Polyester Resin Solution. 55% Solids. Use: Coatings, Inks, Coil Coatings. General Purpose Coatings. Product Code: MP-2000. Manufacturer: Eastman Chemical Co.
WE ARE SUPPLYING FROM INDIA AND FAR EAST
Polyester
We deals in the following products :- 1) PVC Resin 2) Caustic Soda Flakes
Nitrogen - 46% min Moisture - 1% max Biuret - 1% max Prilled - 0.85-2mm Granular - 2-4mm 90-94%min color - Pure White Radiation - Non-Radiactive Free Ammonia - 160pxt ppm max
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Melange 8% Melange 12% Melange 40% Process Ring Spun Technique Single / Doubling / CSY / Melange Blending 100%
Polyester resin solution, polyester resin.
Process Knitting Technique Single Knitting, Double Knitting Function Sportswear, Hijab
Process Knitting Technique Single Knitting Function Bottoms, Underwear, T-shirt
Process Knitting Technique Single Knitting / Double Knitting Function T-Shirt, Sweater, Baby Clothes, Under Garment
Process Knitting Technique Single Knitting Function Baby Clothes, Under Garment, Sweater, Baby Clothes
Process Knitting Technique Single Knitting Function T Shirt, Baby Clothes, Bottoms, Underwear, Jacket
Process Knitting Technique Single Knitting / Double Function T Shirt, Baby Clothes, Bottoms, Underwear, Jacket
Process Woven Machine AJL Quality Printing & Dyeing Type of Width Plain, Twill, Sateen, Oxford, Amunzen, Herringbone, Dobby"
Process Woven Machine Shuttle / AJL Quality Printing / Printing & Dyeing Type of Width Shuttle : Plain AJL : Plain, Twill, Sateen, Oxford, Amunzen, Herringbone, Dobby
Process Woven Machine Shuttle / AJL Quality Printing / Printing & Dyeing Type of Width Shuttle : Plain AJL : Plain, Twill, Sateen, Oxford, Amunzen, Herringbone, Dobby
Crystals Benzoin Siam Crystals
Polyester Viscose Blended Available in Any Blend 65/35 or 50/50 as Per Requirement Waxed for Knitting or Unwaxed for Weaving Single Ring Spun Yarn Available in Melange 10%-40%
We are supplier and exporter of Ferro Silicon. Ferro silicon Specs: Si:75%min. and Si:72%min. C:0.2%max. S:0.02%max. P:0.04%max. Al:2.0%max.1.5%max.and 1.0%max .Commodity: Ferro Silicon Low Al Specs: Si:75%min. C:0.2%max. S:0.02%max. P:0.04%max.Al:0.1%max.0.3%max.and0.5%max. In 1mt plastic woven bags. Ferro Silicon Ferro Silicon has a melting point of 1200�?�°C to 1250�?�°C with a boiling point of 2355�?�°C and Ferro Silicon contains about 2% of calcium and alluminium. Ferro Silicon, as an additive to the production process of ferrous metals, will impart several desirable properties upon the resultant alloy. Some of the primary benefits of adding Ferro Silicon to an alloy is to improve the corrosion resistant properties of the new compound, as well as to add to the high temperature heat- resistance properties of the new alloy, for example, in the production of silicon steel for use in transformer cores.
