Saturated Polyester Resin 2 Pack Polyurethane Suppliers and Manufacturers

We supply high grade face veneer or core veneer. Wood species available: eucalyptus, acacia, poplar, keruing, okume, birch, pine etc. Our core veneer can be used for commercial grade plywood, film faced plywood, packing plywood. 1.Rotary cut : 1,270 x 640 x 1.0MM, OR 1.7mm 2.Sliced cut: 1270x Width 60mm upward , 0.45mm upwards 3.Thickness Tolerance: -0.03, + 0.05 4.Content Moisture: 18 % max 5.Drying process; Sundry or oven dry. 6.Cutting Process: Rotary Cutting/ Sliced cutting Grade A: 1. Full sheet of same color, no dead knot and small hole. No tear, No Joints 2. Whole piece (no joints) with live knots, limited dead knots, some small holes not more than 2cm in diameter. Also available in mix of grade A and B We can supply in following grade 1Grade A: 100% 2Grade A :90%+ Grade B:10% 3Grade B: 100%

Name : Weed control mat/Ground cover/ 1. Weight 2oz/sm - 14oz/sm or 60gsm-150gsm 2. Width 1.6' -20' or 0.5m-6m 3. Roll Length 16', 33', 65', or 5m,10m,20m,25m,50m,100m or as required 4. Color Black,Green,Black-green or as required 5. Weave 8*8,10*10,11*11,12*12,12*16 6. Material 100% PP material 7. UV resistance 3-5 years 8. Sample Avaliable 9. Delivery time About 20 days 10. Min order No limit 11.Terms of payment 1.TT or LC 12. Supply capacity 500 tons per month 13. Packing In rolls with paper core inside and polybag outside or in Carton or as your request 14. Quantity 1x20ft container can load about 11 tons 1x40'HC can load about 26 tons 15.Export market Australia,Canada,Argentina,USA,The Middle East,Europe market ,Japan and so on.

2N 1N FREE toothbrushes in a blister pack 90 such packs in a case 40 such cases on a pallet pallet size 120 x 100 x 135 by air OR 72 such cases on a pallet pallet size 120 x 100 x 231 by sea OR 750 such cases direct on floor without pallet in a 20 dry container OR 1575 such cases direct on floor without pallet in a 40 dry container OR 1925 such cases direct on floor without pallet in a 40 HC dry container

-SCHICK Exacta 2 sen 2+1 [3 pcs x 12 pack x 12 =432pcs] -SCHICK Exacta 2 women 2+1 Pink [3 pcs x 12 pack x 12 = 432pcs] -SCHICK Exacta 2 sen 5+2 [7 pcs x 12 x 1 = 84pcs] -SCHICK Xtreme 3 Men Disposable 2+1 [3 pcs x 6 bags x 10 = 180pcs] -SCHICK Xtreme 3 comf + Wom 4''s HT [4 pcs x 6 pack x 12 = 288pcs]

Granulated Instant coffee, produced by Nestle Indonesia. Packed in 2 Gram net weight coffee in single serve sachet. 60 sachets per bag 10 bags per carton

We deals in the following products :- 1) PVC Resin 2) Caustic Soda Flakes

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.

Each razor with 2 platinum coated blades and plastic cap 5 such razors in a pouch pack 12 such pouch packs in an inner carton 12 such inner cartons in a case i.e., 144 packs or 720 razors in a case 24 such cases on a pallet (pallet size 120 x 100 x 147) by air OR 40 such cases on a pallet (pallet size 120 x 100 x 235) by sea OR 520 such cases without pallets, direct on floor in a 20' dry container OR 1,050 such cases without pallets, direct on floor in a 40' dry container OR 1,260 such cases without pallets, direct on floor in a 40' HC dry container.

Color index, number : 18 Hot alcoholInsolubile,% : 1.00 Application: 1. The plasticity and castability of heating, combined with its ability to absorb a large amount of infiltrated material, is of great value in the casting industry. 2. The lac resin is non-toxic. Based on the excellent characteristics listed above, the shellac resin is applied to alcohol paints, electrical insulating materials, printing inks, rubber fillers, and its use for oil and acid resistance. 3. Other industries: It has a wide range of important application value in many fields such as medicine, food, cosmetics, chemical industry, metallurgy, machinery, woodware, papermaking, electronics and military industry.

Giva Agro's Pure Shilajit Resin is the closest natural form of Shilajit. Apart from following an ayurvedic purification, no chemical or other outside ingredient is added. That is what makes resin the most potent form of shilajit. Other names of shilajit : Shilajeet, salajit, shilajatu, mimie, or mummiyo, mumijo Properties: Fulvic acid,Humic acid,Selenium Botanical name: Asphaltum punjabianum Product : Pure shilajit resin Form available: Resin/Semi Liquid Country of Origin: Himalayas, Made in India Speciality: No sugar, No Preservatives, No artificial color or harmful Chemical added. Non GMO, Gluten Free, Does NOT Contain Soy, Gelatin, Egg, Dairy or Caffeine, No Additives or Fillers Benefits of Shilajit: 1.Provides energy and revitalisation 2.Regulates hormones and immune system 3.Alleviates pain response 4.Helps with weight loss 5.May help manage Diabetes 6.Promotes healthy metabolism 7.Fights inflammation and builds immunity 8.Potentially aid in breaking of addictions. To have our own private labelled Shilajit,

Quality: 1st Grade Size: 40/50, 50/60, 60/70, 70/80, Aflatoxin Max 4ppb Damaged Max 2% Packing: PP Bagsp/25/50kg Season: April - November Origin: Argentina, Paraguay Annual production volume: 3000ton Container capacity: 25-26ton

Quality: 1st Grade Size : 185-200 Wrinkled Max.2% Admixture Max 1% Damaged Max 3% Packing : PP Bags p/25/50kg Season : August - December Origin : Argentina Annual production volume : 300 Ton Container capacity : 24ton

Abrasive Garnet produced from River from India in All Grades.

Available Production Waste, Available Washed and Trimmed, Non Washed packed in Bales. European Origin

Memory/Viscose Elastic Foam Scrap. AA Grade only White in color. Post Production.