Silicone rubber raw materials (HTV, LSR, RTV), chemical additives, color masterbatches, pigments, color paste, silicone oil, primer, silicone gel, grease.
River nut, cage nut.
Adhesives, paints, waterproof material, resins, vam, EVA, PVA powder.
We deliver high quality products and we provide professional service to our customers.
Item no.: NE-478 Capacity: 15ml
Description 1. Tough film and good adhesion on the concrete, able to penetrate into concrete. 2. Good resistance to water , brine and chemicals. Excellent mechanical strength and physical properties. 3. Good resistance to impact and abrasion. 4. Easy application , drying fast. Prepare to use 1. Mix base and hardener by the mixing ratio and Stir thoroughly, then setting at least 15 minutes. Thinner may be used to reduce viscosity. 2. Remove all foreign particles, oils, grease , rust and moistures from the surface before application. 3. Two packs product, must be used completely during the duration of its pot life. 4. Donâ??t apply when the temperature is < 10â??,>40â??, relative humidity is >90â?? or the surface temperature of substrate is not higher than the dew point for at least 3â??. 5. If the coating interval is exceeded , the surface of base coat must be roughened to insure adhesion. 6. Keep away from heat, sparks and flame. 7. Stored with good ventilation. 8. Keep adequate ventilation during application. 9. The actual coverage may vary, depending on application technique, job conditions and type of surface. Under brushing & rolling application the actual coverage is estimated at 70% of the Theoretical coverage and 60% for spraying. **The parts of data base above could be affect by application condition at job site, please reference guide specification or contact with relative technical personnel. Color : Clear Drying time : Tack-free : 2 hours Hardness : 8 hours Full cure : 7 days (grease)
Metal in dross, slag, powder, ash, residue, sludge, metal scrap, metal ingots, copper cathode, metal concentrates and ore, plastic raw material in resin, granules, powder, regrinds scrap, plastic raw material in film & roll (ldpe film, hdpe film & pp film), plastic polymer, petroleum (crude oil ,diesel, d2, d6, fuel oil, en590 10ppm, mazut 100, jp54, jet a1, lng, lpg & blco (bonny light crude oil), lco (light cycle oil), zeolite, fly ash, gold dust/dore bars, brazilan frozen chicken commodity (feet/paws/wings).
Marine gauge
DOTP, PVC plasticizer, 2-ehs, 2-ethyl hexyl stearate, , ester for lubricant, polyethylene glycol ester , emulsifier and dispersant for textile CDE-G , ester for detergent, span-2080, emulsifier for water cutting oil and textile oil.
Pressure gauge, oxygen gauge, liquid filled/vacuum gauge, compound gauge - hourmeter, water temperature gauge, oil pressure, voltmeter, electrical pressure gauge, automobile gauge, tire pressure gauge, digital tire pressure gauge.
Features * With excellent adhesion, non-sagging and construction resistance. * Without cracking and bulging after curing. * Specific design for spray plastering. * Applying by spraying machines efficiently. * Suitable for tiling. * Interior wall, exterior wall, panel wall and small area ceiling rendering. Application 1. Substrate must be free from grease, mould oil, rust, rusty metal , wood peels, paints, plastics, loose particles, contamination on any traces of foreign materials affecting the adhesion of CS-010. 2. Moisten the substrate overnight and also at the time before the commencement of operation. 3. Suggest to use CC-400 Concrete Bond as primer to adding adhesion for smooth and low porous substrates. 4. CS-010 is suitable for any type of spraying machine. Mix a packet of 40KG powder with 6.4liter of water and stir well for use. Its thickness should be maintained at 15mm and wait for 6-24 hours to apply for increasing the thickness. Storage Storage life is 12 months if the product is kept in a dry place. Package 40kg/powder bag
DESCRIPTION ITLS PMS 60 is a single component elastomeric sealant without isocyanates. It cures rapidly under the effect of atmospheric humidity to form a flexible and resistant joint with very good adhesion on most materials. APPLICATION ITLS PMS 60 is suitable for industrial and refrigerated trailers, truck bodies, shipbuilding, air conditioning and ventilation units, sandwich panels and other industrial applications. ITLS PMS 60 can also be used for bonding and caulking different materials used in the building industry : concrete, wood, aluminum, most lacquered metals, polyester, glass, stone, ceramic, and so on. However, for difficult materials especially lacquered or non-ferrous metals, it is necessary to make tests beforehand. INSTRUCTIONS FOR USE SUBSTRATE PREPARATION: The substrates must be clean, even, dry, free of dust, oil, grease and any contaminants that could harm bonding. All traces of poorly adherent paints or coatings should be systematically removed beforehand. They may be cleaned with PMS primer, methylethylketone (MEK) or acetone. Check the compatibility of the solvent used with the substrates. It may be necessary to rub down the substrate beforehand. After rubbing down, the surface should be recleaned. Allow the substrate to dry after degreasing. When using solvents, extinguish all sources of ignition and carefully follow the safety and handling instructions given by the manufacturer. CAULKING: ITLS PMS 60 can be applied by a manual or pneumatic gun. After application, use a putty knife to smooth the joint with soapy water. Do not apply at a temperature under 5 C. In cold weather, store the cartridges at about 20 �°C before use. This product should be used within 24 hours of opening the cartridge protection; otherwise, the sealant could harden inside. Avoid any contact with non-cured polyurethanes during curing. CLEANING: Tools can be cleaned with PMS primer, MEK or acetone before the sealant has completely cured. After curing, abrasion is necessary. STORAGE AND SHELF LIFE 12 months in the original, hermetically sealed packagings between 5 and 25 C PACKAGING 290 mL cartridges and 600 ml sausages SAFETY Not classified as hazardous. Read the material safety data sheet before use.
DESCRIPTION CC-610S Modified Polyurethane weather-shield is a two component with great bonding strength on materials that are hard to adhere. CHARATERISTIC More suitable coating on surface as soft plastic, PVC, ABS, PCâ?¦..etc. Non-yellowish and excellent gloss and color retention after exposure in outdoor. Resist from most chemical products Coating oil or color changing for tiles, imitation rocks. Glass-painting and painting for iron, zinc plate, and stainless steel High weather resistance and high gloss corrosion prevention paint for cement, stones, asbestos, bricks, wooden materials, and bamboo wood. NOTES Please mix and stir well before using Please make sure the lid is closed tightly. Please keep the surface free of dust, loose or paint before painting The tools are washable by solvents after application. Avoid direct sunlight or high temperature environment to ensure excellent product quality. Keep the storage environment well ventilated and stay away from flammable when applying paints. The actual volume application depends on the surface condition.
DESCRIPTION a premium cement based finish skimcoat which contains selected filler, additive and polymer used for smooth finishing to uneven concrete wall & ceiling. After dry STARCOAT CN have a excellent adhesion to the substrate, better impact resistant, no powdery, no cracks, smooth and ready to be painted with water based wall paint. Easy to use, good workability and have a long pot life and correction time even at the outdoor applications. USES IN APPLICATIONS 1. Cement Based Wall Plaster. 2. Concrete Wall, Column & Ceiling 3. Precast Concrete & Concrete profile 4. Internal & External. ADVANTAGE * Light, good workability and sanding properties. * No cracks and hair cracks. (depends on background) * Smooth surface, solid and no powdery. * Can be painted or finished with wallpaper directly after dry in minimum 24 hours * without using PVA putty to leveling up & filling uneven rough surface. PRODUCT SPESIFICATIONS 1. Main Binder : Portland Cement & Polymer 2. Filler : Limestone 3. Color : GREY and WHITE. 4. Mixing Ratio : 7 - 8 litres of water per 25 Kg bags. or 28 - 32 % water demands. 5. Coverage : 1.25-1.3 Kg/m2/mm or 19m2/25 Kg/mm thickness average 7.5m2/25Kg for 2-3mm thickness 6. Thickness : 2mm thickness/coat 4mm for 2 coats and 6mm for 3 coats. 7. Pot Life : approx. 60 minutes SURFACE PREPARATION * The substrate must be clean and free from grease and loose particles. Recesses should be pre-patched and levelled where appropriate. * Porous and absorbent substrates must be pre-wetted prior to application of Starcoat CN finish coat.
DESCRIPTION STARCOAT PL, is fine grade cement based finish plastering skimcoat which contains selected filler and additive used for smooth finishing to uneven wall cement based plaster and ceiling. After dry STARCOAT PL have a good adhesion to the substrate, no cracks, smooth, no dust on the surface and ready to be painted with water based paint. Easy to use, good workability and have a long pot life and correction time even at the outdoor applications. USES IN APPLICATIONS *Cement Based Wall Plaster. *Precast Concrete. *Concrete Profile & Concrete Ceilings *Internal & External. ADVANTAGE *Light, good workability and sanding properties. *No cracks and hair cracks. (depends on background) *Smooth surface, solid and no powdery. *Can be painted or finished with wallpaper directly after dry in minimum 24 hours without using PVA putty to leveling up & filling uneven rough surface. PRODUCT SPESIFICATIONS 1. Main Binder : Portland Cement & Polymer 2. Filler: Limestone 3. Color: GREY and WHITE. 4. Mixing Ratio : 7 - 8 litres of water per 25 Kg bags. or 28 - 32 % water demands. 5. Coverage: 1.25-1.3 Kg/m2/mm or 19m2/25 Kg/mm thickness average 7.5m2/25Kg for 2-3mm thickness 6. Thickness: 2mm thickness/coat 4mm for 2 coats and 6mm for 3 coats. 7. Pot Life: approx. 60 minutes SURFACE PREPARATION 1. The substrate must be clean and free from grease and loose particles. Recesses should be pre-patched and levelled where appropriate. 2. Porous and absorbent substrates must be pre-wetted prior to application of Starcoat PL finish coat.
Description CS-613FD is a water-based multi-purposed epoxy putty and adhesive. It is developed for filling seam, gap between Calcium Silicate board. It is environmentally friendly which does not pose health hazard to user and dwellers. The best part is how easy it can be cleaned with just water. It is easy to mix even by hand due to our innovative water-based technology. Features Paintable easily with wb coating Easy to use Smooth to tool with trowel Non-sagging Stronger adhesion High solid by volume; 100% water resistant when cured. Low odor VOC free / Solvent free Uses Gypsum boardCalcium silicate board Fiber cement board Plywood / Timber Concrete / Tile It may be suitable to use on other substrates not mentioned above. Application 1. The surface to be adhered must be free of dust, release agent, oil and grease 2. Mix part A and part B with 1: 1 (by volume), and stir until homogeneous as indicated by uniform color. 3. Do not stir or mix the two parts on the application surface.
PREPARATIONS The substrate, bolt and anchor holes must be clean, sound, dry and free of oil, grease, without laitance and loose particles. Prewet the bolt holes thoroughly, but no standing water in it. Before applying ITLS CA-007H absorbent substrates must be saturated thoroughly, but without standing water. MIXING Mix 3.2-4.4 liters of clean water with 25kg bag of ITLS CA-007H together. To add water based on the condition of stirring and keep stirring around 5 minutes until grouting well. APPLICATIONS Pour ITLS CA-007H mortar after mixing into the reserved cavities and recesses use the stick or bar to remove the air bubble, ensure that air entrapped into the grout is allowed to escape. Suggest to blend the grout by auto-mixer for better application. COVERAGE 25 Kg ITLS CA-007H when mixed with water will produce approx. 13.5 liters of Liquid Grouting Mortar. ITLS CA-007H suggest to be placed in thickness ranging from 10-15cm/layer.
DESCRIPTION ITSEAL is truly developed for sealing window frames with highly durable and flexible properties to withstand severe weathering and extreme temperatures. It seals small gap that normal sealant cannot reach and penetrate. It provides a truly watertight seal deep into minute joint and gap. FEATURES * ITSEAL is the only waterproof sealer that is completely watertight. * It is highly water repellent that no water can get through it during storm. * It adheres well on aluminum and glass * Once dried, ITSEAL is flexible and accommodate joint movement due to vibration. * Mill finish aluminum, oil or wet surfaces can also be well-sealed. VOC CONTENT Type of Regulated Adhesive under the Air Pollution Control (Volatile Organic Compounds) Regulation of Hong Kong: Architectural Sealant VOC Content (Ready to use): 248g/Ltr. SURFACE PREPARATION For maximum adhesion, the adhesive surface must be free of dust, release agent, oil and grease. Wipe surface with solvent is recommended. Solvent are obtainable from ITLS-SB. This information in this catalogue is provided to the best of our knowledge from results gathered both internal and external credited laboratories. However, we have no control over site applications, site conditions and workmanship of the applicator. We therefore will not accept any liability, either directly or indirectly arising from the misuse of these products or when the product is used not in accordance with any advice, specification, and recommendation of information given by us, The user is responsible for checking the suitability of these products for its intended use. APPLICATION ITSEAL can be used with hand operated or air operated grease pump. Other simple extruding device can also be used but it has to be solvent resistance. LIMITATION * Not suitable large gap wider than 5 mm wide and deep. For deeper joint fill to half of it, let it dry overnight and fill it up the next day. * Not suitable for use as expansion joint. COLOUR AND PACKING 26 kg / pail Grey/Black/Bronze/White SAFETY INFORMATION * ITSEAL is flammable. Please keep away from sources of ignition during application. * Avoid breathing in solvent by wearing solvent vapor respiratory mask in badly ventilated area or confined space. * Avoid contact with skin and eyes. If swallowed please contact doctor immediately. * ITSEAL meets the requirement of RoHS regulation of European Union and it does not contain eight heavy metals which were restricted by ASTM F963 or EN71 part3. * Please read the Material Safety Data Sheet in regards to flammability and health and hazard. SHIPPING/STORAGE INFORMATION ITSEAL must be stored in a cool place under 25°C and away from direct sunlight. The shelve life is 12 months if stored in accordance to the recommendation. Dangerous Goods Information: Cement Adhesive, Class 3, UN1133 PG III.
DESCRIPTION CC-610 Modified Polyurethane weather shield is a two component with great bonding strength on materials that are hard to adhere. CHARATERISTIC Dust proofing and possessing self cleaning capability Excellent water and weather resistance Firm coatings with good alkaline resistance Fast setting rate and easy to apply APPLICATION Coating oil or color changing for tiles, imitation rocks. Glass painting and painting for iron, zinc plate, and stainless steel High weather resistance and high gloss corrosion prevention paint for cement, stones, asbestos, bricks, wooden materials, and bamboo wood. Color : Clear & standard colors Viscosity : 75-110 KU Solid content : 30%-55% Coating time interval : 2 hours minimum Weight mixed ratio : Clear/1 0 : 1 Colored/1 1 : 1 Packaging Clear 14kg : 1.4kg (5 gallon per set) Colored 20kg : 1.8kg (5 gallon per set) Apply methods Brush, spray, roller coating
DESCRIPTION CP-310 was synthesized from imported high-technology macromolecule resin and specialized paint that is different from general acrylic resin. CP-310 is a perfect product to provide a high water-tolerant, climate-tolerant, and anti-UV ability. FEATURES * Excellent environmental water-based waterproofing paint * Water-based, Non-toxic, odorless, inflammable, and harmless * Fine adhesion, extreme toughness, high elastic, and high endurance * Hydrophilic, and may be applied on damp surface USE RoofBuilding, condominium, factory, barracks, school, garden and etc.. WallsBasement wall , exterior wall , and etcâ?¦ PREPARATION 1. (The following steps are recommended for best results) 2. New concrete must cure for a minimum of 30 days 3. All holes or cracks must be properly patched 4. All surfaces must be clean and free of dirt, dust, efflorescence and oil APPLICATION (The following steps are recommended for best results) 1. Stir well before use. Do not thin; however, if thinning is necessary, thin water at a rate of no more than 10% 2. One prime required CP-310 primer 3. Two coats are required for the best resultskeep the thickness of each coating below 1m. 4. Wait for each coating to be total dry before overlaying the next coat. The interval time between each coating is minimum of 8 hours. COVERAGE 5-gallons about 33m2 COLOR Grayã??Whiteã??ivoryã??Green DRY TIME Dries to touch in about 1-2days . Low temperatures or high humidity conditions will affect drying time. Full cure should be reached in 14-30 days. CLEAN UP 1. Clean hands and tools with soap water. 2. After 30 days or paint has fully cured, areas may be wasted using a non-abrasive, mild detergent and cellulose sponge. WARNING (Read the following carefully for your own safety) 1. Keep out of reach of children-Do not take internally. 2. May cause eye, skin and respiratory tract irritation. May be harmful if swallowed. Use only with adequate ventilation.