Each group is divided into two components at the proportion of 30:4.5, weighing 34.5kg. It is used as first run of protective primer of heavy duty anticorrosion coating, featuring good anticorrosion performance, thinning after adding water, environmental friendly, no harm.
Description Two component metallic zinc rich epoxy high performance primer. Recommended Use :- The zinc pigment in dry film renders excellent protection to steel structure, tanks, bullets, dam gates, pipelines, plant equipments, jetty, etc. in both interior and exterior exposed conditions of fertilizer units, chemical plants, steel plants, cement plants, pulp and paper industries, ports, power plants, petrochemical and pharmaceutical industry, transformer, machines & other heavy duty OEMs. It also provides cathodic protection to steel and gives good resistance to corrosion at local damaged areas. It is useful in heavy-duty protective paint systems. It is recommended not to expose the primed coat alone to chemical and saline atmosphere for a long time. Physical Data COLOUR : Grey FINISH : Matt SOLIDS BY VOLUME : 50 �± 3% THEORETICAL SPREADING RATE : 10 sq.mt / ltr at DFT of 50 �µ FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C DRYING CHARACTERISTICS (at 30�°C & at 65% Relative Humidity) : HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to minimum Sa 2 1/2 Standards is recommended with a profile of 35 - 75 microns. The surface should be absolutely dry and salt free before application. The primer should be applied preferably immediately or within 4 hours of blasting. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 POT LIFE : 4 hours min at 30�°C RECOMMENDED DFT : 30 50 µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : Infinite COMPATIBILITY : Compatible with Epoxy, PU, Chlorinated Rubber intermediate/finish coat.
Refractory bricks, high alumina bricks, acid proof bricks, tiles and castables, all mortars and fire clay, low cement castables, insulating castables, conventional dense refractory bricks, insulation bricks, cold face, hot face insulation bricks, hot face insulation bricks, acid resistant bricks/components, membranes, acid resistant cement, construction chemicals, class 1 ar tiles and bricks 38mm and 75mm, 4457 vitrified ar tiles with 0% water absorption, 20mm & 25m, primer, mastics, pot. silicate cement, coerce cement, furnace based cement, crushed refractory boiler bed material, acid resistant tiles, acid resistant brick fireclay type, acid resistant brick red shale type, bitumen primer, epoxy resin & hardner, furan powder and syrup solution,.
Brighto Epoxy Zinc Chromate Primer Price : 3.60 Ltr -USD 29.7 18 Ltr- USD 112.4
Zinc Sulphate Mono/Hepta(IP/USP) high quality and High Standard Zinc Sulphate Supplier of Zinc Sulphate Heptahydrate-21% , Zinc Sulphate Monohydrate -33% , Zinc Sulphate Monohydrate -35% Zinc Sulphate Monohydrate 26% 33% Zinc Sulphate Powder, the rich source of zinc is essential for healthy growth and reproduction in plants.
We source high quality Ores and Others that are majorly used in numerous of Industries for diverse uses. The wide collection of Mineral Ores is free from impurities and rich in other essential features. Our esteemed client’s can avail the wide gamut of Mineral Ores at very pocket friendly price. We deal in * Bauxite ore * Copper ore * Lead ore * Nickel ore * NPI -Nickel pig iron * Tin ore * Zinc ore etc
Nutmeg and mace spice contains many plant-derived chemical compounds that are known to have been anti-oxidant, disease preventing, and health promoting properties. The spicy nut contains fixed oil trimyristin and many essential volatile oils such as which gives a sweet aromatic flavor to nutmeg such as myristicin, elemicin, eugenol and safrole. The other volatile-oils are pinene, camphene, dipentene, cineole, linalool, sabinene, safrole, terpeniol. The active principles in nutmeg have many therapeutic applications in many traditional medicines as anti-fungal, anti-depressant, aphrodisiac, digestive, and carminative functions. This spice is a good source of minerals like copper, potassium, calcium, manganese, iron, zinc and magnesium. Potassium is an important component of cell and body fluids that helps control heart rate and blood pressure. Manganese and copper are used by the body as co-factors for the antioxidant enzyme, superoxide dismutase. Iron is essential for red blood cell production and as a co-factor for cytochrome oxidases enzymes. It is also rich in many vital B-complex vitamins, including vitamin C, folic acid, riboflavin, niacin, vitamin A and many flavonoid anti-oxidants like beta-carotene and cryptoxanthin that are essential for optimum health.
Castor meal is also variously called castor meal, castor residue, castor extract & de-oiled castor cake Castor meal - the residue obtained from castor cake by the solvent extraction process - is one of the most versatile natural manures. It is truly organic manure which enhances the fertility of the soil without causing any damage or decay. It is enriched with the three big elements vital and conducive to the proper growth of crops - Nitrogen, Phosphorus and Potassium. It also has traces of nutrients like Manganese, Zinc and Copper, thus making it a balanced fertilizer. Moreover, it helps to neutralize the detrimental effects of chemical fertilizers. Apart from their contribution to Nutrients, they have a number of benefits in agriculture, which none of the synthetic fertilizers or pesticides can offer. They bring in the wonderful molecules that nature has designed to help the plants flourish naturally. They provide slow and steady nourishment, stimulation, protection from soil nematodes and insects; improve yields, and quality of product like taste, flavour, amino acid composition etc. The pressed cake obtained after the expression of castor bean. The solvent extracted cake, although rich in protein cannot be used as cattle fodder because of its toxicity. However, it can be used as a fertilizer. The protein content of castor seed meal varies from 21-48% depending upon the extent of decortications. It has an ideal amino acid profile with moderately high Cystine, mithionine, and isoleucine. But its ant nutritional substances, ricin, ricine and an allergen restrict its use in poultry feed, even at a very low level of inclusion. Castor Cake is an excellent fertilizer because of high content of N (6.4%), Phosphoric Acid (2.55%) and Potash (1%) and moisture retention. There is negative correlation between the contents of ricinine in castor seeds and oil content (r = -0.76). This content of ricinine in castor seed is determined by Agro climatic conditions. Nutrient content of Castor Cake: Organic matter - 75 - 80 %, Nitrogen - 4.0 - 4.5 %, Phosphorous - 1.5 %, Potassium - 1.25 - 1.5 %. It also contains some micro nutrients viz., Calcium, Magnesium, Sulphur, Iron, Zinc, Manganese, Copper etc. A typical composition of castor residue/meal is as follows: Nitrogen - 4% min. approx. Phosphorous - 1% min. approx. Potassium - 1% min. approx. Moisture - 10 - 12 % max. approx. Oil Content - 0.7% max. approx. Advantages: 1. It provides all the major & minor nutrients necessary for better plant growth. 2. It also helps in increasing the nutrient uptake by plants. 3. It improves the soil fertility and productivity. 4. It is known to protect the plants from nematodes and termites. 5. It improves the yield & quality of the farm produce. 6. It improves the physical, chemical and biological properties of soil
Chinese Cabbage : Chinese cabbage is rich in nutrients, in addition to sugar, fat, protein, crude fiber, calcium, phosphorus, iron, carotene, vitamin B1, vitamin B2, is still rich in vitamins, vitamin C, vitamin B2 content than apple, pear Respectively, 5 times higher, 4 times; trace elements zinc higher than meat, and can inhibit the absorption of nitrite amine molybdenum Which vitamin C, can increase the body's resistance to infection, for scurvy, gum bleeding, a variety of acute and chronic infectious diseases prevention and treatment. Cabbage contains cellulose, can enhance gastrointestinal motility, reduce the retention time of feces in the body to help digestion and excretion, thereby reducing the burden of liver and kidney to prevent the occurrence of a variety of stomach problems.
Chestnut : Chestnut produces higher energy, is a nut type, contains the starch is very high. According to the investigation of dry chestnut carbohydrates reached 77%, fresh chestnuts have 40%, is the potato 2.4 times; chestnut which is 4% to 5% protein content, although not as peanut, walnut, but also than cooked The rice is taller. Fresh chestnuts contain vitamin C than the recognized vitamin C rich tomatoes to more, it is more than ten times the apple! Chestnut contains a wide range of minerals, potassium, magnesium, iron, zinc, manganese and other content than apples, pears and other common fruit is much higher, especially potassium-containing, than the so-called potassium-rich apple is also 4 times higher The chestnut not only contains a lot of starch, but also rich in protein, fat, B vitamins and other nutrients, heat is also high, chestnut vitamin B1.B2 rich in content, vitamin B2 content of at least 4 times the rice 100 grams also contains 24 mg of vitamin C, which is food can not match. Every 100 grams of protein containing 5.7 grams, 2 grams of fat, carbohydrates 40 to 45 grams, 25 grams of starch. Health chestnut vitamin content can be as high as 40 to 60 mg, cooked chestnut vitamin content of about 25 mg. Chestnut also contains calcium, phosphorus, iron, potassium and other inorganic salts and carotene, B vitamins and other ingredients.
Kiwi : The world's largest consumption of the first 26 kinds of fruit, kiwi is the most comprehensive. The content of Vc, Mg and trace elements in kiwifruit fruit was the highest. Among the top three low-sodium and high-potassium fruits, kiwi is at the top of the list because it contains more potassium than bananas and citrus. At the same time, the content of Ve and Vk in kiwifruit was determined to be excellent, low in fat and no cholesterol. According to the analysis, kiwi fruit vitamin content per 100 grams of fresh samples in general 100-200 mg, high up to 400 mg, about 5-10 times the citrus; sugar 8-14%, acid 1.4-2- 0%, but also with tyrosine and other amino acids 12 species. kiwi fruit contains a wide range of nutrients, most of the fruit is rich in one or two nutrients, but each kiwi can provide 8% DV folic acid, 8% DV copper, 8% pantothenic acid, 6% Fresh, 4% DV iron and vitamin B6, 2% DV phosphorus and Va as well as other vitamins and minerals. Kiwi in addition to kiwi alkali, proteolytic enzymes, tannin pectin and sugar and other organic matter, as well as calcium, potassium, selenium, zinc, germanium and other trace elements and the human body needs 17 kinds of amino acids, but also rich in vitamins, , Fructose, citric acid, malic acid, fat. A kiwi can provide a day more than twice the demand for vitamin C, known as the "king of fruit." Kiwi also contains good soluble dietary fiber, as the fruit of the most eye-catching place is contained in its superior antioxidant properties of plant chemical substances sod, according to the US Department of Agriculture research report, kiwi comprehensive antioxidant index in the Fruits among the top, second only to the thorns, blueberries and other small fruit, far stronger than apples, pears, watermelon, citrus and other daily fruits. And blueberries belong to the second generation of fruit is quite representative. Compared with sweet orange and lemon, kiwi fruit contains vitamin C ingredients are two times the first two fruits, so often used to fight against scurvy. Not only that, kiwi can stabilize mood, lower cholesterol, help digestion, prevent constipation, as well as thirst and diuretic and protect the role of the heart.
Epoxy Zinc Rich Primer
Description Two component Epoxy based anti corrosive primer containing zinc phosphate as corrosion inhibiting pigments Recommended Use :- It is recommended as primer on M.S surface for OEM's as well as for process industries like fertilizers, refineries, chemicals and other plants. It can also be applied in diverse areas of tank exteriors, equipments, pipelines, structural steel, etc. Not to be used for immersion application. Physical Data :- COLOUR :- Yellow FINISH :- Matt SOLIDS BY VOLUME :- 40 �± 3% THEORETICAL SPREADING RATE :- 13.33 sq.mt. / ltr. at recommended DFT of 30 �µ FLASH POINT :- Base : 23�°C Hardener : 23�°C DRYING CHARACTERISTICS :- SURFACE DRY : 60 to 90 minutes (At 30�°C & 65% Relative Humidity) :- HARD DRY : Overnight. FULL CURE : 7 Days SHELF LIFE :- BASE : 6 months HARDENER : 6 months SURFACE PREPARATION Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application Application Data MIXING RATIO :- Base : Hardener (As per our recommendation) APPLICATION :- By Brush / By Conventional Spray / By Airless Spray THINNER :- Epoxy Thinner 190 POT LIFE :- 4 hours min at 30�°C RECOMMENDED DFT :- 30 - 40 �µ. OVERCOATING INTERVAL :- MIN : 8 Hours MAX : 24 Hours COMPATIBILITY :- Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly cleaned. Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. . Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application. For Conventional Spray application:- Thinner : Epoxy Thinner 190 Addition : 10-15% Nozzle Orifice : 1.2 1.4 mm Nozzle Pressure : 40 - 70 p.s.i. For Airless Spray Application:- Thinner : Epoxy Thinner 190 Addition : Max 5% Nozzle Orifice : 0.37- 0.42mm Nozzle Pressure : 1400-1800 p.s.i.
Epoxy Primer -guard Primer Is 2 Component Paint System For Interior Walls
Product formation�? Be composed of epoxy resin, additive and organic solvent, then adding superfine zinc powder Product features: . Anti rust property because it including zinc . Good mechanical, good adhesion . Wear resistance, water resistance, solvent resistance, heat resistance, . The zinc spray is small while electric welding, the area of the burn is small, and no effect on welding. . Used for workshop primer Using Anti rust primer for metallurgy, containers, ships, bridges, towers, oil pipeline, vehicle manufacturing, steel shot pre assembly, steel structure equipment surface treatment used for anti-corrosion coating on the surface of galvanized Packing Paint:25 kg/bucket Curing agent: 3 kg/bucket z
Description Two component Epoxy based anti corrosive primer pigmented with Zinc Chromate as corrosion inhibiting pigments. Recommended Use :- It is recommended as primer on M.S surface for original equipment manufacturing as well as for process industry as in various fertilizer, refineries, petrochemical, chemical and other plants, applied in diverse areas of tank exteriors, equipments, pipelines, structural steel, etc. Not to be used for immersion application. Physical Data COLOUR : Assorted FINISH : Matt SOLIDS BY VOLUME : 40 ± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt. / ltr. at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C DRYING CHARACTERISTICS : SURFACE DRY : 60 90 minutes (At 65% Relative Humidity & at 30�°C) : HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray THINNER : Epoxy thinner 190 POT LIFE : 4 hours min at 30 C RECOMMENDED DFT : 30 - 40 au. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth of 100 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned. Application :- By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in criss-cross manner and ensure the uniform application. Use quality brushes for paint application For Conventional Spray application :- Thinner : Epoxy Thinner 190 Addition : 10-15% Nozzle Orifice : 1.2 -1.4 mm Nozzle Pressure : 40-70 psi For Airless Spray application :- Thinner : Epoxy Thinner 190 Addition : 10-15% Addition : Max 5% if required Nozzle Orifice : 0.37- 0.42mm Nozzle Pressure : 1400-1800 psi
Description Two component Epoxy based anti corrosive primer containing red oxide and zinc chromate as corrosion inhibiting pigments Recommended Use :- Recommended as a primer on suitably cleaned mild steel surface in various fertilizer units, refineries, chemical and other plants, transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. The product is recommended as a primer for mild to moderate service conditions. Not to be recommended for immersed water condition Physical Data COLOUR : Red FINISH : Matt SOLIDS BY VOLUME : 40 + 3% THEORETICAL SPREADING RATE : 13.33 sq.mt / lt at recommended DFT of 30 FLASH POINT : Base : Above 23C Hardener : Above 23C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30C) : SURFACE DRY : 60 - 90 minutes HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application Application Data :- MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 POT LIFE at 30�°C : 4 hours min at 30�°C RECOMMENDED DFT : 30 40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated Rubber and Synthetic Enamel finish paints. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application. For Conventional Spray application :- Thinner : Epoxy Thinner 190 Addition : 10-15% Nozzle Orifice : 1.2 -1.4 mm Nozzle Pressure : 40-70 p.s.i. For Airless Spray application :- Thinner : Epoxy Thinner 190 Addition : Max 5% if required Nozzle Orifice: 0.37- 0.42mm Nozzle Pressure : 1400-1800 p.s.i.
Textile Epoxy Primer
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Magnesia Bricks Description Magnesia Bricks are alkaline refractory materials. These products have over 90% magnesium oxide content and adopt periclase as the principal crystalline phase. Magnesia Bricks can be divided into two categories of Burnt Magnesia Bricks and Chemical Bonded Magnesite Brick. They have excellent performance of superior high temperature mechanical strength and volume stability. Magnesia Bricks can service in the high temperature of 1750.. They are ideal products for glass furnace application. Magnesia Bricks Features: It is a kind of alkaline refractory product with periclase as main phase magnesite-alumina spinel clinker as basic material. the product has such characteristics as good temperature vibration, good strength and volume stability in high temperature. Magnesia Bricks Application Basic open-hearth furnace for steelmaking Electric furnace bottom and wall Permanent lining of oxygen converter Non-ferrous metal metallurgy furnace Hyperthermia tunnel kiln Lining of rotary cement kiln Heating furnace bottom and wall Regenerative chamber of glass furnace Magnesia Bricks Properties High Refractoriness Good alkaline slag erosion resistance High apparent initial softening temperature Good thermal conductivity High thermal expansion Magnesia Bricks Manufacturing Process Burnt Magnesia Bricks are manufactured with magnesite clinker as the raw material and fired in the high temperature of 1550~1600 after smashing, burdening, mulling and molding. High-purity products can be fired in the temperature that over 1750. Chemical bonded magnesite brick is produced with certain chemical bonding through mixing, molding and drying.