Main parameters: Item 0.96 inch TFT LCD display Model nameTST09601A Display ModeNormally White,Transmissive Resolution80*160 Technology Typea-Si TFT active matrix Driver ICST7735S Pixel ConfigurationR.G.B. Vertical Stripe Outline Dimension13.3(W) x 27.948(H) x 1.4(D) Active Area(mm)10.8 (W) x 21.7 (H) InterfaceSPI Viewing DirectionFREE Surface treatment:Anti-Glare Backlight Type1-LED white color Operating Temperature-20~70°C Storage Temperature-30~+80°C
LCD type TFT, Transmissive Display type 4.3 inch TFT lcd , 262k color, normal white Driver element a-si TFT Active matrix Outline Dimension(mm) 105.5x67.2x3(without touch panel) A.A.(mm) 95.04x53.856 Driver IC HX8257A Item QVGA 3.5 inch tft lcd display Resolution(dots)_ 480*272 Viewing Direction 12H Operating temperature(°C) -20-70 Storage temperature(°C) -30-80 Number of Pixel(pixels) 480(H)x 3RGB x 272(V) Dots Pitch 0.18x0.18 Operating Volatge 3.2v Pixel arrangement RGB Vertical Stripe Display mode Normally white Surface treatment Antiglare, Hard-Coating(3H) Weight(g) TBD Backlight 10LEDs, White Weight(g) TBD Interface RGB24bit Module lifetime(Hours) 50,000-100,000
LCD type TFT, Transmissive Display type 3.5 inch TFT lcd , 262k color, normal white Driver element a-si TFT Active matrix
LCD type TFT, Transmissive Display type 2.0 inch TFT lcd , 262k color, normal white Driver element a-si TFT Active matrix Outline Dimension(mm) 37.88x51.5x2.5(without touch panel) A.A.(mm) 30.6x40.8 Driver IC ILI9341 Item TFT 2.0 inch lcd display Resolution(dots)_ 176*RGB*220 Viewing Direction 6H Operating temperature(°C) -20-70 Storage temperature(°C) -30-80 Number of Pixel(pixels) 176(H)x 3RGB x 220(V) Dots Pitch 0.18x0.18 Operating Volatge 3.2v Pixel arrangement RGB Vertical Stripe Display mode Normally white Surface treatment Antiglare, Hard-Coating(3H) Weight(g) TBD Backlight 3LEDs, White Weight(g) TBD Interface 8BIT MCU interface Module lifetime(Hours) 50,000-100,000
LCD type TFT,Transmissive Display type 1.44 inch tft lcd module , 65k color Driver element a-si TFT Active matrix Outline Dimension(mm) 32.35x38.0x2.6 A.A.(mm) 25.5X26.5 Driver IC ST7735S Resolution(dots)_ 128*RGB*128 Viewing Direction 12H Operating temperature(°C) -20-70 Storage temperature(°C) -30-80 Number of Pixel(pixels) 128 x RGB x 128 Operating Volatge vdd=2.8v Pixel arrangement RGB Vertical Stripe Display mode Normally white Surface treatment Antiglare, Hard-Coating(3H) Weight(g) TBD Backlight LED, White Weight(g) TBD Interface 8080 system 8 bits parallel interface Module lifetime(Hours) 50,000-100,000
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
Technical Specifications MTK 6580 Quad Core 1GB, 8GB EMMC 7 inch Capacitive Touch Screen Display 80mm built-in Thermal & Lablel Printer Dual SIM Cards, Support Micro TF Card Including NFC and IC card (optional) Charging Dock Stand Black, White and Red Colors Can be used as Standalone Cash Register Product Name HDD-A7 Material Plastic and iron Function Android/Linux POS System, Cash Register Package Standard Export CartonSize: L 32cm* W 17cm* H 15cm Weight: 1.383 kg
2-head packaging machine (also can 4-18head according different capacity choice) Packaging speed 15bags/min Bag length 90-320mm Bag width 80-210mm Overall weight 400kg Power 1.8kw/220v Packaging capacity 20-1000ml Outer packaging size 820 x1220 x 2500mm Packaging form Back sealing This machine is an intelligent weighing automatic quantitative packaging machine with four scales and microcomputer control. Suitable for quantitative packaging of granular materials such as miscellaneous grains, nuts ,pesticides, fertilizers, veterinary drugs, premixes, additives, laundry detergent, salt, monosodium glutamate, white sugar, seeds, rice, snacks, hardware, etc. Performance characteristics: 1. High precision digital sensors enable precise measurement to be achieved instantly. 2. The microcomputer control system is technologically advanced, easy to operate, and more reliable to use. 3. Fast and slow vibration feeding, automatic correction of errors, achieving high-precision packaging. 4. Four scales work alternately, with fast packaging speed. 5. High quality stainless steel is used for the material contact part, which is anti-corrosion, dust-proof, and easy to clean. Host configuration: This machine is equipped with a dual CPU microcomputer control system, a 5-inch LCD display in Chinese or English, a user-friendly operation interface, automatic cursor detection and tracking, and simpler operation. Equipped with high-precision stepper motors to ensure the accuracy of the cutting position of each packaging bag.
Type: TFT Display Size: 5 inch tft lcd Supplier Type: Manufacturer Resolution: 800xRGBx480 Interface: TTL Viewing Angle: 12 O'clock LCM(mm): 120.7(W) Active Area(mm): 108.00x64.80 Color Depth: 16.7M Driver IC: ILI5480 1/ILI6123H 2 & Compatible LDI LCD Type: a-si TFT, Transmissive, normally White, TN Operating Temperature:
ITO GLOBAL, SURAT, GUJARAT ( India ) We can supply high strength, quality tested and recyclable fresh PP VOVEN bags of size 29x43 inch , for filling grains (like wheat) up to 25-50-100 kgs with UV protection, BAGS Weight- as per customers requirements. as a replacement for costly Jute Bags, in packaging of 500 bags/bale with compressed packaging to save logistics costs. Size can be customized as per requirement. Also, available in transparent, milky white and colors. Bag Specification 1. Bag Size 29 x 43 inch ( 74 cm x 110 cm) 2. Bag weight 155 grams / PC (2% tolerance) 3. Mesh 11 x 11 4. UV rays protection 5. Flexible bag 6. Packaged in moisture proof and compressed bales of 500 Bag Pieces / bale 7. Estimated rates as mentioned. 8. Rates are for FOB, CIF, CFR Basis, Hazira, India. We can supply across any major port on CIF basis. 9. Samples are available.
ITO GLOBAL, SURAT, GUJARAT ( India ) We can supply high strength, quality tested and recyclable fresh PP bags of size 29x43 inch , for filling grains (like wheat) up to 25-50-100 kgs with UV protection, BAGS Weight- as per customers requirements. as a replacement for costly Jute Bags, in packaging of 500 bags/bale with compressed packaging to save logistics costs. Size can be customized as per requirement. Also, available in transparent, milky white and colors. Bag Specification 1. Bag Size 29 x 43 inch ( 74 cm x 110 cm) 2. Bag weight 155 grams / PC (2% tolerance) 3. Mesh 11 x 11 4. UV rays protection 5. Flexible bag 6. Packaged in moisture proof and compressed bales of 500 Bag Pieces / bale 7. Estimated rates as mentioned. 8. Rates are for FOB, CIF, CFR Basis, Hazira, India. We can supply across any major port on CIF basis. 9. Samples are available.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Packing : I/F / Black Grade : 3/5 inch, 5/7 inch
Origin: USA Material: PMMA Regrind Clear/Injection grade Category: PMMA Type: Regrind Color: Clear Grade: Injection grade Quantity: 6 Tons Loading weight:21 Tons Specification: "PMMA combine load: - 5 Tons of black & 2tons mix colour regrind from Car part Injection grade - 6 tons of Natural regrind from Car part Injection grade - 8 tons of LCD Sheet extrusion grade Subject to unsold" Thanks for contacting us! We are selling CFR term, Incoterms 2020. Payment term: 50% advance, balance against copy Bill of Lading Could you please give us more details about your company and demand for us to offer you the suitable material? 1.What is your company name and address? 2.Have you imported this material before? 3.If yes, which is your port of destination and HS code which you use to import this material? 4.How many tons do you need per month? 5.Which grade and color are you looking for? 6.Do you prefer us to contact you via email or whatsapp, wechat, skype,..?
Properties 1. Excellent transparency, outstanding resistance to aging. 2. It has good insulating properties and mechanical strength; to acid, alkali, salt has a strong resistance to corrosion; and because easy processing. Applications 1.Extruded sheets for signage, displays and building material 2.Motive parts such as tail lamps, meter covers and sun visors 3.General sundries such as tableware, kitchenware, giftware and bathroom accessories 4.Optical lenses such as sunglasses, reading glasses and camera lenses 5.Light guide panels for LCD displays 6.Other applications such as mobile phone display panels, clock covers, lighting covers/accessories, optical fibres, toys, etc.
Properties 1. Excellent transparency, outstanding resistance to aging. 2. It has good insulating properties and mechanical strength; to acid, alkali, salt has a strong resistance to corrosion; and because easy processing. Applications 1.Extruded sheets for signage, displays and building material 2.Motive parts such as tail lamps, meter covers and sun visors 3.General sundries such as tableware, kitchenware, giftware and bathroom accessories 4.Optical lenses such as sunglasses, reading glasses and camera lenses 5.Light guide panels for LCD displays 6.Other applications such as mobile phone display panels, clock covers, lighting covers/accessories, optical fibres, toys, etc.
Properties 1. Excellent transparency, outstanding resistance to aging. 2. It has good insulating properties and mechanical strength; to acid, alkali, salt has a strong resistance to corrosion; and because easy processing. Applications 1.Extruded sheets for signage, displays and building material 2.Motive parts such as tail lamps, meter covers and sun visors 3.General sundries such as tableware, kitchenware, giftware and bathroom accessories 4.Optical lenses such as sunglasses, reading glasses and camera lenses 5.Light guide panels for LCD displays 6.Other applications such as mobile phone display panels, clock covers, lighting covers/accessories, optical fibres, toys, etc.
Properties 1. Excellent transparency, outstanding resistance to aging. 2. It has good insulating properties and mechanical strength; to acid, alkali, salt has a strong resistance to corrosion; and because easy processing. Applications 1.Extruded sheets for signage, displays and building material 2.Motive parts such as tail lamps, meter covers and sun visors 3.General sundries such as tableware, kitchenware, giftware and bathroom accessories 4.Optical lenses such as sunglasses, reading glasses and camera lenses 5.Light guide panels for LCD displays 6.Other applications such as mobile phone display panels, clock covers, lighting covers/accessories, optical fibres, toys, etc.
No.ItemSpecification 1LCD size4.3 inch(Diagonal) 2Driver elementTFT active matrix 3Resolution480RGBx272 4Display modeTransmissive 5Active area95.04(W) Ã? 53.86(H) mm 6Module size105.5(W) Ã? 67.2(H) Ã? 2.95(D) mm 7Color arrangementRGB-stripe 8Viewing Direction6 o'clock 9Brightness250 cd/m2 (can make 500cd/m2) 10InterfaceRGB 11Contrast ratio500 12Touch panelOptional (capacitive touch or resistive touch) 13Driver ICILI6480BQ or Eqv. 14Operating temperature-20ºC~+70ºC 15Storage temperature-30ºC~+80ºC
FINGERTIP PULSE OXIMETER Parameters: Two parameters:SPO2, Pulse Rate. Waveforms: SpO2 Waveform. Features: 1 COLOR OLED display, four direction adjustable. 2 SpO2 and pulse monitoring, and Waveform display. 3 With menu operation. 4 With beep and alarm. 5 Low-power consumption, continuously work for 50 hours. 6 Small in size, light in weight, and convenient to carry. 7 Low voltage alarm display, Auto power-off. 8 Runs on standard AAA batteries. Detailed descriptions of product functions: SPO2: 1 Measurement range: 70%-99% 2 Accuracy: �±2% on the stage of 70%-99%, unspecified(
