Compared with conventional casting magnesium alloys, our semi-continuous casting magnesium alloys are finer in the organization, more uniform on the ingredients, and more compact inside. They have higher strength and elongation, and are applied to magnesium alloy processed products, rods, bars, tubes, plates, sheets, wires, etc.. By secondary refining, the magnesium alloys manufactured by yirui company have higher purity and lower impurity. The magnesium liquid is poured directly from the heat holding furnace, and crystallizes rapidly. This improves the compactness of internal microstructure of the magnesium rods. The internal crystal are more compact, and the physical performance is greatly enhanced compared to the conventional casting products.
Magnesium alloy castings can be produced by nearly all of the conventional casting methods, namely, sand, permanent, die-casting, etc.. How to choose the right casting method of a particular part depends on many factors such as its application, the properties required, the properties of the alloy, and the proposed design. Yirui magnesium, certified by iso9001:2008, is a professional manufacturer specialized in magnesium alloys. We provide all work in compliance with the astm standards. We guarantee that all of our products have the right chemical properties. No product leaves our company before being tested, inspected and approved.
Yirui magnesium offers az63 cast anode rods in compliance with the current astm b843 standard. We will produce your specific part from start to finish.
All the products are supplied to the standard astm b107. Basically, magnesium alloys az31b, az31s, az61a and az80a are available. In addition, we have the capability to provide custom alloys extrusion profiles.
Magnesium alloy extrusions, magnesium alloy semi-continuous casting rods and plates, cast, extruded magnesium anode rods for water heaters & storage tanks, magnesium, aluminum, zinc sacrificial galvanic anodes.
Our company is a professional manufacturer of magnesium extrusions in rods, bars, solid shapes, structural shapes, wires, tubes, hollow shapes and semi-hollow shapes. We are offered in a variety of standard alloys and forms as well as many special shapes tailored to a customer's particular requirements. Alloys available: zm21, az31b, az61a, az80a zk60a, we54a and we43a.
Extruded magnesium alloy bars, profiles and tubes Our company is a professional manufacturer of magnesium extrusions in rods, bars, solid shapes, structural shapes, wires, tubes, hollow shapes and semi-hollow shapes. We are offered in a variety of standard alloys and forms as well as many special shapes tailored to a customer's particular requirements. Alloys available: zm21, az31b, az61a, az80a zk60a, we54a and we43a.
The mg alloy has the good specification of casting, pressing, cutting, welding and processing, it can be processed into a plate, strip, tube, rod, bar and wire etc. Semi-continuous casting magnesium alloy rod:70-600 mm( dia.) Deformed magnesium alloy plate:10-300 mm(width), 0.5-100 mm(thickness) Deformed magnesium alloy shapes: 10-140 mm(dia.)
1. Lower specific gravity and negative potential. 2. High driving voltage to the iron and lower current efficiency. 3. Large generating capacity per unit and long service life.
We are engaged in making Lead available in several forms including LME registered and non registered 99.97% and 99.99% as well as secondary ingots, foil, granules, powder, rod, shot, sheet, and wire. Lead is a bluish-white lustrous metal. It is very soft, highly malleable, ductile, and a relatively poor conductor of electricity. It is very resistant to corrosion but tarnishes upon exposure to air. Alloys include pewter and solder.
We hold immense expertise in making available Copper in many forms including LME registered and non registered cathodes, billets, rods, cakes, bars, foil, sheet, granules, plates, powder, shot, turnings, wire, insulated wire, mesh and “evaporation slugs”. Copper is one of the most important metals. Copper is reddish with a bright metallic lustre. It is malleable, ductile, and a good conductor of heat and electricity (second only to silver in electrical conductivity). Its alloys, brass and bronze, are very important. Monel and gun metals also contain copper. The most important compounds are the oxide and the sulphate, (blue vitriol
Raw melting material - aluminum scraps, cans, engine waste etc. Output capacity - 5-30 tons/h, customized Automation - Full automatic/ half automatic (based on output requirement and investment budget Ingot type - ADC12 (7.5kg/ 10kg / customized) 1. After cleaning the oil and grease of waste aluminum, manually put it into the furnace with a forklift; 2. Ignition for melting furnace .Heat up to 680C, and input appropriate proportion of alloy elements. Heat up to 800C, melt and stir evenly, then fetch samples to the spectrometer for testing. Every lot of production need to do testing . 3. Put A tool that attracts iron into the furnace by forklift, to suck away the iron in the aluminum water. 4. Put the slag agent into Alu liquid to remove the slag. After slag removed , put the slags into Aluminum ash separation machine , and let the aluminum water and ash separate. The proportion of slag agent and aluminum liquid is 1:500 5.Open the drain valve and the aluminum water flows automatically to the ingot production line After the ingot casting is completed, the ingot stacking robot will stack the ingots, which means the production is completed.
Sweet marjoram: Origanum (O) hortensis (orMajoranahortensis). Potmarjoram: O.onites Wildmajoram: O.vulgare. Syrian majoram is called zatar Family: Labiatae or Lamiaceae (mint family). In Europe, marjoram was a traditional symbol of youth and romantic love. Used by Romans as an aphrodisiac, it was used to cast love spells and was worn at weddings as a sign of happiness during the middle Ages. Greeks who wore marjoram wreaths at weddings called it “joy of the mountains.” It was used to brew beer before hops was discovered, and flavored a wine called hippocras. A cousin of the oregano family, marjoram originated in Mediterranean regions and is now a commonly used spice in many parts of Europe. Called zatar in the Middle east and often mistaken for oregano, it is also a popular spicing in Eastern Europe. Origin and Varieties Marjoram is indigenous to northern Africa and southwest Asia. It is cultivated around the Mediterranean, in England, Central and Eastern Europe, South America, the United States, and India. Description Marjoram leaf is used fresh, as whole or chopped, and dried whole or broken, and ground. The flowering tops and seeds, which are not as strong as the leaves, are also used as flavorings. Sweet marjoram is a small and oval-shaped leaf. It is light green with a greyish tint. Marjoram is fresh, spicy, bitter, and slightly pungent with camphor like notes. It has the fragrant herbaceous and delicate, sweet aroma of thyme and sweet basil. Pot marjoram is bitter and less sweet. Chemical Components Sweet marjoram has 0.3% to 1% essential oil, mostly monoterpenes. It is yellowish to dark greenish brown in color. It mainly consists of cis-sabinene hydrate (8% to 40%), -terpinene (10%), a-terpinene (7.6%), linalyl acetate (2.2%), terpinen 4-ol (18% to 48%), myrcene (1.0%), linalool (9% to 39%), -cymene (3.2%), caryophyllene (2.6%), and a-terpineol (7.6%). Its flavor varies widely depending on its origins. The Indian and Turkish sweet marjorams have more d-linalool, caryophyllene, carvacrol, and eugenol. Its oleoresin is dark green, and 2.5 lb. are equivalent to 100 lb. of freshly ground marjoram. Marjoram contains calcium, iron, magnesium, phosphorus, potassium, sodium, vitamin A, vitamin C, and niacin. Culinary uses of Marjoram Marjoram is typically used in European cooking and is added to fish sauces, clam chowder, butter-based sauces, salads, tomato-based sauces, vinegar, mushroom sauces, and eggplant. In Germany, marjoram is called the “sausage herb” and is used with thyme and other spices in different types of sausages. It is usually added at the end of cooking to retain its delicate flavor or as a garnish. It goes well with vegetables including cabbages, potatoes, and beans. The seeds are used to flavor confectionary and meat products.
Commodity: Synthetic Cryolite Formula: Na3AlF6 M.W.: 209.95 Properties: The product is a white crystalline powder or a sandy-size granularity, and a pinkish crystalline powder or a sandy-size granularity as well. Sp.gr.2.953.01g/cm3, melting point about 1000centigrade, specific heat 1.056j/gcentigradeat 18100centigrade. Its slightly soluble in water, but insoluble in anhydrous hydrogen fluoride. The content of its crystal water will be decreased while the increasing of the molecular ratio, therefore its loss on ignition will be also decreased while the increasing of the molecular ratio. After the paste of synthetic cryolite with different molecular ratio dehydrates, the loss on ignition at 800centigrade will appear 10.34%, 6.22% and 2.56% when the molecular ratio reaches 1.74, 2.14 and 2.63 reactively. Specifications: Appearance white powder F 52% min Al 12% min Na 33% max SiO2 0.36% max Fe2O3 0.08% max CaO 0.5% max P2O5 0.03% max SO4 0.6% max H2O 0.4% max Loss on ignition 2 % max Uses: Its mainly used as a flux in the aluminum smelting by fused-salt electrolysis; also an opalizer in the manufacture of enamel; an opacifier and auxiliary solvent of glass and enamel; an insecticide of crops; a flux in aluminum alloy casting; and in the production of ferrous alloy and effervescing steel; as well as a wear-resistant filler for resin and rubber-boned abrasive wheels. Packing & Storage: In plastic coating woven bags with plastic film inside, 25kg,40kgs, 50kgs or 1000kgs net each, or as the requirement of clients.Stored: in a cool , ventilated, dry place.
Cast aluminum-magnesium alloy Category:Aluminum alloy casting Cast Aluminum-magnesium alloy are widely used in the fields of electronics, automobiles, and aerospace. Common grades are 7A09 etc. The main elements of aluminum-magnesium alloy include aluminum and magnesium. The alloy products have high strength, low density and strong heat dissipation capacity, so they are popular in the fields of electronics, automobiles, and aerospace. Common grades are 5052, 5754, 5083, etc. Aluminum alloys have lower cost, superior performance and stronger product competitiveness. The density of aluminum-magnesium alloy is small, so it is lighter under the same volume, and has a certain strength, which can be used for load-bearing. Aluminum-magnesium alloy has strong heat dissipation, and at the same time, it can resist electromagnetic interference and has strong electromagnetic shielding. Its appearance has a certain degree of beauty, is resistant to corrosion, can maintain a good quality of appearance for a long time, and the material is environmentally friendly, and the waste is recyclable.
Forging, casting & fabrication based finished mechanical items & assemblies from carbon, alloy & stainless steels. hook blocks for eot & mobile cranes, s.g. iron sheaves, boom extension shafts, hydraulic manifolds, hard chrome plated alloy steel pins, clevis, pivot blocks, forged eye, fork & pin for boom, twist locks, guides, pad holding blocks, tube steer axle, crank shafts, connecting rods, torque arms, pull rods, roller assemblies & sprockets, knuckle chains, redler & rivetless chains.
Ramming mass is commonly used in metallurgy, building materials, non-ferrous metal smelting, chemical, machinery and other manufacturing industries. Ramming mass is widely used in non-core intermediate frequency furnace and core induction furnace. As an intermediate frequency furnace ramming material, refractory ramming is applied to melt gray cast iron, nodular cast iron, malleable cast iron, vermicular cast iron, and cast alloy steel; to melt carbon steel, alloy steel, high manganese steel, tool steel, heat resistant steel, stainless steel, molten aluminum and its alloys; to melt red copper, brass, white brass, bronze and its alloys, etc. Induction furnaces are used for melting cast iron, mild steel and various alloy steels in foundries and making of steel in mini steel plants using sponge iron The refined high silicon, low iron quartz sand and quartz powder are selected and the fused quartz sand is added as the refractory material., with no slag, no crack, damp proof, convenience of repair, and the corrosion resistance, thus greatly improving the furnace service life span and the economic benefit.. Silica ramming mass can safely be used up to an operating temperature of 1600 deg C. Since it expands very little, it is superior to both alumina and magnesia refractories to resist thermal shocks Acid ramming material is the premixed ramming mass of the lining material. The acid ramming mass is used to smelt a series of metal materials such as ordinary steel and carbon steel. The lining practice best suited to a particular furnace depends upon the capacity and design of the furnace, operation practice adopted during making of a heat, and furnace output.
Product:Rods Brand:Renaissance Pipe Fitting Inc. Sizes:Refer the specification Condition:New Rating:4.2, based on 42 reviews price:Start from 20 USD SS Rods, ASTM B221, UNS N06600, UNS N02200, UNS N06601, UNS N08800 High Nickel Alloy Rods, supplier. RFP India is India's well-known manufacturer, supplier and exporter of Rods, which is an iron alloy with a very low carbon (less than 0.08%) content in contrast to cast iron (2.1% to 4%), and has fibrous inclusions known as slag up to 2% by weight. Many items, before they came to be made of mild steel, were produced from rods, including rivets, nails, wire, chains, rails, railway couplings, water and steam pipes, nuts, bolts, horseshoes, handrails, wagon tires, straps for timber roof trusses, and ornamental ironwork. Rods might be round, square, rectangle or flat, and flat rods might be narrow or broad. Rod iron is usually a cut from flat bar iron in a slitting mill to provide the raw material for nails.
Continuous Cast Copper Rod
Drying Type Garlic Peeling Machine Garlic dividing- peeling machine is an advanced and large-scale garlic dividing -peeling equipment, which has obtained the national invention patent. No-water garlic peeling machine The machine adopts the integrated flow mode of dividing, flaking and air stripping. The raw materials and peeled products of garlic gradually come out, with small gas consumption, high output and no noise. Besides, it is equipped with garlic waste skin extrusion molding device, which is environmentally friendly and pollution-free. The successful development of this new technology has become an important mechanical equipment in the garlic processing industry . The remarkable features of the machine are as follows 1. Garlic does not need to be cut into roots, and the equipment will automatically peel garlic petals from the root. 2. Automatically split the garlic and peel it. 3. The feeding and conveying, flaking, continuous peeling and finished product output are all automatic. 4. The machine can automatically collect the waste garlic skin and extrude it into pieces, which is convenient for waste skin treatment. 5. The machine is clean and undamaged. 6. The machine also has the characteristics of low power consumption and no noise. Have full-automatic / semi-automatic garlic peeling machine ,big capacity garlic peeling production line and customized design!