The purpose of the test instrument is to calculate the maximum and minimum of cohesive soil porosity, and used to calculate the relative density, to understand the soil in the state of nature or the elastic after compaction and the stability of soil grain structure.
We supply 25mm, 26mm Plain Particle Boards for filling inside the doors. 2440x1220x26mm plain particle board shall weigh about 40kgs. We do particle board starting 9mm to 40mm and above for various purposes like lamination grade fully sanded on both faces, for routing purpose, furniture backing etc. 26mm(non sanded) :520Kg/m3 - E2 Grade 30 to 64mm- E1, High Moisture Resistance, Both Sides sanded 26mm(non sanded) :520Kg/m3 - E2 Grade 30 to 64mm- E1, High Moisture Resistance, Both Sides sanded, suitable for Fire door -tested to BS standard We can also adjust the density of board as per our customer requirement. Our plain particle boards are priced competitive. Please contact us for more details.
The Tire derived Steel or Tire Wire Scrap is a light melting scrap obtained during the shredding and granulation process of used tires. Generally 10% - 20% of the weight of an old passenger car tyre usually consists of steel. An average shredding plant produces about 100-200 MT of steel tyre wire and its quality can vary according to technology, storing and management systems adopted by the producing plants. We can provide tire wire scrap that still contains up to 20% rubber/fiber. This percentage is detected by manual separation test. The material can be loaded loose in 40 HC container. For further details, please feel free to contact us.
We are proposing about 2000tons of iron slag derived from the desulphurisation skimming process. This material is a iron by- product that is encapsulated in varying levels of contaminants (S,Mg,Si). In order to enhance its usability, the material is processed and screened. We can propose two specifications of Iron Slag - European Code: 19.12.01 - Basel Code: B1010 - HS Code: 2619.0020 - Quantity: 2000 tons currently available - Monthly quantity: 500-1000 tons depending on production - Size: 350 1200 mm - Fe content: from 77 to 86% - C content: above 2,5-3% - Bulk density: 2,8-3,4 tons/m3 - Loading type: loose in 20 (26-27 tons on average) The level of Fe% in the slag has been estimated by water displacement test. For any further information please feel free to contact us
The mentha water is steam distilled from fresh blossoms Bulgarian mentha piperita of during the months of may and June of each year. It is a completely natural product for skin and hair application. Transparent liquid, colorless; specific aroma; essential oil content 0.03, ethyl alcohol content 3.44, relative density 20 C 0.9827, PH 5.25, microbiological purity - corresponds to standard. Benefits: Has an antiseptic and anti-inflammatory effect on the skin. Soothes the skin after sunburns or razor cuts. Gently cleanses and tightens the pores of the oily skin. Moisturizes the skin and improves its general condition.
Commodity: Sodium Bisulfite Molecular Formula: NaHSO3 Molecular Weight: 104.06 Properties: White monoclinic crystalline powder with sulfur dioxide odor; relative density: 1.49; very easily soluble in water; can be decomposed when heated; slightly soluble in ethanol; aqueous solution is acidic; has strong reducing property; can be oxidized in the air or loose sulfur dioxide. Quality Standard: HG/T3492-80 Technical Indicator High-purity grade Acrylic grade Food grade Refined grade Industrial grade 1 NaHSO3 % 99.5 Insol. in water % 0.003, 0.005, 0.03, 0.04, 0.05 Chloride(Cl) % 0.003, 0.004 Iron(Fe) % 0.001 0.002 0.005 Heavy metal(Pb) 0.001 Arsenic(As) % 0.0001 Clarity test Qualified Use: It is used in the bleaching of cotton textiles; as reducing agent in dyes, paper-making, leather, chemical synthesis; in the manufacture of pharmaceutical intermediates, developer, food bleacher, antiseptic and anti-oxidants. Packing: In PP woven bag lined with PE bag; paper-plastic composite bag, and kraft paper bag etc. Net wt.: 25/50/1000 kgs/bag or upon clients' request.
Checking Item Test Standard Sodium oxide(Na2O)% 28.00-30.00 Silica(SiO2)% 27.00-29.00 Water insoluble% 0.2 Fe(ppm) 200ppm Whiteness% 80 Bulk Density 0.80-0.97g/cc PH of 1.0% Solution 12-13 Melting Point 72.2 ParticularSize % (16-30mesh) 90 98
1. Product name: Ammonium bisulfite solution 2. Molecular formula: NH4HSO3 3. Molecular weight: 99.10 4. Physical and chemical properties: light yellow liquid, with a little sulfur dioxide odor. Relative density (70%) : 1.4. 5. Technical index: Item Photographic grade Appearance clear light yellow liquid Content w/w % 68-72 pH value (stock solution 20C) 4.0-6.0 Iron (Fe) w/w % 0.001 6. Packing: 270kg plastic drum, 1.25MTS/IBC 7. Uses: in synthesizing dye intermediate, surfactant, herbicide, reducing agent in pharmaceutical industry, etc.
4-Hydroxybenzoic acid Chemical Name:4-Hydroxybenzoic acid Trade Name:p-oxybenzoic acid Molecular Formula:C7H6O3 Molecular Weight:138.12 CAS No.:99-96-7 Properties:white odorless crystalline powder, easily soluble in hot water and alcohols, aethers and acetone, slightly soluble in cold water and benzene, insoluble in carbon bisulfide; relative density is 1.46 Use: Can be used as antiseptic, intermediate of dyes, pharmaceuticals; as main material of liquid crystal polymers; as material of pesticide intermediate Specification Item Specification Polymer Grade Technical Grade Appearance white crystal powder white crystal powder Purity(on dry base) % 99.6 99.0 Melting Point 214-217 212-216 Odor odorless odorless Solubility Clear and transparent clear and transparent Loss on Drying % 0.20 0.50 Color(Pt-Co) 10 40 Ash % 0.02 0.15 Sulfate(SO42-) 0.01 0.05 Chloride(Cl-) % 0.005 0.02 Phe% 0.01 0.10 Salicylic Acid % 0.02 0.10 4-Hydroxyisophthalic Acid(HIPA) ppm 500 / Insolubles in Metha ppm 50 / Potassium(K+) ppm 5 / Sodium (Na+) ppm 5 / Iron (Fe) ppm 5 / Ca2++Mg2+ppm 5 /
Chemical name:Magnesium nitrate Molecular formula:Mg(NO3)2.6H2O Molecular weight:256.40 Property:soluble in water,liquid ammonia, methanol and ethanol.Stable at room temperature, the relative density of 1.461, higher than the melting point of 95�°C off the water to generate alkaline magnesium nitrate, heated to 300�°C begins to decompose above 400�°C to completely decompose into magnesium oxide and Nitrogen oxide gas. Quality standard: Item Indicator Industrial grade Agriculture grade Magnesium nitrate (Mg(NO3)2.6H2O) â?¥98.0% â?¥98.0% PH value â?¥4 --- Heavy metal â?¤0.002 --- Water insoluble â?¤0.05% â?¤0.1% Iron â?¤0.001% --- Magnesium oxide content(CaO) --- â?¥15% Nitrogen content(N) --- â?¥10.7% Use:Concentrated nitric acid for industrial de-water agent, manufacture of explosives, catalysts and other magnesium salts and nitrates catalyst raw materials, wheat ashing agent.Used in agriculture, magnesium soluble fertilizer for soilless culture. Packing:25/50KGlined with plastic bag and exterior is woven bagPacking or according to customers requirements. 1.Purity 98% white granule 2.Used for fertilizer or industrial material 3.Export Asia/Europe 4.ISO9001
Commodity: Sodium Hydrosulfite Other name: Synonyms: Sodium Hydrosulphite; Sodium Dithionite; Dithionous acid, Disodium salt; Sodium Sulfoxylate CAS No.: 7775-14-6 Molecular Weight: 174.10 Chemical Formula: Na2S2O4 Product Description Appearance: White, crystalline powder. Product Feature Odor: Slight irritative. Specific Gravity: Unavailable Solubility: Soluble in water. Density: 2.19 pH: 6-7 pH Test-Method: PH test paper. % Volatiles by volume @ 21C (70F): 0 Boiling Point: Not applicable. Melting Point: >300 C Decomposes. Vapor Pressure (mm Hg): No information found. Bulk Density: ~0.9 Evaporation Rate (BuAc=1): No information found. Application 1. Widely used in textile industry for vat dyeing, reduction cleaning, printing and stripping, textile textile bleaching . 2. bleaching paper pulps , especially mechanical pulps, its the most fittable bleaching agent in pulps. 3. bleaching kaolin clay, fur bleaching and reductive whitening, bleaching of bamboo products and straw products, 4. in mineral, the compound of thiourea and other sulphides. 5. as reducing agent in chemical industry. 6. Sodium hydrosulfite food additive grade is used in foodstuffs, as bleaching agent and preservative dried fruits, dried vegetable, vermicelli, glucose, sugar, rock sugar, caramel, candy, liquid glucose, bamboo shoots, mushrooms and canned mushrooms. Packaging 50kg/100kg net in iron drums with double PVC bags Product Specification/Models NDEX 90%, 88%, 85%. FOOD ADDITIVE Na2S2O4, 90%, 88%, 85%, Fe 20ppm ZincZnOther heavy metal calculated as Pb, 1ppm Water Insolubles05% Shelf Life(month)12
Potassium Monopersulfate compound, a white, free flowing crystalline granule, is non-toxic, odorless, and easily soluble in water. It is an efficient, environmentally friendly, and multifunctional acidic oxidant. General Information Product Name Potassium Monopersulfate compound CAS 70693-62-8 Chemical formula 2KHSO5 KHSO4 K2SO4 Molecular weight 614.7 Specification Appearance White, free flowing granule Available Oxygen, % 4.5 KHSO5,  % 42.8 Loss on Drying  % 0.15 Bulk Density, g/L 0.80 pH (10g/L,25 C) 2.0 .4 Sieve Residue on 75 m test sieve, % 90.0 Packaging Product is packaged in plastic woven bags lined with polyethylene film, with a net weight of 20kg/bag or 50kg, or the packaging form and net content can be determined through negotiation according to customer requirements. Storage Store in a cool and well ventilated warehouse to prevent exposure to sunlight, rain, and moisture. Prohibit mixing with reducing substances for storage.
We are supplier and exporter of PVC Resin. PVC resin, the physical appearance is white powder, non-toxic, odorless. Relative density 1.35-1.46. It is thermoplastic, insoluble in water, gasoline and ethanol, expandable or soluble in ether, ketone, fatty chlorohy-drocarbons or aromatic hydrocarbons with strong anti--corrosiveness, and good dieletric property. PVC resin can be processed into various plastic products.
Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor
PRODUCT DATA SHEET ACID RESISTANT BRICK Material : RED SHALE Type Acid Resistant Brick Size (mm) 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions Heavy thermal shock Typical Physical Properties of GANESHAS Acid and Chemical Resistant Brick Characteristic RED SHALE ACID RESISTANT BRICK Test Standard Bulk Density, gm/cc - 2.3 to 2.35 ASTM C-20 -Water Absorption, % - 0.1 to 1.5 IS 4860-1968 Apparent Porosity, % -0.5 to 1.75 S 4860 Acid Solubility (H2SO4), Loss in Mass,% -0.1 to 1.8 ASTM C-279 Modulus of Rupture, PSI -2133 to 3555 ASTM C-67 Compressive Strength, Kg/cm2 - 700-900 IS 4860-1968 Abrasion Resistant , Volume in mm3 -69 to 85 EN 102 Surface Hardness, MOHS Scale - 7
PRODUCT DATA SHEET ACID RESISTANT BRICK Material : FIRECLAY Type Acid Resistant Brick Size (mm) : 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : * We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: * Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions - Heavy thermal shock Characteristic Fireclay Type Acid Resistant Brick - Test Standard Bulk Density, lbs/ft3 - 2.25 to 2.30 ASTM C-20 Water Absorption, % - 0.1 to 1.8 ASTM C-20 Apparent Porosity, % - 4.05 to 4.14 ASTM C-20 Acid Solubility (H2SO4), Loss in Mass,% - 6.1 to 6.8 ASTM C-279 Modulus of Rupture, Mpa - 14.6 ASTM C-67 Compressive Strength, PSI - 15500 to 17250 ASTM C-67 Abrasion Resistant , Volume in mm3 - 71 to 96 EN 102 Surface Hardness, MOHS Scale - 7 Thermal Conductivity, BTU-in/hr-ft-F - 6.94 to 7.12 ASTM C-236 Thermal Expansion Coefficient,in/in/Fx10-6 - 2.6 to 2.8 EN 103
About THE Product : Blast furnace slag is used in the production of cement (iron Portland and blast furnace cement). Air-cooled blast furnace slag is formed by allowing the molten slag to cool relatively slowly under ambient conditions; final cooling can be accelerated with a water spray. The cooled material is hard and dense, although it can have a vesicular texture with closed pores. After crushing and screening, air-cooled slag can be used in several applications. Granulated slag is formed by quenching molten slag in water to form sand-sized particles of glass. The disordered structure of this glass gives the material moderate hydraulic cementitious properties when very finely ground into granulated blast furnace slag, but if it can access free lime, the granulated blast furnace slag develops strong hydraulic cementitious properties. Pelletized or expanded slag is cooled through a water jet, which leads to rapid steam generation and the development of innumerable vesicles within the slag. The vesicular texture reduces the overall density of the slag and allows for good mechanical binding with hydraulic cement paste. Blast Furance Slag is a nonmetallic co-product which is produced in the process of iron manufacturing, Granulated Blast Furnace Slag is a glassy granular material formed when molten blast furnace slag is rapidly cooled by direct water. Rapid cooling prohibits the formation of crystals and forms glassy, non-metallic, silicates and alumino silicates of calcium. GBFS : (Granulated Blast Furnace Slag) Source : Granulated BF Slag From Gujarat State, India Supply Quantity : 50,000 Metric Tons Per Month Packing: Bulk Parameters (% BY MASS) CaO 30-38 Al2O3 15-20 SiO2 30-40 Glass Content 85-97 MgO 8-11 Fe2O3 0.5-1.5 Moisture 10 MAX Size -5mm Min 95, +5 mm Max 5 Relative Gravity 2.9 Bulk Density(Bagged) 1200 KG/M3
HDPE repro pellet white color, post consumer MFI: 0.25-0.30 Density 0.97 ( ISO: 1183) Test report as photo On going shpt
rLDPE repro Yellow pellets from post-consumer & post-industrial films. The material is shredded and washed through a wash plant before it is processed through degassing and very fine filtration to produce high purity reprocessed resin. r-LDPE yellow is a blown film grade and exhibits excellent processability and good balance of toughness, strength and stretch properties. This grade is also be suitable for profile and sheet extrusion Packing: 1000kg bulk bag Melt flow rate (190�?C / 2.16kg) 0.5 �± 0.5 Density 0.92 �± 0.015 Measured on blown film of 25 �µm and BUR of 2.5 at external testing facility. rLDPE Yellow is typically extruded at a melt temperature around 190�?C (min 180�?C, max 240�?C). Mesh filters: 150 on the laser filter and 120 on the piston filters.
Origin: United Kingdom Material: LDPE Repro pellets Yellow Category: LDPE Type: Repro pellets Color: Yellow Quantity: 500 Tons Loading weight: 24 Tons Specification: "rLDPE repro Yellow pellets from post-consumer & post-industrial films. The material is shredded and washed through a wash plant before it is processed through degassing and very fine filtration to produce high purity reprocessed resin. toughness, strength and stretch properties. This grade is also be suitable for profile and sheet extrusion Packing: 1000kg bulk bag Melt flow rate (190�?C / 2.16kg) 0.5 � 0.5 Density 0.92 � 0.015 Measured on blown film of 25 �m and BUR of 2.5 at external testing facility. rLDPE Yellow is typically extruded at a melt temperature around 190�?C (min 180�?C, max 240�?C). Mesh filters: 150 on the laser filter and 120 on the piston filters."
