-MPORE UF Membranes are made from top grade PVDF material, which provides excellent durability and resistance against breakage, even with periodic cleaning procedures to remove fouling. -Blending technology from Germany MPOREú¡Higher strength Patented blending technology improves the tensile strength and pressure resistance of UF membrane, which can adapt the turbid operational state and cleaning condition. It solves problems of other PVDF membranes being with low tensile strength and pressure resistance. -UF PVDF membrane has higher filtration finenessú¡Better permeate water quality With a nominal pore diameter of 0.03 ª¦m, UF technology effectively removes pathogens, most viruses and bacteria. In addition, the membraneí»s high porosity allows high flux operation at a given transmembrane pressure (TMP). -Highly hydrophilic membrane materialú¡ Advanced technology of modification Patented technology of modification improves hydrophilicity of UF membrane so as to increase its ability of anti- fouling.
Duct-Baling-Press TypeBP 4000 V / 19,5 This press is excellent qualified for low-cost disposal of various kinds of waste material. The press can work under continuous feeding and will work very profitable. The press operates with a fully automatic system of bale binding device. Depending on the high compression, bales of pulp, paper, compounds, blister packs and foils can reach a bale package density up to 400 kN. Extremely rugged construction with high reliability. The feeding will be handled in accordance to the local requirements. The control will be fully automatic by photoelectric barrier. Technical Data: Drive:..................................19,5 kW/400 V/50 Hz Pressure:...............................400 kN/m¦ Volume/stroke:.....................1,0 m¦ Cycle time:............................28 sec Feed opening:......................1350x820 mm Bale dimensions:..................800 x 900 x 600 ..............................................1.200 mm No of tightening wires:..........4 Press length:.........................5750 mm Press width:..........................2050 mm Press height with funnel:......1925 mm press height complete:.........2360 mm Weight:..................................6100 kg
new Engine complete 81KW (110 PS) Opel-No. 55576751 including spare parts: Clutch-No.: 55576088; Starter No.: M002T86272; high pressure pump -No.: 294000-1003; Turbocharger Nr.: 789533-2; Injectors, flywheel, fit in: OPEL Astra H (1.7 Ltr.) CDTI, Bj. 2007-2014; Astra H GTC (1.7 Ltr.) CDTI, Bj. 2007-2010; Astra J GTC (1.7 Ltr.) CDTI, Bj. 2011-2015; Astra J (1.7 Ltr.) CDTI, Bj. 2009-2015; Zafira B (1.7 Ltr.) CDTI, Bj. 2008-2015 available Qty: 100 pieces
MERCEDES BENZ A-Claas (W176) ; B-Claas (W246, W242), C-Claas (W204) CLS (C218, C219, X218, CLA 200 CDI (X117), Bj. 2015-2019; GLA (X156), Bj. 2013- E-Claas (W212, A207, C207, S212), M-Claas (W166) Dieselmotor, 4 Zylinder (short running) 3 km; 100 kW; Euro 6; with Alternator, AC Compressor, slide valve (electronic throttle gas cooler), exhaust manifold, exhaust gas cooler, high pressure pump, Turbocharger, vacuum pump (mechanical), glow time output stage, 2-mass-flywheel, this engines was short running - takte off from tested car -
We are manufacturer specialize in Agricultural products, 90% of our goods exported abroad. European and Asia are our mainly export market. we have the following advantages if u choose us: 1:Health: we pay much attention to our products' quality, all of our goods are Natural Grown food, non-public hazard 2:Cheap price: in order to enlarge abroad market, we can offer you best price.our price are cheaper than other supplier 3:High Quality: our products' Purity can up to >99% , Moisture
High purity Cobalt metal pieces, element 27 sample, 2 grams 99,99% in glass vial with label. Pure cobalt metal element. Cobalt is one of the transition metals with chemical symbol Co and atomic number 27. It is solid and silvery-grey at normal pressure and temperature, it's very strong to cut. Cobalt metal is another dangerous metal, do not touch without latex gloves. We suggest this element at various purity like 99,9% and 99,99% in a 7 mL or 5mL glass vial with about 2 cm of diameter. We usually use cobalt pellet or cobalt electrolytic flakes both very shiny.
Made in: europe Sex: women and men Season: all seasons Packaging: 46 pcs (kg) We are a leading german wholesaler company in the remaining stock sector. The content is identical. Our customers get our products as we advertise it in our packing list. Only the sizes, colors and models differ. The benefits we provide to our customers from our head office in germany are high service quality, reliability and professionalism. With our expertise with remnants we support our customers. Our business processes are developed to minimize the amount of work and satisfy our customers. Postskriptum gmbh Export-import agency
Complete with power LED ( 50000 h). Very high light intensity 1212 lm, light colour 6500K daylight white. Beam spread 20° Max. Lighting distance: 68m / 1 Lux Protection degree IP69K. Dimensions: Ø 130mm, depth 50mm. Floodlight model DOX is distinguished by a monolithic aluminium die-cast body extremely robust and compact, containing 12 led chips housed in a sealed, waterproof and maintenance free, compartment. The body is mounted on a steel fixing bracket through a coil, helping absorption of vibrations and also allowing small aiming adjustments. Most relevant peculiarity of model DOX is the ability to operate under a really flexible supply ranging from 9V to 30V DC allowing use with batteries, small generators and also in combination with solar photovoltaic panels. The floodlight is well apt for lighting tasks on boats and and industrial vehicles with a power consumption of only 18W and a powerful light beam. Use: DOX is a led work light with a great efficiency and minimal power consumption requiring a very low voltage power supply and with an high IP69K protection degree. DOX is an ideal floodlight for use in all motor vehicles both civil (boats, cars, camper vans...) or industrial (ships, cranes, earth moving machines, bulldozers, fork lifts...) and, able to function with a flexible supply range from 9 to 30V DC that allow usage also with energy coming from photovoltaic solar panels. DOX peculiarities allow a secure use in all situations were electrical safety needs require or suggest to employ low voltage. Usage of power led sources with a lifetime rated for more than 50.000 hours and very high efficiency makes DOX a searchlight of relevant performance. The floodlight employs 12 1,2W monochromatic cool white leds, with a colour temperature of about 6500 °K, for a total power of 18W. DOX also guarantees a limited surface temperature and a cold emitted light beam, with absence of U.V. emissions. On demand DOX can be supplied for use at line voltage (220/240 V). In such case is required an external 350 mA constant current power supply to be set separately, as the waterproof model available as an accessory. Construction: die-cast aluminium body and antiscratch coated polycarbonate protection screen. DOX is also equipped with a cable tail and a malefemale couple of waterproof connectors for a quick power connection. The floodlight is supplied hermetically sealed as no maintenance is required.
Product Description : * Negin , High quality type In the category of all red saffron in terms of the colour power, taste and aroma Sargol * Ranking with types of saffron. Negin is in second place after Super Negin , In terms of color and aroma. Key Specifications/Special Features : Other Names : Negin , Sargol Negin , Negin B Type : All Red Average length of filaments : 17 mm In Accordance With : ISO 3632 , National standard 259-1 & 259-2 Packing Ability: From 0.2 gr to 500 gr,Customized packing Phytosanitary certificate: Yes Certificate of Origin: Yes Shelf Life : 2 Years Price: Based on quantity Origin : IRAN All standards certificates and Lab analysis are available Too many other designs of packings are available
Product Description : * Sargol or Sargol Momtaz , one of the middle quality .In the category of all red saffron in terms of the colour power, taste and aroma . * Sargol, middle quality of saffron with some powder and broken * Ranking with types of saffron , Sargol Momtaz is in third place after Negin in terms of color and aroma. This type has high crocin and Safranal yet. "Key Specifications/Special Features : Other Names : Sargol , Sarghalam , Sargol Momtaz , Momtaz Type : All Red Average length of filaments : 14 mm In Accordance With : ISO 3632 , National standard 259-1 & 259-2 Packing Ability: From 0.2 gr to 500 gr, Customized packing Phytosanitary certificate: Yes Certificate of Origin: Yes Shelf Life : 2 Years Price: Based on quantity Origin : IRAN All standards certificates and Lab analysis are available Too many other designs of packings are available
Introduction: We are trading and suppliers of copper scraps.We supply various copper scraps such as copper wire scraps,copper millberry scrap etc.We offer the copper scraps at very competitive prices and the delivery is prompt. We pack the copper scraps loose in 20 or 40 ft containers or as per buyers request. We also supply copper cathode, aluminum ingot, aluminum alloy ingot, zinc ingot. Product advantage: (1).High quality with best price (2).Well reputation (3).Factory with strong supply ability (4).Prompt shipment Usage: Electrical, light industry, machinery, building industry, national defense industry. Copper Scrap is industry a important sources of the raw materials All kinds of can be recycled Recycling waste production with copper. Name Copper wire scrap (Millberry) 99.78% Item Standard (%) Results(%) Purity (%) â?¥99.78 99.9 Carbon 0.03 0.03 Coblet
About Meltblown Nonwoven Melt blown is a one step process to make fabrics from polymer. The thermoplastics chips are fed through main dosing units & these chips are melted by means of the extruder. This extruder then extrudes the melt, which is then filtered & metered at a constant rate. This filament comes out from a single raw of spinneret orifice. It has a self bonding property but for coagulation & for better random laying hot air flow is provided. The web generated is immediately passes among the Spunbond webs followed by pre-bonding rolls & finally through calendar for thermal bonding. The main purpose of melt blown fabric is to provide barrier property for the liquid. Sometimes the treatment like antistatic or hydrophilic are given to the fabrics & after drying the fabrics are wound in the winder as a roll form. Unique characteristics such as water repellence or permeability or UV stability can be obtained by incorporating additives to the raw materials or applying different agents to the fabric. Characteristics of Meltblown fabrics are: The main desired characteristics expected for melt blown nonwoven fabrics are: Adjustable Pores And Capillary Structure Excellent barrier properties Filament size 1 -3 �?�µm High Elasticity High Filtration capability Isotropic formation- this means that the fibers are randomly distributed in the machine direction (MD) and cross-machine direction (CD). Large Area-to-weight ratio Self-bonding The weight of the melt-blown fabrics in gram per square meter (GSM) should range from 4 g/m2 to over 1000 g/m2. Very good thermal insulation for apparel application Weak tensile properties Wicking Properties Application of spun-bond nonwoven fabrics: Sanitary and Hygiene: Sanitary napkins, Baby diapers and Incontinence diapers Medical and Surgical: Gowns, Face masks, Caps, Drapes, etc Other Miscellaneous Applications: Filtration Material, Agriculture, Oilsorbents Hot-melt adhesives Headliners, etc
About Meltblown Nonwoven Melt blown is a one step process to make fabrics from polymer. The thermoplastics chips are fed through main dosing units & these chips are melted by means of the extruder. This extruder then extrudes the melt, which is then filtered & metered at a constant rate. This filament comes out from a single raw of spinneret orifice. It has a self bonding property but for coagulation & for better random laying hot air flow is provided. The web generated is immediately passes among the Spunbond webs followed by pre-bonding rolls & finally through calendar for thermal bonding. The main purpose of melt blown fabric is to provide barrier property for the liquid. Sometimes the treatment like antistatic or hydrophilic are given to the fabrics & after drying the fabrics are wound in the winder as a roll form. Unique characteristics such as water repellence or permeability or UV stability can be obtained by incorporating additives to the raw materials or applying different agents to the fabric. Characteristics of Meltblown fabrics are: The main desired characteristics expected for melt blown nonwoven fabrics are: Adjustable Pores And Capillary Structure Excellent barrier properties Filament size 1 -3 �?�µm High Elasticity High Filtration capability Isotropic formation- this means that the fibers are randomly distributed in the machine direction (MD) and cross-machine direction (CD). Large Area-to-weight ratio Self-bonding The weight of the melt-blown fabrics in gram per square meter (GSM) should range from 4 g/m2 to over 1000 g/m2. Very good thermal insulation for apparel application Weak tensile properties Wicking Properties Application of spun-bond nonwoven fabrics: Sanitary and Hygiene: Sanitary napkins, Baby diapers and Incontinence diapers Medical and Surgical: Gowns, Face masks, Caps, Drapes, etc Other Miscellaneous Applications: Filtration Material, Agriculture, Oilsorbents Hot-melt adhesives Headliners, etc
About Meltblown Nonwove Melt blown is a one step process to make fabrics from polymer. The thermoplastics chips are fed through main dosing units & these chips are melted by means of the extruder. This extruder then extrudes the melt, which is then filtered & metered at a constant rate. This filament comes out from a single raw of spinneret orifice. It has a self bonding property but for coagulation & for better random laying hot air flow is provided. The web generated is immediately passes among the Spunbond webs followed by pre-bonding rolls & finally through calendar for thermal bonding. The main purpose of melt blown fabric is to provide barrier property for the liquid. Sometimes the treatment like antistatic or hydrophilic are given to the fabrics & after drying the fabrics are wound in the winder as a roll form. Unique characteristics such as water repellence or permeability or UV stability can be obtained by incorporating additives to the raw materials or applying different agents to the fabric. Characteristics of Meltblown fabrics are: The main desired characteristics expected for melt blown nonwoven fabrics are: Adjustable Pores And Capillary Structure Excellent barrier properties Filament size 1 -3 �µm High Elasticity High Filtration capability Isotropic formation- this means that the fibers are randomly distributed in the machine direction (MD) and cross-machine direction (CD). Large Area-to-weight ratio Self-bonding The weight of the melt-blown fabrics in gram per square meter (GSM) should range from 4 g/m2 to over 1000 g/m2. Very good thermal insulation for apparel application Weak tensile properties Wicking Properties Application of spun-bond nonwoven fabrics: Sanitary and Hygiene: Sanitary napkins, Baby diapers and Incontinence diapers Medical and Surgical: Gowns, Face masks, Caps, Drapes, etc Other Miscellaneous Applications: Filtration Material, Agriculture, Oilsorbents Hot-melt adhesives Headliners, etc
Powerful and safe - manufactured in Germany. Optionally with following light sources: 1) fluorescent lamp 15W - 900 lumen. Lifetime 8000 h, white light. The brightness is similar to 75w halogen light. 2) or fluorescent lamp 18W - 1200 lumen, Lifetime 12000 h, white light. The brightness is similar to 90w halogen light. 3) or with power LED lamp 15W - 1200 Lumen, Lifetime 40000 h, white light. The brightness is similar to 90w halogen light. 4) or sodium low pressure lamp LPS 18W - 1770 lumen. Lifetime 18000 h, yellow light. The brightness is similar to 120w halogen light. Solar Panel: 75W / 100W / 120W mono crystalline silicon (protecting glass, hail-proof) aprx. 25 years life duration. This modern module technology has a high degree of efficieny and allows charging also at cloudy weather. Solar battery: 12V maintenance-free power gel accumulator 12 volt. Life time: 5-8 years. Functions well under low temperature. Control: Microprocessor for automatic lamp start by light sensor, turn-off by dawn or by the adjustable timer, e.g. after. 8 hours. Over-charge and low-discharge protection for the battery. Pole: Steel hot-dip galvanized, height 500cm + 80cm for concreting. Rigid plastic case for inground-mount for the batteries, (walk-over). Size 360 x 260 x 320mm. Daily operation at dark-cloudy weather: a) Standard version: 1 day (16 hours) b) with extension kit autumn: 2 days (24 h) c) with extension kit winter: 4 days (40 h) Distance from pole to pole = Lighted area Ø aprx. 25 meter Ambient temperature: -35°C ~ +60°C Maintenance-free (only sometimes is the cleaning of the solar panel required). Included in the shipment: High-power battery, pole and lamp.
FAKT BP 5000 This press is excellent qualified for low-cost disposal of various kinds of waste material. The press can work under continuous feeding and will work very profitable. The press operates with a fully automatic system of bale binding device and a three-sided duct cross sectional adjustment device. Depending on the high compression, bales of pulp, paper, compounds, blister packs and foils can reach a bale package density up to 600 kg. Extremely rugged construction with high reliability. The feeding will be handled in accordance to the local requirements. The control will be fully automatic by a photoelectric barrier. Technical Data: Drive:...................................35 kW/400 V/50 Hz Pressure:..............................600 kN/m¦ Volume/stroke:....................1,3 m¦ Cycle time:...........................19 sec Feed opening:......................1350 x 1160 mm Bale dimensions:.................1100x750x600 .............................................1.200 mm No of tightening wires:..........4 Press length:.........................6850 mm Press width:..........................2650 mm Press height with funnel:.....2150 mm press height complete:........3700 mm Weight:..................................14600 kg Basic equipment - Touchpanel - photocell control - bale longimetry - fully automatic three-sided duct cross sectional adjustment device - free pitching device - fully automatic binding - 4 pieces wire coil stands large - 4 pieces wire bags for 40 kgs spools - electric control ready to plug in (SPS Siemens) engineering und documentation space assignment plan plans of electric control operation manual security instructions
Meltblown Nonwoven Meltblown nonwovens, the fineness fiber up to 1 m, generally 1~3m. Meltblown nonwovens has special fiber structure and unique production process, it has a wide range of applications, such as filter materials, medical materials, sanitary suppliers, sound-absorbing materials, oil-absorbing materials, thermal materials, wiping cloth and other fields. Raw Material 100% Polypropylene Color White, Black Width 10-160cm Weight 9-300gsm Grade BFE95/99, PFE99, VFE99, N95/N99, FEP1/2/3, KF80/94/99, etc. MOQ 3,000 KGS per item Leading Time Within 15~30 days upon receipt of deposit and confirmation of samples Payment Terms T/T, L/C, D/P, etc. Characteristics Customized as the application and requirements, some characteristics as follow: 1. High strength, small difference at longitudinal and longitudinal direction; 2. Acid, non-toxic, non-tradiation, harmless to human physiology; 3. With excellent breathability; 4. Master batch dying, never fade; 5. Smooth, bright color, roll slitting, easy use, best quality.
Meltblown Nonwoven Meltblown nonwovens, the fineness fiber up to 1m, generally 1~3m. Meltblown nonwovens has special fiber structure and unique production process, it has a wide range of applications, such as filter materials, medical materials, sanitary suppliers, sound-absorbing materials, oil-absorbing materials, thermal materials, wiping cloth and other fields. Raw Material 100% Polypropylene Color White, Black Width 10-160cm Weight 9-300gsm Grade BFE95/99, PFE99, VFE99, N95/N99, FEP1/2/3, KF80/94/99, etc. MOQ 3,000 KGS per item Leading Time Within 15~30 days upon receipt of deposit and confirmation of samples Payment Terms T/T, L/C, D/P, etc. Characteristics Customized as the application and requirements, some characteristics as follow: 1. High strength, small difference at longitudinal and longitudinal direction; 2. Acid, non-toxic, non-tradiation, harmless to human physiology; 3. With excellent breathability; 4. Master batch dying, never fade; 5. Smooth, bright color, roll slitting, easy use, best quality.
Meltblown Nonwoven Meltblown nonwovens, the fineness fiber up to 1m, generally 1~3m. Meltblown nonwovens has special fiber structure and unique production process, it has a wide range of applications, such as filter materials, medical materials, sanitary suppliers, sound-absorbing materials, oil-absorbing materials, thermal materials, wiping cloth and other fields. Raw Material 100% Polypropylene Color White, Black Width 10-160cm Weight 9-300gsm Grade BFE95/99, PFE99, VFE99, N95/N99, FEP1/2/3, KF80/94/99, etc. MOQ 3,000 KGS per item Leading Time Within 15~30 days upon receipt of deposit and confirmation of samples Payment Terms T/T, L/C, D/P, etc. Characteristics Customized as the application and requirements, some characteristics as follow: 1. High strength, small difference at longitudinal and longitudinal direction; 2. Acid, non-toxic, non-tradiation, harmless to human physiology; 3. With excellent breathability; 4. Master batch dying, never fade; 5. Smooth, bright color, roll slitting, easy use, best quality.
Meltblown Nonwoven Meltblown nonwovens, the fineness fiber up to 1m, generally 1~3m. Meltblown nonwovens has special fiber structure and unique production process, it has a wide range of applications, such as filter materials, medical materials, sanitary suppliers, sound-absorbing materials, oil-absorbing materials, thermal materials, wiping cloth and other fields. Raw Material 100% Polypropylene Color White, Black Width 10-160cm Weight 9-300gsm Grade BFE95/99, PFE99, VFE99, N95/N99, FEP1/2/3, KF80/94/99, etc. MOQ 3,000 KGS per item Leading Time Within 15~30 days upon receipt of deposit and confirmation of samples Payment Terms T/T, L/C, D/P, etc. Characteristics Customized as the application and requirements, some characteristics as follow: 1. High strength, small difference at longitudinal and longitudinal direction; 2. Acid, non-toxic, non-tradiation, harmless to human physiology; 3. With excellent breathability; 4. Master batch dying, never fade; 5. Smooth, bright color, roll slitting, easy use, best quality.