Spring Loaded Pogo Pin Test Probe BIP68 Series for Battery Contact Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP68 series of battery contact probes. The outside diameter is usually 0.68 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 0.95 mm (37 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms (Maximum) Full Stroke: 0.5 mm Rated Stroke: 0.4 mm Spring Force: 10 gf (0.35 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Wire Harness Probe Pogo Pin CH203 Series for Electronic Test Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CH203 harness probe we will introduce here is 2.03 mm in diameter and 35.9 mm in total length. Its barrel is made of phosphor bronze plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of stainless steel plated with gold and nickel. This probe can withstand up to the current 5 Amps. Its typical maximum contact resistance is 50 milliohms. It is suggested the plunger be pressed at a distance of 5 mm at most when this probe works, although the plunger can move as far as 7.75 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 5 mm, its loaded force is about 145 gf, namely 5.5 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 5 Amps, continuous Contact Resistance: 50 milliohms Full Stroke: 7.75 mm Rated Stroke: 5 mm Spring Force: 145 ±43 gf (5.5 oz) at load 5 mm Materials (plated) Barrel: Phosphor Bronze, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SUS, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Cable Harness Contact Probe Pin CHL137 for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHL137 harness probe we will introduce here is 1.37 mm in diameter and 26.7 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 100 milliohms. It is suggested the plunger be pressed at a distance of 2.8 mm at most when this probe works, although the plunger can move as far as 4.2 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 2.8 mm, its loaded force is about 100 gf, namely 3.5 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 100 milliohms Full Stroke: 4.2 mm Rated Stroke: 2.8 mm Spring Force: 100 ±30 gf (3.5 oz) at load 2.8 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Interface Probe Straight Brass Pin IFP-002 for Transmitting Electrical Signals Interface probes are functional probes. They are not used for tests and only play a role in connection or control in switching functions, etc. Interface probes are used for transmitting electrical signals from one end to the other end in test fixtures. Interface probes manufactured by Centalic mainly include the models 001, 002, 003, 004, 005, 006 and 007 in IFP series. This product, IFP-002, is made from phosphor bronze or brass, plated with gold. Characterized by excellent conductivity, it is usually used for the connection of electronic components and functional tests. IFP-002 interface probe is 14.3 mm in total length. If customers wish to change its length or diameter, we could do as required. Unlike IFP-001, it has a base at the end. If the gold plating is expected to be thicken or thinned, we could try to do according to requirements. Customization is welcome. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
In-circuit Test Probe Pogo Pin PE75 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PE75 series here. Its test center is 75 mil. The diameter is 1.91 mm and the total length is 33.1 mm. Various tip styles, for example, A, B, U, H, K, L, BK, etc., are available for test probes. There are roughly three types of receptacles, namely CR, SC and WW to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.91 mm (75 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms Mounting Hole Size: Diameter 1.35 mm Full Stroke: 6.4 mm Rated Stroke: 4.3 mm Spring Force: 150 gf (5.5 oz)/200 gf (7.2 oz)/227 gf (8 oz) Materials Receptacle: Brass, Gold Plated Contact Barrel: Phosphor Bronze, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Nickel Plated or Gold Plated semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Pogo Pin Test Probe BIP47 Series for Battery Contact Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP47 series of battery contact probes. The outside diameter is usually 1.6 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 2.54 mm (100 mil) Current Rating: 3 Amps, continuous Contact Resistance: 20 milliohms (Maximum) Full Stroke: 1.5 mm Rated Stroke: 1.5 mm Spring Force: 80 gf (2.8 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Wire Harness Probe Pogo Pin CHL165 for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHL165 harness probe we will introduce here is 1.65 mm in diameter and 35.4 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 100 milliohms. It is suggested the plunger be pressed at a distance of 3.5 mm at most when this probe works, although the plunger can move as far as 5.3 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 3.5 mm, its loaded force is about 113 gf, namely 4 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 100 milliohms Full Stroke: 5.3 mm Rated Stroke: 3.5 mm Spring Force: 113�?�±35 gf (4 oz) at load 3.5 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980.Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Cable Harness Probe Pogo Pin CHL265 for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHL265 harness probe we will introduce here is 2.65 mm in diameter and 28.4 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 100 milliohms. It is suggested the plunger be pressed at a distance of 3.5 mm at most when this probe works, although the plunger can move as far as 5.5 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 3.5 mm, its loaded force is about 113 gf, namely 4 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 100 milliohms Full Stroke: 5.5 mm Rated Stroke: 3.5 mm Spring Force: 113�?�±35 gf (4 oz) at load 3.5 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980.Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Interface Probe Straight Metal Pin IFP-003 for Transmitting Electrical Signals Interface probes are functional probes. They are not used for tests and only play a role in connection or control in switching functions, etc. Interface probes are used for transmitting electrical signals from one end to the other end in test fixtures. Interface probes manufactured by Centalic mainly include the models 001, 002, 003, 004, 005, 006 and 007 in IFP series. This product, IFP-003, is made from phosphor bronze or brass, plated with gold. Characterized by excellent conductivity, it is usually used for the connection of electronic components and functional tests. IFP-003 interface probe is 16.33 mm in total length. If customers wish to change its length or diameter, we could do as required. Unlike IFP-001, it has a base at the end. If the gold plating is expected to be thicken or thinned, we could try to do according to requirements. Customization is welcome. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
Interface Pin Test Probe IFP-005 for Transmitting Electrical Signals Interface probes are functional probes. They are not used for tests and only play a role in connection or control in switching functions, etc. Interface probes are used for transmitting electrical signals from one end to the other end in test fixtures. Interface probes manufactured by Centalic mainly include the models 001, 002, 003, 004, 005, 006 and 007 in IFP series. This product, IFP-005, is made from phosphor bronze or brass, plated with gold. Characterized by excellent conductivity, it is usually used for the connection of electronic components and functional tests. IFP-005 interface probe is 17.8 mm in total length. If customers wish to change its length or diameter, we could do as required. Unlike IFP-001, it has a base at the end. If the gold plating is expected to be thicken or thinned, we could try to do according to requirements. Customization is welcome. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
Cable Harness Probe Pogo Pin CH136-J for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CH136 harness probe we will introduce here is 1.36 mm in diameter and 33 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 50 milliohms. It is suggested the plunger be pressed at a distance of 5.3 mm at most when this probe works, although the plunger can move as far as 8 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 5.3 mm, its loaded force is about 57 gf, namely 2 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Full Stroke: 8 mm Rated Stroke: 5.3 mm Spring Force: 57±17 gf (2 oz) at load 5.3 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980.Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Spring Pogo Pin Battery Contact Test Probe BIP94 for Connector Application Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP94 series of battery contact probes. The outside diameter is usually 0.94 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.27 mm (50 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms (Maximum) Full Stroke: 0.78 mm Rated Stroke: 0.7 mm Spring Force: 30 gf (1.05 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu/SK4, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Battery Contact Probe Test Pogo Pin BIP148 Series for Connector Application Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP148 series of battery contact probes. The outside diameter is usually 1.49 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 2.16 mm (85 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms (Maximum) Full Stroke: 2 mm Rated Stroke: 1.33 mm Spring Force: 25 gf (1/ 0.9 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
PCBA Assembly Test Probe Pogo Pin PQL50 Series Applied to ICT In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PQL50 series here. Its diameter is 0.78 mm and the total length is 43.2 mm. Various tip styles, for example, H, S, T, E, C, U, G, etc., are available for test probes. There are roughly four types of receptacles to fit the probes, for instance, CR, SW, CRW and WW. The plunger can be pressed at a distance of up to 6.35 mm. But it is better to be pressed at a distance of 4.3 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 4.3 mm, the loaded force is about 5.5 oz, 7 oz or 8 oz, which fluctuates to a tolerance. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.27 mm (50 mil) Current Rating: 3 Amps, continuous Contact Resistance: 60 milliohms Mounting Hole Size: Diameter 1 mm Full Stroke: 6.35 mm Rated Stroke: 4.3 mm Spring Force: 150 gf (5.5 oz)/ 185 gf (7 oz)/ (227 gf (8 oz) Materials Receptacle: Phosphor Bronze, Gold Plated Contact Barrel: Phosphor Bronze, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper, Nickel Plated or Gold Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Pogo Pin Test Probe BIP114 Series for Battery Contact Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP114 series of battery contact probes. The outside diameter is usually 1.14 mm and there are some common tip styles, for example round head or pointed head. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.91 mm (75 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms (Maximum) Full Stroke: 1.14 mm Rated Stroke: 1.14 mm Spring Force: 110 gf (4 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Electronic Test Probe Double-sided Spring Pogo Pin SCPA057 for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. SCPA057 series is a medium-sized one in all semiconductor test probes. Both plungers are movable. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. Its parameters are as below. Materials (plated) Barrel: Ph, Au on Ni Plated Bottom Plunger: BeCu, Au on Ni Plated Top Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 3 Amps Contact Resistance: 100 milliohms, max Bandwidth: 5 GHz at -1dB Propagation Delay: 24 ps Inductance: 1MHZ at -0.03664 uH Captance: 1MHZ at -0.704638 uF Specifications: Full Stroke: 0.63 mm Rated Stroke: 0.5 mm Spring Force: 45 ±13 gf at load 0.5 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Triple Offset Butterfly Valve manufacturer in the topmost Triple Offset Butterfly Valve manufacturer in We provide high-quality and reliable valves at competitive prices. The triple offset butterfly valve is also known as a Triple eccentric butterfly valve. Because of its metal sealing, the thermal shocks and pressure peaks are getting reduced. This design allows for low-torque operation. The composite stainless steel sealing on our triple offset butterfly valve ensures that there is no leakage. This makes the valve more resistant to high temperature, high pressure, and corrosion. Whenever the valve body is opened or closed, there is no friction happens between the disc and the valve body throughout the rotation. What is a Butterfly Valve A butterfly valve is a member of the family of quarter-turn, bi-directional, rotary motion valves used to stop, control, or start flow. Quarter valves are the kind of valves that only require a quarter turn of the disc to fully open or fully close the flow. In order to transition from the completely open to the fully closed position, quarter turn valves simply need to be rotated 90 degrees. They are also known as fast-acting valves for this reason. The shape and movement of the plug give the butterfly valve its name. The plug has a rod running through it and is formed like a disc, giving it the appearance of wings. The disc rotates by a quarter when the rod is turned, falling perpendicular to the flow and stopping it. The disc is rotated back to its original position, which is away from the flow in order to restart the flow. To regulate the flow, the valve can also be opened gradually. Description: Class: 150 to 600 Material: Cast iron, Ductile iron, Stainless steel (SS304, SS316, F304, F316, CF8, CF8M, SS316L, SS409L), Carbon steel, Duplex steel. End Connection: Wafer, Lug, Flanged Size: Pressure: PN6 to PN300 Operation: Gear Operated, Electric Actuated, Pneumatic Actuated
Specialityvalve is one of the top notch Pneumatic Knife Gate Valve Manufacturer in India. The Pneumatic Knife Gate Valve has a blade to cut through the clogging of heavy liquids. The valve is used in a lots of processing plants and it comes in larger sizes which makes them easier to handle. The Pneumatic Knife Gate valves are mostly used to shut off fluid flow in a fully open position, provide full flow. It is used in industries which deals with fluids. This pneumatic knife gate valve is operated automatically, using an actuator. Types of Pneumatic knife gate valve:- Pneumatic Bidirectional knife gate valvePneumatic Unidirectional knife gate valve Pneumatic Knife Gate Valve are used in industries such as: Chemical industry Refineries Mining and Mineral process Power Plant Cement Industry Description:- Materials: Cast Iron , Ductile Iron, CF8M, CF8, SS316, SS304 CF3M, WCB. Ends: Wafer, Lug, Flanged Size: 2 to 80 Class: 150 to 600 Pressure: PN 100 PN 450 Operations: Pneumatic Actuated Configuration for pneumatic actuators: Pneumatic single acting actuators Pneumatic double acting actuators Pneumatic rotary actuators Pneumatic Scotch and Yoke actuators Pressure: 25 bar Temperature: Standard -4F to 200F (-20C to 93C) Low -40F to 176 F (-40C to 80C) High 0F to 300�°F (-18C to 149C) Looking for the best Pneumatic Knife Gate Valve? Specialityvalve is the best Pneumatic Knife Gate Valve Manufacturer in India. Here we supply valves to our clients globally. We provide customized valves of the best quality and it is cost-effective. Our company main aim is quality, safety, and reliability of our products. Our valves are manufactured using best quality materials in our advanced manufacturing unit.
Specialityvalve is one of the best Awwa valve manufacturer in India. Awwa valves regulate the flow and pressure of fluids, gases, and slurries within a structure. They're also known as controllers, and they're used in a variety of applications. Valves vary greatly in terms of size, shape, capacity, and activity. Valve characterization can be accomplished using a variety of techniques, including the control component and valve work. Specialtyvalve may also make custom valves for you or deliver you wholesale quantities of your chosen product. There are different type of Awwa valve Awwa Gate Valve Awwa Check Valve Awwa Butterfly Valve Advantages of Awwa valve: It works to control the pressure among different units as required by each unit. Awwa valve is used in many industries like Oil and Gas Industries Food and Beverages Industries Chemicals Industries Water and Wastewater Treatment Where to get the best Awwa valve? Specialityvalve is one of the leading Awwa valve Manufacturer in India. We supply valves to our clients all over the world. We provide valves of the best quality and our valves are cost-effective. The main aim of our company is quality, safety, and reliability of our products. Our valves are manufactured using premium quality materials in our advanced manufacturing unit. Material: Cast Iron Awwa valve, Ductile iron Awwa valve. Ends: Flanged, Wafer, Lug Pressure: PN6- PN25 Size: 2 to 72 Operations: Electric actuated, Pneumatic actuated, Gear operated, Handwheel, lever operated.
Buy kinder joy online A special part of so many childhood memories, KINDER SURPRISE is the chocolate treat Mom reaches for to delight her children with three things she knows they will love: a surprise, a delicious Kinder chocolate egg, and an imaginative toy to build and play with. And as of 2011, KINDEr SURPRISE has fit even more WOW! into every surprise with fantastic new, eye-popping toys guaranteed to make everyday moments of shared joy even more special. Buy kinder joy online Kinder JOY Eggs, 15 Count, Individually Wrapped Bulk Chocolate Candy Eggs With Toys Inside & Applaydu: Kids Games By Kinder, Perfect Surprise For Kids, 10.5 Oz, PACKAGING MAY VARY. kids love kinder joy. Each iconic Kinder JOY egg holds a delicious treat on one sideâ?¦and a fun toy on the other, 15-count pack â?? great for surprise treats, gifts, or party favors for boys and girls. â??Two delicious cream layers â?? one sweet milk-cream flavored and one cocoa flavored â?? with two crispy, chocolate-covered wafer bites. Bring your kidâ??s toys to life and extend the Kinder Joy playing experience with Applayduâ?? Augmented reality activities that bring toys to life and virtual arts and crafts to enhance their creativity and extend learning100% free to download, playable offline, no ads, and no in-app purchases Tons of stimulating Entertainment and Education kids mini-games covering different topics. Toys and packaging may vary; WARNING: Choking Hazard Small parts. Not for children under 3 years. Buy kinder joy online
