Polyurethane Multi-Purpose Construction Joint Sealant DESCRIPTION ITLS PU 50 is a single component polyurethane based elastomeric sealant which cures under the effect of atmospheric humidity to form a flexible and resistant joint with very good adhesion on most materials. APPLICATION ITLS PU 50 can be used for bonding and caulking different materials used in the general industry : concrete, wood, aluminium, most lacquered metals, polyester, glass, stone, etc.
DESCRIPTION Cement Filler is used for exterior coating on the tiles, steel plate, a smooth surface or a low porosity material to combine the old surface and the new one. FEATURE * Water-based formulations of two special adhesive. * For tiles, steel, a smooth surface or a low porosity of the material surface ?¯ etc. * With waterproofing, impervious, weather resistance, freeze-thaw characteristics. * Can be used both on wet and dry surfaces. * With good adhesion. APPLICATION * To adhere and mix old concrete surface and new concrete surface * Can be used to adhere indoor and outdoor old cement walls, fiber cement board, tile, concrete, colored steel board, asbestos and various green compartment plates etc. WORKING PROCEDURE 1 All surfaces need to be clean, free from dust, rust, white birch and either grease. In addition, the concrete could be moistened but not with floating. 2. Coating CA-003M by brush, roller or spray on the substrates. The coverage would be 4 ~ 7m ² per kilograms which depends on the situation of porous and roughness of the substrates. 3 All the tools can be cleaned by water.
DESCRIPTION CC-601SP is a two component, Epoxy system with High Chemical Resistance and High Bond Strength. The epoxy may be applied as a primer for most High End Industrial coatings, like Epoxies, PU. CHARATERISTIC * Easy apply * Low odor * High bond strength * Abrasion resistant * Chemical resistant APPLICATION * Concrete coating * Cement
Description CA-003W Waterproof Agent is a high-grade liquid additive that gives the dual benefits of providing significant improvement in workability along with reduced water absorption. The addition of CA-003W to a mortar mixture enhances the plasticity of the mixture by creating a â??ball-bearingâ?? effect. At the same time, the microscopic capillaries are rendered discontinuous, thereby impeding the flow of liquid through them, and finally reducing the permeability of the mortar. CA-003W contains special polymers that reduce formation of shrinkage cracks. The improved cohesion provides lower rebound loss supplemented by a greater coverage. The increase in coverage can be up to 20 %. This makes significant cement savings possible. The spreading and smoothening is also made much easier. The efficiency of labor is increased, and plastering can be done in a single operation. CA-003W provides the mortar with efficient,reliable and durable damp proofing against acute rains, ground water moisture as well as environmental humidity. Thus the use of CA-003W provides significant benefits, while keeping plastering economical.
DESTRIPTION HYPERCOAT 570 is a pre mixed, pre coloured water based, slip-resistant UV stable coating with excellent performance against wear and weathering, therefore providing a rejuvenated fresh and safe surface coating that is suitable for internal and external use. HYPERCOAT 570 has excellent hot tyre resistance and forms a hardwearing finish. HYPERCOAT 570 is recommended for both commercial and residential use. Most common applications include tennis court repair, walkways, playgrounds and similar recreational areas around domestic, municipal, educational and commercial buildings. It is also suitable for stair treads, decks, balconies, ramps and is easily repaired or recoated after thorough cleaning.
DESCRIPTION CA-001 is a high performance acrylic emulsion additive for cement and sand mixes for waterproofing purposes. It is soft, elastic and transparent after drying. FEATURES * High Solid Contents. * Soft, elastic and transparent after drying and thereby reducing the incidence of crack formation. * Improve workability, water resistance and compressive strength for concrete. * Mixes easily with cement and sand mixes. * Suitable for interior and exterior uses. APPLICATIONS CA-001 can bond well to masonry, concrete, cement and sand backing, and various porous materials.
DESCRIPTION CA-002 is an Acrylic Polymer emulsion, especially used to improve the physical properties of cement. It can be mixed with water at any ratio. AREA OF APPLICATIONS * Repair mortar for concrete areas * Industrial flooring * Bonding agent for new to old concrete * As cement grout additive * As water based primer * For making two component tile adhesive * As adhesion aid for skim coat materials
DESCRIPTION ITLS LD5 is a high performance liquid deadener for panel vibration damping and noise control. The exceptional vibration damping properties are complimented by fast drying , ease of use, environmental friendliness and low flammability. ITLS LD5 is a thixotropic paste and is specially designed for trowel, pour, brush, roll-on and air-gun spray applications. Once dry the cured film is UV resistant and water resistant. ITLS LD5 is a light weight product. The dry film is light in weight without compromising the high performance. Consequently, this material is recommended for weight sensitive applications eg. aircraft, marine and automotive applications. ITLS LD5 effectively reduces resonant vibration. Vibration energy is absorbed within the material and converted to heat. In addition to vibration damping, it also increases substrate transmission loss as a result of the reduction of panel coincidence and panel resonance effects.
DESCRIPTION CC-301 is 1-K aromatic moisture curing PU adhesive. It can be used as a waterproof primer for cement. CC-301 has excellent bonding strength, weather resistance, hydrolysis resistance after fully curing about 3 days. OPERATION 1. Put CC-301 onto the cement and then use a roller to coat on the cement. 2. When first coating has become tack-free (about 1 hour), the second coating can be applied. 3. After fully curing (about 8-24 hours), the top coating can be applied.
DESCRIPTION A Torch on waterproofing membrane for multi layer application; following project evaluation this membrane may be used as an intermediate layer in fairly large professional waterproofing application with top quality membrane on stable surfaces or in temporary applications such as retaining walls to provide protection against ascending moisture on under-flooring surfaces. The COMPOUND used in ITLS CP-109 membranes contains distilled bitumen, polypropylene polymers and stabilizing aggregates and is the result of many years of research to obtain the best performance for specific roofing applications. The use of REINFORCEMENT in reinforced glass mat or non woven polyester stabilized with glass fibers gives ITLS CP-109 good dimensional stability and excellent mechanical properties in this class of polyester membranes for standard applications. Top FINISH in silica sand, non-woven polypropylene or self-protecting natural and colored slate chips disseminated uniformly and firmly anchored; 3/4mm version with embossed finish, all others are smooth. Both BOTTOM finish with torch off polyethylene sheets. PRODUCT PLUSES ï¼? guaranteed by more than 10 years in the field; low cost high performance; wide product range.
DESCRIPTION HYPERCOAT-518 is a premium, semi-thixotropic, liquid-applied, highly permanent elastic, cold applied and cold curing, one component synthetic rubber membrane used for long-lasting waterproofing. HYPERCOAT-518 is solvent based, cured by reaction with ground air moisture. And itâ??s semi-thixotropic for use in sloped surfaces. APPLICATION â?? Concrete Roof, balconies, terraces and verandas â?? Wet areas (under-tile) in bathrooms, kitchens, balconies, auxiliary rooms, etc. â?? Pedestrian and vehicular traffic decks â?? Green roofs, flowerbeds, planter boxes â?? For repair old bitumen felts, asphalt felts, EPDM and PVC membranes and old acrylic coatings. â?? Waterproofing and protection of concrete constructions like bridge-decks, tunnels, stadium stands, car parks, etc. Product properties â?? Long lasting performance with acidity and alkaline â?? Good resistant with oil, bitumen, wax â?? Strong adhesion with metal and concrete substrate â?? One component products, easy to apply and suitable for various tooling â?? Elongation more than 700%, tensile strength more than 70kgf/cm2, â?? Penetration strength more than 25kgf/cm2, tear strength more than 40kgf/cm
Description CC-500 Dura-Shine is one component, aliphatic, UV resistant polyurethane based topcoat membrane. Product cures with the humidity and produces a transparent film and by this way it provides excellent adhesion over the entire surface. Feature Resistant to UV, exposed sunlight and chemicals When applied, it forms as seamless membrane without joints Product keeps its mechanical features over a temperature span of 40 to 90 degrees Celsius Use Area Roof terraces balconies and verandas Industrial floor coatings Stadium, car parks Stones, marble and ceramic surfaces Coverage Consumption of each layer: 0.1-0.15 kg/m2 Minimum two coats should be applied Total consumption: approx. 0.2-0.3 kg/m2 Recoating: Do not exceed 48 hours between each coats. Application must be repeated if this time is exceeded
DESCRIPTION a premium cement based finish skimcoat which contains selected filler, additive and polymer used for smooth finishing to uneven concrete wall & ceiling. After dry STARCOAT CN have a excellent adhesion to the substrate, better impact resistant, no powdery, no cracks, smooth and ready to be painted with water based wall paint. Easy to use, good workability and have a long pot life and correction time even at the outdoor applications. USES IN APPLICATIONS 1. Cement Based Wall Plaster. 2. Concrete Wall, Column & Ceiling 3. Precast Concrete & Concrete profile 4. Internal & External. ADVANTAGE * Light, good workability and sanding properties. * No cracks and hair cracks. (depends on background) * Smooth surface, solid and no powdery. * Can be painted or finished with wallpaper directly after dry in minimum 24 hours * without using PVA putty to leveling up & filling uneven rough surface. PRODUCT SPESIFICATIONS 1. Main Binder : Portland Cement & Polymer 2. Filler : Limestone 3. Color : GREY and WHITE. 4. Mixing Ratio : 7 - 8 litres of water per 25 Kg bags. or 28 - 32 % water demands. 5. Coverage : 1.25-1.3 Kg/m2/mm or 19m2/25 Kg/mm thickness average 7.5m2/25Kg for 2-3mm thickness 6. Thickness : 2mm thickness/coat 4mm for 2 coats and 6mm for 3 coats. 7. Pot Life : approx. 60 minutes SURFACE PREPARATION * The substrate must be clean and free from grease and loose particles. Recesses should be pre-patched and levelled where appropriate. * Porous and absorbent substrates must be pre-wetted prior to application of Starcoat CN finish coat.
DESCRIPTION STARCOAT PL, is fine grade cement based finish plastering skimcoat which contains selected filler and additive used for smooth finishing to uneven wall cement based plaster and ceiling. After dry STARCOAT PL have a good adhesion to the substrate, no cracks, smooth, no dust on the surface and ready to be painted with water based paint. Easy to use, good workability and have a long pot life and correction time even at the outdoor applications. USES IN APPLICATIONS *Cement Based Wall Plaster. *Precast Concrete. *Concrete Profile & Concrete Ceilings *Internal & External. ADVANTAGE *Light, good workability and sanding properties. *No cracks and hair cracks. (depends on background) *Smooth surface, solid and no powdery. *Can be painted or finished with wallpaper directly after dry in minimum 24 hours without using PVA putty to leveling up & filling uneven rough surface. PRODUCT SPESIFICATIONS 1. Main Binder : Portland Cement & Polymer 2. Filler: Limestone 3. Color: GREY and WHITE. 4. Mixing Ratio : 7 - 8 litres of water per 25 Kg bags. or 28 - 32 % water demands. 5. Coverage: 1.25-1.3 Kg/m2/mm or 19m2/25 Kg/mm thickness average 7.5m2/25Kg for 2-3mm thickness 6. Thickness: 2mm thickness/coat 4mm for 2 coats and 6mm for 3 coats. 7. Pot Life: approx. 60 minutes SURFACE PREPARATION 1. The substrate must be clean and free from grease and loose particles. Recesses should be pre-patched and levelled where appropriate. 2. Porous and absorbent substrates must be pre-wetted prior to application of Starcoat PL finish coat.
DESCRIPTION AS-600 is a high-solid, solvent-based polyurea coating. Itâ??s also formulated with pure aliphatic resin and contains UV filters, remaining unaffected by the sunlight and adverse weather conditions. It cures fast providing quick tack free time (1-2 hours), allowing most projects to be completed within one day. CHARATERISTIC * Fast drying and fast curing * Brushable * Abrasion and mechanical stress resistant * Chemical resistant (in diluted acids-alkalis, car oils, petroleum, etc) APPLICATION AREAS * Warehouse ramps, garages, terraces, parking areas * Outdoor and indoor stores, industrial shop floors * Outdoor laundries, gas station, etc..
DESCRIPTION HYPERCOAT-688 is the range of high performance, seamless, cold-applied liquid waterproofing membrane. CHARATERISTIC 1. Quick and easy to apply. Single pack, liquid applied waterproofing membrane. 2. Excellent hydrolysis resistance 3. Still can curing when apply on the moisture surface without observed water. 4. The middle layer of the tile, the top coating or each cement-based finished surface. APPLICATION 1. Indoor: Bathroom, kitchen & terrace 2. Outdoor : Roof, floor joint, parapet and wall.
DESCRIPTION Power Screw adhesive is one of ITLS new range of power adhesives developed to give a cost effective and high adhesion performance. It is very low in odor and free of aromatic solvent for use indoor and outdoor. It was designed for use by both the home handy man and professionals. Power Screw adhesive which consists of tough elastomeric rubber, tackifying resins and Light hydrocarbon solvent. Power Screw can be used in most common construction materials. The substrates are timber, plywood, MDF, particle board, hard board, plaster board, cementitious fibrous board, concrete, ceramic, aluminum, ,mild steel, galvanized iron sheet, back of mirror (on wall only). FEATURES *Unique user friendly, highly pseudo-plastic and non runny characteristic making it TRULY easy to use on vertical wall and ceiling. * Extremely easy to extrude from cartridges in winter making it an all round product for use in all seasons. * Gap filling because of its higher solid content and especially it is highly pseudo-plasticity (soft smooth by stiff, non-sagging) property. * Flexible but tough for use around home and in construction * Easy on hand to extrude and apply due to its unique consistency. *Easy to spread our adhesive evenly and thinly due to its soft buttery consistency. * Broad application for most timber based, cementitious substrates, ceramic and most common metallic construction products. * Printable when dried. * Help to spread out pressure on bonded materials thereby prevent localized stress leading to adhesion failure.
Description CS-613 is a multipurpose water-based epoxy sealer/putty/adhesive. Itâ??s developed for filling seam, gap between Calcium Silicate board. It is environmentally friendly which does not pose health hazard to user and dwellers. The best part is how easy it can be cleaned with just water. Itâ??s easy to mix even by hand due to our innovative water-based technology. Features / Benefits *Paintable easily with water-based coating; can be painted after 1 day without work delay hence reduce time and save money. * Easy to use: Compatible with damp surface, time is saved in waiting for it to dry up; Washable with water including tools. Best to wash as soon as possible before it hardens. * Smooth to tool with trowel; Non-sagging characteristic making it easy to use on vertical wall and ceiling. * Stronger adhesion due to higher amount of binders used. * High solid by volume; 100% water resistant when cured. * Low odor/ solvent free/ VOC free, it does not pose health hazard to user and dwellers.
Rubber/silicon Rubber Injection Molding, Vacuum Compression Molding And Other Types Of Molding. .
BESTCHEM product are applicable:Textile, coating, plastic, color drawing...,related products. :good coverage, high elastic, soft hand feeling, good washing fastness....etc Water base Plastisol ink Silicon ink Binder Additive Pigment