Interface Converter

Overview: GVE-Tplus is E1 to V.35/V.24/RS232 and Ethernet Converter. Other series interface RS449/RS530/X.21 also can be optional. E1 port can support BNC/75ohm and RJ45/120ohm optional. This device provides an economical digital access solution for E1 and fractional E1 network services. With a adapter cable, the device can connect to other DTE device, such as router, at data rates of 64Kbps to 2048Kbps.User data is placed into the E1 frame, using only the required number of timeslots, timeslot assignment is accomplished according to the data port speed and manual setting of DIP switches. The V.35 or V.24/RS232 and Ethernet share the 2Mbps bandwidth, the total bandwidth of the 2 interfaces must be not more than 1984Kbps.GVE-Tplus is widely used in communication network, both in WAN and LAN connection field. Features: *Comply with ITU V.35, G.703, G.704, G.706, G.823 *Full comply with IEEE 802.3 /IEEE 802.1Q (VLAN) *Framed (N*64Kbps) and unframed (2.048Mbps) optional *Ethernet port 10Mbps, Full/Half Duplex mode compatible *Frame mode support PCM30/PCM31 *Support CRC4 *Support internal clock, E1 recovery clock or V.35 line clock *Provide analog and digital loopback and remote digital loopback test *For E1 interface, 75ohm (unbalanced) and 120ohm (balanced) optional *For data interface, V.35 and V.24/RS232 optional *Comprehensive LED indicators on front panel, convenient for the diagnosis of equipment working state *Stand-Alone and Rack-Mount available *16-slots, elaborate cooling design and two redundant power supplies *Support management *-48V DC & 220V AC power supply optional Specifications: E1 & FE1 interface Comply with ITU G.703,G.704,G.706,G.823 Rate:2.048Mbps;N*64Kbps(N=1~31) Code type:HDB3 Impedance:75ohm unbalanced & 120ohm balanced optional Physical interface:BNC coaxical for unbalanced RJ45 twisted pair for balanced Ethernet interface Comply with IEEE 802.3/IEEE 802.3Q(VLAN) Rate:10Mbps,Half/Full auto-negotiation MDI/MDI-X optional Physical interface:10 Base-T(UTP);RJ45 V.35,V.24/RS232 interface Comply with V.35,V.24/RS232 standard Rate:2048Kbps;N*64Kbps(N=1~31) Transmission mode:Synchronization Data interface:V.35 or V.24/RS232 Physical interface:DB25 female jack,V.35 via external adapter Work mode:DCE Power supply AC power:220V¡¨¤10%,50Hz DC power:-48V(optional) Power:5W Environment Temperature:0¡«40¡æ Humidity:0¡«95% RH Carton.

Overview E3/t3-t is state of the art network termination units (ntu) connecting fast ethernet lans over e3 or t3 circuits. The devices enable service providers and isps to supply transparent. Ethernet services to remote locations over existing e3/t3 infrastructure. The devices can be used in a point-to-point application and widely used in lnteroffice or enterprise lan connection. E3/t3-t has one unframed e3 or one framed t3 port, and one 10/100basetx port. Packets are forwarded from the ethernet network to the e3 or t3 network at wire-speed, fully utilizing the expensive tdm circuit bandwidth. Features: * best price performance ethernet over e3 or t3 intelligent converter in the market * wire-speed forwarding fully utilizing the e3 or t3 circuit * vlan stacking and tagging enabling service providers to provide layer 2 transparent lan services while securing providers management * fault propagation of e3 or t3 error conditions to ethernet port * diagnostic collection on tdm and ethernet interfaces * comprehensive led indicators on front panel, convenient for the diagnosis of equipment working state * -48v dc & 220v ac power supply optional. Specifications E3 interface Comply with itu g.703 Rate: 34.368 mbps Code type: hdb3 Impedance: 75ohm unbalanced l Physical connector: bnc coaxial for unbalanced T3 interface Comply with gr-499-core, ansi t1.107, ansi t1.102 Rate: 44.736 mbps Code type: b3zs Impedance: 75ohm unbalanced l Physical connector: bnc coaxial for unbalanced Power supply Ac power: 220v+-10%, 50hz Dc power: - 48 v (optional) Power: 5w Environment Temperature: 0-40oc Humidity: 0-95% rh Carton.

Overview: Dhodt-eoc is a converter for stm-1 converter electrical and optical interface conversion. It is designed for the pdh equipment coaxial interface and optical interface interconnect. Dhodt-eoc is an interface converter for stm-1 electrical and optical interface conversion.It is designed for the sdh equipment coaxial interface and optical interface interconnect, as well as the atm 155.520 mbps interface and sdh device interconnection. Complete loopback facility is supported for system diagnostic and commissioning.Compact casing and simple operation achieve the cost saving and investment protected. Features: 1. High reliability, comply with itu-t g.703 and g.957 2. Single fiber bi-directional is selectable 3. State-of-the-art design, ensure normal working under different environment. 4. Supports local and remote loop-back on electrical or optical interface for system diagnostic. 5. Suitable for sdh and atm 155.52 mbps interface interconnection. 6. Simple operation and maintenance 7. Compact design and low power consumption. Specifications: Electrical interface Standard:itu-t g.703 compliant Data rate:155.52 mbps Line code:cmi Physical connector:bnc coaxial Optical interface Standard:itu-t g.957 stm-1 Bit rate:155.520 mbps Coding:nrz Connector:sc Light source:laser diode Wave length:1310nm (typical), or 1550nm (optional) or single Fiber bi-directional (optional) Transmit power:-12dbm (1310nm) / -5dbm (1550nm) Receive sensitive:-36dbm (1310nm) / -38dbm (1550nm) Power supply Ac 220v10%, 50hz Dc¡¡ìc48v (optional) Consumption:5w Environment Temperature:050 Humidity: 90% (non condensing) Dimension Wd(mm): 245 x 215 x50 Carton.

Gve-tplus(e1/g.703 to v.35 ehernet converter GVE-Tplus(E1/G.703 to V.35 Ehernet converter Detaile Selling Lead Description Features: 1) GVE-T plus can convert E1 to both V.35 interface and LAN interface 2) Bandwidth of every port can be set into N x 64kbps (N=1-31) continuous data stream, although the total bandwidth of the two ports must be no more than 31 and must be inserted into PCM time slot of E1. It supports choices of CRC4 on/off and CAS/CCS (30 & 31 time slot) 3) GVE-T plus also can distribute the whole E1 capacity to V.35 data interface, although E1 must be framed N x 64kbps (N=1-31). The work mode can be either internal clock and slave-clock, or N x 64kbps (N=1-31) external clock to achieve end- linking line 4) GVE-T plus can be set up into long-range Ethernet Bridge from V.35 to LAN interface 5) GVE-T plus has two transmission modes to choose from: data and image 6) GVE-T plus has local and remote loop backs. Therefore user can use circuitry-test and malfunction diagnosis conveniently to perform port-to-port integrity test Detailed Product Description Ethernet features: 1) LAN table: 10,000 automatic learning and updating 2) Filtering and forwarding: 30,000 frames / second 3) Buffer size: 64M 4) Throughput delay: 1 frame 5) VLAN: comply with 802.1Q LAN feature: 1) Standard: conforms to IEE802.3 / Ethernet 2) Work mode: full duplex / half duplex 3) Data rate: 10Mbps 4) Physical interface: 10 BaseT (UTP), shielded RJ-45 5) WAN E1 / G.703 feature: 6) Line transmission rate: N 64Kbps (N=1-31) 2048Kbps 7) Line coding options: HDB3 8) Format of line frame: G.703 (framed / unframed) 9) Line interface: BNC; RJ45 Transmission features: 1) Comply with G.703 2) Rate of data transmission: N 64Kbps (N=1-31) 3) Transmission mode: synchronization 4) Data interface: V.35 or V.24 / RS232C DCE 5) Clock: master clock; slave clock; external clock 6) Testing methods: local analogy loopback test; remote digital loopback test Feature: 1) Power supply: 220VACf+10%, 50Hz 48V DC (optional) 2) Power consumption: 5W 3) Volume: 225 x 145 x 40mm; 9" (L) x 5.8" (W) x 1.6" (H) 4) Temperature: 0 - 40fpC

Supplier: Pcm30, pdh, interface converters, power distribution, scada_rtu, fiber optic multiplexer+pcm, sdh, distribution frame, transmission power, antenna

Supplier: Interface converters, data communication converters, networking devices, digital remote I/ O, serial over ethernet, USB to serial, serial over fiber, bluetooth, devices, repeater

Supplier: Industrial switches,managed switch,poe switch, interface converters, serial servers, industrial wireless routers, industrial wireless data transmission terminals , optical fiber communication products and so on
Services:

Contact: amily[at]veecom dot com dot cn GVE-Tplus is an upgrade of GVE-T. It is based on the ASIC circuitry design technology. It is a multi-functional, multi-purpose E1/G.703 to V.35 and LAN three-in-one multiplexer, which is also knowns as the three-in-one interface converter. GVE-Tplus can not only be set up into GVE-T, but also can distribute the whole E1 capacity to V.35 data interface, although E1 must be framed N*64Kbps(N=1--31). The work mode can be either internal clock and slave-clock, or N*64Kbps(N=1--31) external clock to achieve end-linking line. GVE-Tplus can be set up into long-range Ethernet bridge from V.35 to LAN interface. With low cost, it is suitable for use in bridge connection which is sensitive to cost or use in LAN as a stretcher or subsection. It can learn automatically MAC address in the connected LAN and only transmit the aim address to frame in another LAN. There are more than 10000 addresses in its LAN table. And they can be updated automatically. The highest speed of filtrating and transmission is 30000 frame/second(line speed). The buffer size is 64M. The throughput delay is 1 frame. When it is used as a stretcher or subsection, it can forbid filtration so that all traffic can be broadcasted in WAN. 10baseT interface can run in full duplex Ethernet with topology and improve data throughput by eliminating filled blanks in the 64 bytes frames. Without any negotiation in V.35 port, it is specially suitable for use in satellites and other wireless broadcast. 245mm*215mm*50mm

Supplier: Industrial interface converter, USB, RS-232, RS-485, RS-422, TCP/IP communication transmission conversion