Main technical parameter Gas utilized: natural gas, oil, water gas Material: base rack, chain rack and chain runway adopted 12# standard channel steel. Furnace frame adopted 40*60 square pipes. Base plate adopted 3mm hot plate. side plate adopted 2mm cold plate. Fireproof and heat preservation material: bottom brick is adopted with light soaking brick; surface brick and furnace hearth are adopted with aluminum fireproof brick; soaking cotton is adopted with fiber silicon cotton.
The die furnace heat the die by heating wire and through circulation fan to maintain temperature uniformity , so fastest heating and temperature uniformity available. Besides, the furnace has the characteristics of good sealing performance, durable and easy operation. Main technical parameter Heating type: electricity type Chamber temperature tolerance.
Suitable for small or middle-sized extrusion press. It depends mainly on the friction of belt and pulley for the deliver of aluminum profile. It can especially avoid the profile to be secondary bumps & scratches &scraped & distorted. With the characteristics of advanced technology, rational structure, beautiful appearance, steady, easy operation, is quiet in working.
Wind turbine, extrusion die, shaft, flange, extrusion die, multi-billet hot shear furnace, puller, die oven, aging oven.
Horizontal single movement aluminum extrusion press Model: horizontal, four tie rods, hydraulic system, plc for electric power, semi-automatic control, easily operated, automatic holding die slide and automatic charging into container. Features: this extrusion press is equipped with variable piston pump which can automatically control the output of pump according to the change of pressure. Electric power consumption is low and oil temperature does not easily rise up. Speed control is also available. Thus, it can have best operating efficiency.
Horizontal axis wind turbine technical parameter 2000w Performance Rotor diameter 3.2m noise test report Blades quantity 3 pcs wind speed(m/s) noise(db) Direction always downwind 3 24.6 Blades material glass fiber 4 24.8 Rated output 2000w 5 29.5 Maximum output 2500w 6 35.2 Initial voltage 96v 7 40.7 Initial wind speed(m/s) 3m/s 8 48.2 Nominal wind speed(m/s) 9m/s 9 52.6 Stormstand up to 35m/s 10 61.8 Wind protection autofurl 11 65.8 Rotor speed 280 r/min 12 70.5 Wind turbine type pmg (on constant magnets) remark 1.Noise report (tested by hand held sound level meter) 2.Test position at 12m away from generator (average value of 3 point-rear, left, right). 3.The noise value includes wind noise. Working temperature from -40 to +60 c Total capacity(one year) 5000kwh Charge control automatic intelligent control Recommended battery 12v150ah 8pc Batteries full charged about 10 hours Weight(kg) 55kgs (without tower) Packing detail Packing name quatity weight(kg) packing size(mm) packing Generator 1 54.5 660*415*400 plywood box Controller+ inverter (dc96v, ac220v) 1 44.5 650*480*490 plywood box Tower 1 93 3100*320*320 nude Fittings 1 58 660*450*240 plywood box Blades 1 33.5 1640*220*290 plywood box Total 283.5kg 0.76cbm.
Steel billets result from the second stage of the steel production process. They are hot-rolled or forged from an ingot or strand cast. steel billets from 45 x 45 mm to 150x150 mm, and round steel billets from 120 mm to 270 mm in diameter. Length : Specifiable up to 12 m Quality : In various internationally well known standards including afnor (nf), aisi, astm, bs, din, euronorm, gost, jis, iso, sae, si, ts, uni, etc. (eg. Astm a 615 gr 40 or 60, bst 420 s, din 488, st 37.2 din 17100, nfa 35015 and 16, bs 4449 (gr 250 or 460), jis g 3112 (sd 30, 35, 40), si 739 s 400, si 739 s 400 w, feb 44 k, 3 sp/ps or 5 sp/ps gost 380 88, 35 gs or 25 g2s, gost 5781-82, etc) Other grades available according to customer's request
Mill scale, is formed on the outer surfaces of plates, sheets or profiles when they are being produced by rolling hot iron or steel billets in rolling or steel mills. It looks like a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in color. Being produced during the reheating, conditioning and hot rolling operation for the production of steel articles, the mill scale initially adheres to the steel surface and protects it from atmospheric corrosion, provided no break occurs in this coating. From the chemical and physical analysis performed on the scrap, and according to the european environmental rules, the material has been classified as a special non dangerous waste, listed in green list In particular the mill scale can be classified as follows: Einecs (european commission no.): 266-007-8 Waste code: 10 02 10 Basel code: b 12 30 Hs code: 2619.00
We are glad to propose 500 MT of stain less steel mill scale. Mill scale is formed on the outer surfaces during by the hot rolling lamination of stainless-steel products. At a visual inspection the material is a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in colour, but it also contains considerable alloying elements such as chromium and nickel. The recovery ratio after melting in furnace for the most valuable alloy elements is: - Ni: 3.5 - 4.5% - Cr: 6-8% From the chemical and physical analysis performed on the scrap, and according to the European environmental rules, the material has been classified as a special non dangerous waste, listed in green list. In particular the mill scale can be classified as follows: Waste code: 10 02 10 The material is stored on cemented flooring, and it can be loaded loose in tipper trucks or containers. Chemical analysis of the material is available on request.
Refractory bricks, high alumina bricks, acid proof bricks, tiles and castables, all mortars and fire clay, low cement castables, insulating castables, conventional dense refractory bricks, insulation bricks, cold face, hot face insulation bricks, hot face insulation bricks, acid resistant bricks/components, membranes, acid resistant cement, construction chemicals, class 1 ar tiles and bricks 38mm and 75mm, 4457 vitrified ar tiles with 0% water absorption, 20mm & 25m, primer, mastics, pot. silicate cement, coerce cement, furnace based cement, crushed refractory boiler bed material, acid resistant tiles, acid resistant brick fireclay type, acid resistant brick red shale type, bitumen primer, epoxy resin & hardner, furan powder and syrup solution,.
Heating aluminum billet Billet diameter: 70~500mm Billet length:3~10m Temperature: 420~580 degrees Energy:natural gas, lpg, diesel oil Design type: single log type and multi log type Standard packing for ship
Features Of Steel Billets Steel billets result from the second stage of the steel production process. They are hot-rolled or forged from an ingot or strand cast. Smaller and longer than a bloom, billets are usually a square cross-section less than 36 square inches. They are used for the manufacture of all ‘long’ steel products such as bars, rods, pipes, tubes, wire and wire products.
Application: heating aluminum billet , shearing billet Features: auto billet loading , auto billet feeding , auto billet transferring , auto heating , auto length sized , auto sheat , auto billet moving , heat recovery. Advantage: non-oil leakage , low energy consumption , shear smoothly , precision shear length , hing configuration , long use life , high production , low fault . Parameters : Extruding machine : 450t~2000t Billet diameter : f70~f460mm Billet length: 2m~5m Shear length: 250mm~1500mm Shear tolerance: ±1mm Temperature difference: ±5?
Hr coils, hr sheets, hrpo, hot rolled coils, hr plates cold rolled coils, cr coils, cr sheets, galvanized coils, gi coils, galvalume coils, ga roofing sheets, corrugated roofing sheets, Galvannealed coils, color coated coils, ppgi, ppgl profile sheets, color coated profile roofing sheets, tmt rebars, tmt debars, c and z purlin, conduit pipe, gi conduit pipe, ms conduit pipe stainless steel coils, stainless steel sheets, ms slabs stainless steel plates, steel deck sheets, billets, angles, channels, beams, erw pipe, hollow sections, structural steel, steel wires, stainless steel pipes, iron ore, pig iron, sponge iron, ferroy alloys, iron ore pellets, high tensile galvanized coils, checkered plates, checkered coils, aluminum coils, aluminum sheets, blooms, ingot, wire rod, electrical steel, crno, crgo, rice, pulses, spices, food grains, engineering machines.
Used rails r50 65, hms 1/2, jet fuel, crude oil, en590, copper millberry, copper cathode, copper powder, aluminum ingots, zinc ingots, sugar, hot & cold rolled coil, whit spirit, urea. lumber, rebar steel, billet steel, metal products including bronze, brass, aluminum bronze, green metal bars, shapes, rods & ingots.International commodities traders & resellers
A billet is a length of metal that has a round or square cross-section, with an area less than 36 in2 (230 cm2). Billets are created directly via continuous casting or extrusion or indirectly via hot rolling an ingot or bloom. Billets are further processed via profile rolling and drawing. Final products include bar stock and wire. Centrifugal casting is also used to produce short circular tubes as billets, usually to achieve a precise metallurgical structure. They are commonly used as cylinder sleeves where the inner and outer diameters are ground and machined to length. Because their size is not modified significantly, they are not always classified as semi-finished casting products.
A billet is a length of metal that has a round or square cross-section, with an area less than 36 in2 (230 cm2). Billets are created directly via continuous casting or extrusion or indirectly via hot rolling an ingot or bloom. Billets are further processed via profile rolling and drawing. Final products include bar stock and wire. Centrifugal casting is also used to produce short circular tubes as billets, usually to achieve a precise metallurgical structure. They are commonly used as cylinder sleeves where the inner and outer diameters are ground and machined to length. Because their size is not modified significantly, they are not always classified as semi-finished casting products.
A billet is a length of metal that has a round or square cross-section, with an area less than 36 in2 (230 cm2). Billets are created directly via continuous casting or extrusion or indirectly via hot rolling an ingot or bloom.[1][2][4] Billets are further processed via profile rolling and drawing. Final products include bar stock and wire.[3] Centrifugal casting is also used to produce short circular tubes as billets, usually to achieve a precise metallurgical structure. They are commonly used as cylinder sleeves where the inner and outer diameters are ground and machined to length. Because their size is not modified significantly, they are not always classified as semi-finished casting products.
Aluminum Billets Alloy 1XXX-9XXX Diameter 90MM/105MM/120MM/125MM/127MM/152MM/165MM,178MM/185MM/203MM/212MM/228MM/250MM/254MM/305MM/356MM/381MM/457MM Length 600-7300MM
Shubhlaxmi Industries have adapted the best methods in the manufacturing blended red chilli powder. The packet of goodness reaches not only India but across the world. India own harvesting product; Red Chilli powder is packed keeping its purity and richness intact. Red Chilli powder is commonly known as "lal mirch powder" and it is one of the key ingredients in the preparation of Indian cuisines. It is one of the main members of spice catalogue because Indians dishes are said to be incomplete without the flavor of Red chilli powder. The authentic Indian cuisines are incomplete without the touch of Red Chilli Powder in them. When you have one of the finest handpicked and selected whole chillies that are grounded with traditional methods and modern techniques, it will just come as one of the most aromatic, pungent smelling and really HOT blended Red Chilli Powder. Red Chilli powder is a dominating amongst many Indian spices. If the food is tempered with red chillies powder, its aroma can spread far off. It gives an appealing red color to delicacies with mouthwatering flavor and irresistible aroma. Specification Dried Red Chili Powder variety Hs Code : 09042211 Type sannam S4 s17 Teja byadgi kashmiri Color In Asta 35 (min) 75 (min) 90 (min) 60-90 Taste mild hot mild mild - Hot Shu Level 15000 Shu 75000 Shu 8000 Shu 10000 Max Moisture 6-8% 6-8% 6-8% 6-8% Mesh Size 20-60mm 20-60mm 20-60mm 20-60mm Total Ash 9.5% Max 9.5% Max 9.5% Max 9.5% Max Para Red, Rhodamin B, Butter Yellow absent absent absent absent Orange 2, Orange B & G absent absent absent absent Sudan 1,2,3,4 absent absent absent absent Aflatoxin Range ; 5-30 Ppb 5-30 Ppb 5-30 Ppb 5-30 Ppb Quality Assurance ; Sgs, Geo-chem, Spice Board Loading Capacity : 18mt In 20'fcl & 26mt In 40'fcl Packing : 10/25/50 Kg. New Multi Wall Paper Bag
