on each phase : Input Mains, Input Low, Input Voltage, Input High, Out Voltage. 17. Controls on each Phase : Auto/Manual Push Button, Increase/Decrease Push Button Voltâ??s adjuster Set Button 18. Metering : Digital 19. Mounting : On Wheel 20. Construction : MS Sheet Body, Prime Grade Powder Coating 21. Spares Availability : Available with Company 22. Transformer Winding : Prime Grade Copper Wire on CRGO Core 23. Servicing & Maintenance : Easley can be do by any technical known Person And from company side on call log.
1. Equipment usage: This testing ± 1/500000, Relative error of indication: better than ± 1% of the indication, 2 displacement (moving crossbeam, excluding stretching fixture), Measurement range: 0-700mm, Resolution: 0.0025mm, 3 Test speed: Speed adjustment range: 0.01-500mm/min (stepless speed regulation), Accuracy: better than ± 0.5% of the indicated value, Displacement rate control accuracy: within ± 1.0% of the set value when the rate is less than 0.1mm/min; When the speed is 0.1mm/min, within ± 0.2% of the set value, 4 Control: Force control speed regulation range: 0.005-5% F.S/S, Force control rate control accuracy: within �± 2% of the set value when the rate is less than 0.05% FS/S; When the rate is 0.05% FS/S, within the set value of ± 0.5%/ ± 1.0%, Deformation speed regulation range: 0.005% FS/S, Deformation rate control accuracy: within ± 2% of the set value when the rate is less than 0.05% FS/S; When the rate is 0.05% FS/S, it is within ± 0.5% of the set value, Constant force, constant deformation, and constant displacement control range: 0.5% -100% FS/S, Constant force, constant deformation, and constant displacement control accuracy: within ± 0.1% of the set value when the set value is â 10% FS; When the set value is less than 10% FS, within ± 1% of the set value. 5 Effective test space (with fixture): Effective stretching space: 700mm, Effective compressed space: 700mm, 6. Working environment: Room temperature 10~35 , humidity 20%~80%, 7. Power supply for the entire machine: single-phase, 220V ± 10%, 50Hz, 8 Host size: 530 370 1400mm, 9 Weight: 140 kg,
Forklift Series Lithium Iron Phosphate Battery Pack Parameters Series parameters Remarks No Items 48V 72V 80V 1 Cell material type Lithium iron phosphate 2 Nominal voltage 51.2 76.8 83.2 3 Operating voltage range 40-58.4 60-87.6 65-94.9 4 Nominal capacity 172-700 Customizable within the range 5 Charge cut-off voltage 58.4 87.6 94.9 6 Discharge cut-off voltage(V) 40 60 65 7 Standard charging current(A) 1 Constant current charging at 25 C ambient conditions 8 Standard discharge current (A) 1 Constant current discharge at 25 C ambient conditions 9 Discharge operating temperature range 10 Charging temperature range 11 Storage ambient temperature) (-20 - 55, short term, within 1 month; 0 - 35, long term, within 1 year) 12 Storage environment humidity(RH) 5% 95% 13 Humidity of the working environment(RH) 85% 14 Cycle life at room temperature 25 C, 3000 cycles (80% of rated capacity) 1C charge/discharge multiplier 15 High temperature cycle life 45 C, 2000 cycles (80% of rated capacity) 1C charge/discharge multiplier 16 Self-discharge rate at room temperature(%) 3%/month, 25 C 17 High temperature self-discharge rate (%) 5%/month, 45 C 18 High temperature discharge performance 95% (1. Battery charged in standard charging mode (battery charged at 1C constant current and constant voltage to 3.65V, cut-off current 0.05C; discharged at 1.0C constant current to a minimum discharge voltage of 2.5V at 45 C 2) 19 Low temperature discharge performance 70% (1. Battery charged in standard charging mode (battery charged at 1C constant current and constant voltage to 3.65V; discharged at 0.2C constant current to 2.5V at -20 2C) 20 Case size Customised according to customer requirements 21 Control systems BMS solutions
