Metallized YIG Microwave ferrite substrate Technical requirements: 1- The Ferrite Thickness should be 0.37mm. In the process of ferrite production, fine grinding method should be used. The surface of the ferrite should be polished (To reduce the roughness). Material:CY1780 2- Use a soft gold coating. Clad layer: Cu1m4mAu2.5m5.7m. The plating thickness should be 8~10m(Red area ). 3- The bottom side will be attached to a Gold plated carrier by soldering. The solder paste model can be Pb63Sn37. The carrier material is Iron. Clad layer: Cu36mNi14m Au12m. The final carrier dimensions (after plating) are 12mm X 9mm X 0.5mm. 4- The resistive layer should be 75 Ohm/Sq. The final resistor should be 50 Ohm (+/-10% tolerance) (Green area)
Metallized YIG Microwave ferrite substrate Technical requirements: 1- The Ferrite Thickness should be 0.37mm. In the process of ferrite production, fine grinding method should be used. The surface of the ferrite should be polished (To reduce the roughness). Material:CY1780 2- Use a soft gold coating. Clad layer: Cu1 m 4 m Au2.5 m 5.7 m. The plating thickness should be 8~10 m(Red area ). 3- The bottom side will be attached to a Gold plated carrier by soldering. The solder paste model can be Pb63Sn37. The carrier material is Iron. Clad layer: Cu3 6 m Ni1 4 m Au1 2 m. The final carrier dimensions (after plating) are 12mm X 9mm X 0.5mm. 4- The resistive layer should be 75 Ohm/Sq. The final resistor should be 50 Ohm (+/-10% tolerance) (Green area)
Metallized microwave ferrite substrate for antenna use
Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor
Microwave ferrite substrate: Size:60*48*1mm;60*48*0.5mm;48*30*1mm;48*30*0.5mm SATURATION MAGNETISATION (GAUSS):1750-1800 DIELECTRIC CONSTANT:15,0 ±5% DIELECTRIC LOSS TANGENT: 0.0002 CURIE TEMPERATURE (NOMINAL VALUE)(°C):280 LINE WIDTH (Oe):25 SPIN WAVE LINE WIDTH (Oe):2 FINISH: CLEAN.
430 Annealed Stainless Steel Strip Extra Bright Annealed Soft Temper 430 Stainless Strip Steel is the most popular of all the straight chrome stainless steels Its principal use is for decorative purposes Because of its excellent heat and corrosion resistant properties its ductility and because it costs less than the chromenickel grades this Type 430 Stainless Steel Strip is used in countless applications These uses are primarily for stainless and decorative purposes including household appliances metal molding metal trim cabinet hardware hinges drawn and formed parts and stampings Type 430 Ferritic Stainless Steel Strip Characterisings Corrosion and heat resistant Ductility at about 75 of low carbon strip Similar to chromium grades with stretcher strains Roping can result from excessive stretching Able to weld for nonrigorous service Magnetic in all conditions Tensile strength annealed condition minimum of 65000 PSI yield of 30000 PSI elongation at 22
Metallized microwave ferrite substrate for antenna use.
Microwave ferrite substrate: Size:60*48*1mm;60*48*0.5mm;48*30*1mm;48*30*0.5mm SATURATION MAGNETISATION (GAUSS):1750-1800 DIELECTRIC CONSTANT:15,0 ±5% DIELECTRIC LOSS TANGENT: 0.0002 CURIE TEMPERATURE (NOMINAL VALUE)(°C):280 LINE WIDTH (Oe):25 SPIN WAVE LINE WIDTH (Oe):2 FINISH: CLEAN.
1.Polyethylene glycol series products can be used in pharmaceuticals. Polyethylene glycol with low relative molecular weight can be used as solvent, co-solvent, O/W emulsifier and stabilizer, used to make cement suspensions, emulsions, injections, etc., and also used as water-soluble ointment matrix and suppository matrix, solid waxy polyethylene glycol with high relative molecular weight is often used to increase the viscosity and solidification of low molecular weight liquid PEG, as well as compensate other drugs; For drugs that are not easily soluble in water, this product can be used as a carrier of solid dispersant to achieve the purpose of solid dispersion, PEG4000, PEG6000 is a good coating material, hydrophilic polishing materials, film and capsule materials, plasticizers, lubricants and drop pill matrix, for the preparation of tablets, pills, capsules, microencapsulations, etc. 2.PEG4000 and PEG6000 are used as excipients in the pharmaceutical industry for the preparation of suppositories and ointments; It is used as a finishing agent in the paper industry to increase the gloss and smoothness of paper; In the rubber industry, as an additive, it increases the lubricity and plasticity of rubber products, reduces power consumption during processing, and prolongs the service life of rubber products. 3.Polyethylene glycol series products can be used as raw materials for ester surfactants. 4.PEG-200 can be used as a medium for organic synthesis and a heat carrier with high requirements, and is used as a moisturizer, inorganic salt solubilizer, and viscosity adjuster in the daily chemical industry; Used as softener and antistatic agent in the textile industry; It is used as a wetting agent in the paper and pesticide industry. 5.PEG-400, PEG-600, PEG-800 are used as substrates for medicine and cosmetics, lubricants and wetting agents for rubber industry and textile industry. PEG-600 is added to the electrolyte in the metal industry to enhance the grinding effect and enhance the luster of the metal surface. 6.PEG-1000, PEG-1500 is used as a matrix or lubricant and softener in the pharmaceutical, textile and cosmetic industries; Used as a dispersant in the coating industry; Improve the water dispersibility and flexibility of the resin, the dosage is 20~30%; The ink can improve the solubility of the dye and reduce its volatility, which is especially suitable in wax paper and ink pad ink, and can also be used in ballpoint pen ink to adjust ink viscosity; In the rubber industry as a dispersant, promote vulcanization, used as a dispersant for carbon black filler. 7.PEG-2000, PEG-3000 are used as metal processing casting agents, metal wire drawing, stamping or forming lubricants and cutting fluids, grinding cooling lubricants and polishes, welding agents, etc.; It is used as a lubricant in the paper industry, etc., and is also used as a hot melt adhesive to increase rapid rewetting capacity. 8.PEG-4000 and PEG-6000 . 9.PEG8000 .
Metallic Honeycomb Catalyst is suitable for automobile exhaust purification catalytic converters , industrial waste gas purification and other fields. It can meet the increasing requirements of environmental protection .We also supply Catalytic Converter, Catalytic muffler, Motorcycle catalytic converter, DPF,DOC Catalyst, SCR catalyst ,TWC catalyst,Ceramic honeycomb monolith , Metal honeycomb carrier, ect. Our management system has been certified the ISO9001 and TS16949 by SGS company.  We offer the most diverse metallic substrate configurations in the world.All shapes can be made with or without mantels. Sizing for rounds, ovals and rectangles up to 48" - 1200mm OD Custom cell configurations available  SubstrateConfigurationsShapes can be made with or without mantels/tube Custom shapes that may not be shown here are also available upon request Custom foil geometries available Extensive product offering with variable cell sizes and flow depth options  SubstrateConstructionBrazed, Oxidized & Mechanically Retained Single brazed rounds as large as 48"OD (1200mm) Rectangles up to 48" (1200mm)  Standard Metallic Substrate Nomenclature Metal Substrates without mantels Metal Substrates with mantels Matrix OD x Matrix length x CPSIMatrix OD(Mantel OD)x Matrix length(Mantel Length) Example: 6.5 inch x 3.5 inch x 300CPSI Example:6.38 inch (6.5 inch ) x 3.5 inch (4.0 inch) x 300CPSI Cell densities - CPSI Stock foil widths Rounds in Mantels (air flow depth) Available tube sizes smaller 6� OD 25 260 Inches mm Inches mm 50 300 1 25 1 25 70 350 1.7 43 1.25 32 80 400 2 51 1.5 38 100 500 2.25 57 1.75 44 150 600 2.5 64 2 51 200 900 2.75 70 2.25 57 230 1000 3 76 2.5 64 Custom sizes also available upon request 3.25 83 2.75 70 3.5 89 3 76 4 102 3.25 83 4.72 120 3.5 89 5 127 4 102 5.91 150 5 127 12 305 6 152 Any OD larger than 6� is available
Metallized microwave ferrite substrate for antenna use.
We present a comprehensible range of Stainless Steel Sheets that are fabricated from first-rate steel. Stainless Steel Metal Sheets are used in multiple industries for their particular industrial applications. Known for its high strength, durability and easy fabrication properties, Stainless Steel Metal Sheets are high in demand. In addition to this, we provide availability of Stainless Steel Sheets in tailor-made specifications as per the requirements of customers. We are called upon as one of the most prominent Stainless Steel Sheet Metal Authorized dealer, Supplier from India Grades Austenitic Steel:301, 304, 304H, 304L, 310, 310S, 316, 316L, 317, 317L, 321, 347 Ferritic Steel:409, 409M, 410s, 420, 430 Martensitic Steel: 410, 416, 420, 431 Specification Thickness:0.4 mm Width:100 mm Length:As Required Finishes:2B, No.1, BA, MAtt, No.8, PVC
"CPU scrap board" typically refers to the circuit boards or electronic components that come from discarded or obsolete computer central processing units (CPUs) and related electronic devices. These boards contain various materials, including metals, plastics, and small electronic components. Here are some key points about CPU scrap boards: Composition: CPU scrap boards are composed of a substrate, often made of fiberglass or other materials, on which electronic components are mounted. These components include microprocessors, memory chips, resistors, capacitors, and other integrated circuits. Metals Content: The boards may contain valuable metals, such as gold, silver, copper, and palladium. These metals are often used in the manufacturing of electronic components for their electrical conductivity and corrosion resistance. Recovery of Precious Metals: Recycling CPU scrap boards is a common practice to recover precious metals. Precious metal reclamation is typically done through processes like mechanical separation, chemical leaching, and refining. Environmental Considerations: Recycling CPU scrap boards is important for environmental reasons. It helps reduce electronic waste (e-waste) and minimizes the environmental impact associated with the disposal of electronic components. Economic Value: The recycling of CPU scrap boards can have economic benefits due to the recovery of precious metals. The value of the scrap depends on the market prices of the metals at the time of recycling. Processing Methods: Various methods are used to process CPU scrap boards for recycling, including manual dismantling, mechanical shredding, and chemical processes to extract metals. Regulations: There are regulations and guidelines in many regions regarding the proper disposal and recycling of electronic waste, including CPU scrap boards. It's important to adhere to these regulations to ensure environmentally responsible practices.
2205 stainless steel, also known as duplex stainless steel, is a type of stainless steel that is characterized by its two-phase microstructure consisting of both austenitic and ferritic phases. This combination of phases provides the alloy with improved strength and corrosion resistance compared to standard austenitic stainless steels. Some of the key properties of 2205 stainless steel include: High strength: 2205 stainless steel has excellent strength properties, making it suitable for use in demanding applications such as structural components and pressure vessels. Corrosion resistance: 2205 stainless steel provides good corrosion resistance in a variety of environments, including chloride-containing and acidic environments. Weldability: 2205 stainless steel is easily weldable using common welding techniques and does not require preheating or post-weld heat treatment. Fatigue resistance: 2205 stainless steel has good fatigue resistance, which makes it suitable for use in applications where cyclic loading is present. High toughness: 2205 stainless steel exhibits high toughness even at low temperatures, making it suitable for use in cryogenic applications. Overall, 2205 stainless steel is a highly versatile material that offers excellent strength and corrosion resistance properties, making it ideal for use in a wide range of demanding applications. Here are some of the most common international standards for 2205 duplex stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A789/A789M: Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing for General Service ASTM A790/A790M: Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Pipe EN 10088-2: Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 10216-5: Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes NACE MR0175: Sulfide stress cracking-resistant metallic materials for oilfield equipment NORSOK MDS D45: Qualification of manufacturers of duplex stainless steels UNS S31803/S32205: Unified numbering system designations for duplex stainless steels We can provide the following form:2205 stainless steel coil; 2205 stainless stee strip;2205 stainless stee plate; 2205stainless steel sheets; 2205 stainless steel tubes; 2205stainless steel pipe;2205 stainless steel flat; 2205 stainless steel bar
Microwave Ferrite Technology, Inc. is the largest manufacturer of microwave ferrite materials in China, producing tens of millions of pieces each year for the wireless industry. The products range from high volume garnets for wireless infrastructure to specialized materials for radar applications. Our Ferrites & Magnetic Materials include: Narrow Linewidth Aluminum & Aluminum Gadolinium Substituted Garnets Gadolinum Substituted Garnets Cobalt & Holmium Doped Garnets Magnesium Spinels Nickel Spinels Lithium Spinels If you have any questions or need further details, feel free to contact us
TTVG-1850 Microwave ferrite for microwave switch
Product shape of circular, annular, fan. The products are mainly applied to circulator, isolator and so on. For more information,
Triangle Microwave ferrite for the isolator(10kw 2.45ghz ) in MPCVD in Artificial diamond industry. NOTE One isolator needs to be equipped with 24 pieces of triangle microwave ferrite.
Microwave ferrite(A50) for phase shifter Li Zn - Ti - Mn - (Co) Lithium - Zinc - Titanium Manganese - (Cobalt) MS(Gauss) :5000gs±5% Tc (°C) :450 H (Oe) 170 ±20% Hk (Oe) 3±5% DIELECTRIC CONSTANT15.3 DIELECTRIC LOSS TANGENT 0.0005 Br (Gauss) 3300
Microwave ferrite(A50) for phase shifter Li Zn - Ti - Mn - (Co) Lithium - Zinc - Titanium Manganese - (Cobalt) MS(Gauss) :5000gs±5% Tc (°C) :450 H (Oe) 170 ±20% Hk (Oe) 3±5% DIELECTRIC CONSTANT15.3 DIELECTRIC LOSS TANGENT 0.0005 Br (Gauss) 3300