The coloring fibers are positioned in a central loose tube. The PSP is longitudinal covering. Parallel steel wire is inside the PE sheath. Between steel strip and loose tube is filled with a water-blocking compound. Characteristics: Good mechanical and temperature resistant performance. Crush resistance, water blocking and flexibility Geometrical Characteristics: Number of Fibers 2-12 Cable Diameter (mm) 9.8 Cable Weight (kg/km) 110 Mechanical Characteristics: Max Load (N) Long Term 600 Short Term 1500 Crush Resistance (N/100mm) Long Term 300 Short Term 1000 Bending Radius (MM) Dynamic 100 Static 200 Fiber Cladding: Fiber Type (core/cladding dimension) 8.3/125, 50/125, 62.5/125 Transmission Characteristics: SMF 50/125 62.5/125 1310/1550(nm) 850/1300(nm) 850/1300(nm) Max. Attenuation (dB/km) 0.45/0.30 3.5/1.5 3.5/1.5 AVG. Attenuation (dB/km) 0.40/0.25 3.0/1.0 3.0/1.0 Min. Bandwidth (MHz/km) 400/400 160/500 Environmental Characteristics: Storage/Operating Temperature -40íµí½+70íµ
Fiber Optic Cables
Fiber Optic Patch Codes
1single modeG652DG655,G657A1,G657A2,G657B3) and multimode(OM1,OM2,OM3,OM4) 2,simplex,duplex,multi core 3,armored and non-armored 4,Storage temperature(-40+60) 5,Adopted to Outdoor distribution 6,uitable for aerial (self- supporting),decrease cost 7,Long distance and local area network communication 8,Stainless steel or gaivanized steel self-supporting 9,Excellet mechanical and environmental performance
Feature: Steel-wire parallel member,filler protect tube fiber steel tape amored; Excellent mechanical and environmental performance; compact structure; can be installed conveniently and operated simply. Application: Adopted to Outdoor distribution; Suitable for aerial .pipeline laying method; Long distance and local area network communication.
The fibers, 125μm, are positioned in a loose tube made of a high modulus plastic. The tubes are filled with a water-resistant filling compound. A Fiber Reinforced Plastic (FRP) locates in the center of core as a non-metallic strength member. The tubes (and fillers) are stranded around the strength member into a compact and circular core. An Aluminum Polyethylene Laminate (APL) is applied around the cable core. Then the cable core is covered with a thin polyethylene (PE) inner sheath, which is filled with jelly to protect it from water ingress. After a corrugated steel tape armor is applied, the cable is completed with a PE outer sheath.
This cable has been designed for long haul direct / backbone application. Our stranded loose tube design provides stable performance over a wide temperature range and is compatible with any telecommunications-grade optical fiber. Direct Buried type Fiber Optical Cables are designed for easy and economical installation. The stranded loose tubes contain thixotropic jelly but the cable core is based on dry-block construction. Incorporation of Dry Water Block Technology eliminates the need for traditional jelly filled water blocking methods, thus providing efficient and craft-friendly cable installation. The thixotropic jelly is used to fill the buffer tubes to prevent water ingress. Steel Tape Armoring provides a rodent protection, length markings in meters for easy determination of cable length. Extra Strength cable can also be delivered with Peripheral Strength Members. Features & Application òExcellent optical, mechanical & environmental performance òHigh strength-to-weight ratio òCSM dielectric type û Fiber Reinforced Plastic òDry block construction òHigh tensile strength òHigh crush strength òCorrosion resistance òKINK resistance òVery light weight òVery flexible & small bending radius òLong haul / backbone application òJunction communication systems òAll dielectric applications òCATV applications. Construction Parameters Fiber Count 02 û 144 Fibers Color of Loose Tube Blue , Orange , Green , Brown , Grey , White, Red & Black Loose Tube Material Polybutylene Terephthalate (PBT) Loose Tube Filling Material Thixotropic Jelly Filler Material Medium Density/High Density Polyethylene (MDPE/HDPE) Central Strength Member Fiber Reinforced Plastic (FRP) û Non Metallic Core Moisture Protection Methodology Dry Block Design, Water Blocking Yarns/Tapes Second (Outer) Sheath Material High Density Polyethylene (HDPE) Printing on Outer Sheath Engraved Hot Foil or Inkjet Printing Nominal Cable Delivery Length (km) 4 KM ¦ 3%.
This cable has been designed for long haul direct / backbone application. Our stranded loose tube design provides stable performance over a wide temperature range and is compatible with any telecommunications-grade optical fiber. Direct buried type fiber optical cable are designed for easy and economical installation. The stranded loose tubes contain thixotropic jelly but the cable core is based on dry-block construction. Incorporation of dry water block technology eliminates the need for traditional jelly filled water blocking methods, thus providing efficient and craft-friendly cable installation. The thixotropic jelly is used to fill the buffer tubes to prevent water ingress. Steel tape armoring provides a rodent protection, length markings in meters for easy determination of cable length. Extra strength cable can also be delivered with peripheral strength members. Features & application Excellent optical, mechanical & environmental performance High strength-to-weight ratio Csm dielectric type û fiber reinforced plastic Dry block construction High tensile strength High crush strength Corrosion resistance Kink resistance Very light weight Very flexible & small bending radius Long haul / backbone application Junction communication systems All dielectric applications Catv applications. Construction Parameters Fiber Count As per CustomerÆs Requirement No. of Loose Tube As per CustomerÆs Requirement G.655 As per CustomerÆs Requirement G.652 As per CustomerÆs Requirement Loose Tube Material Polybutylene Terephthalate (PBT) Loose Tube Filling Material Thixotropic Jelly Filler Material Medium Density/High Density Polyethylene (MDPE/HDPE) Central Strength Member Fiber/Glass Reinforced Plastic (FRP/GRP) Armoring Corrugated Steel Tape Armoring Peripheral Strength Member (if required) Aramid / Glass Yarn Core Moisture Protection Methodology Dry Block Design, Water Blocking Yarns/Tapes Outer Sheath Material High Density Polyethylene (HDPE) Printing on Outer Sheath Engraved Hot Foil or Inkjet Printing Nominal Cable Delivery Length (km) 4 KM ¦ 3%.
Product description This cable has been designed for aerial application with flat type construction. Our stranded loose tube design provides stable performance over a wide temperature range and is compatible with any telecommunications-grade optical fiber. This aerial type fiber cable is designed for easy and economical installation with a sufficient tensile strength to overcome wind pressures and ice loadings. Features & application Excellent optical, mechanical & environmental performance Csm dielectric type û fiber reinforced plastic High tensile strength High crush strength Aerial application Application in lan, wan, especially in ftth networks Easy to clamp and install Can bear ice loads and high wind pressures. Construction Parameters Fiber Count 02 to 12 Fiber Fiber Type G.652.D Loose Tube Material Polybutylene Terephthalate (PBT) Loose Tube Filling Material Thixotropic Jelly Sheath Material High Density Polyethylene (HDPE) Printing on Outer Sheath Engraved Hot Foil or Inkjet Printing Nominal Dimensions Width : 7.0 + 0.5mm , Height : 3.5 + 0.3mm Nominal Cable Delivery Length (km) 2 KM + 3% . Mechanical Characteristics Tensile Strength (N) 600 Tensile Strength (N) (Installation) 1000 Crush Strength (N) 2,000 Minimum Bending Radius (mm) 75 Temperature Operating Range -10 to +70¦C.
Please quote for the following wholesale product requirement - Product Name: Optical Fiber Cables Specifications: Type: Optical Fiber (POF), Transparent Glass Or Plastic Fibers Voltage: Low & Medium Material: Plastic Fiber, Rubber Use: Industrial, Construction Size: Customized Packaging Terms : Standard
our company has engaged in fiber communication products for 15 years, our main products are optical cable and FTTx system products,including Outdoor Fiber Optical Cable,Indoor Fiber Optical Cable,Data Cable,Municipal Telephone Cable,etc. For the individual or enterprise who has the requirement for setting up the optical cable factory or communication product assembly factory, we will provide service of factory planing and designing, production line installation and commissioning, product design and testing , production process control and technic support. We supply all the raw materials too. KINGFIBER is devoted to build a win-win relationship with our partner. If you have any requirements in fiber communication products, please contact me at any time,and I will provide you more details with catalogue.Thank you. Best regards, Andy Ma Vice General Manager Henan Kingfiber Industry Co.,Ltd
Optical Fiber Cable : We carry brand names such as Asahi/Lucina and Showa Electric Wire Cable
Gyfta53 fiber optic cable characteristics: fiber optical cable 1.Accurate fiber excess length ensures good mechanical and temperature performance Gyfta53 fiber optic cable brief introduction The fibers, either of single-mode or multi-mode type, are placed in a loose tube made of a high modulus plastic. The tubes are filled with a water-resistant filling compound. A piece of fiber reinforced plastic (frp) locates in the center of core as a non-metallic strength member. The tubes(and fillers) are stranded around the strength member into a compact and circular cable core. An aluminum polyethylene laminate (apl) is applied around the cable core, which is filled with the filling compound to protect it from water ingress. Then the cable core is covered with a thin pe inner sheath. After the psp is longitudinally applied over the inner sheath, the cable is completed with a pe outer sheath. Gyfta53 fiber optic cable pictures: 1.Gyfta53-fiber-optic-cable Gyfta53 fiber optic cable fiber optical cable Gyfta53 fiber optic cable paramters: fiber optical cable Gyfta53 fiber optic cable Wooden drum // special package can be customized.Inspection certificate of fumigation should be notified before production as it will take 7 days from application to approval.
Optic fiber cable for duct, direct burial, aerial application 3km per wooden drum optic fiber cable or by customers' require
1.Gyts fiber optic cable. 2.Application:aerial, duct. 3.Long-distance communication, lan etc. 4.Armored steel tape. 1/2/3 km per a wooden drum
Cable type G.652d/g657a, pvc, lszh, simplex or duplex, 0.9, 2.0, 3.0mm Fiber type Smf-28e, sm 9/125um, mm 50&62.5/125um Polish method Upc, pc, spc, apc Connector Fc, sc, lc, st, e2000, din, d4, sma, fddi, mpo/mtp Insertion loss 0.1db (for single mode master) 0.25db (for single mode standard) 0.25db (for multimode) Return loss (for single mode) Upc 50db Spc 55db Apc 60db (typ.65db) Repeatability ¡¨¤0.1db Operating temperature -40 c to 85 ¡ãc Geometry requirement (for single mode) Ferrule end face radius7mm r 12mm (for apc) 10mm r 25mm (for standard) Apex offset 30 |¨¬m (for master) Apex offset 50 |¨¬m (for standard) Undercut -50nm u 50nm 1pc/plastic bag, 1500pcs/carton box
Fiber patch cord Fiber optic accessories.
Bulk fiber cables Panels and connectivity Assemblies and patch cables.
Control :by technician Needed air :10.5 bar 12 m³/min.(duct 40 hdp) Air engine : double effective, 740 watt (2 pieces) Needed air for engines : 6 bar-1.6m³/min. Cable installing velocity : 0, 30, 50m/min. Lay down power :80~85 kg. Dimensions (width x lenght x height) : 365mm x 330mm x 540mm Weight of machine :46kg. In chrome box.
Optical fiber cables
