Worked Cone Penetration,0.01mm : 220-250 Dropping point :194 min operating temperature: -20-120 Suitable for the lubrication of rolling bearings, sliding bearings and other friction parts of various mechanical equipment in the temperature range of -20 120
Material: high carbon spring steel, spring steel, stainless steel, alloy steel Compression Spring, Extension Spring : Wire Diameter: 0.2-40.0mm Torsion spring wire diameter :0.2-35mm Surface Finish: black , Zinc, Nickel, silver, golden, tin, powder coating, shot pin Applications: Automotive, medical device, agricultural machinery ,electronics, toy, electric power distribution. Extension spring hook include Germany hook, British hook, Side hook We can customize special design of springs based on your requirement.
Premium greases are formulated with both Lithium, calcium soap mixed type
Yellow transparent mp3 lithium grease get all kinds of packages
Lubricants, greases, base oil sn80, sn150, sn500.
Euro AP3 - Multi-purpose Grease is a high-quality premium product of Euroils. It is a Lithium based multi-functional, high temperature, water-resistant multipurpose greases & is suitable for all types of ball, roller bearings and moving parts of machinery, requiring grease lubrication. Euro AP3 Grease can be used for 27,000 km or more under normal conditions in long-route trucks, buses, MUVs, Cars, etc. RECOMMENDATIONS: Recommended for all grease-lubricated parts of automobiles including commercial vehicles.
Items Method ZD500C3 Grease Type Lithium Grease Color Yellow or Blue Texture Smooth and transparent NLGI 3#Thickener Type Lithium base-12-hydroxy Thickener Content 13%-15% Penetration Worked 60 GB/T 269 240-250 Dropping point min GB/T 4929 135-140 Copper Corrosion GB/T 7326 pass Base Fluid Properties Base Fluid Type Mineral Viscosity @40 cst GB/T 265 185 Viscosity @100 cst GB/T 265 12 Pour Point -20 Propertie Great in anti-water; Better mechanical invariability; Better anti-rust; Good oxidation stability; Can take place of calcium base and sodium base greases. This product is made of refined base oil, thickened by fatty acid metallic soap thickener, added with many kinds of additives, for instance, abrasion and extreme pressure resisting, anti-corrosive, antioxidant and rustproof etc.
Petrochemical : base oil / furnace oil / mho / cst range/ used engine oil / bitumen, Bio diesel : used cooking oil / specially blended soybean / canola oils for industrial use (insultating oil) / cnsl (cashe nut shell liquid) Automotive & industrial oils & lubricants (manufactured to every specific blend / brands ) Waste food solutions .Our logistics team can provide with prices based on ex tank in uae, fob in uae seaports and cif to the destination port of the buyers. we can arrange to supply in flexitanks (20ft container), ibc tanks and drums (208 litres)
Soda ash light / dense 99.2% sodium bicarbonate caustic soda flakes 99% sodium sulphate anhydrous (ssa) 99% sodium sulphite flakes (ssf) 60% sodium metabisulphate hydrogen peroxide (h2o2) 50% formic acid 85% glacial acetic acid paraffin wax liquid paraffin (white oil) lp 100 menthol crystal fumed silica deg (di ethylene glycol) mono ethylene glycol (meg) poly ethylene glycol (peg), base oil 150n, bs 150, 600n bitumen 60/70 rpo (rubber process oil) lioh (lithium hydroxide) hco (hydrogenated castor oil) 12 hsa (hydroxy stearic acid) ferrous sulphate heptahydrate additive for lubricating oil aromatic chemicals.Exporting of chemicals & other products
We have all kind of D2 and Bace Oil bulk quantities available. We have also bitomen with cheap price available stock. Base oils are used to manufacture products including lubricating greases, motor oil and metal processing fluids. Product origin : Russia Key Specifications/Special Features : Grades : SN 150, SN 300, SN 500 Size and Packgaing details : Flexitank, IBC, Drums
Base oil sn60, 70, 100, 150, 350, 400, 500, 550, 600, 650; jet fuel a1, jp54, crude oil, bitumen 50,60/70, 90/100 & all grades of bitumen, used cooking oil, transformer oil, industrial oil, all types of grease, lng/lpg, used motor or engine oil, all types of motor oil, lubricants, additives and types of petroleum products.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
PAO 4 - 10 CST Product Uses: The 4-10 CST PAOs are used as synthetic base fluids for high-performance industrial and automotive lubricants (e.g., gear oils, compressor oils, hydraulic fluids, greases, engine oils) and functional fluids (e.g., dielectric, heat transfer, drilling). Almost all products go into lubricant applications.
Commodity 1 provides Lithium ore directly from the mine site to the global market. There are no middlemen involved, only our staff on the ground. We strive to organize smooth and transparent transactions. We believe in building long-term relationships with our customers. We aim to be our customers�¢?? lithium ore supplier. We offer the best prices for our buyers. PACKAGING & DELIVERY Packaging Details: LUMS/Chips Port: Lagos Apapa Port, Nigeria Bags: 50 kg Container: 20 ft Lead time: Quantity (metric tons) 20 MT/Month 60MT/Month Lithium time (days) 30 Days 30 Days CHEMICAL COMPOSITION ANALYSIS OF LITHIUM ORE Ingredient Percentage Lithium oxide (Li2O) 8% Alumina (Al2O3) 27% Silicon dioxide (SiO2) 64% Other minerals
SABIC MD131-1000, SABIC 2300-7301, SABIC 1000-7101, SABIC 1000-1000MC and SABIC 2200-100
TECHNICAL SPECIFICATION DATA SHEET: PROPERTY TEST ASTM TEST METHOD API @ 60 F 30- 45 ASTM D-1298 Sulfur (wt%) max 0.8 ASTM D-4294 BS &W % max 2.0 Paraffins (vol. %) 40 -70 ASTM D-2789M Naphthenes (vol. %) > 25 ASTM D-2789M Organic Chloride(ppm) < 1.0 ASTM D-4929 Organic Nitrogen max (ppm) 500 ASTM D-4629 Microcarbon Residue (MCRT) 2.0 Max ASTM D-4530 Light ends C2 â?? iC5 5 % Max Total Acid Number, mg KOH 0.8 ASTM D-664 Metals by ICP ASTM D-5708 Vanadium
COVID protection - More liquid protection - Tough, robust and abrasion - resistant - Breathable - Quality control to exceptionally high standards
Manufacture for COVID maximum usage. - Disposable - Durable - Maximum protection - This product complies with COVID standards - Hight breathability and prevents sweating - Suitable for hospitals, labs and COVID usages.