Roasted Guar Korma has been developed as a product free of antinutritive factors with balanced Amino Acid Profile. Suitable for Poultry, Swine, Ruminant and Aquaculture. Processed with heat and steam, inactivates harmful trypsin inhibitor which indirectly enhances protein and Amino acids digestibility in the product resulting in increased productivity of livestock and poultry. This process also reduces gummy substance by hydrolysing glactomannan and heat breaks cell walls resulting in higher digestibility of Guar Korma. The anti-nutritive trypsin inhibitor is present in both Soybean and Guar seed, but gets inactive when processed into Soybean meal and Guar meal respectively. We have two qualities of Roasted Guar Korma namely ULTRA and PREMIUM In Roasted Guar Korma ULTRA, the minimum protein content is 48 % and in Roasted Guar Korma PREMIUM, the minimum protein content is 55 %. The other nutritional and Amino Acid values of ULTRA and PREMIUM Roasted Guar Korma are listed below:- • Higher percentage of Crude Protein (CP) • Free From Aflatoxins • Higher Digestibility Index, due to the removal of anti-nutritive factors • More desirable and balanced Amino acid Profile • Higher Energy content and fat percentage • Lower percentage of less digestible Fibre • Higher Palatability, complete elimination of characteristic bean odour and taste. • Low content of Total Volatile Nitrogen (TVN) • Free flowing, uniform fine particle size with good fat and water binding ability NUTRITIONAL VALUES ULTRA PREMIUM Protein 48% – 50% 55% – 60% Metabolize Energy 2550 KCal/Kg 2700 KCal/Kg Moisture Less Than 8% Less Than 6% Fiber 6% – 8% 4% – 5% Fat 5.00% 5.00% Ash/ Sand Silica Less Than 2% Less Than 1% Calcium 0.55% 0.55% Phosphorus 0.68% 0.68% Available Phosphorus 0.19% 0.19% Urease Activity Less Than 1% Less Than 1% Pepsin Digestibility 85.00% 85.00% Trypsin Inhibitor Less Than 1 Less Than 1 Aflatoxins NIL NIL Salmonella NIL NIL E.Coli NIL NIL
Shubhlaxmi Industries is a manufacturer and exporter of Quinoa seeds to across the world. These seeds are very nutritive and we have been successful in keeping its nutrition intact. In today's world it is known as Super Food. The botanical name of Quinoa Seeds is Chenopodium quinoa and it belongs to Amaranthaceae Family. These are tiny seeds and mostly white to red or black in color. They are origins of Peru and Bolivia, India. The herbaceous plant is cultivated for its use of seeds. They are pronounced as 'keen waah'. They have their own rich taste. Quinoa seeds can be added in vegetable salad to make healthier. It can be an option for rice which is healthy and high calorie free. They are used as a stuffing in some of the veg and non veg recipes. Quinoa seeds are innovatively used for making cookies and pancakes. They can be dry roasted to make health snack bars. Quinoa seeds are very healthy. They are packed with protein, fiber and essesntial amino acids. They contain rich anti oxidants in them. They are gluten free and super rich in fiber content. It has low Glycemic Index which means it controls blood sugar. Use of the seeds make us healthier. Specification HS Code 10085000 Purity Levels : 99/1 Sortex Color : Cream White Moisture ; 8% Max Ash : 4.5%max Contrast Gains : 2%max E-coli : Absent Aflatoxin (b1+b2+g1+g2) as Per Eu Standards Salmonella : Absent/25gms Packing : 5/10/25/50 Kg Net Pp. & Brand Packing Quality Assurance : Sgs, Geo-chem Loading Capacity : 20mt In 20'fcl
FH SERIES OF PRODUCTS: FH products are Pure nonionic derived the endosperm of guar polysaccharide (Cyamopsos tetragonolobus). The products are unique with ultra-high viscosity with fastest hydration characteristics as shown in Figure 1 below. Also, when added with other drilling components, to seawater, a KCl solution or other aqueous system, the product suspension disperses readily without lumping, even under low-shear conditions generating most of its full viscosity within just a few minutes. PRODUCT COMPATIBILITY: FH series of products are compatible with most of the chemicals and auxiliaries used in drilling operations. However, the products are not compatible with Arabic and Crystal gums. Also, in presence of borates they form elastic gel. PRODUCT APPLICATIONS: FH series of products are natural, high viscosity, fast hydrating non-Newtonian hydrocolloids with suitable cross linking components in diesel slurries and are versatile for continuous mix applications, where extremely fast hydration and subsequent viscosity development is required. They are excellent viscosifiers, stabilizers, thickeners and suspending agent for use in oil-drilling, workover fluids and several other oilfield applications like hydraulic fracturing, oil well stimulation, mud drilling, oil well capping, flocculent and liquid shoring etc. The product is used as a surfactant; synthetic polymer and deformer ideally suited for all rheological requirements of water based and brine based drilling fluids. Specifications:- PRODUCT : FH-35 FH-38 FH-42 CAS No. : 9000-30-0 9000-30-0 9000-30-0 Granulation : FINE FINE FINE APPEARANCE : OFF WHITE POWDER MOISTURE : 8% Max. 8% Max. 8% Max. PROTEIN (N X 6.25) : 5.0% Max 5.0% Max 5.0% Max ASH : 1.5% Max. 1.5% Max. 1.5% Max. ACID INSOLUBLE RESIDUE (A.I.R.) : 3% Max. 3% Max. 3% Max. CARBOHYDRATE (incl gum by difference) : 82% Min 82% Min 82% Min pH (1% Solution) : 5.5 ? 6.5 5.5 ? 6.5 5.5 ? 6.5 VISCOSITY : (0.48% Product in 2% KCL Sol. 2.5 mins mix @1500 RPM in waring blender) Fann 35sa Viscometer at 300 RPM, 25�C 3 Mins : 35 3 Min:38 3 Mins : 42 5 Mins : 37 5 Mins : 39 5 Mins : 43 30 Mins : 39 30 Mins : 42 30 Mins : 45 60 Mins : 40 60 Mins : 43 60 Mins : 47
All Other Products Green Millet Bajra Chickpeas Bay Leaf Psyllum Husk & Powder Quinoa Seeds Moringa Seeds/Leaf/Powder Shubhlaxmi Industry is the manufacturer and exporter of Chickpea/Kabuli Chana globally. The beans are assorted well, cleaned and hygienically packed. Chickpea has nutritive values & rich in protein and fiber as well.,which well maintained while mechinally processing to sort the best chickpea to serve best of it. The botanical name of Chickpea/ Kabuli chana is Cicer arietinum-garbanzo and it belongs to Fabaceae Family. They are considered as legumes. They are light brown, looks like Hazelnut in shape, small and hard. It has minimum fat content and thus considered as healthy. Chickpeas mostly used as boiled or a paste can be made to be used in different cuisines. Chickpeas have tasty flavor. They can be used in making curry which is a very popular dish in India. Moreover it can be used in making healthy salad along with vegetables. Middle Eastern countries make Humus out of Chickpea paste that is applied over Pita bread to make Falafal rolls. Some of the other varieties include Three Beans Salad Chickpea with boiled Rice Sprouted Chickpea Salad Patty or Cutlets and many other mouth watering delicacies. Even, Chickpeas have some healthly properties as Its regulated blood sugar. They contain ample amount of Folate and Vit. B9. They are good for heart and lower cholesterol level. It is a food having low Glycemic Index hence it is very good for health. Specification Chickpeas (Kabuli) Hs Code : 07132000 Count Per Oz. 42-44 44-46 46-48 58-60 60-62 75-80 Size 12mm 11mm 10mm 9mm 8mm 7mm Moisture 10-12% Max 10-12% Max 10-12% Max 10-12% Max 10-12% Max 10-12% Max Admixture 0.5% Max 0.5% Max 0.5% Max 0.5% Max 0.8% Max 0.8% Max Total Defect % 4.2% Max 4.2% Max 4.2% Max 6.5% Max 6.5% Max 7.5% Max Weeviled Seeds% 0.2%max 0.2%max 0.2%max 0.5%max 0.5%max 1%max Free From Live Weevil Packing : 15/25/50 Kg Net Pp Bag Quality Assurance : Sgs, Geo Chem Origin : Madhyapradesh, Gujarat, Rajasthan Loading Capacity : 24mt in 20'fcl
Shubhlaxmi Industries is a manufacturer/processor and exporter of supreme quality of Moringa seeds, Moringa Powder & its oil. Moringa seed is an important part of Moringa tree, because it contain large amount of protein and iron in it. Moringa seed is present inside the Moringa Pods. Moringa seed is like round shaped. From one Moringa pods we can get more than 5 number of seeds. We Process and supply multi grade/variety like pkm-1 moringa cultivation seeds, pkm-2 cultivation seeds, km-1 seeds, moringa traditional seeds, moringa oil seeds, moringa medicinal seeds, moringa pharma grade seeds. Its botanical name is Moringa oleifera, its only genus in the plant family Moringacae. Its widely harvesting southwestern India.,Each & Every part of this plant is used in variety of applications including Food, personal & health care, agriculture,dye, water purification and many more. Its significant & high valued source of vitamin-B, vitamin-C, & provitamin-A as beta-carotene, vitamin-k, proteins & other essential nutrients. Its greenish leaf cooked & used as we use Spinach in Various Delicious Dishes, & also used in soups & sauces by crushing in powder. Its Immature seeds pods, also called Drumsticks, which used in south asian dishes by parboiling & cooked in curry. Its seeds mostly consumed like roasted peanuts, peas & nuts, which consists high level of vitamin-C & vitamin-B. Its also yield oil around 40%, used as edible oil, called Ben oil, because of its higher concentration of behenic acid. Its refined oil is much clear & odorless. As medicinal value of moringa oleifera had been suggested by traditional medicine, further clinical testing is required to explore more benefits. Characteristics of pkm -1 SEED variety Seed propagated Medium, dwarf stature Pods are 60-70 cm long with 6.3 cm girth weighing 120g Bears 220-250 fruit per tree The estimated yield is 50-54tonnes/ha Suitable for ratoon crop Low incidence of insect pest and disease Suitable for varied soil types (freely drained)in tropical plains Specification Moringa Seeds/leaf/powder Hs Code : 12119099 Specification/ Variety Pkm-1 Seeds Leaf T Cut Leaf Powder Oil Moisture : 8-10% Max 7-10% Max 10% Max 0.20% Total Ash Value : 14% 15% Max 12% Max 0.01% Purity Level : 98-99% 98-99% 98-99% 100% Foreign Material : 1% Max 1% Max Absent Absent Apperance : Browinsh Green Emrald Green Yellowish Salmonella In 25g Absent Absent Absent : Na E-coli Cfu/g : Absent Absent : 20 Max Na Quality Assurance : Sgs,geo-chem, Spice Board Moq 1ton Packing : 10/25/35/50 Kg, Pp Bag/jute Bag/cartoon Origin ; Tamil Nadu
19th Century Easy Chair with Walnut Frame
We at GREENLAND FRESCO procure Peanuts in the most professional way and always ensure that fresh and healthy products are delivered to our clients. We keep pace with the latest technology and market requirements to ensure stability & sustainability towards fulfilling the clients demand. We have built a cost-effective and reliable supply chain to deliver Java & Bold varieties of Peanuts in one click. We maintain aflatoxin level & moisture content at minimal level. Peanuts are processed at processing plants to obtain the required specifications specified by our clients. Specifications of Bold / Java / Blanched Bold / Blanched Java Peanut kernels : - Type - Peanut kernels Peanuts counts per Ounce - 38/42, 40/50, 50/60, 60/70, 70/80 Origin - India Admixture - 1% max Oil content - 42% - 48% max Foreign Material - 0.50% max OR 1% max Moisture - 7% max OR 8% max Aflatoxin - Aflatoxin negative 5/10 PPB Gross Wt. per Bag - 10/15/25/50 Kgs Packaging Material - New Jute Bags Load Ability : One 20" FCL can load 19 MTS or 380 Bags of 50 Kgs New Jute Bags One 20" FCL can load 19 MTS or 760 Bags of 25 Kgs Vacuum Bags New vacuum pack inside and outer layer with PP woven bags 25 Kgs Gross Specifications of Peanuts in Shell Bold / Java : - Type - Peanuts in shell Bold : HPS- Ground nuts Peanuts bold shell - 18/22, 20/24, 22/26 Counts/Ounce Origin - India Moisture - 6-8% Max Admixture - 1% Max Imperfect - 5% Max Aflatoxin(B1+B2+G1+G2) - 5-10 ppb (as per clients specifications) Packing - In Strong Jute Bags of 30 Kgs Net/Gross Each One 20" FCL can load 12-14 MTS One 40" FCL can load 19-20 MTS Health Benefits 1. Peanuts have a strong nutritional Profile 2. Peanuts can reduce the risk of Heart disease 3. Peanuts are excellent source of plant based protein, fiber and many key vitamins and minerals. 4. Peanut consumption reduces the risk of weight loss and obesity 5. Peanut consumption reduces the risk of colorectal cancer
65% Cotton / 35% Polyester
29 x 29 x 11 cms(+/- 2cms) 5 Kg Cocopeat Blocks A Grade, Washed, Low EC Produced in our Own Facility
Head Diameter: Normal Length: OEM Material: Iron,low carbon steel Type: Concrete Nail Shank Diameter: 2.0mm-5.2mm
Magnesia Bricks Description Magnesia Bricks are alkaline refractory materials. These products have over 90% magnesium oxide content and adopt periclase as the principal crystalline phase. Magnesia Bricks can be divided into two categories of Burnt Magnesia Bricks and Chemical Bonded Magnesite Brick. They have excellent performance of superior high temperature mechanical strength and volume stability. Magnesia Bricks can service in the high temperature of 1750.. They are ideal products for glass furnace application. Magnesia Bricks Features: It is a kind of alkaline refractory product with periclase as main phase magnesite-alumina spinel clinker as basic material. the product has such characteristics as good temperature vibration, good strength and volume stability in high temperature. Magnesia Bricks Application Basic open-hearth furnace for steelmaking Electric furnace bottom and wall Permanent lining of oxygen converter Non-ferrous metal metallurgy furnace Hyperthermia tunnel kiln Lining of rotary cement kiln Heating furnace bottom and wall Regenerative chamber of glass furnace Magnesia Bricks Properties High Refractoriness Good alkaline slag erosion resistance High apparent initial softening temperature Good thermal conductivity High thermal expansion Magnesia Bricks Manufacturing Process Burnt Magnesia Bricks are manufactured with magnesite clinker as the raw material and fired in the high temperature of 1550~1600 after smashing, burdening, mulling and molding. High-purity products can be fired in the temperature that over 1750. Chemical bonded magnesite brick is produced with certain chemical bonding through mixing, molding and drying.
Insulation Bricks
Refractory Fire Brick
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Ramming mass is commonly used in metallurgy, building materials, non-ferrous metal smelting, chemical, machinery and other manufacturing industries. Ramming mass is widely used in non-core intermediate frequency furnace and core induction furnace. As an intermediate frequency furnace ramming material, refractory ramming is applied to melt gray cast iron, nodular cast iron, malleable cast iron, vermicular cast iron, and cast alloy steel; to melt carbon steel, alloy steel, high manganese steel, tool steel, heat resistant steel, stainless steel, molten aluminum and its alloys; to melt red copper, brass, white brass, bronze and its alloys, etc. Induction furnaces are used for melting cast iron, mild steel and various alloy steels in foundries and making of steel in mini steel plants using sponge iron The refined high silicon, low iron quartz sand and quartz powder are selected and the fused quartz sand is added as the refractory material., with no slag, no crack, damp proof, convenience of repair, and the corrosion resistance, thus greatly improving the furnace service life span and the economic benefit.. Silica ramming mass can safely be used up to an operating temperature of 1600 deg C. Since it expands very little, it is superior to both alumina and magnesia refractories to resist thermal shocks Acid ramming material is the premixed ramming mass of the lining material. The acid ramming mass is used to smelt a series of metal materials such as ordinary steel and carbon steel. The lining practice best suited to a particular furnace depends upon the capacity and design of the furnace, operation practice adopted during making of a heat, and furnace output.
METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor
