Integral Type Shenkai Double Ram BOP Rubber Seal Product Description BOP parts that we supply all come from original manufacturers, they are 100% interchangeable. Apply to below BOP: Brand: SHENKAI BOP. RONGSHENG BOP ETC OTHER FAMOUS BRAND BOP Type:Annular BOP, Single Ram BOP, Double Ram BOP, Shear Ram BOP Working pressure:2000psi-15000psi(14 Mpa-105Mpa) Operating temperature:-18deg--121deg Bore size:7 1/16"-21 1/4" Top & bottom connection:Flanged,studded Main Parameters 1)Standard: API 2)Pressure: 2000~15000psi(14-70Mpa) 3)Size:Nominal bore7 1/16~21 1/4" (179.4~539.75mm) 4) U type, S type Available 5) Shear/ Pipe/Blind Ram 6) According to the latest API Spec 16A standard,and quality standard of ISO9001.
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Brief Introduction 1.The pressure-bearing components are forged, so it has better strength and impact toughness; 2.Floating sealing is applied to the cylinder cover and the open/close of the cover is realized by hydraulic power, so it is quick and convenient for changing rams; 3.The auxiliary oil cylinder affords a smaller volume with same function; double ram Cameron U BOP 4.The ram rubber has massive storage volume, and it adopts self-contained sealing; 5.The standard configuration includes a manual locking device, which ensures the ram is closed tightly in case there is a hydraulic pressure loss; 6.Both the manual and hydraulic locking device and the auxiliary oil cylinder can be installed flexibly into different positions according to customers' requirements, and the installation positions can be changed easily.
Major Types of Natural Rubber 1. Hevea Rubber (Hevea Brasiliensis) - The primary raw material for natural rubber comes from the Hevea tree (Hevea Brasiliensis), mainly cultivated in Southeast Asia, particularly in Thailand. 2. Sumatra Rubber - Rubber is also produced in Sumatra, Indonesia, serving as another globally significant production region. Natural Rubber Supply Chain Process: 1. Cultivation and Harvesting: 2. Processing and Production: 3. Domestic and International Trade: 4. Product Manufacturing: Applications of Natural Rubber 1. Automobile Tires: - Natural rubber is a key raw material for the manufacturing of automobile tires due to its excellent wear resistance and elasticity. 2. Shoe Soles: - Widely used in the production of shoe soles, providing cushioning and durability during walking. 3. Industrial Products: - Utilized in a variety of industrial products, serving as vibration control materials and sealing materials. 4. Medical Devices: - Used in the production of medical gloves and some medical devices due to its flexibility and biocompatibility. Applications of RSS (Rubber Smoked Sheet) and TSR (Technically Specified Rubber): 1. RSS (Rubber Smoked Sheet): - Automobile Tire Manufacturing: - RSS is extensively used in the production of high-end automobile tires due to its excellent physical properties and quality, making it a reliable material for tires that require high wear resistance and durability. - High-Quality Products: - Additionally, RSS is employed in the manufacturing of other high-quality rubber products, including industrial goods, luxury consumer goods, and some medical devices. 2. TSR (Technically Specified Rubber): - Automobile Parts Manufacturing: - TSR products are widely used in the manufacturing of automobile parts. In components requiring vibration control, such as engine mounts and bushings, TSR is selected for its specific properties. - Industrial Applications: - Used in the manufacturing of industrial products, TSR is an ideal material for products where the flexibility and elasticity of rubber are essential. - Medical Devices: - TSR is also used in some medical devices, playing a crucial role in the production of medical products due to its biocompatibility.
Product Name: High Preessure Industrial Use Transformer Vacuumizer Packaging Wxf Series Anti-Explosive Oil Free Rotary Vane Vacuum Pump Summary: We have more than 20 types chemical process pump, such as horizontal pump, submersible pump ,vertical pump, semi-submersible pump, fluoroplastic pump, axial pump ,gear pump.ect . Application: They are used for transmission of liquids (oil, sea water ,sulphuric acid, phosphoric acid, H2SiF6acid, alkali liquid) with low or high temperature, neutral or corrosive liquids ,or liquids with solid granular and widely used in petroleum chemical industry ,oil refining industry, paper ,pulp industry ,sugar industry ,mining ,etc Lots of material can be chose for different working condition, such as cast steel ,stainless steel 304,316,2205,904L, Hartz alloy C276,C22, nickel-base alloy GH600, PVDF,PP, UHMWPE-lining .etc Pump a strong seal system :packing seal ,double face mechnical seal ,cartridge mechnical seal ,API682 flushing syestem.
We supply various types of UPVC pipe fittings including welded fittings there are two kinds of welded and nonwelded socket welded and threaded fittings flange fittings Ball valve straight pipe straight elbow forward Tee pipe clamp abnormal straight reducing elbow cross loose jointpipe cap copper inner wire straight copper inner wire Tee outer wire direct head loose joint direct head loose elbow double loose ball valve 45 elbow reducing ring external thread plug flange copper inner wire elbow quick joint Y filter glue 1 Fittings used for connecting pipes are flange loose joint pipe hoop clamp sleeve throat hoop etc 2 Fittings change the direction of the pipe elbow bend pipe 3 Fittings change the diameter of the pipe reducing diameter reducing pipe reducing elbow branch pipe reinforcing pipe 4 Fittings increase the pipe branch tee crossing 5 Fittings for pipe sealing gasket raw material belt thread flange blind plate pipe plug blind plate head welding plug 6 Fittings for pipe fixing clamp ring tow hook hanging ring bracket bracket pipe clamp etc
Aluminum coil plate and Aluminum foil hot-rolling strip The type of aluminum we have is 1050, 1060, 8011, 6063 1060 3003 5052 6061 7075.A380 ADC12 A390ZL101A ZL104 ZL109 ZL111 ZL205A ZL108 ZA12 4343 We can fluorocarbon paint and strip the aluminum coil into different widths, and the thickness of the aluminum foil ranges from 0.18-10mm. As well as can provide thermal insulation aluminum coil, color aluminum coil, with pattern aluminum coil, without viscosity, double-sided conductive high-quality aluminum. It can also be processed into different profiles. As a new type of metal material, aluminum alloy plate has been widely used in various fields in recent years. Its characteristics are in the following aspects: 1. Light weight and high strength. 2. Good corrosion resistance. 3. Good thermal conductivity. 4. Beautiful and practical. Aluminum foil and aluminum coil, as the two main forms of aluminum materials, are widely used in many industries. Although they are of the same origin, they differ in their characteristics and uses. Aluminum foil, known for its thin and flexible, thickness is usually less than 0.2mm, is the ideal choice for food packaging, electronics industry. The aluminum coil, with a thickness greater than 0.2mm, is known for its robustness and durability, and is often used in the construction field of roofs, wallboards and so on. In the field of application, aluminum foil shines in food packaging with its good sealing and toughness, such as the anti-paste and anti-drying when barbecuing and roasting chicken. The aluminum coil, because of its strength and hardness, has become an indispensable material in the construction field. Although both have the advantages of lightweight, easy processing and corrosion resistance, they also have disadvantages. Aluminum foil is thin and easy to tear, and aluminum rolls are difficult to bend and deform.
As a general rule, The purer the sand, the clearer the products Silicon and oxygen are the earth's two most abundant elements and together they make silica, one of the earths three most common rock forming minerals. Akshar Minerals Silica sand is high purity natural crystalline silica. It is inherently bright, white, low in moisture and chemically inert in nature. Basically, It is made up of two main element Silica & Oxygen. Silica sand is made up of Silicon Dioxide. There are number of different uses of silica sand in the industrial and commercial sector, from golf courses to glass making . The chemical formula of Silica Sand is SiO2 Characteristics : High Purity Weather Resistant White Appearance Naturally Hard Controlled Particle size Chemically Inert Applications Akshar Minerals Silica sand is used depends on physical, chemical and mechanical characteristics such as grain size, shape color, structure and distribution as well as refractoriness strength and stability. There characteristics can differ depending on how mineral is processed after it is mined. This product gets easily mixed and can be used for high temperature applications like flat glass, furnace tubes and many more due to its excellent thermal expansion, hardness. It yields improved durability and burnish resistance. We make for all type of application in the industries like Glass industries, Sodium Silicate Industry, Golf course & Sport Ground, Adhesive and sealant, Rubber industry, Texture Wall Paint, Sand Blasting, Agro pesticide, Cosmetic industry, Soap & Detergent, Filtration Media, Power Plant & Petroleum, Construction Chemical Industry, Plastic, Fertilizer, Paint, Ceramic, Insulation, Foundry, Ramming Mass, Steel Industry, Landscaping, GRC & GRP Industry, Oil & Petroleum Industry, Oil Exploration & Oil Drilling.
Brief Introduction 1.The pressure-bearing components are forged, so it has better strength and impact toughness; 2.Floating sealing is applied to the cylinder cover and the open/close of the cover is realized by hydraulic power, so it is quick and convenient for changing rams; 3.The auxiliary oil cylinder affords a smaller volume with same function; double ram Cameron U BOP 4.The ram rubber has massive storage volume, and it adopts self-contained sealing; 5.The standard configuration includes a manual locking device, which ensures the ram is closed tightly in case there is a hydraulic pressure loss; 6.Both the manual and hydraulic locking device and the auxiliary oil cylinder can be installed flexibly into different positions according to customers' requirements, and the installation positions can be changed easily.
EQUINAS NBO 60u High Quality Naphthenic Base Oil EQUINAS NBO 60u is a high-quality Naphthenic Base Oil with very good dielectric properties and oxidation stability intended for transformers, switchgears, and other electrical equipment. Naphthenic base oil is a type of mineral oil that is produced through the refining of crude oil. It is characterized by its composition of saturated cyclic hydrocarbons called naphthene. Applications: Naphthenic base oils are used in a wide range of applications, including automotive lubricants, transformer oils, metalworking fluids, rubber and tire manufacturing, and more. They are particularly well-suited for use in applications where low-temperature performance is critical, such as in hydraulic fluids, refrigeration oils, and compressor lubricants Features and Benefits: Low-temperature fluidity: Naphthenic base oil has a low pour point and excellent low-temperature fluidity, making it suitable for use in cold environments. Good solvency: Naphthenic base oil has good solvency, which allows it to dissolve additives and other chemicals that are added to lubricants and other products. Good oxidative stability: Naphthenic base oil has good oxidative stability, which means it can resist degradation caused by exposure to oxygen. Thermal stability: Naphthenic base oil can withstand high temperatures without breaking down or forming deposits. Compatibility: Naphthenic base oil is compatible with a wide range of other materials, including elastomers, seals, and metals. Environmental advantages: Naphthenic base oil is a naturally occurring substance, and its production process generates fewer harmful emissions and waste products than some other types of base oils. Packages size: Available in drums and flexibags Health and Safety: Based on available information, this product is not expected to produce adverse effects on health when used for applications referred to above and the recommendations provided in the Safety Data Sheet (SDS) are followed. The SDS is available upon request through our sales contact office. This product should not be used for purpose other than the applications referred to above. If disposing of used product, take care to protect the environment, follow the local rules and regulations of your local Authority.
Product Specification Power Range : 1.0 HP to 2.0 HP Operating Speed : 0 - 3100 RPM DC Power Range : 900 Wp - 2000 Wp DC Voltage Range : 70 Vmp - 110 Vmp Head Range : 30 Mtr - 90 Mtr Discharge Range : 8000 LPD - 30000 LPD Type of Duty : S1 - Zero Running Cost - Less Maintenance - Eco-Friendly - Simple Installation - Pollution Free Material Of Construction - Motor Part Grade Mechanical Seal : Graphite Ceramic Motor Shaft : Stainless Steel Motor Body Pipe : SS-304 Lower Hosing : Aluminum Diaphragm : High Nitrile butyl rubber Top Cap : Stainless Steel Bottom Plate : Stainless Steel End Cap : Stainless Steel MATERIAL OF CONSTRUCTION SCREW (HELICAL) PUMP Part Grade Outlet : SS-304 Suction : SS-304 Outer Shell : SS-304 Rotor Screw : Stainless Steel Stator : Rubber Coated Alloy MATERIAL OF CONSTRUCTION â?? CENTRIFUGAL PUMP Part Grade Check valve housing : SS-304 Check valve : PC Suction : SS-304 Outer Shell : SS-304 Impeller : POM Bowl : PC Pump Bush : NBR Pump Sleeve : Stainless Steel Pump Shaft : Stainless Steel Coupling / Pump Couple : Stainless Steel
Salient Features Highly efficient 3-phase water filled motor - Easily rewindable - Dynamically balanced design - Extended life with flawless performance - Thrust bearing : Carbon + S.S. material for High thrust load capacity - 100% EC grade copper winding - Presenting world 1st design (design registered 100% fully S.S.-304 investment casting pumps. - Zero maintenance - Superior performance - Sand proof operation - Highly efficient 3-phase water filled motor Product Specification Power Range : 1.0 HP to 20.0 HP Operating Speed : 0 - 2890 RPM Operating Frequency : 0 - 50 Hz Input Solar DC Power Range : 900 Wp, 20000 Wp Input Solar DC Voltage Range : 110 Vmp - 600 Vmp Head Range : 30 Mtr , 220 Mtr Discharge Range : 10000 LPD - 420000 LPD Type of Duty : S1 material of construction - motor Part Grade Body Lock : Spring Steel Stud Ring : M.S. (Zinc Coated) Stator Stamping : CRNGO - M45 Silicon Winding Wire : 100% EC Copper Shaft : SS-420 Rotor Stamping : CRNGO - M45 Silicon Copper Lamination : 100% EC Copper Upper Housing : SS-304 Lower Housing : SS-304 Connection Piece : SS-304 Oil Seal : NBR TB Set : Carbon + SS Base : SS-304 Drain Plug : Brass Couple Sleeve : Stainless Steel Water Bolt : Brass MATERIAL OF CONSTRUCTION PUMP Part Grade Suction : SS-304 Couple : Stainless Steel Couple Counter : SS-304 Rubber Seal : NBR Bush Seal Cover : SS-304 Bowl : SS-304 Impeller : SS-304 Key : SS-410 Bowl Bush : NBR Bush : LTB-4 Middle : SS-304 Cap : NBR Outlet : SS-304
Monoblock pumps - Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features - High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Inbuilt thermal overload protector in al single phase pumpsets upto 2.0 HP - Specially designed for wide voltage operation - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life - Back pull-out design for easy servicing and repair - Double shielded ball bearings, so no need of external lubrication - All Model fitted to Mechanical seal. specification - Power Range : 0.37Kw - 1.5 Kw (0.5 HP - 2.0 HP) - Version : Single Phase, 220-240V, 50Hz AC Supply Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 32 Mtr. - Maximum Flow Rate : 940 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Mechanical Seal - Type of Duty : S1 (Continuous) - Method of Starting : Permanent Split Capacitor (PSC) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 25 X 25, 32 X 25, 40 X 32, 40 X 40, 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 (All size in mm) characteristics of clear cold water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Mechanical Seal : Carbon & Ceramic Motor Shaft : EN-8 Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Plastic
Falcon regenerative monoset pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. Salient Features High operating efficiency resulting in lower power consumption. - Good suction lift characteristics. - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. - All Model fitted to Mechanical seal. specification Power Range : 0.37 Kw - 0.75 Kw (0.5 HP - 1.0 HP) - Version : Single Phase, 220-240V, 50Hz AC Supply - Speed : 1440 RPM - Maximum Total Head : 18 Mtr. - Maximum Flow Rate : 4200 LPH - Maximum Suction Lift : 8 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Mechanical Seal - Type of Duty : S1 (Continuous) - Direction of Rotation : Single Phase, Clockwise from driving end - Nominal Pumpset Size (Suction X Delivery) : 25mm X 25mm Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 material Of construction - Motor Part Name Material Mechanical Seal : Carbon & Ceramic Motor Shaft : SS-410 Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : Brass Cooling Fan : Plastic
Highly efficient 3-phase Air Cooled motor - 100% EC grade copper winding - Easily Rewindable - Good suction lift characteristics - Sustainable uniform performance for years - Ensures long life durability - Optimized Hydraulic & Mechanical Design - Improved efficient performance - Excellent output in Low Radiation - Dynamically balanced design - Double shielded ball bearings, so no need of external lubrication - Mechanical seal or stuffing box is provided as per customers requirement - Zero maintenance Product Specification Power Range : 1.0 HP to 10.0 HP Operating Speed : 0 2890 RPM Operating Frequency : 0 - 50 Hz Input Solar DC Power Range : 900 Wp, 10000 Wp Input Solar DC Voltage Range : 110 Vmp, 600 Vmp Head Range : 10 Mtr, 50 Mtr Discharge Range : 45000 LPD - 405000 LPD Max. Suction Head : 7 Mtr Type of Duty : S1 Material Of Construction Part Grade Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminium
Salient Features Highly efficient 3-Phase Water Filled Motor - 100% EC grade copper winding - Easily Rewindable - Motor Designed with Higher Cooling Effect Ensures Longer Life - Sustainable uniform performance for years - Ensures long life durability - Optimized Hydraulic & Mechanical Design - Improved efficient performance - Excellent output in Low Radiation - Dynamically balanced design - Zero maintenance Product Specification Power Range : 3.0 HP to 10.0 HP Operating Speed : 0 - 2890 RPM Operating Frequency : 0 â?? 50 Hz Input Solar DC Power Range : 3000 Wp, 10000 Wp Input Solar DC Voltage Range : 330 Vmp , 600 Vmp Head Range : 10 Mtr , 50 Mtr Discharge Range : 126000 LPD , 425000 LPD Type of Duty : S1 Material Of Construction Part Grade Oil Seal : Nitrile butyl rubber Motor Shaft : SS - 420 Motor Body : Cast Iron / J4 Motor Bush : LTB-4 / Teflon Thrust bearing assembly : SS - 420 & Carbon Base : Cast Iron Bracket : Cast Iron Flange : Cast Iron Casing : Cast Iron Impeller : Cast Iron
Monoblock Pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. - Mechanical seal is provided as per customers requirement Specification - Power Range : 2.2 Kw - 11.2 Kw (3.0 HP - 15.0 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 65 Mtr. - Maximum Flow Rate : 1450 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 100 X 80 and 100 X 100 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 mÃ?/sec (max.) - Ph Value : 6.5 to 8.5 Material of construction - motor Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminium
Monoblock pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. Salient Features High operating efficiency resulting in lower power consumption. - Good suction lift characteristics. - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. specification - Power Range : 1.5 Kw - 5.5 Kw (2.0 HP - 7.5 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 1440 RPM - Maximum Total Head : 12 Mtr. - Maximum Flow Rate : 3160 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase - Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 80 X 80, 100 X 100, 125 X 125, 150 X 150 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminum
Drained battery scrap (free of battery acid/fluid) including lead plates and plastic/rubber casing complete with caps. Purity : Complete Battery with full contents, except the liquid Car batteries are treated as hazardous waste. Material Origin : Car Battery / Van Battery / marine batteries and industrial traction batteries. Drained Lead Car Battery Scraps (Rains) Drained Lead-Acid Battery Scrap (RAINS per ISRI Specifications). Our Acid Battery Scrap on 99.99%. . Automotive Waste Batteries completely washed, cleaned with lead acid contents. RAINs per ISRI Specifications) (Product Detailed SpecWET/DRY WHOLE INTACT CAR LEAD BATTERIES(RINKs and ifications) height :116mm and whight :310 gr height :123mm and whight :350 gr Used Auto Battery Scrap Drained lead battery scraps Lead Battery Plate Scrap Type Battery Scrap 20D 16H Lead Battery Plates Scrap Lead Battery Plate Scrap Type soft lead scrap Drained / Dry Whole Intact Lead Batteries (RAINS) Lead Battery Scrap >> Drained / Dry Whole Intact Lead Batteries (RAINS) SCRAP DRAINED/DRY WHOLE INTACT LEAD BATTERIES : To be free of any liquid. Cases to be either plastic or rubber and be complete including caps. Non-lead (ni-cad, ni-fe, carbonaire, etc.) not acceptable. Seller Listings Drained / Dry Whole Intact Lead Batteries (RAINS) 6V1.3AH sealed lead acid battery. 1/Product Specification: Item No.:DHB613; Voltage:6V; Normal capacity:1.3AH/20hr; Dimension(L*W*H):97*24*52mm; Total height(with terminal):57mm; Weight:0.30kg; 2/Product Feature: (1)Maintenance-free operation.there is no need to check specific gravity of the electrolyte or add water to battery during float service life. (2)Low self-discharge rate, small internal resistance. (3)The unique construction and sealing techniques of the battery, add the ABS plastic crust that guarantee leakproof operation in and position with no adverse effect to capacity or service life. (4)With our high quality lead-tin-calcium alloy grids, it has a long usage life and deep discharge recoverability. (5)No pollution and no harm.
Blowout preventer (BOP) BOP is shut in the well for oil testing, workover, well completion and operating process to prevent the blowout accident, totally enclosed and semi-closed two functions into one, has a simple structure, easy to operate, resistant to high-pressure characteristics is used to prevent blowouts safety oilfield sealing wellhead. Oil drilling, installed at the wellhead casing head, used to control the high pressure oil, gas, water blowout. Wells of oil and gas pressure is high, the BOP can be the wellhead closed (shut). The shutter has four, alternatively bullied invaded mud, increasing the pressure of the borehole fluid column, so as to suppress the high-pressure oil and gas discharged from the drill pipe is pressed into the heavy mud. Its type sub-ordinary blowout preventer, of universal blowout preventers and rotating blowout preventer. Ordinary BOP ram with full-and semi-closure, full closure type blowout preventer can seal the entire wellhead; semi-sealed shut wellhead annular cross-section of drill pipe exists. Universal BOP can start in case of emergency to cope with any size drill and empty wells. Parts Lake Petro supplies apply to below BOP: Brand: SHENKAI BOP. RONGSHENG BOP ETC OTHER FAMOUS BRAND BOP Type:Annular BOP, Single Ram BOP, Double Ram BOP, Shear Ram BOP Working pressure:2000psi-15000psi(14 Mpa-105Mpa) Operating temperature:-18deg--121deg Bore size:7 1/16"-21 1/4" Top & bottom connection:Flanged,studded
