We export rigging hook, master link, connecting link, lifting goods. from G60 G70 G80. hope receive your inquiry. IRON PALLET, CARTONS OR IRON DRUM
Down The Hole (DTH) drill rig capable of drilling to a depth of 300mtrs (1000 ft) under favorable drilling condition. The drill rig can be operated on rocky formation and hard to medium soil formation. The drill rig can make a hole of diameter 4 to 6.
Trunbuckle, wire rope clip, large dee shackle, thimble etc.
The drilling rigs can fully meet the well-drilling- process requirements by adoption of flexible driving designs- mechanical drives (high-speed diesels, hydraulic transmission box, angle gear box or middle-speed diesel hydraulic transmission, chain combination box), compound transmission and electrical drives (VFD or SCR) etc. * The whole unit is very compact and a quick whole transportation and installation of the whole drilling rig can be realized due to a utilization of a skid-mounted structure. In addition, the drilling rig requires a small working site due to its high integration and compact configuration. * Masts and substructures have various structures, such as: perpendicular-hoist sectional mast, whole-hoist K-type mast, telescopic substructure, spirally hoisted substructure and folding - frame substructure. * A standard and module design and various ways of combination have been adopted in order to boost up the universal and exchangeable performances of the drilling rigs and to meet the user different requirements. * Disc brake or band brake can be applied as main brake and air brake or FDWS brake can be used as auxiliary brake and the energy-consumption braking can be available for electrical-drive-rig auxiliary brake. The drawworks can be equipped with bit-feed motor and control system. * The Internet and communication techniques have been used on the drilling rigs, which can realize an integral display for power, air control, hydraulic control, and monitoring and the intellectual and safe control of the driller. * The perfect configurations of the solid control system, well control system, high-pressure pipe manifold system, the generator house, the engine pump house, doghouse and other auxiliary facilities can meet the user different requirements. Safety and inspection measures are strengthened under the guidance of the design concept of ° Humanism Above All¡± to meet the requirements of HSE.
The series of workover rigs, which the max.Hook load vary from 900kn to 2250 kn, can meet the requirements of workover, service. Equipped with rotary table, swivel and drilling tools, they can perform as a mobile drilling rig up to 1500m depth.We can also supply the complete workover and drilling system assembly including well control, solid control and other relative equipments and service together with the main rig. Export standard package or according to customers' requirments 20-45 days after receiving the copy of l/c or prepayment
Specification as per design ( friede and goldman ).
1.High drill head lifting force; 2.Suit to various drill tools; 3.High hoist lifting force; 4.High drill efficiency; 5.Adaptable to various strata; 6.Rinse medium can use both mud and air. As per customers' requiremnt
Detailed product description HF150E home use water well drilling machine 1, only 2 people handle , portable drilling rig 2, small volum&weight 3, economic Made-in-china , most economic and practical portable drilling rig , hf150e home use water well drilling machine I. Applications This machine mainly apply to farm irrigation, garden irrigation, drinking water well drilling etc, it can drill max 150mm diameter and max 100m depth, it can apply to different stratum, such as sand, soil, clay, hard rock and so on. Ii. Features and advantages Economical. Can be owned by common families. Practical. It gained the patent for its practical capacity. Easy to operate. Two persons can handle it. Portable. Small volum and light weight, easy to move and transport. Salable, its well sold and well received Iii. Main technical parameter Type Hf150e Hight of tower 3m Max. Drilling diameter 150mm Measurement 3000mm*500mm*500mm Max.Drilling depth 100m Total weight 500kgs Engine power 1.3kw Drilling rod length 2m/piece Capacity of hoist 1.5t Diameter of drilling rod 40mm
ESSOS Series is Mud Drilling,DTH Water well Geo thermal drilling Micropiles Soil investigationsGround consolidations. Engine Unit [ Cummins QSB4.5 Tier III] - Aspiration : Turbocharged and Charge Air Cooled - Fuel System : Bosch Electronic - Emission Certifi cation : U.S.EPA Tier3,EU StageIII - Horsepower : 130 BHP [97kW] @ 2,200 RPM - Peak Torque : 459 lb-ft [622Nm] @ 1,500 RPM Mast - Box frame using high strength steel (Tensile 760MPa, Yield 700MPa) - Welding condition AWS D1-1 - V-Profi le power head sliding mechanism - Dual leaf chain with safety wire rope or telescopic cylinder type - Double Clamp(HI-ROKTM) equipped on Mast for angle drilling job - Equipped with 3,000lb winch - Power head stroke 12~14 feet - Power head side shift to give 8� clearance - Mast sliding stroke : 30� - Pull back : 28,000 lb ~ 40,000lb - Pull down : 17,000 lb ~ 28,000lb PowerHead - Two Speed Power Head - Strong and compact helical gears - Separate Water Swivel easy maintenance - Separate Float Cushion Sub - Max Torque : 3,523lbf-ft~5,576lbf-ft - Motor Speed : 20~122rpm - Eaton VIS series Two Speed Motor.
The draw works is driven by two VFD AC motors with 1+1r/2+2r step-less speed, and reversal will be realized by ac motor reversal. The mud pump is driven by VFD AC motors, which are mounted on the rear skid of mud pump, with v-belt transmission and simple structure. The independent driven rotary table runs with 1+1r/2+2r step-less speed, and reversal will be realized by ac motor reversal. Using AC-DC-AC drive technology, rotary table and draw works are four quadrant running and full digital vector control. Single drum, gear driven and one / two shifts smooth speed change draw works is simple in structure and reliable in operation. Feed back / dynamic brake is adopted to replace eddy current brake as auxiliary brake. Automatic drilling is obtained by draw works main motor or an independent motor. Intellectual position control for traveling block prevents crown block and rotary table from collision. Real time communication and network is available by using profibus technology. K type mast is suitable for install top drive system. Sling shot or swing up substructure and mast are applied so that all the equipment can be installed at lower position. Suit for any transportation.
Model : C650D-EXP blasthole drill Specifications: Rated capacity : Nominal hole size 7-7/8(200 mm ) by Rotary method, Upto a depth of 148 (45.12 m) using 30 long 6.25 OD drill pipes. Standard mounting : Tengl, India make Under Carriage model T23/D4 , 24 Triple grouser track 10 6 long with 9 bottom rollers and 2 carrier rollers each side. Independent hydraulic motor with Planetary gearbox drive for each track. Propel speed is 3.0 KMPH on plains and 1.5 KMPH on grades. Gradeability up to 25% grades with Mast down. Pulldown and hoist :Pulldown is achieved through twin hydraulic cylinders and roller chain arrangement. 33 head travel for handling 30 long drill pipe. Pulldown capacity: 35,000 LBS. Hoisting capacity: 20,000 LBS. Standard feed rate: 14 FPM Standard hoist rate: 25 FPM Fast feed rate: 70 FPM Fast hoist rate : 124 FPM MAST : Electrically welded square and rectangular steel mast of robust construction to withstand adverse drilling conditions. Mast is raised and lowered by two hydraulic cylinders with safety check valves. Working height of mast 38 for 30 long drill pipe. ROTARY HEAD : Axial piston hydraulic motor driven top head drive through spur gear reduction with a constant torque of 48,000 Inch-pounds at 0-150 RPM infinitely variable speed. AIR COMPRESSOR: Screw compressor with a capacity of 900 CFM at 100 PSI. Air oil receiver, Oil cooler, Oil filters and safety valves are provided as standard. PRIME MOVER: Cummins India make engine NTA 855C running @ 1800 RPM drives compressor @ flywheel end and hyd. pumps @ front PTO. Fuel tank capacity : 750 lit. DRILL PIPE HANDLING: Hydraulically operated Four pod loader suitable for handling 6.25 OD x 30 long drill Hydraulic power breakout wrench and stem wrench are provided as standard. HYDRAULIC SYSTEM : Open loop hydraulic system for propel, rotation, feed, Fan, auxiliary and pilot circuits. Axial piston ,variable volume pump: 48 US GPM at 4700 PSI for tram circuit and at 4200 PSI for rotation circuit. Axial piston pump : 12 US GPM at 2500 PSI for feed circuit. Gear pump for ROC fan : 22 US GPM at 3000 PSI for ROC fan circuit and 15 US GPM at 2000 PSI for auxiliary circuit. Hydraulic oil reservoir with suction strainers and 10 micron return line filters. Relief valves in all circuits. LEVELLING JACKS : Three hydraulic jacks - one front 140 MM bore, 48 stroke; two rear 125 MM bore, 36 stroke equipped with heavyduty telescopic guide tubes and lock check valves for safety. OPTIONAL EQUIPMENT: Centralised Lubrication system Shock sub for rotary head Rotary Deck Bushing Hyd powered winch Electronic depth counter Automatic Power breakout system Fire detection and suppression system Fast fuelling system Retractable dust curtain Water injection system with water tank.
We supply the good quality oil drilling rig, he brief introduction as follows: Oil drilling rig can be used in exploration and exploitation of oil and gas well.We can supply the :zj20/1350j, zj30/1700j, zj40/2250j and zj40/2250ldb, zj40/2250db and aj40/2250dz, zj50/3150j and zj50/3150ldb, zj50/3150db and zj50/3150dz, aj70/4500ldb and zj70/4500db, etc... Welcome to visit our website. Any question, please feel free to contact us.We will response you promptly. We are there waiting for negotiating with you and quote you our best price.
Xj650 workover rig, with 1470kn of max. Static hook load, is the largest self-propelled workover equipment with single engine, mainly used for medium & deep well workover , oil testing, fishing and pump check operations. It is equipped with a lifting system and a rotary operating system. It is widely applied in many fields. It can be used for lateral drilling and shallow well drilling operation if equipped with a rotary table and relevant parts. Reasonable layout, compact structure, easy transportation, convenient operation and maintenance. 111.55 ft ( 34m ) double section mast, hydraulically raised and telescoped. 12íß8 self-propelled chassis. A hydromatic brake is often used, and eaton water-cooled disc brake or air tong brake is also available. The rotary system is driven by a two-shaft transfer case via a chain of drawworks, or a three-shaft transfer case via a drive line. 5 forward 5 reverse speeds rotary drives equipped with torque release device. Can be used for shallow well drilling operation if equipped with relevant parts. Rod hanger is available. Main parameters Model Xj650 Service depth (2-7/8" ue tubing) ft(m) 27887(8500) Workover depth (2-7/8"dp) ft(m) 22966(7000) (3-1/2"dp) ft(m) 18045(5500) Nominal hook load lb(kn) 303480(1350) Max hook load lb(kn) 330456(1470) Wireline dia/effective line quantity in.(mm) ª)1.13/8(ª)29/8) Max lifting speed of hook ft/s(m/s) 4.30(1.31)
Xj250 workover rig is one of light-duty self-propelled rig, and mainly used for shallow well workover , oil testing, fishing and pump check operations. It is equipped with a lifting system, single drum drawworks, hydraulically raised double or single mast and famous engine and allison hydromechanical transmission. It is easy for transportation and convenient for installation, operation and maintenance. 68.90 ft ( 21m ) double section mastor 59.06 ft ( 18m ) single section mast. 6íß6 full drive chassis, fast movement, good cross-country capability. Double drum drawworks, band brake, without auxiliary brake. Mast base and simple operation platform are hanged on the rear. Rotary driving system can be equipped. Main parameters Model: Xj250 Service depth (2-7/8" ue tubing) ft(m): 10500(3200) Workover depth (2-7/8"dp) ft(m): 8530(2600) Nominal hook load lb(kn): 89920(400) Max hook load lb(kn): 151740(675) Wireline dia/effective line quantity in.(mm): ª)0.87/6(ª)22/6) Max lifting speed of hook ft/s(m/s) 4.6(1.4) Overall dimensions in traveling condition ft(m) 45.01íß8.86íß13.71(13.72íß2.7íß4.18) Weight lb(kg) 61729(29000)
Two (2) sets of diesel engines and allison transmissions. Mature double engine compound box and drive system. 118/125ft(36/38m) mast with stiffened rectangular pipes. 14íß8 reinforced chassis with good cross-country capacity. 5.5/6m foldable substructure and dog house. Top drive system is available. Main parameters Drilling depth(4-1/2"dp) ft(m): 9840(3000) Workover depth(3-1/2"dp) ft(m): 21325(6500) Max.Hook load lb(kn): 381260(1700) Drill line dia., in.(mm)/lines: ª)1-1/8(ª)29)/8 Max.Hook speed ft/s(m/s): 4.46(1.36) Overall dimensions in shipping status ft(m) 69.7íß10.8íß14.67(21.25íß3.3íß4.47) Weight lb(kg) 167548(76000) According to customer's request
1.Zj40/2250db ac drilling rig is suitable for the exploration of petroleum and gas wells with a depth of 2000-3200m by 127mm drilling rod, or a depth of 2500-4000m by 114mm drilling rod. 2.Ac-dc-ac drive system. 3. Single shaft drawwork, drum notch. Hydraulic disc type brake is adopted as the main, while energy-losing brake or etn brake is adopted as the auxiliary. 4.The rotary table adopts independent drive. 5.Parallelogram seat realizes the low-level installation of table-board equipments and derrick, then rises them up by right of drawwork. 6.The main mechanical components of drilling rig follow the standard of api with marks According to customer's request
1.The rig is applicable to 2000-3200m drilling depth for exploring oil well with 127mm drilling pipe, and 2500-4000m drilling depth with 114mm drilling pipe. 2.Utilize diesel engines + torque converters as rig power , has high power and efficiency 3.The rig utilizes integrated chain box which is well-sealed and easy to install 4.Grooved drawwork drum with air clutch to shift speed; Disc brake is applied as main hydraulic and auxiliary brake is eddy current brake. 5.Major components of rig are conform to api specifications and allowed to use api monogram Api
Lifting rigging Features: 1. Material:stainless steel, carbon steel, alloy steel 2. Kinds:our company is a professional manufacturer and exporter in china, we can supply many kinds of lifting rigging, such as shackle, turnbuckle, wire rope clips, hook, snap hook, ring, link, connecting, swivel ring, thimble, bolt and nut, pulley and so on. 3. We also can manufacture according to your drawings and samples. Standard export packaging
Lifting rigging Features: 1. Material:stainless steel, carbon steel, alloy steel 2. Kinds:our company is a professional manufacturer and exporter in china, we can supply many kinds of lifting rigging, such as shackle, turnbuckle, wire rope clips, hook, snap hook, ring, link, connecting, swivel ring, thimble, bolt and nut, pulley and so on. 3. We also can manufacture according to your drawings and samples. Standard export packaging
Drilling rig Our company can supply various offshore drilling rigs, onshore drilling rigs, work-over rigs and their spare parts. The main products include 3000m, 4000m, 5000m and 7000m drilling rigs. All the products are api certified. Please dont hesitate to contact with us would you need any further information.
