Protocol Converter Suppliers and Manufacturers

Contact: amily[at]veecom dot com dot cn GVE-Tplus is an upgrade of GVE-T. It is based on the ASIC circuitry design technology. It is a multi-functional, multi-purpose E1/G.703 to V.35 and LAN three-in-one multiplexer, which is also knowns as the three-in-one interface converter. GVE-Tplus can not only be set up into GVE-T, but also can distribute the whole E1 capacity to V.35 data interface, although E1 must be framed N*64Kbps(N=1--31). The work mode can be either internal clock and slave-clock, or N*64Kbps(N=1--31) external clock to achieve end-linking line. GVE-Tplus can be set up into long-range Ethernet bridge from V.35 to LAN interface. With low cost, it is suitable for use in bridge connection which is sensitive to cost or use in LAN as a stretcher or subsection. It can learn automatically MAC address in the connected LAN and only transmit the aim address to frame in another LAN. There are more than 10000 addresses in its LAN table. And they can be updated automatically. The highest speed of filtrating and transmission is 30000 frame/second(line speed). The buffer size is 64M. The throughput delay is 1 frame. When it is used as a stretcher or subsection, it can forbid filtration so that all traffic can be broadcasted in WAN. 10baseT interface can run in full duplex Ethernet with topology and improve data throughput by eliminating filled blanks in the 64 bytes frames. Without any negotiation in V.35 port, it is specially suitable for use in satellites and other wireless broadcast. 245mm*215mm*50mm

Product Description FE1/V.35 Protocol Converter provide conversion between ITU-T G.703 standard E1 interface and standard V.35/V.24 interface, can convert E1 channel of SDH, PDH, and other Optical Transmission Equipment or microwave, satellite Equipment to V.35/V.24 channel, Extend V.35 channel of DDN. Used widely in data communication networks, Connecting with V.35/V.24 interface of Routers and Optical Transmission Equipments without G.703 interface, realize match between different network equipments, and transparent to upper protocol layer. Technology Characteristics -> Bandwidth range is 64Kbps-2048Kbps Realize data of V.35 transparent transport in the E1 -> Support all kinds of loop function, for testing and opening conveniently -> Support network function, monitor operation condition of facilities -> Support E1 interface of unbalance 75ª+ and balance 120ª+ -> Be possession of testing function of E1 -> Support ITU-T G.703íóG.704 -> HDB3 line coding, comply indication output of route warn -> Coding rate : 2048Kbpsí+50ppm -> 75ª+ physics interface use BNC standard coaxial connector, 120ª+ physics interface use RJ45 connector V.35 Interface: -> Interface Mode : DCE -> Interface Type : DB25 -> Rate : 64Kbps-2048Kbps General characteristics -> Power : 220Ví+20% , -36 ~ -72V -> Power Consumption : < 5W -> Environment Temperature : 0íµ-50íµ -> Size : 220í-165í-35mm -> Net Weight : 900g Packing List -> FE1/V.35 Protocol Converter -> One Power cord (Note : -48v no with power cord) -> Two BNCs Coaxial Connector -> One conversion cable of DB25-M34 -> Manual book

Product Description The E1 to Ethernet protocol Converter is a device that extends Ethernet by means of telecommunication lines (E1 or E1 transport network, such as PDH, SDH, or microwave, etc.) and is also referred to "Net Bridge".It can effectively utilize free bandwidth of telecom operators' lines and can be used instantly once it is deployed, with little increased investment. Technology Characteristics -> Transparent transmission of Ethernet data through E1 lines at 2048Kbps bandwidth -> Plug and play, without any setting or debugging work -> Support automatic negotiation feature in Ethernet and full duplex/half duplex mode -> Support transmission of Jumbo Frames specified in IEEE 802.1Q and Ethernet switches with VLAN capability -> Local data frame filtering -> Provide unbalanced 75ª+ and balanced 120ª+ E1 interfaces E1 Interface: -> Support ITU-T G.703 -> HDB3 line coding, comply indication output of route warn -> Coding rate : 2048Kbpsí+50ppm -> 75ª+ physics interface use BNC standard coaxial connector, 120ª+ physics interface use RJ45 connector Ethernet Interface: -> Fully IEEE 802.3 (2000) compliant -> Bit rate: 10Mbps or 100Mbps -> Interface type: RJ45 General characteristics -> Power : 220Ví+20% , -36 ~ -72V -> Power Consumption : < 5W -> Environment Temperature : 0íµ-50íµ -> Size : 220í-175í-35mm -> Net Weight : 900g Packing List -> V.35/Ethernet Protocol Converter -> One Power cord (Note : -48v no with power cord) -> Two BNCs Coaxial Connector -> Manual book

Industrial Gateway Protocol Converter Fieldbus Modbus to HART Gateway Fieldbus HART to Modbus Gateway

ECAN-401S is a small intelligent protocol conversion product independently developed by Chengdu Ebyte Electronic Technology Co., Ltd. The product uses 8V, 28V wide voltage power supply, integrates 1 CAN-BUS interface, 1 RS485 interface, 1 RS232 interface and 1 RS422 interface, which can realize two-way conversion between CAN and RS485/RS232/RS422 different protocol data. The product supports serial AT command configuration and host computer configuration device parameters and working modes, and supports five data conversion modes including transparent conversion, transparent conversion with logo, protocol conversion, Modbus RTU conversion, and user-defined (user). At the same time, ECAN-401S intelligent protocol converter has the characteristics of small size, easy installation. It has a very high cost performance in the development of CAN-BUS products and data analysis applications. It is an engineering application and project debugging. And reliable assistants for product development.

MODBUS-RTU master station, comply with MODBUS-RTU protocol Electrical interface connected with Modbus device supports TTL level Set MODBUS-RTU slave station via parameters provided by GSD file Company Information Microcybers production center is 1700m2, with anti-static ground, ventilating system, air source transporting system, temperature and humility control system and production devices. The production center consists of 4 workshops and 1 professional lab, they are: production workshop, assembly workshop, ageing workshop, maintenance workshop and product lab. There are professional production line, pressure transmitter assembly line, instrument assembly line, control system module assembly line and product testing line. Microcyber has the batch capacity for 10 thousand devices per year.

G1013 HART to FF Gateway, designed by Microcyber Corporation is a gateway device for HART protocol and FF protocol. As HART master, G1013 HART to FF Gateway communicates with HART slave via HART interface, it can convert dynamic variables in the device to FF device variables output. Product Description Provide FF H1 communication ability to HART device Support standard DD or EDD specification (FF H1) Electrical interface connected with HART device Supports FSK(1200bps) G1013 HART to FF Gateway is 9922.5114.5mm, supporting standard DIN rail installation. G1013 HART to FF Gateway is powered by FF bus, and the HART part shall be with 24V external powered. The recommended is TP cable, and it shall improve devices anti-electromagnetic interference ability.

G1013 HART to FF Gateway, designed by Microcyber Corporation is a gateway device for HART protocol and FF protocol. As HART master, G1013 HART to FF Gateway communicates with HART slave via HART interface, it can convert dynamic variables in the device to FF device variables output. Product Description Provide FF H1 communication ability to HART device Support standard DD or EDD specification (FF H1) Electrical interface connected with HART device Supports FSK(1200bps) G1013 HART to FF Gateway is 99Ã?22.5Ã?114.5mm, supporting standard DIN rail installation. G1013 HART to FF Gateway is powered by FF bus, and the HART part shall be with 24V external powered. The recommended is TP cable, and it shall improve devices anti-electromagnetic interference ability.

Physical Parameters Bus signal: compliant with IEC61158-2 physical layer standard Bus power supply: 9 ~ 32V Operating temperature: -40 ~ 85°C Static current: â?¤14mA Humidity range: 5% ~ 95%,non-dew Mechanism size: diameter 66mm(can be customized) Supportive MODBUS Communication Parameters Address: 1 ~ 255 Baud rate: 9600 / 19200 / 15625 / 31250 /62500 / 125000 bps Data bit: 7 / 8 bits Calibration: odd / even calibration Stop bit: 1 / 2 bits CRC calibration: low byte ahead / high byte ahead Data format: support various data formats Supportive MODBUS Function Code Function Code 1: read loop status Function Code 2: read discrete input status Function Code 3: read keeping register value Function Code 4: read input register value Function Code 6: write loop Function Code 16:write multiple register values

Global Tech GFP EoP, Ethernet over PDH, Interface Converter can transport GFP encapsulated Ethernet service over 1 up to 16 E1 channels. Fully comply with G.7041, G.7042, G.7043, and G.8040 recommendations, GFP Interface Converter can cooperate with the products from other manufactures adopted the same recommendations. GFP Interface Converters can transform traffic between E1 interface and Ethernet interface, and utilize current adequate E1 resources to extend the Ethernet transmission distance and coverage range without any network reformation. Feature * GFP encapsulation based Ethernet interface can cooperate with other vendors GFP based Ethernet equipments. * Up to 4 Ethernet interfaces. * Switching Ethernet interfaces isolation is configured by E1 channel or 802.1Q through NMS, disabled by default. * Automatically Fault Shifting function. * Support Telnet/Web browser/SNMP NMS management. Strong NMS function to support client managing in complicate topology. Technical Parameter * E1 Interface - Bit Rate: 1.984M bps - Coding: HDB3 - Impedance: 75, Unbalanced/ 120, Balanced - Port Feature: G.703 and G.704 - Connector: Q9 (75)/ RJ45 or RJ48-C (120) * Ethernet Interface - 10M/100M auto negotiation - Full/half duplex auto negotiation - Port Quantity: 1, up to 4 ports - MDI/MDIX auto negotiation - Related Standard: G.7041, G.7042, G.7043, G.8040 * Optical Interface - Wavelength: 850nm, 1310nm, 1550nm - Optical Port: Single Fiber/ Dual Fiber, FC/SC, Transmission Distance, SMF/ MMF optional. - Tx Power: > -8dBm, 40km - Rx Sensitivity: < -36dBm, 40km * Operation Environment - Working Temperature: -10~ 55 - Storage Temperature: -40~ 70 - Relative Humidity: 5%~ 95%, non-condensing - No corrosive and solvent gas, no dust and heavy EMI - Power Supply: AC 180~ 260V, Desktop, DC -72~ -36V, Chassis - Support 1+1 dual power supply in chassis configuration - Typical Consumption: 5W, Desktop 75W, Chassis - Physical Dimension: Desktop, 19¡± Rack-mountable: 218mm(W)*44mm(H)*136mm(D) Chassis: 483mm(W)*171mm(H)*177mm(D).

Interface converter Introduction: Ne2701bridge (also called 2mbps g.703 / ethernet interface converter) serves as a type of data communication equipment to transparently and directly convert the transmit data from 2m g.703 interface into ethernet. It is ideal for the case where low-cost bridging is required. It also can be used as a lan extension. When used as extension or segment switch, it has two working status, namely filtering and non-filtering, to determine whether all communication traffic is allowed to transport to wan circuit or not. Main features: (1 e1interface (1 utp interface, for connection to network card or hub (optional clock: internal clock (master mode); receiving and recovering clock (complete alert and status display 210mm140mm38mm

The fieldserver is one of the most powerful and flexible industrial protocol translator currently in the market today. A protocol translator with over a 120 protocol supported, an ethernet gateway, a port expander, a scanner and a tunneling devices its no wonder that this product is becoming the standard.

QuickServer can configure a combination of drivers such as Modbus RTU, Modbus TCP, BACnet/IP, BACnet MS/TP, LonWorks, JCI Metasys N2 and SNMP. There are two QuickServer designs. 1) FS-QS-1010-XXXX: two serial ports and one Ethernet port. 2) FS-QS-1011-XXXX: one serial port, one Ethernet port and one FTT-10 LonWorks port. Key Features: * Multi-configuration capability; specific configurations selectable via DIP switches or software. * Ability to interface up to 250 points of common BAS protocols. * Same firmware as our industry proven devices. * Free BACnet Explorer worth $595 with purchase that include a BACnet driver.

Protocol converter, temperature transmitter, pressure transmitter.

Media converter PDH multiplexer transceiver CWDM protocol converter.