EN590 was introduced to coincide with the development of new emissions standards across the European Union. The overall goal has been to reduce the sulphur content of diesel fuel. Sulphur had been used as a lubricant in the fuel. Its role is taken by special additives in ULSD. Since 2007, diesel that conforms to EN590 has been referred to as Ultra Low Sulphur Diesel (ULSD) in the European Union. The phrase Ultra Low Sulphur Diesel is governed by different standards in other parts of the world. EN590 describes the physical properties that all automotive diesel fuel must meet if it is to be sold in the European Union, Croatia, Iceland, Norway and Switzerland. The EN 590 had been introduced along with the European emission standards. With each of its revisions the EN 590 had been adapted to lower the sulphur content of diesel fuel since 2007 this is called ultra low sulphur diesel as the former function of sulphur as a lubricant is absent (and needs to be replaced by additives). The quality of European diesel fuels is specified by the EN 590 standard. While these specifications not are mandatory, they are observed by all fuel suppliers in Europe. Automobile diesel en 590 is intended for application in diesel engines. Diesel motor fuel quality meets the requirements of European Standard EN 590. For operation in the conditions of a temperate climate following marks of fuel diesel automobile EN 590 are offered: Grade C limiting filterability temperature -5 C; Grade D limiting filterability temperature -10 C; Grade E limiting filterability temperature 15 C; Grade F limiting filterability temperature -20 C. The entire volume of produced diesel fuel quality meets the requirements for fuels for vehicles of Euro 4 and Euro 5. Low sulfur content in diesel EN 590 reduces emissions of sulfur oxides into the atmosphere, which is especially important for for inhabitants of big cities.
D6 is also be known as Residual Fuel Oil and is of high-viscosity. This particular fuel oil requires preheating to 220 - 260 Degrees Fahrenheit. D6 is mostly used for generators. D6 is a type of residual fuel, mainly used in power plants and larger ships. The fuel requires to be preheated before it can be used. It is not possible to use it in smaller engines or vessels/vehicles where it is not possible to pre-heat it. D6 is its name in the USA. In other parts of the world it has other names. Residual means the material remaining after the more valuable cuts of crude oil have boiled off. The residue may contain various undesirable impurities including 2 percent water and one-half percent mineral soil. D6 fuel is also known as residual fuel oil (RFO), by the Navy specification of Bunker C, or by the Pacific Specification of PS-400 Recent changes in fuel quality regulation now require further refining of the D6 in order to remove the sulfur, which leads to a higher cost. Despite this recent change, D6 is still less useful because of its viscosity as well as that it needs to be pre-heated before it can be used and contains high amounts of pollutants, such as sulfur. Since it requires pre-heating, it cannot be used in small ships or boats or cars. However large ships and power plants can use the residual fuel oil. The price of D6 diesel traditionally rises during colder months as demand for heating oil rises, which is refined in much the same way.In many parts of the United States and throughout the United Kingdom and Australia, d6 diesel may be priced higher than petrol. D6 Diesel Standards and ClassificationCCAI and CII are two indexes which describe the ignition quality of residual fuel oil, and CCAI is especially often calculated for marine fuels.
Automobile diesel fuel (EN 590) Grade E (winter), recommended for use at ambient temperatures up to minus 15 C (limiting filterability temperature). Diesel fuel EN 590 (EN 590) Grade E is obtained from petroleum refined products and is intended for use as automotive fuel for diesel engines of cars and trucks. Diesel fuel meets the requirements of the international standard EN 590/2000 and is characterized by a low content of sulfur, aromatic hydrocarbons and a high cetane number, which leads to an overall reduction in sulfur oxide emissions, a decrease in the amount of particulate matter in exhaust gases and the formation of deposits in the fuel system of cars and heavy vehicles, reducing exhaust smoke and is the key to good starting properties of the fuel during cold start of the engine. The oil refining industry produces diesel fuel in accordance with GOST 305-82 of three grades: L - summer, used at ambient temperatures above 0 C; 3 - winter, used at temperatures up to -20 C (in this case, winter diesel fuel should have a stagnation
product Description : These Products are Exported with Stringent Adherence to Standard Russian Export Specifications with Respective GOST. Price of product ( USD price or FOB price) : Product will be priced in USD$ Based on an Appropriate PLATTS INDEX or a FIXED Price and the Agreed Upon Shipping Method. The Price will be Mutually Agreed to by Buyer and Seller Product origin : Russian Federation Key Specifications/Delivery/Logistics : 1. Certification SGC or Equivalent 2. Payment Terms = Letter of Credit ( Details to be agreed upon by Buyer and Seller 3. Delivery Time = Varies by Destination 4. Port of Loading = TBD Minimum Order Size & Contract Term : Minimum Monthly Quantity = 100,000 MT X 12 Month Contract Required with R & E up to 120 Months
We supply Diesel Fuel 100 ppm EN 590 on FOB and CIF Incoterms. FOB available from Rotterdam, Houston, and Fujairah. Occasionally we have spot deals. PRODUCT ORIGIN: Kazakhstan Contract directly with the Refinery. Send us an LOI to info@odissiglobal.com The EN 590 standard is the European diesel fuel specification for low sulphur content diesel and describes the properties diesel fuel must meet if it is to be used in automobiles. This specification of diesel is the grade required by a diesel-engine road vehicle (DERV) and the majority of agricultural machinery.
L/C ,DLC, SBLC payment is accepted, NO upfront, pre-payment. Minimum Order Quantity is 100k/mt if spot. We are one of the most precise on non-sanctioned supply due to strict requests of our clients. We are in direct colloboration with reputable sellers,resellers,retailers,manufacturers and also well known refineries within our portfolio. Both as buyer and seller according to the necessarities in our partnerships.
(EN590) 10 PPM/50PPM Origin: Kazakhstan The detailed specification: Meets all International Standards Total Spot quantity order: 100,000MT The price and discount: - FOB ROTTERDAM AND CIF OTHER COUNTRY: DISCOUNT $50 PER MT FROM NWE PLATTS - CIF ASIA: DISCOUNT $70 PER MT FROM SINGAPORE PLATTS Shipment: - TANK TO VESSEL ROTTERDAM PORT or DESTINATION PORT as per conditions in Seller`s FCO Payment terms: As agreed per attached Seller`s SCO / FCO and PROCEDURE, via MT103 Payment Procedure: According to the terms of the contract, to be mutually agreed upon by Buyer & Seller. Inspection: SGS for Quantity and Quality, at embarkation port, DIP TEST
We sell Oil and Gas Products Wholesale Ultra -low sulphur diesel ( EN590) Liquified natural gas Liquified petroleum gas Ultra -low sulphur diesel ( EN590) Light cycle oil Petroleum coke Eastern Siberia-pacific ocean oil ( espo) Jet fuel A1 Mazut Aviation fuel A-1 & Jp54 Bitumen Base oil Diammonium phosphate Naphtha Ultra Low Sulfur Diesel EN590,DIESEL D2,DIESEL VIRGIN OIL D6
CIF EN-590 10ppm Diesel -12 Month Contract Production Procedures: Product: EN590 Diesel 10ppm Origin: Dubai Delivery: CIF to any safe world port MOQ: 100mt CIF Transaction Procedures: 1. Buyer issues LOI/ICPO. 2. Seller issues Draft Sales Purchase Agreement Contract and for Buyer\'s review and signing. 3. Buyer and Seller sign Sales Purchase Agreement Contract and the Buyer will send Draft Banking instrument verbiage for review. 4. Seller sends partial POP to Buyer via email: (a) Statement of Availability of Product (b) Seller's Irrevocable Commitment to Supply (c) Product Passport (d) Certificate of Product Origin (e) ATSC (Authorization to Sell and Collect) 5. Buyer sends the Final Draft of LC/SBLC for Sellers approval. 6. Buyer\'s Bank Swift the irrevocable, operative, transferable, divisible, confirmed and fully Funded Documentary Letter of Credit IRDLC to the Seller\'s bank. 7. Seller sends the full POP and 2% Performance Bond to Buyer\'s bank. 8. Shipment commences as scheduled in the contract and upon arrival of the cargo at the discharge port and after SGS/Q&Q, or equivalent inspection, immediately Buyer\'s Bank releases the Total Value of the Shipping to Seller\'s Bank within 48 hours (two banking days) by MT103 against shipping documents specified. 9. Seller pays all intermediaries involved in the transaction as per IMFPA within 48 hours. Notes: 1) Seller will allow transferable sblc/dlc and non-transferable sblc/dlc as a finance instrument. 2) Buyer must submit Loi/icpo to start engagement with our seller.
Available products: D2, D6, EN590, DIESEL 10PPM & 50PPM, JET A1/JP54, CRUDE OIL, BITUMEN, MAZUT M100, Copper. Safe procedure and long-term cooperation - that is our motto. As an experienced team based in Berlin, with direct contacts to refineries and direct clients, I and my team ensure a smooth procedure. For us, the customers are the focus of everything we do. To be successful, we need to know what our buyers need. We want to ensure that we offer our buyers added value with our solutions. We meet our commitments and meet our deadlines and goals. Send us LOI so that we can start processing the order. If you have any questions please do not hesitate to contact us! Available products: -JET A1 -JET JP54 -Diesel D2, -EN590 10 PPM, -Diesel D6, -BIODIESEL -Mazut M100 -Bitumen -Crude Oil -Copper
We sell Oil and Gas Products Wholesale Diesel gas d2 gost 305-82 Liquified natural gas Liquified petroleum gas Ultra -low sulphur diesel ( EN590) Light cycle oil Petroleum coke Eastern Siberia-pacific ocean oil ( espo) Jet fuel A1 Mazut Aviation fuel A-1 & Jp54 Bitumen Base oil Diammonium phosphate Naphtha Ultra Low Sulfur Diesel EN590,DIESEL D2,DIESEL VIRGIN OIL D6 We are an oil and gas company Agents, Facilitators and Mandate; we source crude oil for Refineries and large volume buyers, and other petrochemicals like AGO, LPFO, PMS, DPK and other Russia product origin listed below for the upstream and downstream sectors consumption. 1) D2- Gas Oil (Diesel) Lo.2-62 Gost 305-82 , Quantity- 50,000mt 500,000mt For Cif And Fob, Spot And Contract Basis. 2) Jp54 Aviation Kerosine Colonial Grade 54 Russia Origin, Quantity- 1,000,000bbls 8,000,000bbls For Cif And Fob, Spot And Contract Basis. 3) Aviation Turbine Fuel Jet A-1 Quantity- 1,000,000bbls 8,000,000bbls For Cif And Fob, Spot And Contract Basis. 4) Bitumen Quantity 50,000mt 500,000mt, Cif And Fob, Spot And Contract Basis. 5) M100 Mazut 100 Gost 10585-99 And 10585-75, Quantity- 50,000mt 500,000mt, Cif And Fob, Spot And Contract Basis. 6) Liquid Petroleum Gas.Gost 20448-90, Quantity 50,000mt 500,000mt, Cif And Fob, Spot And Contract Basis. 7) Liquified Natural Gas, Quantity 50,000mt 500,000mt, For Cif And Fob, Spot And Contract Basis. 8) Russia Sn 150 Base Oil, Quantity - 5,000mt 50,000mt, For Cif And Fob, Spot And Contract Basis. 9) Russia Sn 500 Base Oil, Quantity 5,000mt 50,000mt, For Cif And Fob, Spot And Contract Basis. 10) En590 Biodiesel, Quantity 50,000mt- 500,000mt, For Cif And Fob, Spot And Contract Basis. 11) Automotive Gas And Oil (Ago), Quantity 50,000mt 500,000mt, For Cif And Fob, Spot And Contract Basis. 16) Russia Export Blend Crude Oil (Rebco), Quantity 1,000,000bbls 6,000,000bbls, For Cif And Fob, Spot And Contract Basis.
Diesel
Light Cycle Oil (LCO) is a diesel boiling range product from Fluid Catalytic Cracking Units (FCCUs). FCCU is responsible for the production of petrol, LPG and Light Cycle Oil (LCO). There are various ways of economically upgrading LCO, which include hydrotreating, high pressure hydrocracking for full conversion of LCO into Naphtha and a more optimized partial conversion hydrocracking process. It can be used in susch industries as Agrochemical, Crude Oil, Petrochemicals, Petroleum Products.
Mazut-100 is a fuel oil that is manufactured to GOST specifications, for example GOST 10585-75/99. GOST is the Russian system of standards. Mazut is almost exclusively manufactured in the Russian Federation, This product is typically used for larger boilers in producing steam since the BTU content is high. The most important consideration when grading this fuel is the sulfur content, which can mostly be affected by the source feedstock. For shipment purposes, this product has a high viscosity which drastically affect whether it is able to be pumped, shipping has unique requirements. Mazut is much like Number 6 Oil, and is part of the products left over after gasoline and lighter components are evaporated from the crude oil. The main difference between the different types of Mazut-100 is the content of sulphur. The grades are represented by these sulfuric levels: - "Very Low Sulphur" is mazut with a sulphur content of 0.5% - "Low Sulphur" is a mazut with a sulphur content of 0.5-1.0% - "Normal Sulphur" is a mazut with a sulphur content of 1.0-2.0% - "High Sulphur" is a mazut with a sulphur content of 2.0-3.5% - Very Low Sulfur mazut is generally made from the lowest sulfur crude feedstocks.
D6 is a type of residual fuel, mainly used in power plants and larger ships. The fuel requires to be preheated before it can be used. It is not possible to use it in smaller engines or vessels/vehicles where it is not possible to pre-heat it. D6 is its name in the USA. In other parts of the world it has other names. Residual means the material remaining after the more valuable cuts of crude oil have boiled off. The residue may contain various undesirable impurities including 2 percent water and one-half percent mineral soil. D6 fuel is also known as residual fuel oil (RFO), by the Navy specification of Bunker C, or by the Pacific Specification of PS-400. Recent changes in fuel quality regulation now require further refining of the D6 in order to remove the sulfur, which leads to a higher cost. Despite this recent change, D6 is still less useful because of its viscosity as well as that it needs to be pre-heated before it can be used and contains high amounts of pollutants, such as sulfur. Since it requires pre-heating, it cannot be used in small ships or boats or cars. However large ships and power plants can use the residual fuel oil.
We can supply ULSD 10PPM from FOB Jurong, Singapore. QTY 100,000MT per month. Contact us for further details and prices.
Commodity: EN590 / JetA1 / D6 Price Term: $580.00 / $88 / $0.99 Delivery Terms: FOB Dip & Pay, FOB TTT, Tank Takeover, and Tank to Vessel (TTV)
Parameter Unit Appearance: Clear and bright, free from visible sediment and water. Colour: 2.5 max Odour: Merchantable Density @ 15C g/ml: 0 820 min 0 835 max Cold filter plugging point Winter C (*): -15 max Summer C (*): -5 max Cloud point Winter C (*): -5 max Summer C (*): +3 max Flash point (PMCC) C: 56 min Cetane number: 51 min Cetane index: 46 min Viscosity cst @ 40C: 2.0 min 4.5 max Sulphur % Wt: 0 001 max Copper corrosion 3 hr @ 50C: class I Micro carbon residue: Residue wt on 10% bottoms: 0 30 Ash % Wt: 0 01 max Particulate matter mg/kg: 24 max Water mg/kg: 200 max Distillation C % Vol Rec @ 250 C: 65 0 max % Vol Rec @ 345 C: 85·0 min 95% Vol recovered C: 360 0 Oxidation stability mg/100ml: 2·5 max Polycyclic aromatic hydrocarbons (%): 11 max Lubricity, Corrected water scar: 460 Diameter @ C
Powered by:zh60(2.0hp) Votage:230v Rate output:650w Surge output:750w Frequence:50hz Dc:12v-8.3a Dimension:380x315x325 0, 04cbm
Ultra Low Sulfur Diesel EN590,DIESEL D2,DIESEL VIRGIN OIL D6 We have the below available products ready for supply. Contact us for immidate transaction 1) D2- Gas Oil (Diesel) Lo.2-62 Gost 305-82 , Quantity- 50,000mt - 500,000mt For Cif And Fob, Spot And Contract Basis. 2) Jp54 Aviation Kerosine Colonial Grade 54 Russia Origin, Quantity- 1,000,000bbls 8,000,000bbls For Cif And Fob, Spot And Contract Basis. 3) Aviation Turbine Fuel Jet A-1 Quantity- 1,000,000bbls 8,000,000bbls For Cif And Fob, Spot And Contract Basis. 4) Bitumen Quantity - 50,000mt - 500,000mt, Cif And Fob, Spot And Contract Basis. 5) M100 Mazut 100 Gost 10585-99 And 10585-75, Quantity- 50,000mt 500,000mt, Cif And Fob, Spot And Contract Basis. 6) Liquid Petroleum Gas.Gost 20448-90, Quantity 50,000mt- 500,000mt, Cif And Fob, Spot And Contract Basis. 7) Liquified Natural Gas, Quantity 50,000mt 500,000mt, For Cif And Fob, Spot And Contract Basis. 8) Russia Sn 150 Base Oil, Quantity - 5,000mt - 50,000mt, For Cif And Fob, Spot And Contract Basis. 9) Russia Sn 500 Base Oil, Quantity - 5,000mt - 50,000mt, For Cif And Fob, Spot And Contract Basis. 10) En590 Biodiesel, Quantity 50,000mt- 500,000mt, For Cif And Fob, Spot And Contract Basis. 11) Automotive Gas And Oil (Ago), Quantity 50,000mt - 500,000mt, For Cif And Fob, Spot And Contract Basis.