TTC can produce fixed asphalt plants with a capacity of 80-320 t / h. TTC asphalt plants are able to meet the demands of our customers with their models in various capacities, quality and economic operating costs, after sales support. Advantages Easy Maintenance 24/7 after sales asphalt plant technical support Long-lasting wear parts Operator friendly automation system (multi language support) Easy disassembly and installation. Asphalt plant design suitable for different asphalt productions. Asphalt Plant Equipment Features Cold feeding bunkers store the materials of different sizes and transfer them to the system according to the product recipe. It is the feeding equipment of asphalt plant. Cold Feed Bunker Features TTC asphalt plants have functional design with cold feed bunkers, bolted parts. Easy to install. Thanks to the cold feeding bunkers, high strength silo body and twisted body, no deformation occurs under load. Product feeding can be done precisely thanks to frequency controlled dosing conveyors Dryer Features TTC fixed asphalt plants have steel forged rings for high strength and long life. In order to prevent heat losses, asphalt plant dryer is insulated with rock wool and a long-lasting insulation is provided by covering it with stainless steel sheet. TTC asphalt plant dryers work with soft starter to avoid problems under load. Dryer burners are supplied from world famous brands. Asphalt plant dryer (burner) can be supplied with double fuel if desired. Vibrating Screen Features Dust-proof design Easily replaceable screen wires and easy maintenance 4-5 or 6 fraction screen design Screen by pass system Mixer Features High quality gearboxes (synchronous) connected to each other, suitable for heavy duty operation Heat and abrasion resistant inner casing plates Long-life mixer arms and shoes Heaters placed on the mixer discharge cover to prevent freezing Dust Filter Features Filter, inlet and outlet temperature measurement Fresh air clapper to prevent the filter from being damaged by high temperature Heat resistant metaaramid upright bags Dustproof design The bags are easily interchangeable Reverse flow bag cleaning system Isolation system suitable for climate conditions and heat transfer Automation Asphalt Plant Automation Features Fully automatic and manual control options Software in the language suitable for the country where our customers are located Possibility to determine the desired number of recipes and report on how many products are given to which customer High quality materials and equipment Emergency stop system suitable for work safety
Product Code Product Description PRS-ZE000035 Hydraulic Sample Extruder PARSROS Hydarulic Sample Extruder is used for a smooth and rapid extrusion of soil samples from tubes also of thin walls with minimum disturbance. The unit extrudes samples from dia. 35 up to 101,6 mm with max. stroke of 900 mm. The hydraulic piston is equipped of speed adjuster and can be stopped in any excursionâ??s position. The extruded sample is held in place by a receiving table adjustable in height and easily lowered along side the machine to save space. Complete with adaptors (ring + tamper) to extrude samples having dia. 38, 83, 100 mm Max. load 30 kN Dimensions (working position): 2741 x 635 xh 1200 mm Power supply 220-240 V 1ph 50/60 Hz 1300 W Weight: 160 kg
Product Code Product Description PRS-CMTC03 Mortar Permeability Tester ( 3 Unit ) This method of test covers the procedure for determining the permeability to water of the pozzolana mortar prepared and cured under specified conditions, by measuring the percolation of water through Standard cylindrical specimens. The permeability unit shall consist of a specimen container ring of 100 mm diameter and 50 mm high, held between a bottom plate and a water cell. The hydraulic head for testing shall be obtained by connecting the unit to a compressor through a water pressure vessel. A pressure regulator and pressure gauge shall be included between the compressor and the water pressure vessel to indicate the test pressure. Water percolating through the specimen shall be collected in a container. Typical details of an individual unit are given in fig. 6 and 7. The water cell shall be 100 mm diameter brass cylinder and the top and bottom plates shall be either of brass or any other non-corroding metal. The connecting pipeline from the water cell to the water pressure vessel shall also be of non-corroding metal or of hard board polythene. This requirement is necessary since the tests last over a number of days in which mild steel or similar materials will get corroded and the rust formed will coat the top of the specimens and affect the permeability. The connection of units to the air cylinder shall be done with armoured heawy-duty rubber hose.
Product Code Product Description PRS-A0810 Accelerated Polishing Machine (PSV),220-240 V 50-60 Hz PRS-A0812 Corn Emery 5 kg, for PRS-A0810 PRS-A0813 Flour Emery 5 kg, for PRS-A0810 PRS-A0814 Control Stone 50 kg Ungraded, for PRS-A0810, PSV value in the range 50 to 60 PRS-A0815 Friction Tester Reference Stone (Criggion Stone) 25 kg Ungraded, for PRS-A0810, PSV value in the range 60 to 65 Accelerated Polishing Machine (PSV) is used to accelerate the polishing action of vehicle tyres on a road surface, the resultsare used to develop safer road surfaces. The machine consists of a road wheel rotating at 320 ± 5 r.p.m, driven by a fan cooled electric motor. Abrasive Corn Emery is fed to the point of contact of the wheel on the test surface for 3 hours, followed by feeding Emery Flour to polish the surface being tested for a further 3 hours. Subsequent skid tests are carried out on the test samples using suitable portable skid test equipment. PRS-A0814 Control Stone and PRS-A0815 Friction Tester Reference Stone should be ordered separately. The Accelerated Polishing Machine is supplied complete with; � Road Wheel, � Side Plate, � Rubber Rings, � Solid Rubber- Tired Wheel - 2 units, � Drive Belt, � Abrasive Feed Mechanism, � Corn Emery - 5 kg, � Flour Emery - 5 kg, � Tool Kit, � Specimen Moulds - 2 pcs, � 2 Mould Plates Road Wheel Speed 315 to 325 r.p.m Dimensions 740x720x1520 mm Weight (approx.) 175 kg Power 850 W
Process for the oxidation of bitumen, according to which a feed stream of bitumen and a stream of air or of another gaseous oxidizing agent are sent to a pressurized reactor, said reactor being a so-called rotary apparatus . The reaction between the gaseous oxidizing agent and the bitumen or other in the reactor is improved by generating turbulence by means of rotor-stator type mixing devices which produce shear forces making it possible to obtain a good dispersion of the oxidizing agent. The Oxidized Bitumen is defined as follows: bitumen whose rheological properties have been substantially modified by reaction with air at elevated temperatures. Preferably, the oxidized bitumen has a softening point (ball and ring temperature) comprised between 85 and 95 C. The oxidized bitumen having a penetration at 25 C. of 5 to 15 mm are preferentially used.
