Preformed Tension Clamp Suppliers and Manufacturers

ADSS Preformed Short Span Tension Clamp Preformed Tension Clamp are designed to hold conductors and strands evenly to prevent conductor deformation. This product is designed for bare and stranded conductors and is recommended for use with plastic sheathed conductors. At the same time, the tension clamp can withstand at least 95% of the rated breaking strength of conductors and strands, and is made of high-strength materials. Composition: twisted wire, rubber insert, cast aluminum shell, right-angle shackle, U-shackle. Purposes: supporting cableï¼?make the ADSS hang on the tower. Structure and Materials Shackle - Constructed from hot-dip galvanized steel, the shackle is linked to the reinforcing bar unit. Twisted Chain Ring - Made of hot-dip galvanized steel, the twisted links serve to connect the shackle to the thimble. Sleeve - Composed of hot-dip galvanized cast steel, the sleeve is inserted into the unclamp of the tension clamp to ensure protection and facilitate connection. Armored Rod - Fabricated from aluminum-clad steel wire, armored rods enhance friction through a layer of granular emery within the cable. These rods are pre-assembled into four subsets to reduce misalignment errors and expedite installation. The ends are bent outward to provide strain relief in critical areas where the cable departs. Prefabricated Dead Ends - These components are constructed from either hot-dip galvanized steel wire or aluminum-clad steel wire and are assembled in the shop into a subset featuring a solid layer of emery. This design increases the grip of the tensioning clamps while minimizing lateral pressure.

OPGW Preformed Double Tension Clamp Preformed tension clamps are also named preformed dead-end or dead-end cable clamps for communication ADSS fiber, OPGW cable or OPPC. A preformed dead end is a tension wire that has an important role in ADSS/OPGW transmission lines. Dead-end cable clamps are designed to connect ADSS/OPGW/OPPC to overhead towers or poles. Preformed Tension Clamp Preformed tension clamps are also named preformed dead-end or dead-end cable clamps for communication ADSS fiber, OPGW cable or OPPC. A preformed dead end is a tension wire that has an important role in ADSS/OPGW transmission lines. Dead-end cable clamps are designed to connect ADSS/OPGW/OPPC to overhead towers or poles. The unique pre-formed tension clamp design not only simplifies installation, but also ensures a secure cable connection. Dead-end cable clamps provide superior performance to protect ADSS/OPGW/OPPC cables from stress point damage and prevent signal degradation during transmission. Pre-formed tension clamps for conductors and grounds are similar in appearance to pulling dead-end clamps, but the specifications, raw materials and strength requirements of the two types of pulling clamps do differ significantly. Although there are different design standards in different countries, we can OEM to customer requirements. As an experienced manufacturer and supplier of preformed tension clamps, Seinei understands the standards, the manufacturing process and understands your needs. If you have any questions, please feel free to contact us.

Preformed tension clamp is also called preformed dead end or dead end cable clamp. The raw material of preformed tension clamp is aluminum clad steel wire or galvanized steel wire, For communication ADSS optical fiber, OPGW cable and OPPC. The unique pre-formed tension clamp design not only simplifies the installation but also ensures the safety of the cable connection. Terminal cable clamps provide excellent performance to protect ADSS/OPGW/OPPC cables from stress points and prevent signal drops during transmission. What is the raw material of the pre-formed tension clamp The raw material of the prefabricated tension clamp is aluminum-clad steel wire or galvanized steel wire. What is the purpose of prefabricated tension clamps Prefabricated tension clamps are designed to connect ADSS/OPGW/OPPC to overhead towers or poles. What are the types of prefabricated tension clamps The preformed tension clamp and guy wire dead end grips used on the conductor and earth wire look alike in shape, but there are really big differences in the specification, raw material, and strength requirement of the two types of guy grips. 1. Dead-end for short span ADSS Dead-end for short span ADSS with a small tension clamp material for aluminum-clad gang wire, mainly used for the corner towers, the middle of follow-tower and connecting the terminal tower, the largest installation file from the less than 100 meters. 2. Dead-end for medium/long span ADSS Dead-end for medium span ADSS in tension and large tension clamp material for aluminum-clad steel wire, mainly used for files larger than 100 meters away from the corner tower, the middle tower and Terminal Tower successive connection. As an experienced manufacturer and supplier of preformed tension clamps, Boersen Photoelectric is able to OEM to customer specifications. If you have any questions, please feel free to contact us.

Description ADSS preformed tension clamp is designed for connecting and fastening the ADSS fiber to the overhead pole. Feature 1) quick and easy installation 2) distribute the stress uniformity 3) guarantee no cable damage or slipping 4) strong resistance to corrosion and cruel environment 5) made of aluminum alloy, aluminum clad steel and galvanized steel Order Tips 1- confirm the cable type 2- confirm the cable diameter 3- confirm the span and the rated tensile strength 4- the material can be aluminum alloy, aluminum clad steel or galvanized steel Our service 1, Fast Response Time 2, Quality and Certified Products3, Resonable Price 4, Cheap and Reliable Transportation 5, 7*24 Hours After Sales Service

ADSS Preformed Short Span Tension Clamp Tension clamps are designed to hold conductors and strands evenly to prevent conductor deformation. This product is designed for bare and stranded conductors and is recommended for use with plastic sheathed conductors. Preformed Tension Clamp ADSS tension clamps are designed to hold conductors and strands evenly to prevent conductor deformation. This product is designed for bare and stranded conductors and is recommended for use with plastic sheathed conductors. At the same time, the tension clamp can withstand at least 95% of the rated breaking strength of conductors and strands, and is made of high-strength materials. Composition: twisted wire, rubber insert, cast aluminum shell, right-angle shackle, U-shackle. Purposes: supporting cableï¼?make the ADSS hang on the tower. Features: 1. Component: preformed wire, rubber inserting, casting aluminum shell, right angle shackle, U shackle etc. 2. Usage: supporting,make ADSS cable hang on the pole and tower. 3. Features: a, stress on average, no concentration stress, protect cable better and increase the stiffness of cable in the mount point. b, good dynamic stress. It can provide enough grip strength(10%RTS) c, rubber inserting make abrasion low. d. excellent aluminum alloy improve the mechanical and resist-corrosion function, extend life. Technical requirements: meet the DL / T 766-2003 ADSS with the preformed helical fittings technical requirements and test methods..

OPGW the Preformed Helical Tension Clamp The OPGW Premored/Helical Tension Clamp is primarily used to install cables with RTS less than 160 kN to tension towers/poles, corner towers/poles and terminal towers/poles. A complete set of OPGW prefabricated/spiral tensioners includes aluminum alloy or aluminum clad steel dead ends, structural reinforcement rods, support fittings and grounding clamps, etc. Wire Tension Clamp An OPGW (Optical Ground Wire) wire tension clamp is a specialized device used in the installation and maintenance of OPGW cables. OPGW cables are composite overhead cables that combine optical fibers for communication purposes with a metallic ground wire for power transmission and grounding. The OPGW wire tension clamp serves the purpose of securely attaching the OPGW cable to the supporting structure, such as poles or towers, while maintaining the necessary tension. It plays a crucial role in ensuring the stability and reliable performance of the OPGW system.

ADSS Preformed Short Span Tension Clamp Tension clamps are designed to hold conductors and strands evenly to prevent conductor deformation. This product is designed for bare and stranded conductors and is recommended for use with plastic sheathed conductors. China ADSS Tension Clamp ADSS tension clamps are designed to hold conductors and strands evenly to prevent conductor deformation. This product is designed for bare and stranded conductors and is recommended for use with plastic sheathed conductors. At the same time, the tension clamp can withstand at least 95% of the rated breaking strength of conductors and strands, and is made of high-strength materials. Composition: twisted wire, rubber insert, cast aluminum shell, right-angle shackle, U-shackle. Purposes: supporting cableï¼?make the ADSS hang on the tower. Features: 1. Component: preformed wire, rubber inserting, casting aluminum shell, right angle shackle, U shackle etc. 2. Usage: supporting,make ADSS cable hang on the pole and tower. 3. Features: a, stress on average, no concentration stress, protect cable better and increase the stiffness of cable in the mount point. b, good dynamic stress. It can provide enough grip strength(10%RTS) c, rubber inserting make abrasion low. d. excellent aluminum alloy improve the mechanical and resist-corrosion function, extend life. Technical requirements: meet the DL / T 766-2003 ADSS with the preformed helical fittings technical requirements and test methods..

Great for earring, . Also shop for jewelry & accessories at best prices . best quality and finishing

Preformed dead end grip, preformed tension clamp, preformed strain clamp, preformed tension clamp and armor rods forming machines, adss and opgw preformed fittings, overhead line hardware, transmission line hardware fittings..Manufacture and exporter

ADSS with The DN Short-span Tension Clamp ADSS (All-Dielectric Self-Supporting) tension clamp is a device used to attach and support ADSS cables to poles or towers in overhead fiber optic cable installations. It is designed to grip the cable without damaging it while also providing the necessary tension to keep the cable taut and secure. Tension Clamp ADSS (All-Dielectric Self-Supporting) tension clamp is a device used to attach and support ADSS cables to poles or towers in overhead fiber optic cable installations. It is designed to grip the cable without damaging it while also providing the necessary tension to keep the cable taut and secure. The ADSS tension clamp is typically made of corrosion-resistant materials such as aluminum or plastic and is available in different sizes to fit various cable diameters. Composition: twisted wire, thimble, PH-type shackle, U-type shackle etc. Purposes: support all strain, make ADSS cable connect the strain pole and tower. Features: Preformed wire connect the pole and tower by thimbles etc. link fitting, afford the load of the transmission line. Grip strength not less than cable 95%RTS in case that not more than lateral pressure of the cable E xcellent aluminum clad steel improve the mechanical and resist-corrosion function, extend life. Corrosion-resistant materials such as aluminum or plastic to ensure durability and longevity. Gripping mechanism that securely holds the cable without causing damage. Tensioning mechanism that allows for adjustment of the cable tension. Insulating material to protect the cable from electrical currents. Suitable for use with a range of cable diameters. Easy installation and maintenance. Technical requirements: meet the DL / T 766-2003 ADSS with the preformed helical fittings technical requirements and test methods