The Semiconductor Optical Amplifier Devices at 1310nm and 1550nm are designed by using a high quality angled SOA chip and a TEC which can assure a stable amplified output for a large dynamic input signal. The devices are available in a standard, 14-pin butterfly package at the 1310nm and 1550nm bands. The SOA devices have high optical gain, high saturation output power, low polarization dependent loss, low noise figure and broad wavelength range. We have options of optical isolators for input and/or output side as well as output fibers of SM fibers, PM fibers and other special fibers per customer specifications. The products are Telcordia GR-468 qualified, and in compliance with RoHS requirement.
HTF launched SOA series optical amplifier products can be 1290nm ~1320nm wavelength range to achieve amplification. It can be easily used in 100G transmission system, the maximum can support 160G/s rate. SOA optical amplifier can be used for booster amplification, pre-amplification and other occasions. O-band optical signal overall amplification Covering the wavelength range of 1290 ~ 1320nm 100G 1310nm signal amplification Support O-band, 1290 ~ 1320nm band amplification Output power up to 10dBm 100G 1310nm signal amplification Support APC Low noise, high gain One board supports up to 2 channels of signal amplification
Amplifiers Packing in cartons.40" high cubic. Shipment by sea form Mumbai / jnpt port India.
Features: 1.built in adjustable Gain & Slope 2. Built in power supply 3. Connectors:"F"type female 4. Output test point and screw terminal for equippotential bonding 5. Metal-Plastic Housing For indoor mounting Specifications: ModelAS205S No.of Inputs3UHF, 1BIII, 1BI+FM No.of Outputs2 Frequency UHF1: (MHz)470óª862 UHF2: (MHz)470óª862 UHF3: (MHz)470óª862 BIII: (MHz)174óª230 BI+FM: (MHz)47óª68/88óª108 Gain(UHF1,UHF2,UHF3,BIII,BI+FM) (dB)20 Output Level(UHF1,UHF2,UHF3,BIII) (dBuv)115 BI+FM: (dBuv)110 Slope Adj. (dB)20 Slope Adj.ú¼Typical (dB)15 Return Loss (dB)_óª12 Noise Figure (dB)
We are the authorised dealers for "amperes"-known for its complete range of equipments in conventional public address systems in india. The iso9001: 2000 certification that amperes obtained in 2006 for "design and manufacturing of public address system" only demonstrates full commitment in producing the most optimum and affordable equipments for our customers. Amperes has been directly involved in thousands of installations, be it small or large, simple or complex, part or full systems at airports, hospitals, government offices, recreation facilities, hotels, schools, universities, shopping malls and hundreds of other public spaces. Amperes is present in the following locations worldwide: singapore, brunei, uae, vietnam, sri lanka, india, philippines, indonesia, myanmar and thailand.
Features: High power round transformer, low work noise, Low magnetic leakage, high efficiency Device infixed to prevent front thunder and over voltage Automatic over current and short circuit Automatic reset circuit. Sound Light alarm Inside power Plug-in and tree- way feed output Ranging from 3Amps to 10Amps. Technology Parameter Item UnitForwardRemark FrequencyMHZ5-1000 Input voltageAC220í+10% Output voltageAC60v í+ 10% Plugging lossDB< or =0.5 Return lossDB>15 Return timeS5 í+5 Max output current Sum of all output current must be under the MAX current VolumeMn270mn*195 Dimensionsmm268*212*197 WeightKGS6.7.
Amplifier
Amplifier Parameters unit p-pa1200 p-pa1500 p-pa2500 p-pa3500 Output power stereo @ 8 ohm watt 2x400 2x550 2x700 2x1000 Output power stereo @ 4 ohm watt 2x600 2x800 2x1100 2x1500 Output power bridged @ 8 ohm watt 1000 1500 2000 2800 Frequency response hz 20hz-20khz; +0.1/-0.3db (1w / 8 ohm) T.H.D db
EDFA Optical Amplifier module provide multi-function, low noise, Erbium-Doped Fiber Amplifier (EDFA) solutions, The amplifier module can be operated at constant gain (Automatic Gain Control AGC), constant output power (Automatic Power Control, APC). Integrated VOA can be automatically adjusted to achieve smooth gain spectrum. It can amplify the C-Band signal with or w/o middle stage access (MSA), which brings great flexibility for the network application. FUNCTIONï¼? C-band optical signal overall amplification Covering the wavelength range of 1528 ~ 1565nm Support systems to achieve different cross-section radio repeater transmission HIGHTLIGHT: Wide operating wavelength range:1528nm~1565nm Three Optical Amplifier C-Band applications: Booster , In-line, Pre-amplifier Low noise figure: typical: 5dB Excellent gain flatness Multiple operating modes: AGC adjustable Gain APC output is adjustable ACC voltage adjustable Mid-stage access for DCM or OADM Optional OSC channel for remote management MON port, on-line monitoring optical power and OSNR Many model options serve all the traditional amplifier applications in an extended optical link: booster, in-line, and pre-amplifier. A booster amplifier operates at the transmission side of the link. It features high input power, high output power, and medium optical Gain . Boosters are designed to amplify aggregated optical input power for reach extension. An in-line amplifier operates in the middle of an optical link. It features medium to low input power, high output power, high optical Gain , and a low noise figure. In-line amplifiers are designed for optical amplification between two network nodes on the main optical link. A Pre-amplifier operates at the receiving end of an optical link. It features medium to low input power, medium output power, and medium Gain. Pre-amplifiers are designed for optical amplification to compensate for losses in a demultiplexer located near the optical receiver. Some EDFA Models include an additional mid-stage port designed for insertion of a Dispersion Compensation Management (DCM) unit without its inherent insertion loss. The design of these models maximizes the DCM benefits to increase deployment flexibility. New placement options require fewer amplifiers in the link, and they can open the door to applications that were not possible with older technology.
EDFA Optical Amplifier 1U Rack EDFA is the erbium-doped fiber amplification board. Its main function is to compensate the power of the signal optical in the transmission line, and it can amplify the optical signals of up to 48 channels with 100 GHZs interval) or 96 channels with 50 GHZ s interval) at C band at the same time. It has characters of flat gain, locked gain, low noise index, etc. It's an indispensable and important component for DWDM system, future high speed system and all-optical network long-distance transmission.
EDFA optical amplifier module provide multi-function, low noise, Erbium-Doped Fiber Amplifier (EDFA) solutions, The amplifier module can be operated at constant gain (Automatic Gain Control AGC), constant output power (Automatic Power Control, APC). This is a highly integrated EDFA, and the large module supports Dual amplifier with two independent gain units . Wide operating wavelength range:1528nm~1565nm Dual amplifier contains two independent gain units Low noise figure: typ 5dB Excellent gain flatness Multiple operating modes: AGC adjustable Gain APC output is adjustable Optional OSC channel for remote management MON port, on-line monitoring optical power and OSNR
EDFA optical amplifier module provide multi-function, low noise, Erbium-Doped Fiber Amplifier (EDFA) solutions, The amplifier module can be operated at constant gain (Automatic Gain Control AGC), constant output power (Automatic Power Control, APC). This is a highly integrated EDFA, and the large module supports Dual amplifier with two independent gain units . Wide operating wavelength range:1528nm~1565nm Dual amplifier contains two independent gain units Low noise figure: typ 5dB Excellent gain flatness Multiple operating modes: AGC adjustable Gain APC output is adjustable Optional OSC channel for remote management MON port, on-line monitoring optical power and OSNR
Single Fiber Bidirectional EDFA Amplifier models include a Red and a blue port designed for single fiber DWDM Solution. The design of these models is used for single-fiber DWDM transmission systems. C-band optical signal overall amplification Covering the wavelength range of 1528 ~ 1561nm Support systems to achieve different cross-section radio repeater transmission Operating wavelength range: Blue: 1528nm~1543nm Red: 1547nm~1561nm Low noise figure: typ 5dB Excellent gain flatness Multiple operating modes: AGC adjustable Gain APC output is adjustable ACC voltage adjustable Mid-stage access for DCM or OADM Offset the insertion loss introduced by DCM Reduce the additional degradation of system OSNR Flexible insertion of DCMs at different distances Optional OSC channel for remote management MON port, on-line monitoring optical power and OSNR Single fiber bidirectional EDFA amplifier include an Red and blue port, Red optical amplifier include an blue out port and blue in port, Red optical amplifier Amplify red optical signal, blue out port and blue in port are used to access the amplifier to amplify the blue optical signal. Blue optical amplifier include an red out port and red in port, Blue optical amplifier Amplify blue optical signal, red out port and red in port are used to access the amplifier to amplify the red optical signal, Blue: 1528nm~1543nm. Red: 1547nm~1561nm.
The vp series power amplifier offers clean, reliable power in a durable enclosure. If you need professional amplification performance, the vp series is perfect for delivering pure, consistent wattage night after night. With six models power upto 1200 watts, the vp series is ideal for powering pa systems and dj rigs. To ensure seamless, reliable performance, the amp features variable-speed cooling fans for thermal stability, along with short-circuit, thermal, over current, thermal protection. For connecting convenience, the vp series boasts xlr and speakon &banana binding post outputs. The unit also provides front panel indicators for signal, limit, protect and power, plus level controls for channels 1 and 2. Selectable modes for stereo and mono bridge give you even more flexibility. Selectable output power range to drive professional loudspeakers without clipping Variable-speed cooling fan for thermal stability and reliability Xlr balanced inputs and speakon &banana binding post outputs Limiter indicator for amp output protection Stereo and mono bridge Variable speed fan for low noise Comprehensive front panel indicators including signal, limiter, protect and power Dc output protection and short circuit protection Frequency response 10hz c 50khz at 1.5 db Total harmonic distortion: less than 0.05% Input sensitivity & impedance: 0.775v Signal to noise (20 hz - 20 khz) > 95db Shipping dimensions (wxdxh) 585x 580 x 165mm
With the application of long-distance systems becoming more and more extensive, our company's self-developed middle stage access (MSA) EDFA, middle stage access (MSA) EDFA can effectively solve the insertion loss caused by DCM and OADM, offset the DCM and OADM bands. The resulting insertion loss reduces the additional degradation of the system OSNR. C-band optical signal overall amplification Covering the wavelength range of 1528 ~ 1565nm Support systems to achieve different cross-section radio repeater transmission Wide operating wavelength range:1528nm~1565nm Low noise figure: typ 5dB Excellent gain flatness Multiple operating modes: AGC adjustable Gain APC output is adjustable ACC voltage adjustable Mid-stage access for DCM or OADM Offset the insertion loss introduced by DCM Reduce the additional degradation of system OSNR Optional OSC channel for remote management MON port, on-line monitoring optical power and OSNR Middle stage access (MSA) EDFA models include an additional mid-stage port designed for insertion of a Dispersion Compensation Management (DCM) unit without its inherent insertion loss. The design of these models maximizes the DCM benefits to increase deployment flexibility.New placement options require fewer amplifiers in the link, and they can open the door to applications that were not possible with older technology.
output power RMS): 150W +150W 4 with BLUETOOTH function with USB/SD & FM function 6 MIC input double 10-band graphic EQ Panel size(LxH): 48.3x 22(cm) 430*380*22MM 11KG
output power: 60W output mode: 4-16ohm/70v/100v with USB/SD & FM function remote control with BLUETOOTH function independent control or left and right sound volume 2 MIC input Panel size(LxH): 28x 6.5(cm) Size:280*205*65mm
"FAMAGA Group OHG, the global supplier of industrial equipment and spare parts, is glad to provide encoders by Amplifiers Keyence: We supply a complete range of the manufacturerâ??s catalog, including the following items: Keyence CZ-V21AP Keyence FS-N11CP Keyence PZ-G42CB Keyence FU-6F Keyence LV-H42 Keyence FS-N11P Keyence FS-V31CP Keyence LR-ZB250CP Keyence CZ-H32 Keyence LR-ZB100CP Keyence IL-300 Keyence CZ-H37S Keyence FU-35FZ Keyence LV-21AP Keyence LV-N11P Keyence PZ-G42P Keyence PZ-V12P Keyence OP-87441 Keyence FU-40 Keyence FS-V11 Keyence PZ-B02 Keyence PZ-B04 Keyence IL-1000 Keyence SR-1000 Keyence SZ-16V Keyence OP-87458 Keyence IV-2000MA Our company is also pleased to offer products of other brands: Bei Sensors IBH Softec Schmersal BALLUFF Pepperl+Fuchs Bernstein Di-Soric Elobau Univer Eltra Aventics FESTO Camozzi Euchner END-Armaturen TAMAGAWA SENECA Airtac Murrelektronik Azbil Yamatake FRANKE-Filter Endress+Hauser IFM Ipf Electronic Kieback & Peter MD Micro Detectors Bihl Wiedemann ANDERSON-NEGELE KITAGAWA Georg Schlegel Metal Work Kipp Allen-Bradley Netter Vibration Kuebler / K�¼bler RAFI LINDY 4B Braime SOUTHCO ELGO Electronic FAG RECO Pilz AIRTEC Pneumatic COMITRONIC-BTI L�¼tze Hydac Barksdale Keyence AirCom Pneumatic Garlock Mac Valves MAHLE (Filtration Group) Riegler Baumer Elreha Sick Siko FAMAGA Group OHG is a family-owned company with many years of experience in the supply of components and spare parts for industrial enterprises around the world. Our mission is to provide fair prices, reducing the cost of production for our customers. A significant network of suppliers around the world allows us to supply any equipment, which client needs on favorable terms. Therefore, the list of equipment we provide is tenfold greater than the catalog presented on this site. You are welcome to check the full catalog on our website."
Aluminum front panel, toroidal transformer Dual-10 phase eq, 6 way microphone inputs Usb/sd card slot support mp3/wma audio files, led display, fm tuner, remote control 515*420*770mm, 3sets per ctn
Class ab ( 2/4/5/6 channel amplifiers ) Class d ( 500w up to 7000w ) Full mosfet & etc. Standard export packing system