Features: 1. 20-250VAC/VDC universal power supply 2. Solid-state or relay output 3. Compact or standard units 4. No calibration required 5. Explosion proof units available 6. Mini, standard and extended probe versions
r with good fluidity in various fields. Other information Installation method: Vertical or horizontal installation
Explosion proof typed tuning fork level switch, d ii ct6 Fundamental principles The su-yc vibrating probe level switch/liquid level control switch is a kind of universal liquid level switch, which is brought to its resonance frequency by means of piezoelectric crystals drive. If the tuning fork is covered by liquid or solidity, this frequency will change. The electronics of the su-yc monitor the resonance frequency and then output a switching value, in this way, to alarm and control the liquid level. The structure and characteristics of tuning fork liquid level switch make it can replace any level switch of other principles, and can be widely used in building materials, petroleum, chemical industry, light industry, metallurgy field to alarm or control the height of liquid level for their lower and upper limit. Qualification Power supply: ac 110v/ac 220v 50hz / dc 24v Operating temperature: fork: -30-150¡ãc Instrument:-30-70¡ãc Operating pressure: ¡ü2mpa Fluid density: 0.6g/cm3 (in minimum) Action point: vertically insert into water about 25mm Start up time: about 3 sec Response time: about 1 sec Output style: one or two sets of relay contact (ac 220v/3a, dc 30v/ 3a) Output delay time: 1-20sec, can be adjusted Sensitivity: 10 grades can be set Consumption: ¡ü1w Process connection: r 1 taper pipe thread or others. Explosion proof: exd ii ct6 Exia ii bt4 Standard export packing.
Leader tuning fork level limit switch ld-yc-yg Free from service Against high pressure and corrosion Suitable for both solid and liquid media No mechanical parts, free from service
High frequency radar level meter, guided wave level meter, float level guage, flowmeter, magnetostrictive flap level meter, tuning fork level switch.
Each item is carefully polished to a naturally smooth finish in our organic bamboo cutlery set, which includes a knife, fork, and spoon. They won't scratch dishes or leave a mark, unlike other unconventional cutlery. This set of reusable spoons, knives, and fork is ideal for everyday usage, picnics, and other outdoor activities. These bamboo tools are light and robust and will withstand a lot of usage and damage.
WC pan for high level cistern.
General Purpose Fresh Coir Block (Processed & Compressed Coir) Coir pith blocks ensure high oxygen levels and therefore good drainage properties. They reduce the dormancy period of seeds and promote early sporting in almost all flowering plants and vegetable crops, We can supply coir blocks as Fresh Coir Blocks for vegetables/fruits and High Drain Rose Mix Coir Blocks specially designed to be used with Roses. Can be supplied in different weights, sizes or as per buyer’s requirements. Please contact us for more details and price quotations Advantages of Fresh Coir Blocks: Designed for vegetable and fruit plants Faster binding of soil Resistant to mold & rot; no chemical treatments needed Great air and water permeability Holds the seeds/saplings in place Excellent medium for quick vegetation No removal costs; Naturally degrades over a period of 2 to 5 years time Promotes deep rooting of plants Provides nutrients Easy to install Eco-friendly We can make 5 kg and 15 kg blocks.
For the Mosquito killer Led Bulb Light, is a 900 lumen bulb that doubles as an insect killer. The light features a blue UV LED which attracts insects into a Mosquito Killer grid.And the Mosquito Killer grid uses only 1W of electricity, while the light itself uses a meager 9W – and both can be used independently.They are used at home and outdoor. A brush is provided to clean off insects once the bulb switched-off.Compare to other traditional mosquito killer, this bulb has no chemicals, no sprays and hence no fumes to our life. • 2nd generation 2-in-1 LED LIGHT Bulb Plus LED Mosquito Killer Bulb • Wattage: 10W • Blue UV light • Lumen: 900-1000lm • Color Temperature (CCT): 6500K • Input Voltage: AC 90-130V & 220v-240V • With CE and ROHS Operation: Step1: Switch it on,both lighting +killing are on. Step2: Switch on again,light off,only killing on. Step3: Switch on again,killing off,only light on. Step4: Switch off, both off.
Technical data: Oxygen flow:0.5-5L/min Oxygen concentration:95.5%-87% Output pressure: 40-70kPa Pressure relief mechanism operational at: 250kPa + 25kPa Operation nose Level
Oxygen Concentrator - 0.5-10L/Min Purityï¼? 96% Compressor Life - 25000hours Sound Level 60dB Screen - LED Segment real-time display Power comsumption - 500VA Net Weight - 23k Gross weight:27kg
Two tier Galvanized double deck bike rack/bicycle rack For all types of bicycles 2 tier bike rack can accommodate all types of bicycles, such as mountain bikes and town bikes, and any bicycles can also be chained for extra security. Once placed, the bicycle is well supported by wheel channels and the back wheel is stabilised by a gutter to lock the bicycle firmly. The lower rack has a sloping wheel channel, so the user does not have to bend between the levels which makes the cycle parking system simple and easy to use for all ages. This 2 tier bicycle rack is excellent for space saving as the cycle stands are compact with a centre to centre distance of around 370 mm. There is also the option to have the powder coated in any of the 192 RAL colours. Double deck bicycle rack features: 1.This double deck bicycle rack can park 2 bikes per set(one up, one down). 2.assembled in underground garage. 3.used for public place such as hosipital, school etc. 4.beautify the environment. 5.can Save space and prevention of theft.
1.Product overview The 80X series sensor is a 26G high frequency radar level measuring instrument with a maximum measuring distance of up to 80 meters. The antenna is further optimized, and the new type of microprocessor can be used for higher speed signal analysis and processing, so that the instrument can be used in some complex measuring conditions, such as reactor, solid silo and so on. 2.principle The radar level antenna transmits narrower microwave pulses, which are transmitted downwards through the antenna. When the microwave touches the surface of the measured medium, it is reflected back and received again by the antenna system, which transmits the signal to the electronic circuit and automatically converts it into a bit signal (because the microwave propagates very fast, The time it takes for an electromagnetic wave to reach the target and return to the receiver through reflection is almost instantaneous). NYRD 807 For use: sanitary liquid storage containers, strongly corrosive containers Measurement range: 20 m Process connections: flange Medium temperature:-40 �°C 150 â?? Process pressure:-0.1~0.1MPa Fine degree: equal to 3 mm Level of protection: IP67 Frequency range: 26GHz Explosion proof grade: Exia C T6 Ga/Exd ia IIC T6 Gb Signal output: 4.20mA/HART (2 / 4)RS485/Mod bus
6GHz intelligent radar level gauge is suitable for non-contact continuous measurement of liquid, slurry, granular and bulk materials. It is suitable for temperature, pressure change, inert gas and volatilization. The measurement method of microwave pulse is adopted, and it can work normally in the range of industrial frequency band. Low beam energy, can be installed in a variety of metal, non-metal containers or pipes, no harm to the human body and the environment. Application:Simple corrosive liquid in the process Skyline:PTFE Measuring range: 20 meters Frequency range: 6.8GHz Accuracy: 0.1%FS Medium temperature: -40 to +130 °C Process pressure: -0.10.3Mpa Power supply: 24vDC (two-wire, four-wire optional) Signal output: 4...20mA/HART (two lines/four lines)/ RS485/Mod bus Process connection:Thread Protection level: IP67 Explosion-proof grade: Exia IIC T6 Ga
Design features Guided wave radar level gauge adopts advanced microwave processing technology and unique Echo Discovery echo processing technology. Contact measurement has high accuracy and more accurate measurement. At the same time, guided wave radar is anti-adhesion, not affected by external environment such as medium temperature and adhesion. The 70X series guided wave radar level gauge is suitable for various complex working conditions and application occasions due to various process connection modes and detection components. For example, high temperature, high pressure and low dielectric constant medium, etc. Using pulse mode, the product can be installed in all kinds of metal and non-metal containers with very low emission power, which is harmless to human body and environment. 3. Technical parameters Application:Liquid, Powder, Solid particles Antenna material:304/PTFE/Flexible cable Measuring range: 30 meters Frequency range: 1.8GHz Accuracy: ±1mm Medium temperature: -40 to +130 °C;-40 to +250 °C Process pressure: -0.1ï½?4.0Mpa Power supply: 24vDC (two-wire, four-wire optional) Signal output: 4...20mA/HART (two lines/four lines)/ RS485/Mod bus Process connection:Thread Protection level: IP67 Explosion-proof grade: Exia IIC T6
High Frequency Radar Level Meter Design features: Small antenna size, easy to install; non-contact radar, no wear, no pollution Hardly affected by corrosion or foam; hardly affected by changes in water vapor, temperature and pressure in the atmosphere. Severe dust environment has little influence on the work of high frequency level gauge. Shorter wavelength, better reflection on inclined solid surfaces The beam angle is small and the energy is concentrated, which enhances the echo ability and helps to avoid the interference. The measurement blind area is smaller, and good results can be obtained for small tank measurement. High signal-to-noise ratio, even in the case of switching, can achieve better performance High frequency is the best choice for measuring solid and low dielectric constant medium Application: various corrosion liquid Antenna material: PTFE Measurement range: 10 m Process connection: thread, Flange Medium temperature: -40C --130 Process pressure:-0.1~0.3MPa Accuracy: ±5mm Power supply: 24VDC (two lines, four lines) Protection grade: IP67 Frequency range: 26GHz Explosion-proof grade: Exia C T6 Ga/ Exd ia IIC T6 Gb Signal output: 4. 20mA/HART (two / four) RS485/Mod bus
Air compressors, automation equipment, bearings, cables, diesel engines and generators & machinery spare parts, filters, electrical equipment's, electric motors and gear motors, panel boards and & much more..Logistics, customer clearance and much more.
Desulphurisation Slag is an iron slag derived from the desulphurisation skimming process. This material is an iron by- product that is encapsulated in varying levels of contaminants (S,Mg,Si), but has a stable chemistry with 75 -80% chemistry. The level of Fe% in the slag has been estimated by water displacement test. This material con offer competitive advantages respect other metal scraps: Price; Stable Chemistry; The material can be loaded loose in 20 heavy duty container. For further details feel free to contact us.
We are proposing about 1000 1200 Mt/ton monthly of iron slag derived from the desulphurisation skimming process. This material is a iron by- product that is encapsulated in varying levels of contaminants (S,Mg,Si). In order to enhance its usability, the material is processed and screened. We can propose two specifications of Iron Slag : 1. >85% Fe Average 600mm Max Fraction 2. >78% Fe Average 20-300mm Fraction The level of Fe% in the slag has been estimated by water displacement test. For any further information please feel free to contact
We are proposing about 2000tons of iron slag derived from the desulphurisation skimming process. This material is a iron by- product that is encapsulated in varying levels of contaminants (S,Mg,Si). In order to enhance its usability, the material is processed and screened. We can propose two specifications of Iron Slag - European Code: 19.12.01 - Basel Code: B1010 - HS Code: 2619.0020 - Quantity: 2000 tons currently available - Monthly quantity: 500-1000 tons depending on production - Size: 350 1200 mm - Fe content: from 77 to 86% - C content: above 2,5-3% - Bulk density: 2,8-3,4 tons/m3 - Loading type: loose in 20 (26-27 tons on average) The level of Fe% in the slag has been estimated by water displacement test. For any further information please feel free to contact us
