Rongsheng F1600 Mud Pump Crosshead Product Description The crosshead supplied by Lake Petro is manufactured from high quality, cast steel and the guides are from a quality manganese bronze normally used in bearings. This combination of materials provides a low friction interface and generates very little heat, which indications no friction, which equates to no wear. Lake Petro has very rich experience in supplying spare parts of mud pump to the worldwide Oil Drilling industry.We stock and sell a wide selection of mud pump fluid end expendables and spares parts. Mud pump parts for F series mud pump, For P series mud pump, For PZ series mud pump, For 3NB series mud pump. These parts include liners, pistons, valves & seats,piston rods, rod clamps, extension rods, all fluid end seals and gaskets, fluid cylinder modules and accessories, as well as power end components, such as crankshaft assemblies, gear sets, connecting rods, crosshead, and bearings.
Description: F1600 pump unit is used for transporting high viscosity, large proportion, higher sediment concentration Drilling fluid to the well bottom in high pressure, for cooling the bit, wash the bottom, break the rock, and Carry out rock cutting when return from the well bottom. It is one the main process equipment of oil drilling Operation. F1600 electric pump unit is consist of mud pump, dc motor, small base, big base, belt transmission system, spray system, pressure relief manifold and charging system etc. Dc motor is installed on independent skid, and fixed integrally on the big base behind the f1600 pump. Motor power is transmitted to mud pump from input shaft by belt, then drive the mud pump. Small base is equipped with a regulating screw, which can adjust the elasticity of belt. The matching electric spray pump is used to cool hydraulic end piston, cylinder liner, thus to make sure they work properly. Api standard F1600 pump unit meets the requirements of api 7k drilling and wellhead equipment Operation specifications and sy/ t5138 standards.
Cheaper crosshead for mud pump Product description The crosshead supplied by lake petro is manufactured from high quality, cast steel and the guides are from a quality manganese bronze normally used in bearings. This combination of materials provides a low friction interface and generates very little heat, which indications no friction, which equates to no wear. Lake petro has very rich experience in supplying spare parts of mud pump to the worldwide oil drilling industry.We stock and sell a wide selection of mud pump fluid end expendables and spares parts. Mud pump parts for f series mud pump, for p series mud pump, for pz series mud pump, for 3nb series mud pump. These parts include liners, pistons, valves & seats, piston rods, rod clamps, extension rods, all Fluid end seals and gaskets, fluid cylinder modules and accessories, as well as power end Components, such as crankshaft assemblies, gear sets, connecting rods, crosshead, and bearings.
Quick Information Brand Name:SaigaoPlace of Origin:China: Description We are Saigao group can do piston and Plunger pump. Such as the following: BW Series Mud Pump BW Series Mud Pumps are mainly used for supplying flushing fluid to the borehole in core, geothermal, water resource, shallow oil, CBM and other drilling process. The fluid can be divided into mud, water, etc. They also can be used as transfer pumps of the above-mentioned medium. This series of mud pumps are with simple structure and easy to maintain and operate. Piston, lip-shaped and self-sealing type, is made of rubber or PTFE and nylon pads, equipped with shock-resistant pressure gauge, necessary spare parts and special tools. Bi-metal liner can be used to extend service life of pump greatly. NBB Series Mud Pump NBB Series Mud pumps are mainly used for the core, coal geology, metallurgy geology, hydrogeology engineering hole drilling fluid is supplied, flushing fluid can be divided into mud, water, etc., may be used as the above medium pump. Structural features The mud pump is crank structure, horizontal triplex single acting piston pump, the piston is self-sealing lip, made of rubber or PTFE and nylon protective pads pressed, the pump adopts auto gearbox, variable five kinds of flow, the pump is compact, high efficiency, durable, safe, reliable, easy maintenance, low maintenance costs. ZB Series Grouting Pump ZB Series grouting pumps are mainly used for kinds of weak corrosivity viscous and nonviscous liquid grouting(such as water, mud), especially for vertical shaft working face grouting, goaf filling, coal mine water inrush governance and so on. The pump is triplex single-acting plunger high pressure pump, fitted with international first-class gearbox, which is of features like compact structure, multistage speed regulation, realizing different flow rate and pressure, meeting the grouting requirements of different formation. Electric motor drives triplex pump through transmission system. It has many advantages, like convenient adjustment for pressure and flow rate, long service life and so on. 3NB & 5NB Series Mud Pump 3NB & 5NB Series Mud Pumps are mainly used for oil, water well, geothermy, CBM, shale gas, coalfield exploration, freezing well as well as well other drilling ,well cementation, work-over and other operations in industrial and mining enterprises. It is used for transferring mud, clay gum, mortar and other medium to the borehole. The pump adopts international advanced technology. It is characterized by advanced structure, reliable operation, good suction performance, long service life of wearing parts, easy for maintenance and repairing and so on. F Series Mud Pump F Series Mud Pumps are mainly used in oil field and geological prospecting for well drilling, well work-over, cementing, water shut off, water flooding and sending mud, clay, grout and so on.
In stock Containers
Description: Lake Petro provide the mud pump accord with API specifications, as per international standard and requirements. Our product offering is extensive used in drilling and fracturing for oil and water well, including: F series, P series, NB series, BW series and TWS series.
The piston rubber in made from specially formulated compounds which are resistant to the effect of heat, oil and water. The multi-ply fabric reinforced backings used in the production of the piston rubbers provide positive, wear resistant seals. This one piece bonded unit provides the same series of advantages, being resistant to oil and other chemical.
Knc piston model of mud pumps: Emsco: f-series fa-series fb-series oilwell: a-series Gardner denver: pah-series tee-series pz-series national: p-series Ideco: t-series qingzhou: 3nb-series.
Oilfiled PZ Series Mud Pump Crosshead Product Description Crosshead Pin The crosshead pin is made from 45# steel. It is the component between connecting rod and crosshead. Our company strictly follows the taper requirements of the encircle according to the precision machining. Crosshead Materials: ductile iron Production Process: It casts by ductile cast iron, which can reach more than 600Mpa tensile strength with good abrasion resistance and long service life. Application: When the pump is in working process, the excircle of the crosshead will move up and down in the slide. In order to ensure good working condition of the pump, our company strictly follows the shape and position tolerances requirements of the excircle and tapered bore. And the crosshead and extension rod is connected with flange bolting. Brand Model Emsco F-350 F-500 F-650 F-800 F-1000 FA-1300 FB-1300 FA-1600 FB-1600 Gardener Denver PZ-7 PZ-8 PZ-9 PZ-10 PZ-11 National 7-P-50 8-P-80 9-P-100 10-P-130 12-P-160 IDECO T-800 T-1000 T-1300 T-1600 Oil Well A-350 A-560 A-650 A-850 A-1100 A-1400 A-1700 China 3NB-350 3NB-500 3NB-800 3NB-1000 3NB-1300 3NB-1600 3NB-2200
Type:f1600 rated input power (hp):1600hp Size:5000*2500*2100mm weight:28t d
Self-priming design (require initial priming to operate) Suitable for waste water transfer, irrigation, garden, mining and civil engineering High quality cast-iron impeller High quality ceramic plunger, silicon carbide water seal Low oil consumption, low noise Powered by advanced YARMAX engine, reliable performance, easy start
Mud Pump Valve Guide Product Description Valve rod guide consists of upper parts and lower parts. Guider (lower) is installed in the inner chamber of the hydraulic cylinder ,for centering and positioning the suction valve body assembly. The guider consists of the guide way and the inner sleeve embedded in the guide way.The material of the guide way is ZG35CrMo, and the inner sleeve is treated by 20CrMnTi carburization and quenching. Brand Model Emsco F-350 F-500 F-650 F-800 F-1000 FA-1300 FB-1300 FA-1600 FB-1600 Gardener Denver PZ-7 PZ-8 PZ-9 PZ-10 PZ-11 National 7-P-50 8-P-80 9-P-100 10-P-130 12-P-160 IDECO T-800 T-1000 T-1300 T-1600 Oil Well A-350 A-560 A-650 A-850 A-1100 A-1400 A-1700 China 3NB-350 3NB-500 3NB-800 3NB-1000 3NB-1300 3NB-1600 3NB-2200
Product name: PN Mud Pump Model: PN Mud Pump Application: can be used for transporting solid-liquid two-phase fluid with mine Product overview Mud pump is a Horizontal single-stage single suction cantilever centrifugal slurry pump, can be used for transporting solid-liquid two-phase fluid with mine. Can also be used in building materials, paper, food, feed and other departments to transport all kinds of slurry. The maximum transmission, concentration of 50-60% (weight) Flow manufacturing using wear-resistant alloy material PN type slurry pump, long life. 6 "and 6" mud sand below the impeller and the shaft is connected with the screw, 8 "and 8" above the mud pump used in key connection. The gap between the blade and sheath and the impeller can be adjusted, to maintain efficient work. 8 "and 8" above the mud pump, the pump body is large, using open structure form level, the disassembly and the maintenance are convenient. Shaft seal packing seal used in general, work to win into higher than operating pressure of 1 kg / square cm shaft seal water. Model PN mud pump, according to the transmission direction, rotates in counterclockwise direction (including 1, 2, 3PN clockwise) Ye Lun with a screw connected with the shaft, if the rotating in opposite directions, Ye Lun will fall off from the shaft, causing the accident. PN Mud Pump
Our plants are specialized in producing wide range of replacement parts for triplex mud pump(such as fluid end module, liner, piston, valve&seats, and a full line of module parts) for brand name mud pumps, including emsco, national, ideco, gardner denver, oillwell, opi wheatly, wilson, wirth, ellis willianms, skytop, brewster etc. All items are manufactured to api 7k quality standards. Module descriptions: Heat-treated and internally hardened for high durability; available in various materials to meet a wide range of applications; standard one or two-piece configuration, with designs available for pressure of 5000psi(35.1mpa), 7500psi(52.7mpa), and 10000psi(70.3mpa); discharge connections available on each side; suction connections on each side or front center. Material is 35crmoa or 40crmonn alloy forged steel. To get better fiber texture, we use electric stove for second forging, or deoxidation treatment. It is forged from three directions and the forging ratio is not less than 4.0:1.0. It can not have crack, impurity, looseness, overburns, etc. And weld is not allowed. It should be confirming to the stipulation of jb/tq252-81, and should be checked by grade3 after quenching the rough module will be rough processed, then the hull hardness is hb285-330.
Here we have all the types of submersible pumps like- 1) dewatering pumps. 2) wastewater pumps. 3) mud pumps. For removing all the wasteage and muds from the industries.
Description: F1600 pump unit is used for transporting high viscosity, large proportion, higher sediment concentration drilling fluid to the well bottom in high pressure, for cooling the bit, wash the bottom, break the rock, and carry out rock cutting when return from the well bottom. It is one the main process equipment of oil drilling operation. F1600 electric pump unit is consist of mud pump, DC motor, small base, big base, belt transmission system, spray system, pressure relief manifold and charging system etc. DC motor is installed on independent skid, and fixed integrally on the big base behind the F1600 pump. Motor power is transmitted to mud pump from input shaft by belt, then drive the mud pump. Small base is equipped with a regulating screw, which can adjust the elasticity of belt. The matching electric spray pump is used to cool hydraulic end piston, cylinder liner, thus to make sure they work properly. API Standard F1600 pump unit meets the requirements of API 7K drilling and wellhead equipment operation specifications and SY/ T5138 standards.
Quick Details: Type:Drilling Mud Pump Product name:eccentric bearing for Bomco F500/800/1000/1300/1600 pump Usage:mud pump Application:oil field Advantage:high quality and competitive price Place of Origin:China (Mainland) Certification:API model:92984QU 928/508QU 929/558.8QU 928/660.4QU 929/660.4QU Outside Diameter:558.8-1060mm Inner diameter:419.1-800mm Supply Ability: Supply Ability:500 Set/Sets per Month Packaging & Delivery: Packaging Details:Standard export packages Port:Shanghai Lead Time :according to your request
Fluid End Expendable Pump Parts 1)Precision machined to API standards 2) Material: Alloy steel&carbon steel Regular package or as consumer's request
Contact Shijiazhuang Ruite Pump Co., Ltd Add:Majuan Village, Nandong Town, Shijiazhuang, Hebei, China (Mainland) Tel:dsales3(at)ruitepump.com Fax:86-0311-89916995 Contact:Hillary Mob:18332439492
Forging is a kind of pressure of forging machinery for metal blank,make its produce plastic deformation in order to obtain certain mechanical properties of shape ,size and forging processing method . By forging can eliminate the metal smelting process of as-cast osteoporosis and so on.
