Automotive ,service equipment,hand tool,consumable material and special tools
waterv well machine - rotary table systyem - 1200 meter capacity
Wellhead drilling spool 11" x 3k - 13 5/8" x 3koil well api 16a driling spool 11" x 3k - 13 5/8" x 3k overview of the drilling spool 11" x 3k - 13 5/8" x 3k the 11" x 3k - 13 5/8" x 3k drilling spool is used to connect with bop for oilfield drilling work.The wellhead drilling spool is made of alloy steel and heat-treated. It is used on the oil and gas well which is with a pressure of less than 105mpa. It is tested according to api 16a specificationbefore shipping to be used safely.The 11" x 3k - 13 5/8" x 3k spool applies to drilling high pressure oil and gas well, the connecting of the by passage of the spool with the valves and pipes will play not only a role of blowout and choking , but also a role of connecting the bop with the wellhead. installation and maintenance of wellhead drilling spool* being used when connecting with the bop and the casing head.*.The steel ring grove should be cleaned before installation.*.Tighten studs averagely of connecting the spool with the bop. specification of the wellhead drilling spool 11" x 3k top flangebottom flange11"2000psi (279.4mm14mpa)11"2000psi (279.4mm14mpa)11"2000psi (279.4mm14mpa)13-5/8"2000psi (346.1mm14mpa)11"3000psi (279.4mm21mpa)11"3000psi (279.4mm21mpa)11"3000psi (279.4mm21mpa)13-5/8"2000psi (346.1mm14mpa)11"3000psi (279.4mm21mpa)13-5/8"3000psi (346.1mm21mpa)11"5000psi (279.4mm35mpa)13-5/8"3000psi (346.1mm21mpa) wellhead drilling spool 11" x 3k - 13 5/8" x 3koil well api 16a driling spool 11" x 3k - 13 5/8" x 3k
Technical specifications Overall dimensions mounted: lg 8.1 mx 2, 7 mxh 2m Built entirely of galvanized steel chroming. Vertical stroke 1170 mm Longitudinal slide stroke 7000 mm Cross slide stroke 1300 mm Total weight 650 kg (depending on engine) All movements are ball bearing. The blade shaft is mounted on two conical roller bearings. Trolley wheels are easily replaceable steel 380 v three-phase electric motor Petrol engine briggs & stratton Safety blade front and rear Simultaneous vertical displacement of the assembly by a single crank Accident all items can be replaced or repaired, beams, frames, truck, etc .... Sawing capacity Logs: maximum diameter of 1.4 m to 2 m and 6 m length maximum Timber: 25 cm x 25 cm (26 cm x 26 cm optional) Quarter sawn: 24 or 26 cm wide Volume of daily flow: from 6 to 12 cubic meters of wood sciépendant as sawing continues on the other station. It allows to increase the daily capacity by eliminating the time-sawing between two logs.) A portable sawmill ecopro2® includes: A sawmill with capacity 25 cm x 25 cm x 6 m A tilting system (this equipment allows to remove the waste and to position a new log without risk of collision logs / lumber mill in the open position while sawing continues on the other station. It increases daily capacity eliminating the time-sawing between two logs.) A sharpener (sharpener helps sharpen the saw teeth without removing the blade.) (+ link to the video) A toolbox A blade diameter 630 mm
Technical Data K5-320 K5-400 Planer Max. Planer Width mm 320 400 Work Table Length mm 1560 1920 Max. Planing Thickness mm 4 4 Cutter Shaft Speed R/min 5200 5200 Number Of Cutters 3 3 Cutter Shaft Dia. mm 86 86 El. Motor Power kW 2.2 3 Thicknesser Max. Planer Width mm 320 400 Work Table Length mm 550 690 Max. Planing Thickness mm 180 220 Max. Planing Heigh mm 3 3 Cutter Shaft Speed R/min 5200 5200 Number Of Cutters 3 3 Feeds m/min 8 8 El. Motor Power kW 2.2 3 Boring Device Table Dimensions mm 400/250 (500) 400/250 (500) Longitudinal Travel mm 100 (150) 100 (150) Cross Travel mm 100 (150) 100 (150) Vertical Travel mm 100 (150) 100 (150) Max. Drill Dia. mm 16 16 Drill Speed R/min 5200 5200 Spindel Moulder Spindle Diameter mm 30 (50) 30 (50) Spindle Speed R/min. 6000 6000 Vertical Stroke of Spindle mm 130 130 Max.Ttool Diameter mm 170 170 Dimensions Of Worktable mm 850 / 450 850 / 450 El. Motor Power kW 2.2 2.2 Circular Saw Saw Blade Diameter mm 300 300 Saw Blade Speed R/min. 3700 3700 Max. Depth Of Cut mm 85 85 Dimensions Of Worktable mm 850 / 450 850 / 450 Spindle Dia. mm 30 30 El. Motor Power kW 2.2 2.2 or 3 Tenoning carriage Dimensions of worktable mm 450/750 450/750 Machine dimensions Net weight of the machine Kg 540 580 Length mm 1600 2000 Width mm 1140 1700 Height mm 1000 1100
Technical characteristics FU 251M FU 301 FU 321M FU 361 FU 401 Table size mm 250x1120 300x1250 320x1350 360x1500 400x1600 “T” slots – number x size mm 3x14 5x14 5x18 5x18 5x18 Table swivel – left and right (º) 45 45 45 45 45 Longitudinal table travel - manual mm 820 950 1000 (1250)* 1150 (1250)* 1250 - automatic mm 800 930 980 (1230)* 1130 (1230)* 1230 Cross table travel - manual mm 280 320 360 360 360 - automatic mm 260 300 340 340 340 Vertical table travel - manual mm 410 410 460 460 460 - automatic mm 390 390 440 440 440 Max. Distance from table top to spindle axis mm 440 440 490 490 490 Spindle nose taper ISO 40 40 50 50 50 Number of spindle speeds 18 18 18 18 18 Spindle speed range rpm 40-2000 (50-2500)* 40-2000 (50-2500)* 32-1600 (40-2000)* 32-1600 (40-2000)* 32-1600 (40-2000)* Number of table feeds 18 18 18 18 18 Table feed rate - x,y mm/min 12.5-630 (16-800)* (20-1000)** 12.5-630 (16-800)* (20-1000)** 12.5-630 (16-800)* (20-1000)** 12.5-630 (16-800)* (20-1000)** 12.5-630 (16-800)* (20-1000)** - z mm/min 5-262 (7-334)* (8-415)** 5-262 (7-334)* (8-415)** 5-262 (7-334)* (8-415)** 5-262 (7-334)* (8-415)** 5-262 (7-334)* (8-415)** Table rapide traverse mm/min 2500/1040 2500/1040 2500/1040 2500/1040 2500/1040 Main motor power kW 4 5.5 7.5 7.5 7.5 Feed motor power kW 1.5 1.5 2.2 2.2 2.2 Machine weight kg 1975 2025 2850 2900 2925 * - option Note: All the milling machines could be manufactured with control of the movement of the axes by joystick, and frequency adjustment of the feeds
Pathfinder10 is drill rig for coring and drilling, . It can be built on different frames such as regular skid frame, wheel, truck and hydraulic crawler. It has hydraulic regulated spindle to control speed of rotation between 53 rpm to 897 rpm step less. The rotation head can be swung aside for hole cleaning or grouting equipment. Pathfinder10 has automatic hydraulic synchronization system between chuck and rod holder to handle the rods. It has hydraulic jacks at the top of the feeding frame for stabilization. Pathfinder10 has also optional accessories such as hydraulic mud mixer, water flow meter, hydraulic mud pump (140 lt/min), high torque, shock absorbent and second rod holder. 72 rpm181 rpm
Explorer60 is full hydraulic drill rig for coring and drilling for underground galleries and surface. It can be built in different frames such as regular skid frame, three wheel trailer and hydraulic crawlers narrow or wide. Explorer60 also can be built in different feed lengths for different purposes. It has hydraulic regulated spindle to control speed of rotation between 166 rpm to 1000 rpm step less. It can be designed either with electrical engine or diesel engine. The rotation head can be swung aside for hole cleaning or grouting equipment. Explorer60 has automatic hydraulic synchronization system between chuck and rod holder to handle the rods. For stabilization it has hydraulic jacks at the top of the feeding frame. Explorer60 has also optional accessories such as larger wire line hoist, cathead or two step hydraulic water pump.
Explorer30 is the small hydraulic drill rig for coring and drilling for narrow tunnels, underground galleries and surface. It has small built so that easy to install and carry. It has hydraulic regulated spindle to control speed of rotation between 350 rpm to 2200 rpm step less. It can be operated with one person. It can be designed either with electrical engine or diesel engine. The rotation head can be swung aside for hole cleaning or grouting equipment. Explorer30 has automatic hydraulic synchronization system between chuck and rod holder to handle the rods.
Rocker34 wagon drill rig Rocker34 is designed for drilling blast holes with dth hammer. Rocker34 has crawler for the difficult ground conditions, strong construction, easy maneuver capability. MAST AND FEED SYSTEMFeed Length4,1 m13 ft Feeding Force0 - 27 kN Pulling Force47,5 kN Drilling Angle22° - 90° POWER UNITBrandDEUTZ TypeF4L912 Number of Cylinder4 cylinders Cylinder Volume3,7 lt Power51 kW - 70 Hp Rev.2300 rpm Engine TypeDiesel CoolerAir HYDRAULIC SYSTEMFirst Pump160 bar27 cc /rev. Second Pump130 bar19 cc / rev. Auxiliary Pump180 bar19 cc / rev. Hydraulic Oil CoolerAir2024 K - 0,110 kW - 12 V ROTARY UNITSpeed133 rpm Toruque1185 Nm SUPPORT JACKSMovement UnitTrack / max speed 2,9 km/h Leverages of Jacks2 units of Hydraulic Leverages Cylinder Stroke150 mm m Weight2.830 kg ADVANTAGES
Planer Plate dimensions400 x 2300 mm Front plate length 1110 mm Rear license plate size 1110 mm Max. Planing length 18 mm Trench slope angle0-45 Blade qty 4 Top spindle speed 4000 rev / min Top shaft diameter 105 mm Saw tray Plate dimensions 550 x 800 mm Circular saw blade diameter 350-400 mm Shaft diameter 30 mm Tray spindle speed 3600 Drill Plate dimensions 270 x 480 mm Longitudinal motion 170 mm Transversely action 135 mm Vertical movement 160 mm Drill diameter 20 mm Machine Motor force 4 hp Dead weight 850 kg.
Vdd5 wagon drill rig (rubber whell driller) Technical characteristics General information Engine38 kw Weight2180 kg Feed frame Length5, 00 m Stroke4, 10 m Push force0 - 25 kn Pull force50 kn Drilling Drill speed0 - 120 cm/min (it may change due to ground.) Drilling diameter2, 5'' - 4'' / 63 mm - 102 mm Drilling depth50 m Rotation unit Drive engine75 rpm Torque1000 nm Oil cooler2024k – 0, 110kw – 12v Fuel tank capacity70 liters Oil tank capacity250 liters Advantages Vdd5 has hydraulic pull and push force. Vdd5 works with dth hammer. Vdd5 is moving with 3 wheel hydraulic traction. Vdd5 can be controlled with electrical joystick. Three wheel traction system of vdd 5 can be chosen as demanded. (only front, only back or free) Vdd5 is manufactured with high quality materials to maintain power and lifetime. Vdd5 provides easier and faster drilling with enhanced pull and push force and rotation. Vdd5 has a large volume of oil tank and oil cooler; therefore, the oil is used more efficient and long time. Vdd5 can drill 76, 89, and 100 mm of hole sizes. Vdd5 can drill with giving from 22 degrees to 90 degrees of drilling position. Vdd5's drilling vibration is minimized with the help of balancing pistons. Özanadolu sitesi 682. Sokak no: 25-27 Ývogsan-ankara-turkey tel: +90 312 394 47 24 faks: +90 312 395 62 07
e equipment was manufactured by Jeffrey Rader AB, Sweden in 1995 and it is in very good operational condition. It consist of two heavy duty rolls with removable profilied surfaces which rotate towards each other and presses overzised wood chips between the profiles. Roll drives 2 x 110 kW / 1500 rpm connected with two gearboxes. Hydraulic pump 7.5 kW, capacity 220 m3/h wood chips. The equipment was manufactured by Jeffrey Rader Inc, Sweden in year 1995, manufacturers type is DynaYield 80-300 and it is in good operational condition. The Chip Conditioner consists of two heavy duty rolls with removable profiled surfaces. They rotate towards each other and pull the oversize chips between them. The profiled surfaces are aligned so that the pyramid apexes on one roll travel in the valleys of the apexes on the adjacent roll. With normal oversize wood, the Conditioner typically generates less than 1% fines and 3% pins The normal application for the Chip Conditioner is in a chemical pulping process, processing the oversize materials by fissuring the wood chips parallel with the grain to allow the cooking liquors to penetrate the chip, and allow the oversize chip to cook as an acceptable size chip. Another application is in a thermo-mechanical pulping process (TMP), as a preconditioning An important feature of this machine is its ability to handle small portions of tramp without going off-line. With the so called Dynagage Conditioner, the dynamic roll is allowed to move away from the static roll, and once the tramp is through the unit, the roll automatically moves back to the proper set point without shutting down the flow and together with slow rotation speed enable were low down time and maintenance costs. Roll distance movements are made with a hydraulic system build on the equipment and controlled by 3 position sensors More information on requests, for spam protection please introduce yourself properly. Technical data: Model: RDY 80-300 Manufacturing year: 1995 Capacity (throughput): 220 m3/h loose wood chips Press roll diameter: 915 mm Roll length: 2440 mm Roll motors: 2 x 110 kW / 1500 rpm / 690 V – 50Hz Press distance between the rolls: 2.2 mm Gearboxes: 2 x Kipo Benzler TV 512 Hydraulic pump: Rexroth 200 bar with Mecman syliders Electric motor for hydraulic pump: ASEA 7.5 kW Weight: 33 000 kg Length: 5083 mm Width: 2550 mm Height: 2400 mm.
We would like to offer you following used lathes: 1.Heavy duty lathe kramatorsk 1a660 (1250x6300mm), price 45.000 USD 2.Heavy duty lathe kramatorsk 1a665 (1600x12000mm), price 160.000 euro.
We would like to offer you following used lathes: 1) Vertical lathe kolomna 1540F1 (max.Dia 4000mm), price 200.000 USD. 2) Vertical lathe Sedin 1l532 (max.Dia 3150mm), price 100.000 USD .
Sliding table saw Technical data Fixed table size mm 1580-800 Fixed table size cut mm 1280 Fixed table from floor mm 850 Carriage diemension mm 680 Lateral table saw mm 1150 Vlade arbor diameter mm 30 Max. Depth of cut mm 250 Blade tilting 45'-90' Max. Depth of cut mm 65 Motor power hp 4 Motor speed rpm 1500-3000 Blade speed rpm 3000-6000 1300*1000*900mm 450kg
Tailor chalk. 12 box, 1200 pieces in one package.
Air water post model a 107779w Application - gas stations - fleets - car dealers - large trucks - tractors - garage shops - rentals - bike shops - balls -one colum housing for water and air connections -two reels : one for the air house and another for the water house -with tyre pressure gauge -with water pistol for the radiators and etec. -an original barking systems for the houses -one metal casing The operation with the air-water post can be used only with fitted casing. Technical information Features air water House length (in meters) 10 10 + house interior (in mm.) 6 6 House service connection R 3/8ö male R +ö male Maximum working pressure 20 bar 20 bar Net weight 65 kg 65 kg Gross weight 85 kg. 85 kg. Dimensions with packing ( in mm.) 60x60x1630 60x60x1630 Net weight 65 kg 65 kg Gross weight 85 kg. 85 kg.
Drill pipe, tricone bit, down the hole hammer s andbit, chain wrenches, drill bit,
Industrial carbon brushes
