In making briquettes, 2.5% starch adhesive is used which is cold pressed at a pressure of 3.125 tonnes. The research results showed that compared to briquettes made from 100% sawdust charcoal, the addition of coconut shell charcoal was able to increase the density, compressive strength and calorific value. Overall the density value of charcoal briquettes ranged from 0.45-0.59 g/cm3, compressive strength 4.67-6.72 kg/cm2, water content 3.51-4.75%, volatile matter content 22.18-25.77. ash content 3.56-4.23%, bound carbon content 70.28-73.82% and calorific value ranging from 6,198.99-6,522.84 cal/g
Product name inconel mesh inconel wire screen  inconel screen  inconel fabric Material: inconel 600 625 718 and others Mesh count:1-200 mesh Wire diameter:0.05-5 mm and others Hole:20-0.077mm Weave type:plain/twill weave Roll width:0.9 1 1.2 1.5 1.8 2 meters Roll Length:30 60 meters or customized Application: Aerospace� � Chemical Processing Electronic Components Food Processing Gas Turbine Components Heat Exchangers Pressure Valves Pulp & Paper
Product Description It is a kind of tankless, lager-caliber tube and low-pressure solar water heater system with the following features: Capacity: The system contains 4-8 pieces of vacuum tubes as one unit, with each tube capacity of 16 liters of water. this one is 4 pieces of vacuum tubes as one unit. Tankless: Inside each tube, there is a high-temperature-resistant and corrosion-resistant stainless-steel cylinder made of food-grade 304/316 material, so the solar heater does not require a water tank like other products in the market, thus saving space. Pressurized mode: the heater is pressurized. It is connected to the tap-water supply system and on the other side it is connected to the shower head in the bathroom, so the pipeline is relatively simple, and the installation and maintenance are also simple and convenient. Flexible installation position Because this water heater is connected to tap-water supply system(pressurized), it can be installed anywhere for buildings, such as on the ground, the roof, the balcony, the terrace etc., whether high-rise building, multi-story building, bungalow or villa. Installation method: vertical, horizontal, inclined etc. installation Limescale prevention: Pre-filter as a standard feature gives an effective limescale prevention solution to avoid any potential worry. Excellent insulation: Each tube is equivalent to a thermos bottle, which has good insulation performance, and there is air between the steel cylinder and the glass tubes, which also provides the added thermal insulation. and the tube openings are also insulated by good materials, ensuring optimal heat retention. Based on our experiments conducted on the rooftop of an eight-story building, with daytime temperatures reaching 7C and nighttime temperatures dropping to -3C or -5C, it is observed that when 15C water was injected at 9 AM, the water temperature ranged from 51C to 64C at 17:00 PM. The following morning at 8 AM, the water temperature ranged from 42C to 47C, and by 17:00 PM, the temperature of the hot water reached 85C. The highest energy efficiency: due to its large area of absorption of sunlight, it is with good energy efficient whose hot water outlet is the highest. Automatic anti-freeze function: when the temperature falls below 5 C, the system will automatically activate the anti-freeze electric heating feature. optional devices: electric auxiliary heating pump station, gas water heater, electric water heater can be added to our heater system as auxiliary components to be used if weak or lack of sunlight. Customers can choose one out of above-mentioned three.
Product Description It is a kind of tankless, lager-caliber tube and low-pressure solar water heater system with the following features: Capacity: The system contains 4-8 pieces of vacuum tubes as one unit, with each tube capacity of 16 liters of water. this one is 3 pieces of vacuum tubes as one unit. Tankless: Inside each tube, there is a high-temperature-resistant and corrosion-resistant stainless-steel cylinder made of food-grade 304/316 material, so the solar heater does not require a water tank like other products in the market, thus saving space. Pressurized mode: the heater is pressurized. It is connected to the tap-water supply system and on the other side it is connected to the shower head in the bathroom, so the pipeline is relatively simple, and the installation and maintenance are also simple and convenient. Flexible installation position Because this water heater is connected to tap-water supply system(pressurized), it can be installed anywhere for buildings, such as on the ground, the roof, the balcony, the terrace etc., whether high-rise building, multi-story building, bungalow or villa. Installation method: vertical, horizontal, inclined etc. installation Limescale prevention: Pre-filter as a standard feature gives an effective limescale prevention solution to avoid any potential worry. Excellent insulation: Each tube is equivalent to a thermos bottle, which has good insulation performance, and there is air between the steel cylinder and the glass tubes, which also provides the added thermal insulation. and the tube openings are also insulated by good materials, ensuring optimal heat retention. Based on our experiments conducted on the rooftop of an eight-story building, with daytime temperatures reaching 7C and nighttime temperatures dropping to -3C or -5C, it is observed that when 15C water was injected at 9 AM, the water temperature ranged from 51C to 64C at 17:00 PM. The following morning at 8 AM, the water temperature ranged from 42C to 47C, and by 17:00 PM, the temperature of the hot water reached 85C. The highest energy efficiency: due to its large area of absorption of sunlight, it is with good energy efficient whose hot water outlet is the highest. Automatic anti-freeze function: when the temperature falls below 5 C, the system will automatically activate the anti-freeze electric heating feature. optional devices: electric auxiliary heating pump station, gas water heater, electric water heater can be added to our heater system as auxiliary components to be used if weak or lack of sunlight. Customers can choose one out of above-mentioned three.
Liquid sodium silicate products are slightly sticky, but they have only moderate tack compared to many organic pressure sensitive adhesives. As the water evaporates, liquid silicates become progressively tackier and more viscous. Generally, only a small portion of the water (several percent by weight) needs to evaporate before the adhesive exhibits good handling strength. Therefore, sodium silicate adhesives are often employed in applications requiring high machine speeds and fast setting characteristics. The effects of water evaporation on the viscosities of several liquid sodium silicate products are shown in the table below.
Product Description The Abu Garcia Ambassadeur S Casting Combos are made with performance and reliability all in one package. These combos are made with a compact bent handle and star to provide a more ergonomic design. Features: 2 stainless steel ball bearings for smooth operation Smooth and consistent multi disc drag system 4 pin centrifugal brake gives consistent brake pressure throughout the cast Synchronized level wind system improves line lay and castability 24 ton graphite for a lightweight balanced design Texas rigged hook keeper for all bait applications Light weight cork grips
Product Description The Abu Garcia Ambassadeur STX Round Baitcasting reels are made with quality and are dependable. These reels also provide excellent casting control along with ergonomic feel and durability. The Ambassadeur STX series reels delivers true on the water performance. Features: 4 stainless steel ball bearings + 1 roller bearing provides smooth operation Multi disc drag system gives smooth drag performance Compact bent handle and star provide a more ergonomic design 6 pin centrifugal brake gives consistent brake pressure throughout the cast Synchronized level wind system improves line lay and castability
This is a state-of-the-art sewing machine designed to streamline and automate the production of intricate patterns and designs. With its advanced computerized technology, this machine offers precise stitching and high-speed operation, making it an ideal choice for various industries such as apparel, automotive, upholstery, and home textiles. Computerized Operation: The machine is equipped with advanced computerized technology that allows for precise and automated stitching of complex patterns. Users can create and input custom designs through the machine's user-friendly interface, eliminating the need for manual pattern marking and reducing production time. Large Sewing Area: With a spacious sewing area of 300*200mm, this machine offers ample space to sew large-scale patterns and designs. The generous sewing area enables the creation of intricate and detailed designs on a wide range of fabrics and materials. High-Speed Performance: The Automatic Computerized Pattern Sewing Machine is capable of high-speed stitching, significantly increasing productivity and efficiency. The machine's precise motor control and optimized thread tension system ensure consistent stitch quality, even at high sewing speeds. Versatile Stitching Options: This machine offers a wide range of stitching options, including straight stitching, zigzag stitching, decorative stitching, and more. With the ability to customize stitch length, width, and density, users can achieve a variety of design effects and meet diverse application requirements. Model BS-2010 BS-3020 BS-6040 Sewing type SINGLE NEEDLE LOCKSTITCH Max sewing speed 2,800 RPM 2,800 RPM 2,800 RPM Stitching area 200x100 mm 300x200 mm 600x400 mm Cloth feeding device INTERMITTENT FEEDING (DRIVEN BY PULSE MOTOR) Needle gauge 0.05 -12.7mm Can be saved by code 50000 STITCHES/ SEWING PATTERN Highest sewing stitched for each pattern 20000(A PATTERN) Storage SD CARD BUILT-IN MEMORY:2GB, 900 KINDS Clamp drive PNEUMATIC Clamp height Max 35 mm Clamp lowest ONE-PIECE PRESSURE FOOT Pressure foot lift up 22 mm Intermittent pressure foot 0.2-4.5 mm OR 4.5 mm (FACTORY SETTINGS:3 mm) Shuttle (hook) DOUBLE HOOK(STANDARD) Thread wiper device STANDARD EQUIPMENT Trimmer device STANDARD EQUIPMENT Date memory FLASH MEMORY(CAN SAVE WITH SD CARD) 3 INCH DISK 2HD/1.44BM.2DD,USB INTERFACE No. of user programs 50 Loop program number 9 Motor SERVO MOTOR 750W Weight HEAD: 160 kg, OPERATING PANEL: 0.6 kg, CONTROL BOX: 16.2 kg Power SINGLE PHASE 220V 3-PHASE 200V/380V/400V 500VA Air pressure 0.5 Mpa 1.81/min
Product nameï inconel mesh inconel wire screen inconel screen inconel fabric Material: inconel 600 625 718 and others Mesh count:1-200 mesh Wire diameter:0.05-5 mm and others Hole:20-0.077mm Weave type:plain/twill weave Roll width:0.9 1 1.2 1.5 1.8 2 meters Roll Length:30 60 meters or customized Application: Aerospace Chemical Processing Electronic Components Food Processing Gas Turbine Components Heat Exchangers Pressure Valves Pulp & Paper
L05 RFID PPS LAUNDRY TAGS WASHABLE BUTTON LAUNDRY TAGS Dimension: 24 X 40mm, Hole: 2mm diameter Thickness: 2mm Material: PPS Chip Options: TK4100, EM4200, EM4305, MIFARE S50/S70, NFC NTAG213/216, Ultralight EV1 Ultralight EV1, etc Typical required activation field strength to read/write (at +25C): 112 dBuA/m/ 115 dBuA/m Typical programming cycles (at +25C): 100,000 times Data retention time (at +55C): > 10 years Simultaneous ldentification of Tags: Up to 50 tags per second (reader/antenna dependent Protection Class: IP 68(condition: water pressure 45bar, 10h)
We offer a UL/FM Approved and LPCB Certified wide range of EMACO Fire Hydrant and hose products following: 1. Angle Hose Valve 2. Pressure Restricting Valve 3. Oblique Landing Valve 4. Lay Flat Fire Hose, (Single & Double Jacket) 5. Fire Hose Reel 6. Lexus Hose/Nitrile Rubber Hose 7. Fog Nozzle/Spray Nozzle 8. Branch Pipe Nozzle With Control Valve 9. Hydrant Cabinets With Accessories 10. Pillar Hydrant 11. Breeching Inlet For more details, please contact me.
Logiball Elliptical Mainline test and seal injection packers are custom-made for the exact pipe dimensions and the available access to the storm sewer lines. The two end rubber bladders are covered with a soft rubber sleeve that provides superior seating against rough surfaces. Our elliptical grout packers are equipped with a localized pressure sensor and two injection grouting ports protected by a large, non-clogging adjustable rubber check-valves. Contact us if you need a special configuration. Rentals available, contact our sales department for further information.
Application The CLRT-01 Carbon Dioxide Volume Tester is a crucial tool in the beverage industry, focusing on gauging carbonation levels, which significantly impact the bubbly and sensory qualities of drinks, thus influencing product excellence and customer contentment. Specially crafted for CO2 volume assessment, the CLRT-01 employs an automated process to uncover the connection between pressure and temperature, a pivotal factor in thorough beverage quality analysis. By seamlessly merging these elements, it offers a profound understanding of carbonation dynamics, granting manufacturers the ability to maintain consistency, adapt formulations, and provide effervescence that resonates with consumer preferences and brand achievement. Automatic Testing and Shaking The tester automates the traditional manual process: Piercing the bottle cap â?? Opening the vent valve to release pressure â?? Closing the vent valve â?? Vigorously vibrating for 40 seconds â?? Recording the stabilized MPa pressure (while measuring liquid temperature) â?? Obtaining the carbon dioxide gas capacity test results. Technical Features 1.This unit is under precise PLC control (at an industrial-grade stability level) and operated through an HMI touch screen interface. 2.Agitating the sample bottle is achieved using a servo motor and gearbox transmission mechanism. 3.The design incorporates anti-leak features and includes accurate temperature and pressure measurement. 4.The process involves automated piercing and shaking. 5.Displacement and speed during piercing are controlled for accuracy. 6.The shaking parameters, including frequency and duration, can be customized. 7.Test results are guaranteed accurate due to the implementation of a highprecision pressuresensor. 8.Real-time temperature display is enabled by a precision temperature sensor. 9.Post-test, the carbonation volume is automatically and presented. 10.Designed to prevent leaks, this versatile tester is suitable for both bottles and cans. 11.(Optional) A microprinter can be incorporated for additional functionality. 12.(Optional) The inclusion of an RS 232 port and professional software provides further versatility. Main Parameters Test Range 0~1MPa Resolution 0.01KPa Shaking Speed Adjustable Piercing Speed 5mm/s (other available) Sample Height â?¤ 350mm (other available) Temp. range 0 ~ 30 Shaking time 40s (other available) Resolution 0.1
Accupressure Acupressure is an ancient healing art that uses the fingers to press important points all over the body. It works by stimulating the body's self-healing abilities. Acupressure mainly focuses on relieving pain and discomfort as well as responding to stress. When key points of the body are pressed, they promote blood circulation and relieve muscle tension. There is no side effect because no medicine is used the treatment therapy can be understood by anyone, in this book all the points are explained with picture. 1. Human body 2. Acupressure History and Classification 3. Acupressure Principle 4. Types of Pressure 5. Instructions for Acupressure Treatment 6. Diseases and Treatment by Acupressure 7. Some Cases of Application of Sujok Therapy
Forging press refers to the mechanical equipment used for forming and separating in forging and pressing. Forging and pressing machinery includes forging hammers for forming, mechanical presses, hydraulic presses, screw presses and flat forging machines, as well as uncoiling machines, straightening machines, shearing machines, forging manipulators and other auxiliary machinery. Forging and pressing machinery is mainly used for metal forming, so it is also called metal forming machine tool. Forging and pressing machinery is formed by applying pressure to the metal. Large force is its basic characteristic. Therefore, it is mostly heavy equipment, and the equipment is equipped with safety protection devices to ensure the safety of equipment and personal safety.
This system contains below parts and its description is as below: Battery watering plug (BWP): This plug is made from polyprolene material. It will allow water inside only when the electrolyte level is below plastic float inside. Please note that this BWP will not work on gravity water pressure. It requires Minimum 10 psi water pressure for normal operation. Each BWP has one adaptor for easy fitting in 30 MM TYPE THREAD CELL VENT PLUG. ( there is one more adaptor for lift battery cell 35 mm push in type ) Water feeding pump: It is a 12 v dc windshield washer Pump required to pump and supply water to BWP with pressure. There are two wires coming from battery (on which this system is installed) through Push to on switch. When the switch is pressed then Pump will get on and supply water to BWP (at a time to six nos. plugs.) Please refer images. DM water tank: It is a 5 liters tank used to store dm water. The water feed Pump is mounted on this tank only. Blue Color PU Tubing. : We are providing tubing in continuous shape. And user needs to cut the tube as req. and installed in between two plugs. There is blue color PVC dead cap to use in extreme last plug. Please see photo for ref. Small Plastic Connector: This connector connects 4 mm PU pipe from Pump with 6 m PU pipe to BWP. Please refer images. Push to ON switch and wires: The push to ON switch and wires provides 12 v dc supplies to water feed pump. Please refer image. Other Instructions: The BWP is a low weight delicate, accurate, sensitive plastic moulded and assembled product. So handle it gently, do not apply very high manual pressure to fix in battery cell. Otherwise the top cover will get damage. Keep minimum distance in between DM water tank and Lead acid Battery. When you want to TOP up DM water then simply press and hold Push to ON switch. Now Pump will feed water to each BWP and the flow will become Zero when all Battery cells electrolyte level reaches to BWP float point. When you press switch again then as the electrolyte level is there so every BWP will not allow water into battery cell. Package Contents: Water Storage Tank Pipeline /Water tubes Feed water Pump End Plugs Battery watering Plug
This system contains below parts and its description is as below: Battery watering plug (BWP): This plug is made from polyprolene material. It will allow water inside only when the electrolyte level is below plastic float inside. Please note that this BWP will not work on gravity water pressure. It requires Minimum 10 psi water pressure for normal operation. Each BWP has one adaptor for easy fitting in 30 MM TYPE THREAD CELL VENT PLUG. ( there is one more adaptor for lift battery cell 35 mm push in type ) Water feeding pump: It is a 12 v dc windshield washer Pump required to pump and supply water to BWP with pressure. There are two wires coming from battery (on which this system is installed) through Push to on switch. When the switch is pressed then Pump will get on and supply water to BWP (at a time to six nos. plugs.) Please refer images. DM water Tank: It is a 5 liters tank used to store dm water. The water feed Pump is mounted on this tank only. Blue color PU Tubing. : We are providing tubing in continuous shape. And user needs to cut the tube as req. and installed in between two plugs. There is blue color PVC dead cap to use in extreme last plug. Please see photo for ref. Small Plastic Connector: This connector connects 4 mm PU pipe from Pump with 6 m PU pipe to BWP. Please refer images. Push to ON switch and wires: The push to ON switch and wires provides 12 v dc supplies to water feed pump. Please refer image. Other Instructions: The BWP is a low weight delicate, accurate, sensitive plastic moulded and assembled product. So handle it gently, do not apply very high manual pressure to fix in battery cell. Otherwise the top cover will get damage. Keep minimum distance in between DM water tank and Lead acid Battery. When you want to TOP up DM water then simply press and hold Push to ON switch. Now Pump will feed water to each BWP and the flow will become Zero when all Battery cells electrolyte level reaches to BWP float point. When you press switch again then as the electrolyte level is there so every BWP will not allow water into battery cell. Package Contents: Water Storage Tank Pipeline /Water tubes Feed water Pump End Plugs Battery watering Plug Auto Feed Water Control Unit
Quality Product : Lowest Price : Benefit to the end user : Battery watering plug (BWP): This plug is made from polyprolene material. It will allow water inside only when the electrolyte level is below plastic float inside. Please note that this BWP will not work on gravity water pressure. It requires Minimum 10 psi water pressure for normal operation. Each BWP has one adaptor for easy fitting in 30 MM TYPE THREAD CELL VENT PLUG. ( there is one more adaptor for lift battery cell 35 mm push in type ). Water feeding pump: It is a 12 v dc windshield washer Pump required to pump and supply water to BWP with pressure. There are two wires coming from battery (on which this system is installed) through Push to on switch. When the switch is pressed then Pump will get on and supply water to BWP (at a time to six nos. plugs.) Please refer images. DM water tank: It is a 5 liters tank used to store dm water. The water feed Pump is mounted on this tank only. Blue color PU tubing : We are providing tubing in continuous shape. And user needs to cut the tube as req. and installed in between two plugs. There is blue color PVC dead cap to use in extreme last plug. Please see photo for ref. Small Plastic connector: This connector connects 4 mm PU pipe from Pump with 6 m PU pipe to BWP. Please refer images. Push to ON switch and wires: The push to ON switch and wires provides 12 v dc supplies to water feed pump. Please refer image. Other Instructions: The BWP is a low weight delicate, accurate, sensitive plastic moulded and assembled product. So handle it gently, do not apply very high manual pressure to fix in battery cell. Otherwise the top cover will get damage. Keep minimum distance in between DM water tank and Lead acid Battery. When you want to TOP up DM water then simply press and hold Push to ON switch. Now Pump will feed water to each BWP and the flow will become Zero when all Battery cells electrolyte level reaches to BWP float point. When you press switch again then as the electrolyte level is there so every BWP will not allow water into battery cell. Package Contents: Water Storage Tank Pipeline /Water tubes Feed water Pump End Plugs Battery watering Plug Auto Feed Water Control Unit
We are manufacture and supplier of Water Softening Equipment, which are highly used for different applications in various hospitals, dairies, pharmaceuticals, chemicals industries etc. These portable Water Purifiers are of optimum quality and have low maintenance and are easy to install. Features: Fit & forget maintenance free No salt or chemicals needed No maintenance, easy to install Mains pressure and flow rate unaffected Retains healthy minerals Little space required and safe Low running cost, negligible Power consumption Effective on RPVE, UPVC, CPVC, Copper, Brass, SS 304, SS316 No waste water
We are manufacture and supplier of Water Softening Equipment, which are highly used for different applications in various hospitals, dairies, pharmaceuticals, chemicals industries etc. These portable Water Purifiers are of optimum quality and have low maintenance and are easy to install. Features: Fit & forget maintenance free No salt or chemicals needed No maintenance, easy to install Mains pressure and flow rate unaffected Retains healthy minerals Little space required and safe Low running cost, negligible Power consumption Effective on RPVE, UPVC, CPVC, Copper, Brass, SS 304, SS316 No waste water
